File Info : application/pdf, 300 Pages, 31.11MB

2007 Spectra Owners Manual EN

kia, the company
Congratulations! Your selection of a Kia was a wise investment. It will give you years of driving pleasure. Now that you are the owner of a Kia vehicle, you'll probably be asked a lot of questions about your vehicle and the company like "What is a Kia?", "Who is Kia?", "What does `Kia' mean?". Here are some answers. First, Kia is the oldest car company in Korea. It is a company that has thousands of employees focused on building high-quality vehicles at affordable prices. The first syllable, Ki, in the word "Kia" means "to arise from to the world" or "to come up out of to the world." The second syllable, a, means "Asia." So, the word Kia, means "to arise from" or "to come up out of Asia to the world."
Drive safely and enjoy your Kia!

Foreword

Thank you for choosing a Kia vehicle.
When you require service, remember that your dealer knows your vehicle best. Your dealer has factory-trained technicians, recommended special tools, genuine Kia replacement parts and is dedicated to your complete satisfaction.
Because subsequent owners require this important information as well, this publication should remain with the vehicle if it is sold.
This manual will familiarize you with operational, maintenance and safety information about your new vehicle. It is supplemented by a Warranty and Consumer Information manual that provides important information on all warranties regarding your vehicle. We urge you to read these publications carefully and follow the recommendations to help assure enjoyable and safe operation of your new vehicle.
Kia offers a great variety of options, components and features for its various models.
Therefore, the equipment described in this manual, along with the various illustrations, may not all be applicable to your particular vehicle.

The information and specifications provided in this manual were accurate at the time of printing. Kia reserves the right to discontinue or change specifications or design at any time without notice and without incurring any obligation. If you have questions, always check with your Kia Dealer. We assure you of our continuing interest in your motoring pleasure and satisfaction in your Kia vehicle.
© 2007 Kia Motors Corp. All rights reserved. Reproduction by any means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Kia Motors Corporation. Printed in Korea

Introduction

Your vehicle at a glance

Knowing your vehicle

Driving your vehicle

table of contents

Driving tips

In case of an emergency

Maintenance

Specifications

Index

Introduction

How to use this manual / 1-2

Vehicle break-in process / 1-3

Introduction

HOW TO USE THIS MANUAL

We want to help you get the greatest The general layout of the manual is possible driving pleasure from your provided in the Table of Contents. A

WARNING

vehicle. Your Owner's Manual can good place to start is the index; it has A WARNING indicates a situation

1 assist you in many ways. We strong- an alphabetical listing of all informa- in which harm, serious bodily

ly recommend that you read the tion in your manual.

injury or death could result if the

entire manual. At the very least, you Sections: This manual has eight secmust read the WARNING and CAU- tions plus an index. Each section

warning is ignored.

TION sections spread throughout the begins with a brief list of contents so

manual, which are easily recognized you can tell at a glance if that section by their special markings. These sec- has the information you want. tions have precautions that must be

CAUTION
A CAUTION indicates a situation

4 5 6 7

followed to prevent personal injury or death.
Illustrations complement the words in this manual to best explain how to enjoy your vehicle. By reading your manual, you learn about features, important safety information, and driving tips under various road conditions.

You'll find various WARNING's, CAUTION's, and NOTICE's in this manual. These WARNING's, CAUTION's and NOTICE's were prepared to enhance your personal safety and continued satisfaction with Kia vehicle. You should carefully read and follow ALL procedures and recommendations provided in these

in which damage to your vehicle could result if the caution is ignored.
NOTICE
A NOTICE indicates interesting or helpful information is being provided.

WARNING's, CAUTION's and

NOTICE's.

VEHICLE BREAK-IN
PROCESS
No special break-in period is needed. By following a few simple precautions for the first 1,000 km (600 miles) you may add to the performance, economy and life of your vehicle.
· Do not race the engine.
· Do not maintain a single speed for long periods of time, either fast or slow. Varying engine speed is needed to properly break-in the engine.
· Avoid hard stops, except in emergencies, to allow the brakes to seat properly.
· Avoid full-throttle starts.

Introduction
1 2 3 4 5 6 7 8 9
13

Your vehicle at a glance

Interior overview / 2-2 Instrument panel overview / 2-3

Engine compartment / 2-4

Your vehicle at a glance INTERIOR OVERVIEW
1 2 3 4 5 6 7 8 9
22

1. Door lock/unlock button 2. Outside rearview mirror control switch* 3. Power window switches* 4. Master power door lock control* 5. Master power window control lock* 6. Vent controls 7. Instrument cluster 8. Steering wheel 9. Steering wheel tilt* 10. Trunk release button 11. Instrument panel illumination* 12. TCS button* 13. Hood release lever 14. Brake pedal 15. Accelerator pedal 16. Fuel filler lid release lever * : if equipped
OLD006002N

INSTRUMENT PANEL OVERVIEW

Your vehicle at a glance

1. Driver's Air bag*

2. Light control / Turn signals

3. Instrument cluster

4. Wiper/Washer

5. Ignition switch

6. Aux 7. Hazard

8. Climate control system

9. Shift lever*

10. Passenger's air bag*

11. Glove box

12. Audio controls*

13. Auto cruise controls* * : if equipped

OLD006003N
23

Your vehicle at a glance ENGINE COMPARTMENT
1 2 3 4 5 6 7 8 9
24

1. Power steering fluid reservoir 2. Engine oil filler cap 3. Brake fluid reservoir 4. Air cleaner 5. Fuse box 6. Negative battery terminal 7. Positive battery terminal 8. Auto transaxle oil dipstick* 9. Radiator cap 10. Engine oil dipstick 11. Engine coolant reservoir 12. Windshield washer fluid reservoir * : if equipped
OLD056002

Keys / 3-2 Remote keyless entry / 3-3

Immobilizer system / 3-6

Door locks / 3-8

Knowing your vehicle

Windows / 3-13 Seat / 3-16

Safety belts / 3-27

Air bag - Advanced supplemental restraint system / 3-50

Trunk / 3-76

Hood / 3-78 Fuel filler lid / 3-80

Mirrors / 3-83

Interior lights / 3-87

Storage compartment / 3-88

Interior features / 3-90

Sunroof / 3-94

Luggage net / 3-97

Antenna / 3-98 Audio system / 3-99

Knowing your vehicle

KEYS

WARNING - Ignition key

Leaving children unattended in

a vehicle with the ignition key is

dangerous even if the key is not

in the ignition. Children copy adults and they could place the

key in the ignition. The ignition

key would enable children to operate power windows or other

controls, or even make the vehi-

OUN046100L

OUN026060 cle move, which could result in

The key code number is stamped on the plate attached to the key set. Should you lose your keys, this number will enable an authorized Kia

Key operations Master key Used to start the engine, lock and

serious bodily injury or even death. Never leave the keys in your vehicle with unsupervised children.

Dealer to duplicate the keys easily. unlock the doors, and open the trunk Remove the plate and store it in a (if equipped).

safe place. Also, record the code number and keep it in a safe and

handy place, but not in the vehicle.

WARNING
Use only Kia original parts for the ignition key in your vehicle.

If an aftermarket key is used, the

ignition switch may not return

to ON after START. If this happens, the starter will continue to

operate causing damage to the

starter motor and possible fire

due to excessive current in the

wiring.

Knowing your vehicle

REMOTE KEYLESS ENTRY (IF EQUIPPED)

Type A

Lock (1)

Panic (3) (if equipped)

All doors are locked and the hazard The horn sounds and hazard lamp

lamp flash once if the lock button is will flash for about 27 seconds if this

pressed.

button is pressed for more than 0.5 1

seconds.

Type B

Unlock (2)
Driver's door is unlocked and the hazard lamp will flash twice if the unlock button is pressed once. All

To stop the panic operation, press any button except panic on the transmitter.

2 3

OLD026001 doors are unlocked if the unlock but- Trunk lid open (4) (if equipped)

ton is pressed twice within 4 sec- The trunk lid opens if this button is 4

onds.

pressed for more than 0.5 seconds.

After depressing this button, the doors will be locked automatically

unless you open them within 30 sec-

onds.

OLD026002

(1) Lock button

(2) Unlock button

(3) Panic button

(4) Trunk lid open button

Knowing your vehicle

1 2 3

NOTICE
The transmitter will not work if any of following occur: - The ignition key is in ignition
switch. - You exceed the operating distance
limit (about 30 m [100 feet]). - The battery in the transmitter is
weak. - Other vehicles or objects may be

CAUTION
Keep the transmitter away from water or any liquid. If the keyless entry system is inoperative due to exposure to water or liquids, it will not be covered by your manufacturer vehicle warranty.

This device complies with Industry Canada Standard RSS210. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

4 5 6

blocking the signal. - The weather is extremely cold. - The transmitter is close to a radio
transmitter such as a radio station or an airport which can interfere with normal operation of the transmitter. When the transmitter does not work correctly, open and close the door

Operational distance may vary depending upon the area the transmitter is used in. For example, if the vehicle is parked near police stations, government and public offices, broadcasting stations, military installations, airports, or transmitting towers, etc.

WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

7 with the ignition key. If you have a

problem with the transmitter, con-

8 tact an authorized Kia Dealer.

Knowing your vehicle

CAUTION

OMG035137

The keyless entry system trans-

mitter is designed to give you 1
years of troublefree use, howev-

er it can malfunction if exposed
to moisture or static electricity. 2

If you are unsure how to use

your transmitter or replace the battery, contact an authorized

Kia dealer.

HNF2005

Battery replacement

2. Replace the battery with new one. For replacement transmitters, see an

Transmitter uses a 3 volt lithium battery which will normally last for several years. When replacement is necessary, use the following procedure.

When replacing the battery, make Authorized Kia Dealer for reprogramsure the battery positive "+" sym- ming.

bol faces up as indicated in the

illustration.

CAUTION

1. Insert a slim tool into the slot and gently pry open the transmitter

3. Install the battery in the reverse order of removal.

· Using the wrong battery can cause the transmitter to mal-

center cover.

function. Be sure to use the

correct battery. · To avoid damaging the trans-

mitter, don't drop it, get it wet,

or expose it to heat or sunlight.

Knowing your vehicle

IMMOBILIZER SYSTEM (IF EQUIPPED)

The Immobilizer unit checks the sig- NOTICE

nal and determines whether the igni- When starting the engine, do not use

tion key is valid.

the key with other immobilizer keys

If the key is determined to be valid, around. Otherwise the engine may

the engine will start.

not start or may stop soon after it

If the key is determined to be invalid, starts. Keep each key separately not

the engine will not start.

to have any malfunction after you

receive your new vehicle.

To deactivate the immobilizer system:

This device complies with Industry Canada Standard RSS-

OHD046100 Insert the ignition key into the key 210. Operation is subject to the fol-

Your vehicle is equipped with an electronic engine immobilizer system to reduce the risk of unauthorized

cylinder and turn it to the ON position.

lowing two conditions:
1. This device may not cause interference, and

vehicle use. Your immobilizer system is com-

To activate the immobilizer system:

2. This device must accept any interference, including interference that

prised of a small transponder in the Turn the ignition key to the OFF posi-

may cause undesired operation of

ignition key, and antenna coil in the tion. The immobilizer system actikey cylinder and Immobilizer unit in vates automatically. Without a valid

the device.

the instrument panel.

ignition key for your vehicle, the

8 With this system, whenever you engine will not start.

WARNING

insert your ignition key into the igni-

Changes or modifications not

tion switch and turn it to ON, the antenna coil in the ignition switch

expressly approved by the party responsible for compliance

receives a signal from the transpon-

could void the user's authority

der in the ignition key and then sends

to operate the equipment.

the signal to the Immobilizer unit.

Knowing your vehicle

Limp home (override) procedure

3. To enter the first digit (in this example "2"), turn the ignition key

CAUTION

When you turn the ignition key to the ON position, if the IMMO indicator remains on continuously after blinking 6 times, your transponder equipped in the ignition key is out of order. You cannot start the engine without the lime home procedure. To start the engine, you have to input your password by using the ignition switch.

to the ON and ACC position twice. Perform the same procedure for the next digits between 3 seconds and 10 seconds (for example, for "3", turn the ignition ON and ACC 3 times).
4. If all of the digits have been input successfully, you have to start the engine within 10 seconds. If you attempt to start the engine after 10

The transponder in your ignition key is an important part of the immobilizer system. It is designed to give years of trouble free service, however you should avoid exposure to moisture, static electricity and rough handling. Immobilizer system malfunction could occur.

1 2 3 4

seconds, the engine will not start

The following procedure is how to

and you will have to input your

CAUTION

password again.

Do not change, alter or adjust

input your password of "2345" as an example.
1. Turn the ignition key to the ON posi-

After performing the limp home procedure, you have to see an authorized Kia dealer immediately to

the immobilizer system because it could cause the immobilizer system to malfunction and

tion. The IMMO indicator ( ) will inspect and repair your ignition key should only be serviced by an

blink 6 times and remain on indicat- or immobilizer system.

authorized Kia dealer.

ing the beginning of the limp home

Malfunctions caused by improp-

procedure.
2. Turn the ignition key to the ACC position.

CAUTION
If you cannot start your engine in spite of limp home procedure, have your vehicle towed by an

er alterations, adjustments or modifications to the immobilizer system are not covered by your vehicle manufacturer warranty.

8 9

authorized Kia dealer for

inspection and necessary

repairs.

Knowing your vehicle

DOOR LOCKS

Lock

Unlock

· Once the doors are unlocked, they may be opened by pulling the door handle.
· When closing the door, push the door by the hand. Make sure that doors are closed securely.

1LDA2004

Operating door locks from

5 outside the vehicle

· Turn the key toward rear of vehicle

to unlock and toward front of vehicle to lock.

· Turn the key to the right once to

unlock the driver's door and to the

right twice within 4 seconds to

unlock all doors. (if equipped) · Turn the key to the left once to

unlock the passenger's door and to

the left twice within 4 seconds to

unlock all doors. (if equipped)

· Doors can also be locked and unlocked with the transmitter key.

OLD036900N
To lock a door without the key, push the inside door lock button (1) or door lock switch (2, if equipped) to the "LOCK" position and close the door (3).
WARNING
Always remove the ignition key, engage the parking brake, close all windows and lock all doors when leaving your vehicle unattended.

Knowing your vehicle

NOTICE
If the door is locked/unlocked multiple times in rapid succession with either the vehicle key or door lock switch, the system may stop operating temporarily in order to protect the circuit and prevent damage to system components.

Unlock

· If the inner door handle of driver's

(front passenger's, if equipped)

Lock

door is pulled when the door lock

button is in lock position, the button 1
is unlocked and door opens.

· Front doors cannot be locked if the ignition key is in the ignition switch

and door is open.

· If you lock the front door with door 3

lock button, all vehicle doors will

1LDA2006

lock automatically. (if equipped)

Operating door locks from

inside the vehicle

With the door lock button

· To unlock a door, push the door lock button (1) to the "Unlock" posi-

tion. The red mark (2) on button will

be visible.

· To lock a door, push the door lock

button (1) to the "Lock" position. If the door is locked properly, the red

mark (2) on the door lock button

will not be visible.

· To open a door, pull the door han-

dle (3) outward.

Knowing your vehicle

Driver's side
1 2 3 4
Passenger's side (if equipped)
5

1LDA2007

· When pushing down on the front portion (1) of the central door lock switch, all vehicle doors will lock.
· When pushing down on the rear portion (2) of the switch, all vehicle doors will unlock.
· However, if the key is in the ignition switch and any front door is open, the doors will not lock when the front portion of central door lock switch is pressed.

8
1LDN2007
9 With central door lock switch
(if equipped) It is operated by depressing the door lock switch. If any door is open when the switch is depressed, the door will remain locked when closed.
3 10

WARNING
· The doors should always be fully closed and locked while the vehicle is in motion to prevent accidental opening of the door. Locked doors will also discourage potential intruders when the vehicle stops or slows.
· Be careful when opening doors and watch for vehicles, motorcycles, bicycles or pedestrians approaching the vehicle in the path of the door. Opening a door when something is approaching can cause damage or injury.

Knowing your vehicle

WARNING - Unlocked
vehicle
Leaving your vehicle unlocked can invite theft or possible harm to you or others from someone hiding in your vehicle while you are gone. Always remove the ignition key, engage the parking brake, close all windows and lock all doors when leaving your vehicle unattended.

WARNING - Unattended

children

An enclosed vehicle can

become extremely hot, causing

death or severe injury to unattended children or animals who

cannot escape the vehicle.

Furthermore, children might operate features of the vehicle

that could injure them, or they

could encounter other harm,

1LDA2008

possibly from someone gaining entry to the vehicle. Never leave children or animals unattended

Rear door child safety lock The child safety lock is provided to

in your vehicle.

help prevent children from acciden-

tally opening the rear doors from inside the vehicle. The rear door

safety locks should be used whenev-

er children are in the vehicle.

3 11

Knowing your vehicle

1. Open the rear door.

2. Push the child safety lock located

WARNING - Rear door

on the rear edge of the door to the

locks

"lock" position. When the child If children accidentally open the

safety lock is in the "lock ( )" rear doors while the vehicle is in

position, rear door will not open motion, they could fall out and when the inner door handle is be severely injured or killed. To

pulled inside the vehicle.

prevent children from opening

Lock

Unlock

3 4

3. Close the rear door.
4. To open the rear door, pull the outside door handle.

the rear doors from the inside, the rear door safety locks should be used whenever children are in the vehicle.

Even though the doors may be unlocked, the rear door will not open

Rear hatch (if equipped)

5 by pulling the inner door handle (1)

Opening the rear hatch

until rear door child safety lock is
6 unlocked ( ).

· Rear hatch is locked or unlocked with a key.

· To open the rear hatch, insert the

key into the lock, turn it to the unlock position (1) and pull up the

rear hatch by pressing the handle

(2).

· You can also lock/unlock the latch

(but not release it) with the central door lock system (if equipped).

· If unlocked, the rear hatch can be opened by pressing the handle (2) and pulling the hatch up.

3 12

WINDOWS

Knowing your vehicle

Power windows (if equipped)

(1) Driver's door power window

switch (2) Front passenger's door power

window switch

(3) Rear door (left) power window 2

switch

(4) Rear door (right) power window switch

(5) Window opening and closing (6) Automatic power window down*

(Driver's window)

(7) Power window lock switch

*: if equipped

9
OLD026010

3 13

Knowing your vehicle

The ignition switch must be in the ON position for power windows to operate. Each door has a power window
1 switch that controls the door's win-
dow. However, the driver has a power window lock switch which can block
2 the operation of passenger windows.

The power windows can be operated

for approximately 30 seconds after the ignition key is removed or turned

to the ACC or LOCK position.
4 However, if the front doors are

OUN026012

OUN026011

5 6 7

opened, the power windows cannot be operated even within the 30 seconds after the ignition key removal.
While driving, if you notice buffeting and pulsation (wind shock) with either side window open, you should open the opposite window slightly to reduce the condition.

Window opening and closing
The driver's door has a master power window switch that controls all the windows in the vehicle.
To open or close a window, press down or pull up the front portion of the corresponding switch to the first detent position (5).

Auto down window (if equipped) (Driver's window)
Depressing the power window switch momentarily to the second detent position (6) completely lowers the driver's window even when the switch is released. To stop the window at the desired position while the

window is in operation, pull up the

switch momentarily to the opposite

direction of the window movement.

If the power window is not operated correctly, the automatic power win-

dow system must be reset as follows:

1. Turn the ignition switch to the ON position.

3 14

Knowing your vehicle

2. Close driver's window and continue pulling up on driver's power

CAUTION

window switch for at least 1 sec- To prevent the power window

ond after the window is complete- system from the possibility of

ly closed.

damage, do not open or close

two windows at the same time.

This will also ensure the

longevity of the fuse.

WARNING

· Make sure heads and hands

3FDA2015

are safely out of the way before Manual windows (if equipped)

closing a window.

Use the window crank to open and 5

· Do not allow children to play close each window.

with the power windows. Keep

OLD026013

the driver's door power window

lock switch in the LOCK posi-

Power window lock switch · The driver can disable the power

tion (depressed). Serious injury can result from unintentional

window switches on a passenger

window operation by the child.

door by depressing the power window lock switch located on the dri-

· Do not extend face or arms outside through the window open-

ver's door to LOCK (pressed). · When the power window lock

ing while driving. · Always double check to make

switch is ON, the driver's master

sure all arms, hands and other

control cannot operate the passen-

obstructions are safely out of

ger door power windows either.

the way before closing a win-

dow.

3 15

Knowing your vehicle SEAT
1 2 3 4 5
· Type A
6 7 8 9
3 16

· Type B

Driver's seat (1) Seat adjustment, forward / back-
ward (2) Seatback recliner (3) Seat adjustment, height (4) Headrest adjustment
Front passenger seat (5) Seat adjustment, forward / back-
ward (6) Seatback recliner (7) Headrest adjustment
Rear seat (8) Split folding rear seat* (9) Headrest adjustment * : if equipped

1LDN2026

Knowing your vehicle

WARNING - Objects on

WARNING - Seating posi-

(Continued)

floor

tion

· Always drive and ride with

Loose objects in the driver's foot area could interfere with the operation of the foot pedals, possibly causing an accident. Do not place anything under the front seats.

· Never attempt to adjust seat while the vehicle is moving. This could result in loss of control, and an accident causing death or serious injury.
· Do not allow anything to inter-

your seatback upright and the lap portion of the safety belt,

is snug and low across the

hips. This puts your safety 2
belts in the best position to

protect you in case of an accident.

fere with the normal position of the seatback. Storing items against a seatback or in any other way interfering with proper locking of a seatback could result in serious or fatal injury in a sudden stop or collision.

· In order to avoid unnecessary airbag injuries including the possibility of severe injury or death, always sit as far back as possible from the steering wheel so that your chest is away at least 250 mm (10 inches) away from the steering

4 5 6

(Continued)

wheel.

3 17

Knowing your vehicle

Adjust the seat before driving, and

make sure the seat is locked secure-

ly by trying to move forward and

backward without using the lever. If

the seat moves, it is not locked prop-

erly.
2

1LDA2027

Driver's seat adjustment
5 Adjusting the seat forward and
backward

To move the seat forward or backward:

1. Pull the seat slide adjustment lever under the front edge of the

seat cushion up and hold it.

8 2. Slide the seat to the position you
desire.

3. Release the lever and make sure the seat is locked in place.

1LDA2028
Adjusting height of driver seat cushion (if equipped)
Pivoting the lever upward to raise the seat cushion.
Pivoting the lever downward to lower the seat cushion.

3 18

Knowing your vehicle

3. Release the lever and make sure the seatback is locked in place.

WARNING

(The lever MUST return to its orig- Driving or riding in a vehicle

inal position for the seatback to with a front seatback reclined 1

lock.)

could lead to serious or fatal

injury in an accident. If a front seat is reclined during an acci-

dent, the occupant's hips may

slide under the lap portion of the safety belt applying great

force to the unprotected

1LDA2029
Adjusting the driver's seatback recliner To recline the seatback:

abdomen. Serious or fatal inter- 4

nal injuries could result. The

driver must advise the front passenger to keep the seatbacks in

comfortably upright position

1. Lean forward slightly and lift up on the seatback recline lever located

whenever the vehicle is in motion.

on the outside of the seat, toward

the rear.

2. Carefully lean back on the seat

and adjust the back of the seat to the position you desire.

3 19

Knowing your vehicle

1LDA2033

1LDA2034

HNF2041-1

Headrest adjustment

Removal

Active headrest (if equipped)

5 Adjusting the height up and down

To remove the headrest, raise it as The active headrest is designed to

The headrest not only provides com- far as it can go then press the move forward and upward during a

fort for the driver and passengers, release button (1) while pulling rear impact. This helps to prevent the

but also helps to protect the head upward (2).

driver's and front passenger's head

and neck in the event of a collision.

from moving backward and thus

7 To raise the headrest, pull it up to the

WARNING

helps prevent neck injuries.

8 9

desired position (1). To lower the headrest, push and hold the release
button (2) on the headrest support and lower the headrest to the desired
position (3). For best protection, adjust the headrest so its center is as

To reduce the risk of head and neck injuries, do not drive the vehicle with the headrest removed or improperly positioned.

high as your ears.

Do not adjust the driver's head-

rest while driving.

3 20

Knowing your vehicle

Adjust the seat before driving, and

make sure the seat is locked secure-

ly by trying to move forward and

backward without using the lever. If

the seat moves, it is not locked prop-

erly.
2

WARNING
In order to avoid unnecessary

air bag injuries including the 1LDA2035 possibility of severe injury or

1LDA2036

Adjusting the front passenger death, always sit as far back as Adjusting seatback recliner

seat

possible by moving the seat far back, while still maintaining

To recline the seatback:

Forward/backward position

good vehicle control. Serious 1. Lean forward slightly and lift up on

adjustment To move the seat forward or back-

injury or death may be caused due to the deployment of the

the seatback recline lever located on the outside of the seat, toward

ward:

passenger's air bag.

the rear.

1. Pull the seat slide adjustment

2. Carefully lean back on the seat 7

lever under the front edge of the

and adjust the back of the seat to

seat cushion up and hold it. 2. Slide the seat to the position you

the position you desire. 3. Release the lever and make sure

desire.

the seatback is locked in place.

3. Release the lever and make sure the seat is locked in place.

(The lever MUST return to its orig- 9
inal position for the seatback to lock.)

3 21

Knowing your vehicle

WARNING - Driver

responsibility for front seat

passenger

Driving or riding in a vehicle

with a front seatback reclined could lead to serious or fatal

injury in an accident. If a front

seat is reclined, the occupant's hips may slide under the lap

portion of the safety belt apply-
4 ing great force to the unprotect-

1LDA2033A

1LDA2034A

ed abdomen. Serious or fatal Headrest adjustment

Removal

5 6

internal injuries could result. Keep the seatbacks in a comfortably upright position whenever the vehicle is in motion.

Adjusting the height up and down
The headrest not only provides comfort for the driver and passengers, but also helps to protect the head

To remove the headrest, raise it as far as it can go then press the release button (1) while pulling upward (2).

and neck in the event of a collision.

To raise the headrest, pull it up to the desired position (1). To lower the

WARNING

headrest, push and hold the release button (2) on the headrest support

To reduce the risk of head and neck injuries, do not drive the

and lower the headrest to the desired vehicle with the headrest

position (3). For best protection, adjust the headrest so its center is as

removed or improperly positioned.

high as your ears.

3 22

Knowing your vehicle

Rear seat

Split folding rear seat

(if equipped) The rear seatbacks fold forward to

provide additional cargo space and

to provide access to the cargo area.

· To fold the rear seatback(s) down, pull the lock release lever, then fold the seatback forward and down.

1LDN2038

HNF2041-1
Active headrest (if equipped)
The active headrest is designed to move forward and upward during a rear impact. This helps to prevent the driver's and front passenger's head from moving backward and thus helps prevent neck injuries.

· To raise the seatback, lift and push it firmly until it clicks into place.
· When you return the seatback to its upright position, reposition the rear safety belts so that they can be used by rear seat passengers.

4 Door (if equipped)

4
5
6
1LDN3025
7

1. Pull the lock release lever.

2. Move the rear three-point seat 8
belts to the outside (1) so that they

don't interfere with the seatback

when lowering.

3. Fold the seatback forward and

down firmly (2).

3 23

Knowing your vehicle

Type A

Type B

1LDA2239/1LDA2239A

1LDA2241

1LDA2243

1LDA2240

1LDA2242

1LDA2244

7 5 Door (if equipped)

3 Move the seat cushion firmly until it 5. Pull the lock release lever (5).

1. Lift the front of seat cushion (1) up. clicks (3).

6. Fold the seatback forward and

2. Lift the rear of seat cushion up (2). 4. Remove the headrest and put the headrest poles into the holes on

down firmly (6).

the rear of the seat cushion (4).
9

3 24

Knowing your vehicle

NOTICE

If the seat belt is locked during the

seatback folding, pull out and retract the seat belt to release it.

CAUTION

1LDN3026B

· When returning the rear seat-

backs to the upright position, remember to return the rear

shoulder belts to their proper

1LDN3026A

position.

NOTICE

To unfold the rear seat:

· Do not remove the floor carpet

When you fold the rear seatback or put luggage on the rear seat cushion, insert the buckle in the pocket between the rear seatback and cush-

1. Move the rear center shoulder belt (1) to the side so that it is clear of the seatback.
2. Lift and push the seatback back-

in your vehicle. Emission control system components

cause high exhaust tempera-

tures under the floor.

ion. Doing so can prevent the buckle

ward firmly until it clicks into place

from being damaged by the rear seatback or luggage.

(2). Move and push the seat cushion

WARNING - Cargo danger

downward firmly to the proper Cargo should always be

position (5 Door, if equipped).

secured to prevent it from shift-

3. Replace the rear safty belt to the ing and causing injury to the

proper position.

vehicle occupants.

3 25

Knowing your vehicle

CAUTION - Loading pro-

cedure

1 Make sure the engine is off, the

transaxle is in P and the parking

brake is applied whenever loading or unloading cargo. Vehicle

may move if shift lever is inad-

vertently moved to another position.

1LDA2042

1LDA2043

Headrest adjustment

Removal

Adjusting the height up and down

To remove the headrest, raise it as

The headrest not only provides com- far as it can go then press the

fort for the driver and passengers, release button (1) while pulling but also helps to protect the head upward (2).

and neck in the event of a collision.

To raise the headrest, pull it up to the

WARNING

desired position (1). To lower the To reduce the risk of head and

headrest, push and hold the release neck injuries, do not drive the button (2) on the headrest support vehicle with the headrest

and lower the headrest to the desired removed or improperly posi-

position (3). For best protection, tioned. adjust the headrest so its center is as

high as your ears.

3 26

Knowing your vehicle

SAFETY BELTS

The pre-tensioner seat belt is

installed at the front seats, and the

sensor is equipped inside the buckle,

where presence of passenger is

sensed by the fastening of the seat

belts. Therefore, pre-tensioner will

not activate if the passenger is not

fastened with the seat belts.

Likewise, it will activate if buckled

even without a passenger in the

seat. Pre-tensioner seat belt is

3
3

2GHB3002 designed to activate when the seatbelt is in use. To ensure the preten-

2GHB3001

Pre-tensioner seat belt

sioner seatbelts activate in event of a The seat belt pre-tensioner system

Your vehicle is equipped with driver's and front passenger's pre-tensioner seat belts. The purpose of the pretensioner is to make sure that the

possible seatbelt buckle switch malfunction, the system is designed to activate regardless of whether a seat belt is in use or if no seat belt use is

consists mainly of the following components. Their locations are shown in the illustration.
(1) SRS airbag warning light

5 6

seat belts fit tightly against the occu- detected within 6 seconds of turning (2) Seatbelt pre-tensioner assembly

pant's body in certain frontal colli- the ignition switch ON. sions. The pre-tensioner seat belts

(3) SRS airbag control module

can be activated together with the air

bags, where the frontal collision is

severe enough.

3 27

Knowing your vehicle

WARNING

CAUTION

To obtain maximum benefit from When the pre-tensioner seat · Because the sensor that acti-

1 a pre-tensioner seat belt:

belts are activated, a loud noise

vates the SRS air bag is con-

· The seat belt must be worn correctly.

may be heard and fine dust, which may appear to be smoke, may be visible in the passenger

nected with pre-tensioner seat belt, the SRS air bag warning light on the instrument panel

· The seat belt must be adjusted compartment and are not toxic.

will blink or illuminate for

to the correct position.

Although, it is harmless, the fine dust may cause skin irritation

approximately 6 seconds after the ignition key has been

and should not be breathed for

turned to the "ON" position,

prolonged periods. Wash your

then the light should go off.

hands and face thoroughly after · If the pre-tensioner seat belt is

an accident in which the air bags and/or pre-tensioner seat

not working properly, this warning light will illuminate

belts were activated.

even if there is no malfunction

of SRS air bag system. If the SRS air bag warning light

does not illuminate when the

ignition key is turned to "ON",

or if it remains illuminated

after blinking or illuminating for approximately 6 seconds,

or if it illuminates while the

vehicle is being driven, please have an authorized Kia dealer

inspect the pre-tensioner seat

belt or SRS air bag system as

soon as possible.

3 28

Knowing your vehicle

CAUTION

WARNING

The pre-tensioner seat belt · Pre-tensioners are designed · Do not strike the pre-tensioner

assembly mechanisms become

to operate once. After activa-

seat belt assemblies.

hot during activation. Do not touch the pre-tensioner seat belt assembly for several minutes after they have been activated.

tion, pre-tensioner seat belts · Do not attempt to service or

must be replaced. All seat belts, of any type, should

repair the pre-tensioner seat belt system in any manner.

always be replaced after they have been worn during a collision.

· Improper handling of the pretensioner seat belt assemblies, and failure to heed the

· Do not attempt to inspect or replace the pre-tensioner seat

warnings not to strike, modify, inspect, place, service or

belts yourself. This must be

repair the pre-tensioner seat

done by an authorized Kia dealer.

belt assemblies may lead to improper operation or inad-

vertent activation causing

serious injury.

Always wear the seat belts

when driving or riding in a motor vehicle.

3 29

Knowing your vehicle

Safety belt restraint system

We strongly recommend that the Since the inertial locks do not require

driver and all passengers be proper- a collision in order to lock up, you

WARNING - Safety belts

ly restrained at all times by using the may become aware of the safety

1 2 3

To minimize the risk of serious or fatal injury in an accident, the driver and all passengers should use the appropriate safety restraints for their age and size. The presence of air

safety belts provided with the vehicle. Proper use of the safety belts decreases the risk of severe injury or death in accidents or sudden stops. In most states, and in Canada, the law requires their use.

belts locking while braking or going around sharp corners.
Always use the rear seat position(s) to install your child restraint(s).
Never install a child restraint system in the front passenger position, as an

bags does not change the need

inflating air bag could cause serious

to be properly restrained by a All seats have lap/shoulder belts. or fatal injury to a child in that posisafety belt or size-appropriate Inertial locks in the safety belt retrac- tion.

child restraint. In fact, air bags tors allow all of the lap/shoulder safe-

are designed to work the best ty belts to remain unlocked during when passengers are correctly normal vehicle operation. This allows

restrained in the vehicle. Be the occupants some freedom of

sure you are familiar with the movement and increased comfort information in this section, while using the safety belts. If a force

including the information on is applied to the vehicle, such as a infant and child restraints. Read strong stop, a sharp turn, or a colli-

the safety warnings on the sun sion, the safety belt retractors will

visors of your vehicle also.

automatically lock the safety belts.

3 30

Knowing your vehicle

The rear safety belts use a special auto-lock feature designed to allow a child restraint to be used in these positions without an added locking clip. They normally lock only under extreme or emergency conditions (emergency lock mode). However they can be adjusted so that they remain in fixed and locked when a child restraint system is placed in these positions. (Use this auto-lock mode only to secure a child restraint, never for passengers restrained by the safety belts.) Page 3-44 gives instructions on placing the safety belt in the auto lock mode.
The drivers safety belt can only operate in the emergency lock mode.

Safety belts provide the best restraint when:
· The seatback is upright.
· The occupant is sitting upright (not slouched).
· The lap belt is snug across the hips.
· The shoulder belt is snug across the chest.
· The knees are straight forward.
To help you remember to fasten your safety belt, a warning light will come on and a chime will sound. See Safety Belt Warning Light and Chime on page 3-33.
WARNING - After a colli-
sion
· Lap/shoulder belt assemblies may be stretched or damaged when subjected to the stress and forces of a collision.
· The entire restraint system should be inspected following any collision. All belts, retractors, anchors and hardware damaged by a collision should be replaced before the vehicle is operated again.

WARNING - Cargo area

(if equipped)

Passengers should never be 1

allowed to ride in the cargo area

of a vehicle. No safety belts are provided for the cargo area.

Persons riding in the vehicle

without a fastened safety belt are much more likely to suffer

serious bodily injury or death

during an accident.

WARNING - Twisted belts

A twisted or jammed safety belt cannot restrain you properly. If

you cannot untwist or unjam the

safety belt, have an authorized Kia dealer it immediately. Never

drive or ride with a twisted or

jammed safety belt.

3 31

Knowing your vehicle

WARNING - Belt use

Safety belts must be used cor-
1 rectly to work properly in an

accident. Each seating position

in your vehicle has a specific safety belt assembly that

includes a buckle and tongue

3 designed to be used together.
For greatest effectiveness, fol-

low these guidelines in using safety belts:

· Use the shoulder portion of

the safety belt on the outside shoulder only. Never wear the

shoulder portion under the

arm.

· Never swing the safety belt

around your neck to fit over the inside shoulder.

· Never wear the shoulder portion of the safety belt across

the neck or face.

(Continued)

3 32

(Continued)
· Wear the lap portion as low as possible. Be sure that the lap belt fits snugly around the hips. Never wear a lap portion of a lap/shoulder belt over your waist; it should always go over the stronger area of your hips.
· Never use a single safety belt for more than one person.
· The front seatbacks should always remain in a comfortable, upright position when the vehicle is moving.
WARNING - Safety belt
care
· A damaged belt may not give you the protection you need in an accident.
(Continued)

(Continued)
· Inspect your safety belts periodically for excessive wear or damage. Pull out each belt fully and look for fraying, cuts, burns or other damage. Pull the safety belt out and let it retract a number of times. Make sure that the lap/shoulder belts return smoothly and easily into the retractor.
· Check the latches to make sure they latch and release without interference or delay.
· Never close the doors on any part of the lap or shoulder belt.
· Any belt not in good condition or in good working order should be promptly replaced.
CAUTION
Never close the doors on any part of the lap or shoulder belt. It can damage the safety belt or buckle which could increase the risk of injury in case of an accident.

Knowing your vehicle

If the lap/shoulder belt is unfastened

while the lap/shoulder belt is fas-

tened with the ignition switch ON, the

safety belt warning light will blink for

about 6 seconds and if the vehicle

speed exceeds 10 km/h (6 mph) the

safety belt warning light and chime

will activate until it is fastened.

1GQA2083
Safety belt warning light and chime
If the driver's lap/shoulder belt is not fastened when the ignition switch is turned ON, the safety belt warning light and chime will activate for about 6 seconds. And if the lap/shoulder belt is fastened when the ignition switch is turned ON, the safety belt warning light will blink for about 6 seconds.

B180A01NF-1

Lap/shoulder belt

To fasten the lap/shoulder belt:

1. Grasp the buckle and tongue

plate.

2. Slowly pull the lap/shoulder belt

out from the retractor. 3. Insert the tongue plate (1) into the

open end of the buckle (2) until an

audible "click" is heard, indicating 8
the belt is locked in the buckle.

3 33

Knowing your vehicle

WARNING - Beld adjust

· The height adjuster must be in

the locked position when the

vehicle is moving.

· The misadjustment of height of the shoulder belt could

reduce the effectiveness of

the seat belt in a crash.

B200A02NF

OUN026100

4. Position the lap portion of the belt 5. Adjust the shoulder anchor posi-

across your lap as LOW ON THE HIPS as possible to reduce the

tion to your size. To raise the anchor position, push the anchor

risk of sliding under it during an up (1). To lower the anchor posi-

accident. Adjust the belt to a tion, press (2) the button and slide

SNUG FIT by pulling up on the the anchor down (3). After adjust-

shoulder portion of the safety belt. The belt retractor is designed to

ment, make sure the anchor is locked in position.

take up excess webbing automati- If the height of the adjusting seat belt

cally and to maintain tension on is too near your neck, you will not be the belt. For your safety, do not put getting the most effective protection.

any excess slack into the safety The shoulder portion should be

belt at any location.

adjusted so that it lies across your

chest and midway over your shoulder

nearest the door and not your neck.

3 34

Knowing your vehicle

B210A01NF

1LDN2045

1LDN3207

To unfasten the lap/shoulder belt: When using the rear center seat belt, 3 Point rear center belt

Press the release button on the the buckle with the "CENTER" mark (if equipped)

buckle and allow the belt to slowly must be used.

To fasten the rear center belt

retract.

1. Extract the tongue plates from the holes on the belt assembly cover

and slowly pull the tongue plates

out from the retractor.

3 35

Knowing your vehicle

There will be an audible "click" when

the tab locks in the buckle. The seat

belt automatically adjusts to the

proper length only after the lap belt is

adjusted manually so that it fits snug-

ly around your hips, if you lean for-

ward in a slow, easy motion, the belt

will extend and let you move around.

If there is a sudden stop or impact, the belt will lock into position. It will

also lock if you try to lean forward too

1LDN3208A

1LDN3209 quickly.

2. Insert the tongue plate (A) into the 3. Pull the tongue plate (B) and

open end of the buckle (C) until an audible "click" is heard, indicating

insert the tongue plate into the open end of the buckle (D) until an

WARNING

the latch is locked. Make sure the

audible "click" is heard, indicating When using the rear seat center

belt is not twisted.

the latch is locked. Make sure the belt, you must lock all tongue

belt is not twisted.

plates and buckle/anchor con-

nector. If any tongue plate or

buckle/anchor connector is not

locked, it will increase the

chance of injury or death in the event of collision.

3 36

Knowing your vehicle

1LDN3210

1LDN3211A

1LDN3215

To unfasten the rear center belt

2. To retract the rear center seatbelt, 3. Insert the tongue plates into the

1. Press the release button on the buckle (D) and remove the tongue plate (B) from the buckle (D).

insert the key or similar small rigid device into the web release button (C) on the anchor connector. Pull up on the seat belt web (A) and allow the webbing to retract auto-

holes and hang the tongue plates on the hooks on the belt assembly

cover.

matically. (5 Door, if equipped)

3 37

Knowing your vehicle

Proper use and care of the

· To clean the belt webbing, use a Restraint of pregnant women

safety belt system

To ensure that the safety belts provide the maximum protection, please

follow these instructions:

mild soap solution recommended for cleaning upholstery or carpets. Follow the instructions provided with the soap.

Pregnant women should wear lap/shoulder belt assemblies whenever possible according to specific recommendations by their doctors.

2 3 4

· Use the belts at all times - even on short trips.
· If the safety belt is twisted, straighten it prior to use.
· Keep sharp edges and damaging objects away from the belts.

· Do not make modifications or additions to the safety belt.
· After wearing a safety belt, make sure it fully retracts to the stowed position. Do not allow the belt to get caught in the door when you close it.

The lap portion of the belt should be worn AS SNUGLY AND LOW AS POSSIBLE.
WARNING - Pregnant
women

· Periodically inspect belt webbing,

5 6

anchors, buckles and all other parts for signs of wear and damage. Replace damaged, excessively worn or questionable parts immediately.

WARNING
Do not bleach or dye the webbing because this may weaken the webbing fibers and allow them to fail when loaded in a

Pregnant women must never place the lap portion of the safety belt over the area of the abdomen where the fetus is located or above the abdomen where the belt could injure the fetus during an impact.

collision.

3 38

Knowing your vehicle

Restraint of infants and small children

Many companies manufacture child restraint systems (often called child

WARNING - Infants and

To increase their safety, infants and young children should always be restrained by a restraint system approved for their age and size.
Never allow a child to stand or kneel on the seat of a moving vehicle. Never allow a safety belt to be placed around both a child and an adult or around two children at the same time.

seats) for infants and small children. An acceptable child restraint system must always satisfy the Safety Standards of your country. Make sure that any child-restraint system you use in your vehicle is labelled as complying with those safety standards.
The child-restraint system should be chosen to fit both the size of the child and the size of the vehicle seat. Be

young children
· Infants and young children are at much greater risk of serious injury or death in an accident or sudden stop if they are unrestrained or restrained improperly. Follow all instructions in this section of your Kia manual and the instructions that came on and with an improved child safety restraint system. The

1 2 3 4

It is best for children to be seated in sure to follow any instructions provid-

the rear seats.

ed by the child-restraint system man-

child restraint must be correctly installed in the vehicle, and

ufacturer when installing the child-

the child must be correctly

WARNING - Children on
laps

restraint system.

installed in the child restraint.

· All children under 12 are

Never hold a child on your lap or in your arms in a moving vehi-

safest in the back seat.
· Never install a child or infant 7

cle.

seat in the front passenger

Even a very strong person cannot hold onto a child in the

position. The baby will be injured or killed by the air bag

event of even a minor collision.

if it deploys in an accident.
· Never allow a child to stand or 9

kneel on the seat of a moving

vehicle. Insist the child sit down

in an approved restraint system.

3 39

Knowing your vehicle

Restraint of larger children

WARNING - Hot metal
parts
Safety belts and seats can

As children grow, they may need to use new child-restraint systems, including larger child seats or boost-

WARNING - Shoulder
belts on small children
· Never allow a shoulder belt to

become hot in a vehicle that has er seats, which are appropriate for

be in contact with a child's

2 3

been closed during warm/hot weather; they could burn a child. Check seat covers and buckles before you place a child anywhere near them.

their increased size.
A child who has outgrown available child-restraint systems should use the belts provided in the vehicle. When seated in the rear outboard

neck or face while the vehicle is in motion.
· If safety belts are not properly worn and adjusted, there is a risk of death or serious injury

seats, the child should be restrained by the lap/shoulder belt.

to such a child.

If the shoulder belt portion slightly

touches the child's neck or face, try

placing the child closer to the center

of the vehicle. If the shoulder belt still touches their face or neck they may

need to be returned to a child

restraint system. In addition, aftermarket devices are available from

independent manufacturers which

help pull the shoulder belt down and

away from the child's face or neck.

Larger children should use one of the seat belts provided.

3 40

Knowing your vehicle

Child restraint system

You are required by law to use safe-

(if equipped)

ty restraints for children. If small chil-

For small children and babies, the use of a child seat or infant seat is required by law. This child seat or

dren ride in your vehicle you must put them in a child restraint system (safety seat).

infant seat should be of appropriate Children could be injured or killed in size for the child and should be a crash if their restraints are not

installed in accordance with the man- properly secured. For small children

ufacturer's instructions. It is strongly and babies, a child seat or infant seat recommended that the seat be must be used. Before buying a par-

placed in the vehicle's rear seat ticular child restraint system, make since this can make an important sure it fits your car and seat belts,

ADAIR BAG

contribution to safety.

and fits your child. Follow all the

Children riding in the car should sit on the rear seat and must always be properly restrained to minimize the

instructions provided by the manufacturer when installing the child restraint system.

WARNING
· A child restraint system must

risk of injury in an accident, sudden

be placed in the rear seat. 6

stop or sudden maneuver. According

Never install a child or infant

to accident statistics, children are safer when properly restrained in the

seat on the front passenger's seat.

rear seats than in the front seat.

Should an accident occur and

cause the passenger air bag 8
to deploy, it could severely

injure or kill an infant or child seated in an infant or child

seat. Thus, only use a child

restraint in the rear seat of

your vehicle.

(Continued)

3 41

Knowing your vehicle

(Continued)

· Since a safety belt or child · Always make sure that the · Never allow a child to stand up

restraint system can become very hot if it is left in a closed

shoulder belt portion of the lap/shoulder belt is positioned

or kneel on the seat. · Never use an infant carrier or

vehicle, be sure to check the

midway over the shoulder,

child seat that "hooks" over a

seat cover and buckles before

never across the neck or

seatback. It will not provide

placing a child there.

behind the back. The lap belt

adequate protection in an

· When the child restraint system is not in use, store it in the

trunk or fasten it with a safety

belt so that it will not be thrown forward in the case of

portion of the lap/shoulder belt must always be positioned as low as possible on the child's hips and as snug as possible.

accident.
· Never allow a child to be held while they are in a moving vehicle, as this could result in serious injury or death to the

a sudden stop or an accident. · If the seat belt will not proper-

5 · Children who are too large to

ly fit the child the use of an

child in the event of an accident or sudden stop. Holding

be in a child restraint should

approved booster seat in the

a child in a moving vehicle

sit in the rear seat and be restrained with the available

rear seat must be used in order to raise the child's seat-

does not provide the child with any protection during an

lap/shoulder belts. Never

ing height so that the seat belt

accident, even if the person

allow children to ride in the

will properly fit the child.

holding the child is wearing a

front passenger seat.

(Continued)

seat belt.

(Continued)

3 42

Knowing your vehicle

Installing a child restraint system For safety reasons, we recommend

WARNING

that the child restraint system be · Before installing the child · Do not install any child

used in the rear seats. Never place

restraint system, read the

restraint system in the front 1

a rear-facing child restraint in the

instructions supplied by the

passenger seat. Should an

front passenger seat, because of the danger that an inflating pas-

child restraint system manufacturer.

accident occur and cause the passenger air bag to deploy, it

senger side air bag could impact · If the seat belt does not oper-

could severely injure or kill an

the rear-facing child restraint and kill the child.

ate as described, have the system checked immediately

infant or child seated in an infant or child seat. Therefore,

Since all passenger's (except driver's) safety belts move freely under normal conditions and only lock

by your authorized Kia dealer.
· Failure to observe this manual instructions regarding child

only use a child restraint sys-
tem in the rear seat of your 4
vehicle.

under extreme or emergency conditions (emergency lock mode), you

restraint system and the instructions provided with the

· If the child restraint seat is not anchored properly, the risk of

must manually change these safety

child restraint system could

a child being seriously injured

belts to the auto lock mode to secure a child restraint.

increase the chance and/or severity of injury in an acci-

or killed in a collision greatly increases.

NOTICE

dent.

The driver's safety belt incorporates

the emergency lock mode only.

3 43

Knowing your vehicle

Placing a passenger safety belt into the auto lock mode

The use of the auto lock mode will ensure that the normal movement of

the child in the vehicle does not

cause the safety belt to be pulled out and loosen the firmness of its hold

on the child restraint system. To

3 secure a child restraint system, use

the following procedure.

E2MS103005

E2BLD310

Installing a child restraint system by 2. Fasten the lap/shoulder belt latch

lap/shoulder belt To install a child restraint system on

into the buckle. Listen for the distinct "click" sound.

the outboard or center rear seats, do Position the release button so that it

the following:

is easy to access in case of an

1. Place the child restraint system in emergency.

the seat and route the lap/shoul-

der belt around or through the

restraint, following the restraint manufacturer's instructions. Be

sure the safety belt webbing is not

twisted.

3 44

Knowing your vehicle

"Click"

MMSA3028

MMSA3029

MMSA3030

3. Pull the shoulder portion of the 4. Slowly allow the shoulder portion 5. Remove as much slack from the

safety belt all the way out. When the shoulder portion of the safety

of the safety belt to retract and listen for an audible "clicking" or

belt as possible by pushing down on the child restraint system while

belt is fully extended, it will shift "ratcheting" sound. This indicates feeding the shoulder belt back into

the retractor to the "Auto Lock" (child restraint) mode.

that the retractor is in the "Auto the retractor.

Lock" mode. If no distinct sound is 6. Push and pull on the child restraint

heard, repeat steps 3 and 4.

system to confirm that the safety belt is holding it firmly in place. If it

is not, release the safety belt and

repeat steps 2 through 6.

3 45

Knowing your vehicle

7. Double check that the retractor is in the "Auto Lock" mode by

WARNING - Auto lock

attempting to pull more of the safe-

mode

ty belt out of the retractor. If you The lap/shoulder belt automati-

cannot, the retractor is in the "Auto cally returns to the "emergency

Lock" mode. To remove the child restraint, press

lock mode" whenever the belt is allowed to retract fully.

the release button on the buckle and Therefore, the preceding seven

then pull the lap/shoulder belt out of the restraint and allow the safety belt

steps must be followed each time a child restraint is

to retract fully.

installed.

If the safety belt is not placed in

the "auto lock" mode, severe

injury or death could occur to the child and/or other occupants

in the vehicle in a collision,

since the child restraint will not

be effectively held in place.

4 Door 5 Door

1LDN3200/1LDN3200A

NOTICE

Securing a child restraint seat

When the safety belt is allowed to with "Tether Anchor" system retract to its fully stowed position, Child restraint hook holders are

the retractor will automatically located on the shelf or floor behind

switch from the "Auto Lock" mode to the emergency lock mode for normal adult usage.

the rear seats.
1. Open the tether anchor cover on the shelf or floor behind the rear

seats.

3 46

Knowing your vehicle

WARNING

If the tether strap is secured

- Child restraint anchorage

incorrectly, the child restraint

· Child restraint anchorages are

seat may not be restrained

designed to withstand only

properly in the event of a collision.

those loads imposed by correctly fitted child restraints.

Under no circumstances are

WARNING - Child

they to be used for adult seat belts or harnesses or for

attaching other items or

2GHN3300A

restraint

equipment to the vehicle.

2. Route the child restraint seat strap over the seatback.
For vehicles with adjustable headrest, route the tether strap under the headrest and between the

Check that the child restraint system is secure by pushing and pulling it in different directions. Incorrectly fitted child restraints may swing, twist, tip or come away causing death or

· The tether strap may not work properly if attached somewhere other than the correct tether anchor.

5 6

headrest posts, otherwise route injury.

the tether strap over the top of the seatback.

3. Connect the tether strap hook to

the correct child restraint hook

holder and tighten to secure the

seat.

3 47

Knowing your vehicle

Label

WARNING

When using the vehicle's

"ISOFIX" system to install a

child restraint system in the rear

seat, all unused vehicle rear seat belt metal latch plates or

tabs must be latched securely in

their seat belt buckles and the seat belt webbing must be

Child lower anchor

retracted behind the child

1LDN3050

1LDN3100/1LDN3100A restraint to prevent the child

5 6

Child seat lower anchors
Some child seat manufacturers make child restraint seats that are labeled as International Standards Organization Fixed (ISOFIX) or

There is a symbol located on the lower portion of each side of the rear seatbacks. These symbols indicate the position of the lower anchors for child restraints so equipped.

from reaching and taking hold of unretracted seat belts. Unlatched metal latch plates or tabs may allow the child to reach the unretracted seat belts which may result in strangula-

ISOFIX-compatible child restraint

tion and a serious injury or

seats. These seats include two rigid or webbing mounted attachments

death to the child in the child restraint.

that connect to two ISOFIX anchors

8 at specific seating positions in your
vehicle. This type of child restraint

seat eliminates the need to use seat
9 belts to attach the child seat in the

rear seats.

3 48

Knowing your vehicle

Once you have installed the ISOFIX child restraint, assure that the seat is

(Continued)

properly attached to the ISOFIX and · Do not install a child restraint

tether anchors. Also, test the child restraint seat before you place the

seat at the rear center seating position using the vehicle's

child in it. Tilt the seat from side to side. Also try to tug the seat forward. Check to see if the anchors hold the

ISOFIX anchors. The ISOFIX
anchors are only provided for 2
the left and right outboard rear

seat in place.

seating positions. Do not misuse the ISOFIX anchors by

WARNING

attempting to attach a child

1LDN3100/SBGQ03102
ISOFIX anchors have been provided in your vehicle. The ISOFIX anchors are located in the left and right outboard rear seating positions. Their

If the child restraint is not anchored properly, the risk of a child being seriously injured or killed in a collision greatly increases.

restraint seat in the middle rear seating position to the

ISOFIX anchors. In a crash,

the child restraint seat ISOFIX attachments may not be

strong enough to secure the

locations are shown in the illustration. There is no ISOFIX anchor provided for the center rear seating position.

WARNING
· Do not mount more than one

child restraint seat improperly 6

in the rear center seating posi-

tion and may break, causing serious injury or death.

The ISOFIX anchors are located between the seatback and the seat cushion of the rear seat left and right outboard seating positions. Follow the child seat manufacturer's instructions to properly install child restraint seats with ISOFIX or ISOFIX-compatible attachments.

child restraint to a single teth- · Attach the ISOFIX or ISOFIX-

er or to a child restraint lower

compatible child restraint seat 8

anchorage point. The improp-

only to the appropriate loca-

er increased load may cause the anchorage points or tether anchor to break, causing serious injury or death.

tions shown in the illustration.
· Always follow the installation and use instructions provided by the manufacturer of the

(Continued)

child restraint.

3 49

Knowing your vehicle

AIR BAG - ADVANCED SUPPLEMENTAL RESTRAINT SYSTEM

(1) Driver's air bag (2) Front passenger's air bag (3) Side air bag* (4) Curtain air bag* (5) SRS Control Module (6) Side impact sensor* (7) Front impact sensor (8) Front seat position sensor (9) Occupant classification system * : if equipped

1JBN3511A/OMGA035047/OMGA035048/OMGA035049/OMGA035051/OMGA035052/OMGA035053/OMGA035055/OMGA035054/1LDN2166/1LDN2167/1LDN2168
3 50

Knowing your vehicle

What your air bag system does

What your air bag system does not do

The importance of using safety belts

Driver's air bag and front passen- The air bag system is designed to There are four very important reager's air bag are designed to supple- supplement the protection offered by sons to use safety belts even with an

ment the protection offered by the the safety belt system. IT IS NOT A air bag supplemental restraint sys-

safety belt in certain frontal colli- SUBSTITUTE FOR THE SAFETY tem. They:

sions. Likewise, side air bag and cur- BELT.

· help keep you in the proper posi-

tain air bags are designed to supplement the protection offered by the

tion (away from the air bag) when it inflates.

safety belt in side collisions. Safety belts are designed to reduce the injury of the driver or passengers in case of impact or collision. No safety belt or air bag system can completely eliminate injuries that may cause in collisions or impacts. To help reduce impact on driver or passengers in any collision, safety belts must be correctly worn.

· reduce the risk of harm in rollover,

side impact (vehicles not equipped 4
with side and curtain air bags) or

rear impact collisions, because an
air bag is not designed to inflate in 5

such situations and even a side

curtain air bag is designed to inflate only in certain side impact

collisions.

· reduce the risk of harm in frontal or 7

side collisions which are not

severe enough to actuate the air bag supplemental restraint system.

· reduce the risk of being ejected

from your vehicle.

3 51

Knowing your vehicle

WARNING - Air bags &

(Continued)

safety belts

· Driver's and front passenger's · If your vehicle has been sub-

1 · Even in vehicles with air bags,

you and your passengers

must always wear the safety belts provided in order to min-

imize the risk and severity of

injury in the event of a collision or rollover.

air bag are designed to inflate only in certain frontal collisions, and side and curtain air bags (if equipped) are designed to inflate in certain side impacts. Frontal air bag will generally not provide protection in side impacts (vehi-

jected to flood conditions (e.g. soaked carpeting/standing water on the floor of the vehicle, etc.) or if your vehicle has become flood damaged in any way, do not attempt to start the vehicle or put the key in the ignition before discon-

· Always wear your safety belt. It can help keep you away

from the air bags during heavy

braking just before a collision. It may also reduce the risk of

occupant ejection.

6 · If occupants are not wearing

cles not equipped with side and curtain air bags) or rear impacts, rollovers, less severe frontal collisions. They will not provide protection from later impacts in a multi-impact collision.

necting the battery.
Disregarding this precaution may cause air bag deployment, which could result in serious personal injury or death. If your vehicle is subjected to flooded conditions,

safety belts or correctly seat-

(Continued)

before starting the vehicle,

ed, they cannot be protected, and thus face serious injury or

have the vehicle towed to an authorized Kia dealer for

death.

inspection and necessary

(Continued)

repairs.

3 52

Knowing your vehicle

Air bag system components

The SRS uses a collection of sen- The advanced SRS offers the ability

The main components of your SRS are:
· To indicate that your vehicle is

sors to gather information about the driver's and front passenger's seat position, the driver's and front passenger's safety belt usage and

to control the air bag inflation with two levels. A first stage level is provided for moderate-severity impacts. A second stage level is provided for

equipped with air bags, the corre- impact severity.

more severe impacts.

sponding air bag covers are marked with "SRS AIR BAG".

The driver's and front passenger's seat position sensors, which are

The SRSCM (SRS Control Module) controls the air bag inflation in accor-

- Driver's air bag - Passenger's air bag

installed on the seat track, determine dance with impact severity, seating if the seats are fore or aft of a refer- position and safety belt usage.

- Side air bag
- Curtain air bag
· A diagnostic system that continually monitors the system operation.

ence position. Similarly, the safety belt usage sensors determine if the driver and front passenger's safety belts are fastened. These sensors provide the ability to control the SRS

Additionally, your SRS is equipped with an occupant classification system in the front passenger's seat. The occupant classification system detects the presence of a passenger

4 5

· An indicator light to warn you of a deployment based on how close the in the front passenger's seat and will

possible problem with the system.
· Emergency power backup in case your car's electrical system is disconnected in a crash.

driver's seat is to the steering wheel, how close the passenger's seat is to the instrument panel, whether or not the safety belts are fastened, and how severe is the impact.

turn off the front passenger's air bag under certain conditions. For more detail, see "Occupant Classification System" later in this section.

6 7

3 53

Knowing your vehicle

CAUTION

WARNING

(Continued)

1 2 3 4 5

If the seat position sensor is not working properly, the SRS air bag warning light ( ) on the instrument panel will illuminate even if there is no malfunction of the SRS air bag system, because the SRS air bag warning light is connected with the seat position sensor. If the SRS air bag warning light does not illuminate when the ignition key is turned to the "ON" position, if it remains illuminated after blinking for approximately 6

· Modification to the seat structure can adversely affect the seat position sensor and cause the air bag to deploy at a different level than should be provided.
· Failure to properly wear safety belts can increase the risk or severity of injury by causing the air bags to deploy at a different level than should be provided.
· Do not place any objects

· Ignoring the SRS indicator light (air bag indicator and passenger air bag off indicator) can result in serious or fatal injury if the air bags occupant classification system or pretensioners do not work properly. Have your car checked by a dealer as soon as possible if the SRS warning light alerts you to a potential problem.
· Sitting improperly or out of position can result in serious

seconds, or if it illuminates while the vehicle is being driv-

underneath the front seats which could damage the seat

or fatal injury in a crash. All occupants should sit upright

en, have an authorized Kia deal-

position sensor or interfere

in their seats with their feet on

er inspect the seat position sensor and the advanced SRS air

with the occupant classification system.

the floor until the vehicle is parked and the ignition key is

bag system as soon as possi- · Do not place any objects that

removed.

8 ble.

may cause magnetic fields

near the front seat. These may

cause a malfunction of the seat position sensor.

(Continued)

3 54

Knowing your vehicle

OLD026048
HLZ2120
Driver's air bag The driver's air bag is stored in the center of the steering wheel.

WARNING
· You must always sit as far back from the steering wheel air bag as possible (chest at least 250 mm (10 inches) away from the steering wheel), while still maintaining a comfortable seating position for good vehicle control, in order to reduce the risk of injury or death in a collision.
· Never place objects over the air bag storage compartments or between the air bags and yourself. Due to the speed and force of the air bag inflation, such objects could hit your body at high speed and cause severe bodily injury and even death.
· Do not put stickers or ornaments on the steering wheel cover. These may interfere with the deployment of the air bag.

3
1LDA2049
4

HLZ2121

Front passenger's air bag

Front passenger's air bag is stored in

the instrument panel on the glove box.

Since you cannot anticipate which air bags will deploy or from what direction, never put any objects or ornaments on the instrument panel.

3 55

Knowing your vehicle

Main components of occupant classification system

The location of OCS Indicator

· A detection device located within

the front passenger seat cushion.

· Electronic system to determine

whether passenger air bag system should be activated or deactivated.

· A indicator light located on the instrument panel which illuminates

the words "PASSENGER AIR BAG

1LDN2166

OFF" indicating the frontal passenger air bag system is deactivated.

OLD036150N

5 6

Occupant classification system
The occupant classification system detects the presence of a passenger in the front passenger's seat and will turn off the front passenger's air bag

· The instrument panel air bag warning light is interconnected with the occupant classification system.

If there is no passenger in the front passenger seat or if the passenger in the front passenger seat is very light, (such as a child), the front PASSENGER AIR BAG OFF indicator may

under certain conditions.

illuminate.

7 The occupant classification system is
designed to detect the presence of a properly-seated occupant and deter-
8 mine if the front passenger's air bag

When this indicator is ON, the front passenger front air bag will not deploy.

should be enabled (may inflate) or

not. Only the front passenger air bag is

controlled by the Occupant

Classification System.

3 56

Knowing your vehicle

Always be sure that you and all vehi- · The "PASSENGER AIR BAG OFF" cle occupants are seated and indicator illuminates after the igni-

CAUTION

restrained properly (sitting upright tion key is turned to the "ON" posi- If the occupant classification

with the seat in an upright position, tion or after the engine is started. If system is not working properly, 1
centered on the seat cushion, with the front passenger's seat is occu- the air bag warning light ( ) on

the person's legs comfortably pied by a very small person or is the instrument panel will illumi-
extended, feet on the floor, and wear- occupied by someone who is nate. If there is a malfunction of 2

ing the safety belt properly) for the improperly seated, the "PASSEN- the occupant classification sys-

most effective protection by the air bag and the safety belt.

GER AIR BAG OFF" indicator will tem, the "PASSENGER AIR BAG remain illuminated and the front OFF" indicator will not illumi-

· The OCS may not function proper- passenger air bag will not deploy in nate and the front passenger's

ly if the passenger takes actions which can defeat the detection sys-

frontal crashes. If the front passen- air bag will deploy in frontal ger's seat is occupied by an adult crashes even if there is child or

tem. These include:
(1) Failing to sit in an upright position.
(2) Leaning against the door or cen-

size person seated properly, the "PASSENGER AIR BAG OFF" indicator will turn off after approximately 4 seconds and the front passenger's air bag will deploy in

no occupant in the front passenger's seat. If the SRS air bag warning light does not illuminate when the ignition key is turned to "ON" position, if it

5 6

ter console.

frontal collision.

remains illuminated after blink-

(3) Sitting towards the sides or the front of the seat.

ing for approximately six seconds, or if it illuminates while

(4) Putting legs on the dashboard or resting them on other locations which reduce the passenger weight on the front seat.
(5) Improperly wearing the safety

the vehicle is being driven, have

an authorized Kia dealer inspect 8

the occupant classification sys-

tem with the SRS air bag system as soon as possible.

belt.

(6) Reclining the seat back.

3 57

Knowing your vehicle

Condition and operation in the front passenger occupant classification system

CAUTION
If the "PASSENGER AIR BAG

Condition detected by

Indicator/Warning light

Devices

the occupant classification system

"PASSENGER AIR BAG OFF" indicator
light

SRS warning light Front passenger front air bag

1. Adult *1

Off

2. Child*2 or child

restraint system

Off

Activated

Off

Deactivated

OFF" indicator illuminates or blinks continuously when a person of adult size sits in the front passenger's seat, it could be because that person isn't sitting properly in the seat. If this happens, turn the vehicle off, make sure the seat back is not

3. Unoccupied

Off

Deactivated

reclined, have the passenger

center on the seat cushion, with

*1 The system detects a person who is generally adult size as an adult, thus allowing legs comfortably extended, and

the passenger air bag to deploy. When a smaller adult sits in the front passenger seat, the system may detect their body shape as that of a child, thus preventing air

the safety belt properly positioned. Restart the vehicle and

bag deployment. *2 When a larger child who has outgrown a child restraint system sits in the front pas-

have the person remain in this position long enough to allow

senger seat, the system may recognize him/her as an adult depending on his/her the system to detect the person

physique sitting posture, or objects in the lap of the occupant, thus permitting airbag deployment.

and activate the passenger air bag.

3 58

Knowing your vehicle

WARNING

(Continued)

If the front passenger seat should be modified for persons with disabilities that may affect the operation of the occupant classification system, contact an authorized Kia dealer.

· If the "PASSENGER AIR BAG OFF" indicator is illuminated when the front passenger's seat is occupied by a person of adult size who is seated properly, or if the "PASSENGER AIR BAG OFF" indicator is not illuminated when the

· If a very low weight adult is seated in the front passenger seat, the occupant classification system may or may not turn off the right front passenger air bag, depending upon the person's seating position and body type. Everyone in

1 2 3

front passenger's seat is

your vehicle should wear a

WARNING
· Even though your vehicle is equipped with the occupant classification system, do not install a child restraint system in the front passenger seat. The child could be severely injured or killed if the air bag deploys. Children are afforded the most protection in the

unoccupied or occupied by a very small person, the occu-

safety belt properly -- whether or not there is an air bag for

pant classification system is

that person.

not working properly. Have your vehicle immediately

· If the front seat passenger changes their seating position

inspected by your Kia dealer if the occupant classification

(for example, by not sitting upright, by sitting on the edge

system is not working proper-

of the seat, or by otherwise

ly.

(Continued)

being out of position), the "PASSENGER AIR BAG OFF"

event of an accident when they are restrained by the

indicator may be turned on,
and the passenger air bag 8

proper restraint system in the

may not deploy in a collision.

rear seat.

(Continued)

Always be sure to sit properly in the front passenger seat

and wear the safety belt prop-

erly.

(Continued)

3 59

Knowing your vehicle

(Continued)

1KMN3661

- Never put a heavy load in the

front passenger seat.

9 1KMN3662
- Never excessively recline the front passenger seatback.

3 60

1KMN3663
- Never sit with hips shifted towards the front of the seat.
1KMN3664
- Never lean on the center console.
- Never sit on one side of the front passenger seat.

1KMN3665
- Never place feet on the dashboard.
1KMN3666
- Always sit in a proper seating position. (Continued)

Knowing your vehicle

(Continued)
· Do not modify or replace the front passenger seat. This will disable the OCS unless a proper Kia replacement seat is used.
· Do not place sharp objects on

NOTICE
· If luggage or other objects are placed on the front passenger's seat or if the temperature of the seat changes while the seat is unoccupied, the "PASSENGER AIR BAG OFF" indicator may blink.

WARNING - Front passen-
ger seating
· The front seat passenger air bag is much larger than the steering wheel air bag and inflates with considerably

1 2

the front passenger seat.

These conditions do not indicate a

more force. It can seriously

These can damage the occupant classification system, if

problem. · Do not put heavy objects on the

hurt or kill a passenger who is not in the proper position and

they puncture the seat cush-

front passenger's seat. This may

wearing the safety belt proper-

ion.

cause front passenger air bag

ly. The front passengers 4

· Do not install accessory seat

deployment in the event of an acci-

should always move their seat

covers on the front seats, since these will interfere with

dent, thus increasing your repair costs.

as far back as practical and sit back in their seat.

proper sensor operation.

· It is essential that the front

passengers always wear their 6
safety belts when vehicle is in

motion, even when the vehicle
is moving in a parking lot or 7

up a driveway into garage.

(Continued) 8

3 61

Knowing your vehicle

(Continued)

· If the driver brakes the vehicle · Never allow children, pregnant

heavily prior to an impact, unbelted occupants will be

women or weak persons to sit in the front passenger seat.

thrown forward. If the front

Do not put child restraint sys-

passenger is not wearing the

tem on the front passenger's

safety belts, they will be

seat either. They may be seri-

directly in front of the air bag when deployment occurs. In

ously injured by the airbag inflation when airbag deploys.

1LDN2050/1LDN2051

that situation, serious injury · Do not put objects or stickers

or death is possible. · Never allow front passenger

on the instrument panel. Do not apply any accessory to the

to put their hands, feet or face

front windshield. Do not install

on or close to the instrument

aftermarket mirrors or acces-

panel. In the event of air bag

sories on the factory-installed

deployment, such a mispositioned occupant would be

rearview mirror. Any of these could interfere with the

likely to suffer severe injury or

death.

· Never allow children, pregnant

women or weak persons to sit in the front passenger seat.

They may be seriously injured

by the air bag inflation when air bag deploys.

deployment of the air bag or could hit your body at high speed and cause severe bodily injury and even death.

1LDA2056
Side air bag (if equipped)
Side air bags are stored in the left side of the driver's seat and right side of the front passenger's seat.
If air bag inflation conditions are met (side collision), they will inflate.

(Continued)

3 62

Knowing your vehicle

WARNING
· Do not use any accessory seat covers for the vehicle equipped with side air bags.
Use of seat covers could interfere with side air bag deployment.
If seat is damaged, have the vehicle checked and repaired by an authorized Kia dealer. Inform them that your vehicle is equipped with side air bags and an occupant detection system.

· The curtain air bag deployment

occurs only on the side of the vehi-

cle affected by the impact.

· The side air bags (side and curtain 1

air bags) are not designed to

deploy during collisions from the front or rear of the vehicle or in

most rollover situations.

1LDA2052 · The curtain air bags are designed 3

to deploy only during certain side-

impact collisions, depending on the crash severity, angle, speed and

impact.

· Do not make modifications or additions to the seats as they

may cause the air bag system

1LDA2057

to malfunction resulting in severe personal injury or

Curtain air bag (if equipped)

death.

Curtain air bags are located along

both sides of the roof rails above the front and rear doors.

They are designed to help protect the heads of the front seat occupants

and the rear outboard seat occupants

in certain side impact collisions.

3 63

Knowing your vehicle

WARNING - Side and cur-

(Continued)

tain air bags

· If a small child is seated on

1 2 3

· In order for side and curtain air bags to provide the best protection, both front seat occupants and both outboard rear occupants should sit in an upright position with the safety belts properly fastened.

the rear outboard seat cushion, it is probable that they will below the deployment level of the side curtain airbag and thus not protected by that airbag.
· Do not allow the passengers

Importantly, children should

to lean their heads or bodies

sit in a proper child restraint system in the rear seat.

onto doors, put their arms on the doors, stretch their arms

· When children are seated in the rear outboard seats, they

must be seated in the proper

child restraint system. Make

sure to put the child restraint

out of the window, or place objects between the doors and passengers when they are seated on seats equipped with side air bags.

system as far away from the · Never try to open or repair any

door side as possible, and

components of the side cur-

secure the child restraint sys-

tain air bag system. This

tem in a locked position. (Continued)

should only be done by an authorized Kia dealer.

Failure to follow the above men-

tioned instructions can result in severe injury or death to the

vehicle occupants in an acci-

dent.

3 64

Knowing your vehicle

Why didn't my air bag go off in a collision?

(Inflation and non-inflation conditions of the air bag)

There are many types of accidents in

which the air bag would not be

expected to provide additional pro-

tection. These include rear impacts, second

or third collisions in multiple impact

accidents, as well as low speed

impacts. In other words, just because

your vehicle is damaged and even if it is totally unusable, don't be sur-

prised that the air bags did not

inflate.

1JBA3512A/OMG035052/OMG035054/OMG035053/OMG035055

Air bag collision sensors

(1) SRS control module

(3) Side impact sensor (if equipped)

(2) Front impact sensor

3 65

Knowing your vehicle

WARNING

(Continued)

1 2

· Do not hit or allow any objects to impact the locations where air bag or sensors are installed.
This may cause unexpected

· Problems may arise if the sensor installation angles are changed due to the deformation of front bumper, body or B, C pillar where side collision sensors are installed. Have

air bag deployment, which could result in serious per-

the vehicle checked and repaired by an authorized Kia

sonal injury or death.

dealer.

· If the installation location or angle of the sensors is altered in any way, the air bags may

· Your vehicle has been designed to absorb impact and deploy the air bag(s) in

1LDA2059
Air bag inflation condition

5 6

deploy when they should not or they may not deploy when they should, causing severe injury or death.

certain collisions. Installing aftermarket bumper guards or replacing a bumper with nongenuine parts may adversely

Front air bag
Front air bags (driver's and front passenger's air bags) are designed to inflate when the impact is delivered

Therefore, do not try to per-

affect your vehicles collision to front collision sensors depending

form maintenance on or around the air bag sensors.

and air bag deployment per- on the intensity, speed or angles of

formance.

impact of the front collision - general-

Have the vehicle checked and

repaired by an authorized Kia

dealer.

ly from an area a little to the left to a little to the right of straight ahead.

(Continued)

3 66

Knowing your vehicle

Although the front air bags (driver's If the vehicle chassis is impacted by

and front passenger's air bags) are bumps or objects on unimproved

designed to inflate only in frontal col- roads or sidewalks, air bags may

lision, it may inflate in any collision if deploy. Drive carefully on unim- 1
front impact sensors detect a suffi- proved roads or on surfaces not

cient impact. Side air bags (side and designed for vehicle traffic.

curtain air bags) are designed to To protect occupants, front air bags 2

inflate only in side impact collision, it or pre-tensioner safety belts may

1JBA3514

may inflate in any collision if side impact sensors detect a sufficient

deploy in certain side impact collisions.

impact.

OUN026090

Side air bag (if equipped)

Side air bags (side and curtain air

bags) are designed to inflate when an impact is detected by side colli-

sion sensors depending on the

strength, speed or angles of impact

of side impact collision or rollover by

the side impact.

3 67

Knowing your vehicle

1LDA2061

1GHA2273

1JBA3516

Air bag non-inflation conditions · Frontal air bags are not designed · Front air bags may not inflate in

5 · In certain collisions, the vehicle
safety belts are sufficient to protect

the vehicle occupants and the air bags may not deploy. In some

cases, deploying air bags in low-

speed collisions can cause a secondary impact to the occupants

to inflate in rear collisions, because occupants are moved backward by the force of the impact. In this case, the air bags do not provide proper protection.

side impact collision, because occupants move to the direction of the collision, and thus in side impacts, frontal air bag deployment does not provide occupant protection.
However, side or curtain air bags

(light abrasions, cuts, burns, etc.),

or loss of vehicle control.

may inflate depending on the intensity, vehicle speed and angles of impact.

3 68

Knowing your vehicle

1GHA2270

1LDA2065

1LDA2066

· In a slant impact or collision, the · At the moment of an accident, driv- · Air bags may not inflate in rollover

force delivered will be relatively weaker than that of frontal colli-

ers often brake heavily with reflex. In such heavy braking, the front

accidents because air bag deployment would not provide proper pro-

sion. So, the air bags may not portion of the vehicle is lowered by tection to the occupants.

inflate.

the force of the braking and the vehicle can dive under a vehicle with a higher ground clearance. Air bags may not inflate in this situation because impacts may not be delivered or may be delivered with less intensity.

However, side air bags may inflate 6

when the vehicle is rolled over by a

side impact collision, if the vehicle is equipped with side air bags and

curtain air bags.

3 69

Knowing your vehicle

How does the air bag system · Air bag deployment depends on a

operate

number of factors including vehicle

· Air bag only operates when the ignition switch is turned to the ON or START positions.

speed, angles of impact and the density and stiffness of the vehicles or objects which your vehicle hits in the collision. Though, factors

· Air bags inflate instantly in the are not limited to those mentioned

event of serious frontal or side col- above.

lision (if equipped with side air bag or curtain air bag) in order to help protect the occupants from serious

· The front air bags will completely inflate and deflate in an instant.

1JBA3518

physical injury.

· Air bags may not inflate if the vehicle collides with objects such as utility poles or trees, where the

· There is no single speed at which the air bags will inflate.
Generally, air bags are designed to

It is impossible for you to see the air bags inflate during an accident. It is much more likely that you will simply see the deflated air bags hanging out of their storage com-

point of impact is concentrated to inflate by the severity of a collision partments after the collision.

one area and the full force of the impact is not delivered to the sen-

and its direction. These two factors determine whether the sensors

sors.

send out an electronic deployment/inflation signal.

3 70

Knowing your vehicle

· In order to help provide protection

Noise and smoke

in a severe collision, the air bags must inflate rapidly. The speed of air bag inflation is a consequence of the extremely short time in which a collision occurs and the need to get the air bag between the occupant and the vehicle structures before the occupant impacts those structures. This speed of inflation reduces the risk of serious or lifethreatening injuries in a severe collision and is thus a necessary part of air bag design.
However, air bag inflation can also

WARNING
· To avoid severe personal injury or death caused by deploying air bags in a collision, the driver should sit as far back from the steering wheel air bag as possible (at least 250 mm (10 inches) away). The front passenger should always move their seat as far back as possible and sit back in their seat.
· Air bag inflates instantly in an event of collision, passengers

When the air bags inflate, they make a loud noise and they leave smoke and powder in the air inside of the vehicle. This is normal and is a result of the ignition of the air bag inflator. After the air bag inflates, you may feel substantial discomfort in breathing due to the contact of your chest to both the safety belt and the air bag, as well as from breathing the smoke and powder. We strongly urge you to open your doors and/or windows as soon as possible after impact in order to reduce

1 2 3 4 5

cause injuries which normally can

may be injured by the air bag discomfort and prevent prolonged

include facial abrasions, bruises and broken bones, and sometimes

expansion force if they are not in proper position.

exposure to the smoke and powder.

more serious injuries because the inflation speed also causes the air bags to expand with a great deal of force.
· There are even circumstances

· Air bag inflation may cause injuries which normally include facial or bodily abrasions, injuries by the broken glasses or burns by the explo-

Though smoke and powder are nontoxic, it may cause irritation to the skin (eyes, nose and throat etc). Wash and rinse with the cold water immediately and consult the doctor if

7 8

under which contact with the

sives.

the symptom persists.

steering wheel air bag can cause fatal injuries, especially if the

occupant is positioned exces-

sively close to the steering

wheel.

3 71

Knowing your vehicle

WARNING

When the air bags deploy, the
1 air bag related parts in steering

· Extreme Hazard! Do not use a rearward facing child restraint

wheel and/or instrument panel

on a seat protected by an air

and/or in both sides of the roof rails above the front and rear

doors are very hot. To prevent

injury, do not touch the air bag storage areas internal compo-

nents immediately after an air

4 bag has inflated.

1JBH3051

bag in front of it!
· Never put child restraint in the front passenger's seat. If the front passenger air bag inflates, it would cause serious or fatal injuries.
· When children are seated in

Installing a child restraint on a

the rear outboard seats in

front passenger seat is extremely dangerous and

which curtain air bags are equipped, be sure to put the

6 7

should never be done.
Never place a rear-facing child restraint in the front passenger seat. If the air bag deploys, it would impact the rear-facing child restraint, caus-

child restraint system as far away from the door side as possible, and secure the child restraint system to be locked in position.

ing severe or fatal injury.

Inflation of curtain air bag (if

8 9

In addition, do not place front-facing child restraint in the front passenger's seat either. If the front passenger air bag inflates, it would cause

equipped) could cause severe injury or death due to the expansion impact.

serious or fatal injuries to the improp-

erly positioned or improperly

restrained child.

3 72

Knowing your vehicle

When the ignition switch is turned Air bag (Supplemental

ON, the indicator light should blink or Restraint System) service

illuminate for approximately 6 seconds, then go off.

Your Supplemental Restraint System is virtually maintenance-free. There

Have the system checked if:

are no parts which you can service.

· The light does not turn on briefly You must have the system serviced

when you turn the ignition ON.

under the following circumstances:

· The light stays on after the engine · If an air bag ever inflates, the air

starts.

bag must be replaced. Do not try to

· The light comes on while the vehi- remove or discard the air bag by

A-BAG-W
Air bag warning light
The purpose of air bag warning light in your instrument panel is to alert you of a potential problem with your air bag - Supplemental Restraint System (SRS).

cle is in motion.

yourself. This must be done by an 4
authorized Kia dealer.

· If the air bag warning indicator light alerts you to a problem, have the

air bag system checked as soon as

possible. Otherwise, your air bag system may be ineffective.

3 73

Knowing your vehicle

CAUTION

WARNING

Repairing or scrapping the vehicles

Do not modify any part of the · Do not modify your steering · Repairing steering wheel, instru-

1 Supplemental Restraint System.

wheel, seat or any other part

ment panel, center console or

Modification could make the air

of the Supplemental Restraint

roofs, or installing car audio around

bag system ineffective or could
2 cause unnecessary deploy-

System. Modification could make the system inoperable.

center console or painting front metal sheet could disable the air

ment.

· Do not work on the system's

bag system. Have them checked

components or wiring. This

by an authorized Kia dealer.

could cause the air bags to · When leaving the vehicle at an

inflate inadvertently, possibly seriously injuring someone.

authorized Kia dealer, inform the facility that the vehicle is equipped

Working on the system could

with air bag system, and leave the

5 6

also disable the system so that the air bags would not deploy in a collision.
· Any work on the SRS system,

owner's manual in the vehicle.
· Since air bag system contains explosive chemical substances, contact an authorized Kia dealer

such as removing, installing,

when scrapping the vehicle.

repairing, or any work on the steering wheel must be per-

formed by a qualified Kia tech-

nician. Improper handling of the air bag system may result

in serious personal injury or

death.

3 74

Knowing your vehicle

(if equipped)

4
(if equipped)
5

OLD036901N/1LDN2069A/1LDN2074/1LDE2069

Airbag warning label Airbag warning labels which are now required by the Canadian Motor Vehicle Safety Standards (CMVSS) are

attached to alert driver and passengers of potential risk of airbag system.

Note that these government warnings focus on the risk to children, Kia also wants you to be aware of the risks which adults are exposed to. Those have been described in previous pages.

3 75

Knowing your vehicle TRUNK (IF EQUIPPED)

OLD026014

1LDA2015

OLD026016N

Outside the vehicle

Trunk room lamp

Inside the vehicle

5 · To open the trunk, insert the key Trunk room lamp turns on when the To open the trunk from inside the

into the lock and turn it clockwise trunk is opened. It remains on until vehicle push trunk lid release switch.

(1).

the trunk is securely closed.

· To close the trunk, use both hands

to push the trunk lid down. Check

CAUTION

to see if the trunk is completely Make sure to close the trunk

shut.

securely. If it remains open

· Trunk can be opened with transmitter (if equipped).

while engine is not running, it may cause battery discharge

because trunk room lamp

remains on.

3 76

Knowing your vehicle

WARNING - Exhaust

WARNING

fumes If you drive with the trunk lid

No one should be allowed to
occupy the trunk of the vehicle 1

open, you will draw dangerous

at any time. If the trunk is par-

exhaust fumes into your vehicle causing serious injury or death

tially or totally latched and the person is unable to get out,

to vehicle occupants. Open

severe injury or death could

trunk lids can also dangerously obscure rear view vision.

occur due to lack of ventilation, exhaust fumes and rapid heat

If you must drive with the trunk lid open, keep the air vents open

build-up, or because of expo-

OLD026017 sure to cold weather conditions.

so that additional outside air Emergency trunk safety

comes into the vehicle.

release (if equipped)

The trunk is also a highly dan-

gerous location in the event of a crash because it is not a pro-

Your vehicle is equipped with an tected occupant space but

emergency trunk release cable locat- merely a part of the vehicle's ed inside the trunk. The lever glows crush zone.

in the dark when the trunk lid is

closed. If someone is inadvertently

locked in the trunk, pulling this han-

dle will release the trunk latch mech-

anism and open the trunk.

3 77

Knowing your vehicle

HOOD

WARNING

· If a person is locked in the

trunk, they can pull the emer-

gency release to open the

trunk lid. · We recommend that cars be

kept locked and keys be kept

out of the reach of children,

and that parents teach their

children about the dangers of playing in trunks.

1LDA2020

OLD026023

Opening the hood:

2. Go to the front of the vehicle,

5 6

1. Pull the release lever on the lower left side of the instrument panel to unlatch the hood. The hood should pop open slightly.

slightly raise the hood, push the secondary latch (1) inside of the hood center and lift (2) the hood.

3 78

Knowing your vehicle

Closing the hood

1. Before closing the hood, check the

WARNING

following:
· All filler caps in engine compartment must be correctly installed.
· Gloves, rags or any other com-

· Before closing the hood, make sure that all engine parts and tools have been removed from the engine area and that no one's hands are near the hood

1 2

bustible material must be

opening.

removed from the engine compartment.

· Do not leave gloves, rags or any other combustible materi-

2. Secure the support rod in its clip. 1LDA2166 3. Lower the hood to about 30 cm

al in the engine compartment. Doing so may cause a heat-

3. Lift the hood and hold it open with (12 inches) height and then let it

induced fire.

the prop rod by inserting the free end of the rod into the slot in the

drop to properly lock in place. Make sure the hood is properly

hood.

locked before driving.

WARNING

Handle the support rod in the

area wrapped in rubber. The rub-

ber will help prevent you from being burned by hot metal when

the engine is hot.

3 79

Knowing your vehicle

FUEL FILLER LID

WARNING

If pressurized fuel sprays out, it

can cause serious injuries.

Always remove the fuel cap

carefully and slowly. If the cap is venting fuel or if you hear a

hissing sound, wait until the

condition stops before completely removing the cap.

OLD026018

1LDA2019

1. Stop the engine.

3. Pull the fuel filler lid out to open.

WARNING

5 2. To open the fuel filler lid, pull the 4. To remove the cap, turn the fuel

release lever.

tank cap counterclockwise.

Automotive fuels are flammable/explosive materials. When

6
WARNING

5. Refuel as needed. 6. To install the cap, turn it clockwise

refueling, please note the following guidelines carefully.

7 8

To avoid injury from sharp edges, it is recommended that protective gloves be worn if there is a need to open the fuel filler door manually.

until it "clicks". This indicates that the cap is securely tightened.
7. Close the fuel filler lid and push it lightly and make sure that it is securely closed.

Failure to follow these guidelines may result in severe personal injury, severe burns or death by fire or explosion.
· Before refueling always note the location of the Emergency

Gasoline Shut-Off, if available, at the gas station facility.

(Continued)

3 80

Knowing your vehicle

(Continued)

· Before touching the fuel noz- · When using a portable fuel · When refueling always shut

zle or fuel filler cap, you should eliminate potentially

container be sure to place the container on the ground prior

the engine off. Sparks produced by electrical compo-

dangerous static electricity

to refueling. Static electricity

nents related to the engine

discharge by touching another metal part of the front of the

discharge from the container can ignite fuel vapors causing

can ignite fuel vapors causing 2
a fire. Always insure that the

vehicle, a safe distance away from the fuel filler neck, noz-

a fire. Once refueling has begun, contact with the vehi-

engine is OFF before and during refueling. Once refueling

zle, or other gas source.

cle should be maintained until

is complete, check to make

· Do not get back into a vehicle once you have begun refueling. Do not touch, rub or slide against any item or fabric

the filling is complete. Use only portable fuel containers

sure the fuel filler cap and door are securely closed,

designed to carry and store

before starting the engine.

gasoline.

· Do not light any fire around a 5

(polyester, satin, nylon, etc.) · Do not use cellular phones

gas station. DO NOT use

capable of producing static electricity. Static electricity

around a gas station or while refueling any vehicle. Electric

matches or a lighter and DO NOT SMOKE or leave a lit cig-

discharge can ignite fuel

current and/or electronic

arette in your vehicle while at

vapors resulting in explosion. If you must re-enter the vehi-

interference from cellular phones can potentially ignite

a gas station especially during refueling. Automotive fuel is

cle, you should once again

fuel vapors causing a fire. If

highly flammable and can,

eliminate potentially danger-

you must use your cellular

when ignited, result in explo- 8

ous static electricity dis-

phone, use it in a place away

sion by flames.

charge by touching a metal part of the vehicle, away from the fuel filler neck, nozzle or

from the gas station. (Continued)

(Continued) 9

other gasoline source.

(Continued)

3 81

Knowing your vehicle

(Continued)

· If a fire breaks out during refu-

eling, leave the vicinity of the vehicle, and immediately con-

tact the manager of the gas

station or contact the police

and local fire department.

Follow any safety instructions they provide.

4
CAUTION

· Make sure to refuel with gasoline (unleaded fuel) only for

the gasoline engine vehicles.
6 · Check to make sure the fuel

filler cap is securely closed

after refueling.

(Continued)

3 82

(Continued)
· If the fuel filler cap requires replacement, use only a genuine Kia cap or the equivalent specified for your vehicle. An incorrect fuel filler cap can result in a serious malfunction of the fuel system or emission control system. Correct replacement caps are available at authorized Kia dealers.
· Do not spill fuel on the exterior surfaces of the vehicle. Any type of fuel spilled on painted surfaces may damage the paint.
· A loose fuel filler cap may cause the "Check Engine" (Malfunction Indicator) light in the instrument panel to illuminate unnecessarily.
· If the fuel filler lid will not open in cold weather because the area around it is frozen, push or lightly tap the lid.

OLD026020
Auto fuel cutoff switch (if equipped)
The auto fuel cutoff switch is located on the driver's side of the engine compartment. In the event of a collision or sudden impact, the auto fuel cutoff device cuts off the fuel supply. If this device is activated, it must be reset by pressing in on the top of the switch before the engine can be restarted.
WARNING
Before resetting the auto fuel cutoff switch, the fuel line should be checked for fuel leaks.

MIRRORS
Outside rearview mirror
Be sure to adjust mirror angles before driving.
Your vehicle is equipped with both left-hand and right-hand outside rearview mirrors. The mirrors can either be adjusted remotely with the control levers or remote switch, depending on the type your vehicle has. The mirror heads can be folded back to prevent damage when using an automatic car wash or passing in a narrow street.

WARNING
· The right outside rearview mirror is convex. Objects seen in the mirror are closer than they appear.
· Use your interior rearview mirror or direct observation to determine the actual distance of following vehicles when changing lanes.

Knowing your vehicle

CAUTION

Do not scrape ice off the mirror

face; this may damage the sur- 1
face of the glass. If ice should

restrict movement of the mirror,
do not force the mirror for 2

adjustment. To remove ice, use

a deicer spray, or a sponge or soft cloth with very warm water.

3 83

Knowing your vehicle

CAUTION

· The mirrors stop moving when

they reach the maximum

adjusting angles, but the

motor continues to operate

while the switch is depressed.

Do not depress the switch

longer than necessary, the motor may be damaged.

· Do not attempt to adjust the

1LDA2081

1LDN2080

outside rearview mirror by

Manual remote control
5 (if equipped)

Electric remote control (if equipped)

hands. Doing so may damage the parts.

To adjust an outside mirror, move the The electric remote control mirror

control lever which is located at the switch allows you to adjust the posiforward inside area of the window tion of the left and right outside

frame.

rearview mirrors. To adjust the posi-

tion of either mirror, move the lever (1) to R or L to select the right side

mirror or the left side mirror, then

press a corresponding point (·) on

the mirror adjustment control to posi-

tion the selected mirror up, down, left

or right.

After adjustment, put the lever into neutral position to prevent the inadvertent adjustment.

3 84

Knowing your vehicle

Outside rearview mirror heater

Day/night rearview mirror

(if equipped)

Adjust the rearview mirror to center

The outside rearview mirror heater is on the view through the rear window. actuated in connection with the rear Make this adjustment before you

window defroster. To heat the outside start driving.

rearview mirror glass, push the button for the rear window defroster.
The outside rearview mirror glass will

WARNING

be heated for defrosting or defogging Do not place objects in the rear and will give you improved rear seat or cargo area which would

vision in inclement weather condi1LDA2083 tions. Push the button again to turn

interfere with your vision out the rear window.

Folding the outside rearview

the heater off. The outside rearview

mirror Manual type

mirror heater automatically turns off after 20 minutes.

To fold outside rearview mirror, grasp the housing of mirror and then fold it

toward the rear of the vehicle.

3 85

Knowing your vehicle

Day/Night lever

When the ignition switch is ON, the automatic-dimming function will turn

on automatically.

Press the ON/OFF button (1) to turn

the automatic-dimming function off.

The mirror indicator light will turn off. Press the ON/OFF button (1) once

Day Night

again to turn the automatic-dimming function on. The mirror indicator light will illuminate.

4
Manual type

1LDA2078

Indicator Sensor
1KMA3084
Electric type (if equipped)

CAUTION

Make this adjustment before you When the engine is running, the start driving and while the day/night glare is automatically controlled by

When cleaning the mirror, use a paper towel or similar material

6 7

lever is in the day position.
Pull the day/night lever toward you to reduce glare from the headlights of vehicles behind you during night driving.

the sensor mounted in the rearview mirror.
The sensor mounted in the mirror senses the light level around the vehicle, and through a chemical reaction,

dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing.

Remember that you lose some automatically controls the headlight rearview clarity in the night position. glare from vehicles behind you.

Whenever the shift lever is shifted

into reverse (R), the mirror will automatically go to the brightest setting in

order to improve the drivers view

behind the vehicle.

3 86

INTERIOR LIGHTS
Type A

Knowing your vehicle

Type B

OLD026111

1LDA2113

1LDN3202

Dome light (if equipped)

Door courtesy lamp

(1) OFF - The light stays off even (if equipped)

when a door is open.

The door courtesy lamp comes ON

(2) DOOR - The light turns on when a when the door is opened to assist door is opened or when a door is entering or exiting the vehicle. It also

unlocked by the transmitter (if serves as a warning to passing vehi-

equipped). Interior light goes out cles that the vehicle door is open.

Map light

OLD026112

slowly after 30 seconds if the door is closed. However if the ignition switch is ON or all vehicle

Front (if equipped)

doors are locked when the door is

The lights are turned ON or OFF by pressing the corresponding switch.

closed, interior light will turn off even within 30 seconds.

(3) ON - The light turns on and stays

on even when the doors are all

closed.

3 87

Knowing your vehicle

STORAGE COMPARTMENT

CAUTION

· To avoid possible theft, do not

leave valuables in the storage compartment.

· Always keep the storage compartment covers closed while

driving. Do not attempt to

place many items in the storage compartment that the

storage compartment cover

can not close securely.

WARNING - Flammable
materials
Do not store cigarette lighters, propane cylinders, or other flammable/explosive materials in the vehicle. These items may catch fire and/or explode if the vehicle is exposed to hot temperatures for extended periods.

OLD026151
Center console storage
To open either of the console storage compartments, push the button (1) or pull up the lever (2).
These compartments can be used to store small items required by the driver or front passenger.

3 88

Knowing your vehicle

CAUTION

Since key is not fully inserted

into the glove box key set, do not apply excessive force.

Doing so may damage the parts.
2

1LDA2156
Glove box
To open the glove box, pull the handle (1) then the glove box will automatically open (2). Close the glove box after use.

1LDA2159

Sunglass holder

A sunglass storage compartment is 5

provided on the overhead console.

To open the sunglass holder, press the cover and the holder will slowly

open. Place your sunglasses in the

compartment door with the lenses facing out. Push to close.

CAUTION

Make sure the sunglass holder

is closed while driving.

3 89

Knowing your vehicle

INTERIOR FEATURES

CAUTION

· Do not hold the lighter in after

it is already heated because it will overheat.

· Only a genuine Kia lighter should be used in the ciga-

rette lighter socket. The use of

plug-in accessories (shavers, hand-held vacuums, and cof-

fee pots, for example) may

4
Cigarette lighter

OLD026148

damage the socket or cause

electrical failure.

Ashtray

OLD026147

5 Front

· If the lighter does not pop out within 30 seconds, remove it

Front

To operate the cigarette lighter, press

to prevent overheating.

The front ashtray may be opened by

it in and release it. When it is heated, it automatically pops out ready for

pushing in the ashtray lid. To clean the ashtray, the plastic receptacle

use.
7 If the engine is not running, the igni-
tion switch must be in the ACC posi-

should be removed by lifting the plastic ash receptacle upward and pulling it out.

8 tion for the lighter to operate.

WARNING - Ashtray use

· Do not use the vehicle's ash-

trays as waste receptacles.

· Putting lit cigarettes or matches in an ashtray with other combustible materials may cause a fire.

3 90

Knowing your vehicle

Cup holder

WARNING - Hot liquids
· Do not place uncovered cups

of hot liquid in the cup holder

while the vehicle is in motion.

If the hot liquid spills, you

could be burned. Such a burn

to the driver could cause a

loss of control of the vehicle.

· To reduce the risk of personal injury in the event of sudden stop or collision, do not place

Front

OLD026152
Rear (if equipped)

OLD026153

uncovered or insecure bot- Cups or small beverage cans may be To use cup holders in rear seat, pull 5

tles, glasses, cans, etc., in the placed in the cup holders.

the rear cup holder cover (1) out.

cup holder while the vehicle is in motion.

Push the cover to close after use.

CAUTION

Do not place heavy cups or 7

cans in cup holders. Cup hold-

ers could be damaged.

3 91

Knowing your vehicle

CAUTION

Close the vanity mirror cover

securely and return the sunvisor to its original position after

use. If the vanity mirror is not

closed securely, the lamp (if

equipped) will stay on and could

result in battery discharge and possible sunvisor damage.

1LDN2151

Sunvisor

5 Use the sunvisor to shield direct light
through the front or side windows.

6 To use a sunvisor, pull it downward.

To use a sunvisor for a side window,

pull it downward, unsnap it from the bracket (1) and swing it to the side.

To use the vanity mirror, pull down
8 the visor and pull up the mirror cover
(2).

OLD026150
Power socket (if equipped)
The power outlets are designed to provide power for mobile telephones or other devices designed to operate with vehicle electrical systems. The devices should draw less than 10 amps with the engine running.

3 92

Knowing your vehicle

CAUTION

· MINUTE: Pressing the "M" button with your

· Use when the engine is run-

finger, a pencil or similar object will

ning, and remove a plug from the power outlet after using

advance the time displayed by one 1
minute.

the electric appliance. Using electrical accessories when

· RESET:

the engine is not running may

To clear away minutes, press the

result in battery discharge.
· Only use 12V accessories which are rated for less than 10A maximum current draw.

1LDN2150

"R" button with your finger, a pencil or similar object. Then the clock will

be set precisely on the hour.

For example, if the "R" button is pressed while the time is between

· Adjust the air-conditioner or Digital clock (if equipped)

9:01 and 9:29, the display will be

heater to the lowest operation level when you have to use the power socket while using airconditioner or heater.

Whenever the battery terminals, ROOM fuse, or Power Connect are disconnected, you must reset the time.

reset to 9:00.
9:01 ~ 9:29 9:00 9:30 ~ 9:59 10:00

5 6

· Close the cover when not in use.
· Some electronic devices can cause electronic interference when plugged into a vehicle's power outlet. These devices

When the ignition switch is in the ACC or ON position, the clock buttons operate as follows:
· HOUR:

Display conversion
To change the 12 hour format to the 24 hour format, press the "R" button for more than 4 seconds.
For example, if the "R" button is

7 8

may cause excessive audio static and malfunctions in other electronic systems or

Pressing the "H" button with your finger, a pencil or similar object will advance the time displayed by one

pressed for more than 4 seconds while the time is 10:15 p.m., the display will be changed to 22:15.

devices used in your vehicle.

hour.

3 93

Knowing your vehicle

SUNROOF (IF EQUIPPED)

CAUTION

Sliding the sunroof

1 2 3

· Do not continue to press the sunroof control button(s) after the sunroof is in the fully open, closed, or tilt position(s). Damage to the motor or system components could occur.
· The sunroof cannot slide when it is in the tilt position

Autoslide open
To use the autoslide feature, momentarily (less than 0.4 second) press the SLIDE OPEN ( ) button on the overhead console. The sunroof will slide all the way open. To stop the sunroof sliding at any point, press any sunroof control button.
Manual slide open

OLD026022

nor can it be tilted while in an Press the SLIDE OPEN ( ) button

If your vehicle is equipped with this

feature, you can slide or tilt your sunroof with the sunroof control buttons

open or slide position.

on the overhead console for more than 0.4 second.
Close

located on the overhead console.
6 (1) Slide button
(2) Tilt button
7 (3) Close button

To close the sunroof, press the CLOSE ( ) button on the overhead console and hold it until the sunroof is closed.

The sunroof can only be opened,

closed, or tilted when the ignition switch is in the "ON" position.

3 94

Knowing your vehicle

Tilting the sunroof
Autotilt open
To use the autotilt feature, momentarily (less than 0.4 second) press the TILT UP ( ) button on the overhead console. The sunroof will tilt all the way open. To stop the sunroof tilting at any point, press any sunroof control button.
Manual tilt open
Press the TILT UP ( ) button on the overhead console for more than 0.4 second.
Close
To close the sunroof, press the CLOSE ( ) button on the overhead console and hold it until the sunroof is closed.

E2BLA361
Sunshade
The sunshade will be opened with the glass panel automatically when the glass panel is slid. You will have to close it manually if you want it closed.

CAUTION

· Do not press any sunroof con-

trol button longer than necessary. Damage to the motor or

system components could

occur.

· Periodically remove any dirt

that may accumulate on the guide rail.

· If you try to open the sunroof when the temperature is

below freezing or when the

sunroof is covered with snow or ice, the glass or the motor

could be damaged.

· The sunroof is made to slide 6

together with sunshade. Do

not leave the sunshade closed while the sunroof is open.

WARNING

· Do not extend face or arms outside through the sunroof

opening while driving.

· Make sure hand and face are safely out of the way before closing a sunroof.

3 95

Knowing your vehicle

Resetting the sunroof

3. Then, release it.

Whenever the vehicle battery is dis- 4. Press and hold the TILT UP ( )

connected or discharged, or you use the emergency handle to operate the

button once again until the sunroof has returned to the original

sunroof, you have to reset your sun-

position of TILT UP ( ) after it is

roof system as follows:

raised a little higher than the maximum TILT UP ( ) position.

1. Turn the ignition key to the ON When this is complete, the sunroof

position.

system is reset.

2. According to the position of the

1LDN3201

sunroof, do as follows.

In case of an emergency
5 If the sunroof does not open electri-

1) in case that the sunroof has closed completely or been tilted

cally:

6 1. Open the sunglass holder.

2. Remove the two (2) screws, and

then remove the overhead console.

3. Insert the emergency handle (pro-

vided with the vehicle) and turn

the handle clockwise to open or

counterclockwise to close.
9

: Press the TILT UP ( ) button for 1 second.
2) in case that the sunroof has slide-opened
: Press and hold the CLOSE ( ) button for more than 5 seconds until the sunroof has closed completely. And then press the TILT UP ( ) button for 1 second.

3 96

LUGGAGE NET (IF EQUIPPED)
CAUTION
Do not put fragile, bulky or excessive quantity of items into luggage net. They could be damaged.

MMSA3066
To keep items from shifting in the trunk, you can use the four rings located in the trunk to attach the cargo net.

WARNING
To avoid eye injury. DO NOT overstretch the netting.
ALWAYS keep face and body out of recoil path.
DO NOT use the luggage net when strap has visible signs of wear or damage.

Knowing your vehicle
1 2 3 4 5 6 7 8 9
3 97

Knowing your vehicle ANTENNA

1LDN3204

6LDN3001A

OLD026157

Fixed rod antenna

Roof type antenna (if equipped) Aux outlet

5 (if equipped)

If your vehicle has an audio system, You can use an aux outlet to connect

Your car uses a fixed rod antenna to an amplifying antenna is installed in an audio device.

receive both AM and FM broadcast your vehicle.

signals.

This antenna is removable. To remove NOTICE

This antenna is removable. To the antenna, turn it counterclockwise. When using a portable audio device remove the antenna, turn it counter- To install the antenna, turn it clockwise. connected to the power outlet, noise

clockwise. To install the antenna, turn it clockwise.

CAUTION
· Be sure to remove the antenna

may occur during playback. If this happens, use the power source of the portable audio device.

before washing the car in an

automatic car wash or it may be damaged.

· When reinstalling your antenna, it is important that it is fully tightened to ensure proper reception.

3 98

Knowing your vehicle

AUDIO SYSTEM
FM reception
¢¢¢

However, in some cases the signal coming to your vehicle may not be strong and clear. This can be due to factors such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.

AM reception
¢ ¢¢

¢ ¢¢

JBM001
How car audio works
AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers.
When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures the best possible quality reproduction.

JBM002

AM broadcasts can be received at

greater distances than FM broadcasts. This is because AM radio

waves are transmitted at low fre-
quencies. These long, low frequency 6
radio waves can follow the curvature

of the earth rather than travelling straight out into the atmosphere. In

addition, they curve around obstruc-

tions so that they can provide better signal coverage.

3 99

Knowing your vehicle

FM radio station

¢ ¢¢

JBM003

JBM004

JBM005

FM broadcasts are transmitted at · Fading - As your car moves away · Station Swapping - As a FM signal

high frequencies and do not bend to follow the earth's surface. Because

from the radio station, the signal will weaken and sound will begin to

weakens, another more powerful signal near the same frequency

of this, FM broadcasts generally
6 begin to fade at short distances from
the station. Also, FM signals are eas-

fade. When this occurs, we suggest that you select another stronger station.

may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs,

ily affected by buildings, mountains, · Flutter/Static - Weak FM signals or or other obstructions. These can large obstructions between the

select another station with a stronger signal.

result in certain listening conditions transmitter and your radio can dis- · Multi-Path Cancellation - Radio

which might lead you to believe a problem exists with your radio. The

turb the signal causing static or fluttering noises to occur. Reducing

signals being received from several directions can cause distortion

following conditions are normal and the treble level may lessen this or fluttering. This can be caused by

9 do not indicate radio trouble:

effect until the disturbance clears.

a direct and reflected signal from

the same station, or by signals

from two stations with close fre-

quencies. If this occurs, select

another station until the condition

has passed.

3 100

Knowing your vehicle

Using a cellular phone or a two-way radio
When a cellular phone is used inside the vehicle, noise may be produced from the audio equipment. This does not mean that something is wrong with the audio equipment. In such a case, use the cellular phone at a place as far as possible from the audio equipment.
WARNING - Cellular
phones
Don't use a cellular phone when you are driving. The driver must stop at a safe place to use a cellular phone.

Care of cassette tapes

Because tape media can be

(if equipped)

torted when exposed to direct sun-

Because the thickness of a

sette tape with the total playback

time of over 60 minutes (C-60) are

light, Do not leave cassette tapes on the seats, dashboard or near the back windshield.

too thin, we suggest that you do not use any of them to avoid hav-

ing tapes being tangled.

To achieve better sound qu

periodically clean the tape head

using a cotton stick with colorless alcohol (once per month).

If a tape is too loose, fasten

reel by winding with objects like a

pencil.

Because dust or foreign objec

a cassette tape may damage the

playback head, always store tapes

in their cases when not in use.

Make sure cassette tapes are

away from magnetic devices (TV, stereo system, etc) in order to

achieve better sound quality.

Be certain that no objects or

stances other than cassette tapes

are inserted into the cassette tape

player.

3 101

Knowing your vehicle

Care of disc (if equipped)

· Make sure on undesirable matter NOTICE - Playing an

· If the temperature inside the car is

too high, open the car windows for ventilation before using your car

other than CDs are inserted into the CD player (Do not insert more than one CD at a time).

Incompatible Copy-Protected Audio CD
Some copy-protected CDs, which do

audio.

· Keep CDs in their cases after use not comply with the international

2 · It is illegal to copy and use
MP3/WMA/AAC/WAVE files with-

to protect them from scratches or audio CD standards (Red Book),

dirt.

may not play on your car audio.

out permission (If equipped with · Depending on the type of CD- Please note that if you try to play

M465, use only MP3/WMA, if R/CD-RW CDs, certain CDs may copy protected CDs and the CD

equipped with M445, use only CD- not operate normally according to player of your car audio is not per-

DA). Use CDs that are created only by lawful means.

manufacturing companies or mak- forming to your expectation, this ing and recording methods. In such may be caused by those CDs and not

· Do not apply volatile agents such

as benzene and thinner, normal

cleaners and magnetic sprays

made for analogue disc onto CDs. · To prevent the disc surface from

circumstances, if you still continue to use those CDs, they may cause the malfunction of your car audio system.

a defect in the device itself. Please replace those CDs.

getting damaged. Hold and carry

CDs by the edges or the edges of

the center hole only.

· Clean the disc surface with a piece of soft cloth before playback (wipe

it from the center to the outside

edge).

· Do not damage the disc surface or

attach pieces of sticky tape or

paper onto it.

3 102

STEREO RADIO OPERATION (M445) (IF EQUIPPED)

Knowing your vehicle

1. POWER ON-OFF, VOLUME Control Knob

2. BAND (AM/FM) Select Buttons

3. TUNE Select/AUDIO Control Knob

4. AUTO SEEK Select Button

5. SCAN Button

6. EQ Button

7. PRESET STATION Select Buttons

9
LD 445 NA

3 103

Knowing your vehicle

1. POWER ON-OFF Control

3. TUNE Select/AUDIO Control TREBLE Control

Knob

To increase the TREBLE, rotate the

· The radio unit may be operated Rotate the knob clockwise to knob clockwise, while to decrease when the ignition key is in the increase the frequency and turn the the TREBLE, rotate the knob coun-

"ACC"or "ON" position. Press the knob counterclockwise to reduce the terclockwise.

2 3

knob to switch the power on. The LCD shows the radio frequency in radio mode, and displays the CD track in CD mode. To switch the power off, press the knob again.

frequency.
Audio Control Pressing the Audio Control knob changes the BASS, MID-RANGE,

FADER Control
Rotate the control knob clockwise to emphasize rear speaker sound (front speaker sound will be attenuated).

4 5

· Push the FM/AM or CD to turn on that function without pushing the Power ON-OFF control knob.
VOLUME Control

TREBLE, FADER and BALANCE mode.
The mode selected is shown on the display.
After selecting each mode, rotate the

When the control knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).
BALANCE Control

Rotate the knob clockwise to Audio control knob clockwise or Rotate the knob clockwise to empha-

increase the volume and turn the counterclockwise.

size right speaker sound (left speak-

knob counterclockwise to reduce the

volume.

BASS Control

er sound will be attenuated). When the control knob is turned counter-

To increase the BASS, rotate the clockwise, left speaker sound will be

2. BAND Selector

knob clockwise, while to decrease emphasized (right speaker sound

8 FM Selection Button

the BASS, rotate the knob counter- will be attenuated). clockwise.

Pressing the FM button changes

9 the FM1 and FM2 bands.

MID-RANGE Control

To increase the MID-RANGE, rotate

AM Select Button

the knob clockwise, while to

Pressing the AM button selects decrease the MID-RANGE, rotate

the AM band. AM mode is displayed the knob counterclockwise.

on the LCD.

3 104

Knowing your vehicle

4. AUTO SEEK Select Button 7. PRESET STATION Select

· Press and hold the station select

(Automatic Channel Selection) Buttons

button for more than 0.8 seconds.

Press the AUTO SEEK select button. When the side is pressed, the unit will automatically tune to the next higher frequency and when the side is pressed, it will automatically

Six stations for AM, FM1 and FM2 respectively can be preset in the electronic memory circuit.
HOW TO PRESET STATIONS

A select button indicator will show

in the display indicating which select button you have depressed.

The frequency display will flash

after it has been stored into the 2

memory. You should then release

tune to the next lower frequency.
5. SCAN Button When you Press the button, frequency is changed and the next channel is received automatically. To stay on a station, press the SCAN button again.

Six AM and twelve FM stations may be programmed into the memory of the radio. Then, by simply pressing the AM/FM band select buttons and/or one of the six station select buttons, you may recall any of these stations instantly.
To program the stations, follow these steps:

the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM stations per button.
· When completed, any preset station may be recalled by selecting AM, FM1 or FM2 band and the appropriate station button.

3 4 5 6

6. EQ Button

CAUTION

Press the EQ button to select the CLASSIC, POPS, ROCK, JAZZ and

· Press AM/FM selector to set the band for AM, FM1 and FM2.

· Do not place beverages close to the audio system. The audio

OFF MODE for the desired tone · Select the desired station to be quality. Each press of the button stored by seek or manual tuning.

system mechanism may be damaged if you spill them.

changes the display as follows;

· Determine the preset station select · Do not strike or allow anything

CLASSICPOPSROCKJAZZOFF

button you wish to use to access that station.

to impact the audio system, 9
damage to the system mecha-

nisms could occur.

3 105

Knowing your vehicle

COMPACT DISC PLAYER OPERATION (M445) (IF EQUIPPED)
1 2 3 4 5 6 7 8 9

1. CD/AUX Select Button 2. TRACK UP/DOWN Button 3. FF/REW Button 4. REPEAT (RPT) Button 5. CD SCAN Button 6. CD EJECT Button 7. RANDOM (RDM) Button
LD 445 NA

3 106

Knowing your vehicle

1. CD/AUX Select Button

(Continued)

NOTICE

CD Select
· Insert the CD with the label facing upward.
· Insert the CD to start CD playback, during radio operation.
· When a disc is in the CD deck, if

Please refer to the manual of CDR/CD-RW recoder or CD-R/CDRW software for more information on finalization process. · Depending on the recording status, some CD-Rs/CD-RWs may not be played on this unit.

1 2

you press the CD/AUX button the CD player will begin playing even if AUX-IN Select

mode or RADIO mode).

· The quality of sound may be

the radio player is being used.
· The CD/AUX player can be used when the ignition switch is in either the "ON" or "ACC" position.
· Push the CD/AUX button to turn on that function without pushing the Power ON-OFF control knob.

· When the AUX device (such as portable MP3 players) is connected to vehicle's AUX-IN terminal, you can switch to AUX-IN mode by pressing CD/AUX button.
· With a CD loaded and AUX device connected at the same time, this button switches between AUX-IN

defected or distorted when the
unit's EQ (BASS/MID/TREBLE) 4

control and AUX device's EQ con-

trol are both enabled (not flat). When you want to use the unit's

EQ control feature, disable the

AUX device's EQ control feature, and vice versa.

NOTICE

mode and CD mode.

· When using a portable audio
device connected to the power out- 7

· Do not stick paper or tape etc., on the label side or the recording side

AUX

3.5mm STEREO MINI PLUG

of any discs, as it may cause a mal-

let, noise may occur during play-

back. If this happens, use the power source of the portable audio

function.

device.

· The unit cannot play a CDR(Recordable CD) and CD-

RW(Rewritable CD) that is not

finalized.

(Continued)

3 107

Knowing your vehicle

2. TRACK UP/DOWN Button

4. REPEAT (RPT) Button

6. CD EJECT Button

· The desired track on the disc cur- · To repeat the track you are current- When the button is pressed with a

rently being played can be selected using the track number.

ly listening to, press the RPT but- CD loaded, the CD will eject.

ton. To cancel, press it again.

Forcing to eject : To force to eject a

· Press button once to skip for- · If you do not release RPT opera- CD, press this button for more than 3

ward to the beginning of the next track.

tion when the track ends, it will seconds.

automatically be replayed.

(Do this only when a CD is jammed

Press within a second after playback begins to quickly move

This process will be continued until and you can not eject it in the normal you push the button again or turn way - e.g.) in case that you have

backward through a CD.

the Power OFF then ON.

inserted 2 CDs by mistake)

If you press after more than a

second, it will take you to the 5. CD SCAN Button

7. RANDOM (RDM) Button

beginning of the track you are now listening to.

· To playback the first 10 seconds of each track, press the CD SCAN button.

With random, you can listen to the tracks in random, rather than sequential order.

6 3. FF/REW Button

· Press the CD SCAN button again within 10 sec. when you have

To use random, do the following:

If you want to fast forward or reverse
7 through the compact disc track, push

reached the desired track.

Press the RDM button to listen to recorded tracks in random

and hold the FF or REW button.

sequence. Press RDM again to can-

When you release the button, the compact disc player will resume

playing.

cel or turn the power OFF then ON. The unit defaults to playing tracks in sequential order.

3 108

Knowing your vehicle

NOTICE
· To assure proper operation of the unit, keep the vehicle interior temperature within a normal range by using the vehicle's air conditioning or heating system.
· When replacing the fuse, replace it with a fuse having the correct capacity.
· All stored bookmarks are all erased when the car battery is disconnected or power to the vehicle is lost. If this occurs, the bookmarks will have to be reset.
· This equipment is designed to be used only in a 12 volt DC battery system with negative ground.
· This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.
· Do not expose this equipment (including the speakers and CD) to water or excessive moisture.

CAUTION
· Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.
· Do not insert anything like coins into the player slot as damage to the unit may occur.
· Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
· Do not strike or allow anything to impact the audio system, damage to the system mechanisms could occur.
· Off-road or rough surface driving may cause the compact disc to skip. Do not use the compact disc when driving in such conditions as

(Continued)
· Do not attempt to grab or pull the compact disc out while the disc is being pulled into the audio unit by the self-loading mechanism. Damage to the audio unit and compact disc could occur.
· Avoid using recorded compact discs in your audio unit. Original compact discs are recommended for best results.
WARNING
When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.

1 2 3 4 5 6 7 8

damage to the compact disc

face could occur. (Continued)

3 109

Knowing your vehicle
STEREO RADIO OPERATION (M445MP3) (IF EQUIPPED)
1 2 3 4 5 6 7 8 9
3 110

1. POWER ON-OFF, VOLUME Control Knob 2. AUDIO Select Button 3. BAND Select Button 4. SCAN Button 5. EQ Button 6. AUTO SEEK Select Button 7. TUNE Select/AUDIO Control knob 8. PRESET STATION Select Buttons
LD 445MP3 NA

Knowing your vehicle

1. POWER ON-OFF Control Knob
· The radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press the button to switch the power on. The LCD shows the radio frequency in the radio mode or CD/MP3 track in the CD/MP3 mode. To switch the power off, press the button again.
· Push the FM/AM, TAPE or CD/MP3 to turn on that function without pushing the Power ON-OFF control knob.
VOLUME Control
Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.
2. AUDIO Select Button
Pressing the AUDIO button changes the BASS, MID-RANGE, TREBLE, FADER and BALANCE mode.
The mode selected is shown on the display.

After selecting each mode, rotate the Audio control knob clockwise or counterclockwise.
BASS Control
To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.
MID-RANGE Control
To increase the MID-RANGE, rotate the knob clockwise, while to decrease the MID-RANGE, rotate the knob counterclockwise.
TREBLE Control
To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.
FADER Control
Turn the control knob clockwise to emphasize rear speaker sound (front speaker sound will be attenuated). When the control knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).

BALANCE Control

Rotate the knob clockwise to empha-

size right speaker sound (left speak-

er sound will be attenuated).

When the control knob is turned

counterclockwise, left speaker sound will be emphasized (right speaker

sound will be attenuated).

3. BAND Select Button

Pressing the FM/AM button changes 4

the AM, FM1 and FM2 bands. The

mode selected is shown on the display.

4. SCAN Button

When you press the button, frequen-

cy is changed and the next channel is received automatically.

To stay on a station, press the SCAN

button again.

5. EQ Button

Press the EQ button to select the

CLASSIC, POPS, ROCK, JAZZ and

OFF MODE for the desired tone

quality. Each press of the button

changes the display as follows;

3 111

Knowing your vehicle

6. AUTO SEEK Select Button (Automatic Channel Selection)

Press the AUTO SEEK select button. When the side is pressed, the

unit will automatically tune to the

next higher frequency and when the side is pressed, it will automati-

cally tune to the next lower frequen-

3 cy.

CLASSICPOPSROCKJAZZOFF
4

5 7. TUNE Select/Audio Control
Knob

6 Rotate the knob clockwise to

increase the frequency and turn the

knob counterclockwise to reduce the frequency.

8 8. PRESET STATION Select
Buttons
9 Six stations for AM, FM1 and FM2
respectively can be preset in the electronic memory circuit.

3 112

HOW TO PRESET STATIONS
Six AM and twelve FM stations may be programmed into the memory of the radio. Then, by simply pressing the AM/FM band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To program the stations, follow these steps:
· Press AM/FM selector to set the band for AM, FM1 and FM2.
· Select the desired station to be stored by seek or manual tuning.
· Determine the preset station select button you wish to use to access that station.
· Press and hold the station select button for more than 0.8 seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored in to the memory. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM stations per button.

· When completed, any preset station may be recalled by selecting AM, FM1 or FM2 band and the appropriate station button.
CAUTION
· Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
· Do not strike or allow anything to impact the audio system, damage to the system mechanisms could occur.

Knowing your vehicle

COMPACT DISC PLAYER (M455MP3) (IF EQUIPPED) - COMPATIBLE WITH MP3/WMA/AAC/WAVE

1. AUDIO/MP3 CD or AUX Select Button

2. TRACK UP/DOWN Button

3. FF/REW Button

4. REPEAT (RPT) Button

5. RANDOM (RDM) Button

6. BOOKMARK (MARK) Button

7. SCROLL Button

8. EQ Button

9. CD EJECT Button

10. CD SCAN Button

11. FILE SEARCH Knob

(TUNE Select Knob)

12. DIRECTORY SEARCH (DIR) Button

9
LD 445MP3 NA

3 113

Knowing your vehicle

1. AUDIO/MP3 CD or AUX

(Continued)

AUX 3.5mm STEREO MINI PLUG

Select Button

Please refer to the manual of CD-

AUDIO/MP3 CD Select · Insert the CD with the label facing

R/CD-RW recoder or CD-R/CDRW software for more information on finalization process.

upward.

· Depending on the recording sta-

2 · Insert the CD to start CD playback, tus, some CD-Rs/CD-RWs may

during radio operation.

not be played on this unit.

· If you press the CD/AUX button while a disc is in the CD deck, the

NOTICE

NOTICE
· If the AUX device is not connected,

CD player will begin playing even if Playback of MP3, AAC and WMA the radio or cassette player is file formats are supported. Load to

you cannot switch to AUX-IN mode.

being used.

play time for these formats may be · When the AUX device is discon-

· The CD/AUX player can be used longer due to the compressed nature when the ignition switch is in either of these discs.

nected while in AUX-IN mode, the unit automatically switches its

the "ON" or "ACC" position.

mode to last selected mode (CD

6 · Push the CD/AUX button to turn on AUX-IN Select

mode or RADIO mode).

that function without pushing the · When the AUX device (such as · The quality of sound may be defect-

Power ON-OFF control knob.

portable MP3 players) is connected to vehicle's AUX-IN terminal,

ed or distorted when the unit's EQ (BASS/MID/TREBLE) control and

NOTICE

you can switch to AUX-IN mode by AUX device's EQ control are both

8 9

· Do not stick paper or tape etc., on the label side or the recording side of any discs, as it may cause a malfunction.
· The unit can play a multi-session CD-R (recordable CD) and CDRW (rewritable CD) that consists of more than two sessions. (Continued)

pressing CD/AUX button.
· With a CD loaded and AUX device connected at the same time, this button switches between AUX-IN mode and CD mode.

enabled (not flat). When you want to use the unit's EQ control feature, disable the AUX device's EQ control feature, and vice versa. · When using a portable audio device connected to the power outlet, noise may occur during playback. If this happens, use the power source of the portable audio device.

3 114

Knowing your vehicle

2. TRACK UP/DOWN Button

· To repeat the music within selected 6. BOOKMARK (MARK) Button

· The desired track on the disc currently being played can be selected using the track number.

folder, press the RPT button for more than 0.8 seconds. To cancel, press it again. (MP3 CD only)

When the CD player unit is operating, the desired track on the disc can be bookmarked by using the MARK

· Press button once to skip forward to the beginning of the next track.

· If you do not release RPT operation when the track ends, it will automatically be replayed.

button. (MP3 CD only) · Press the MARK button for more

Press

within a second after

playback begins to quickly move

backward through a CD.

This process will be continued until you push the button again or turn the power OFF then ON.

than 0.8 seconds to bookmark the

desired track.

"M" will be displayed on the LCD

If you press after more than a second, it will take you to the beginning of the file you are now listening to.

5. RANDOM (RDM) Button
With random, you can listen to the tracks in random, rather than sequential order.

and "MEMORY(1~50)" will display for approximately five seconds with

beep sound.

To play a bookmarked track, press 5
the MARK button within 0.8 sec-

3. FF/REW Button

To use random, do the following:

onds and select the bookmarked

track to play.

If you want to fast forward or reverse through the compact disc track, push and hold the FF or REW button.
When you release the button, the compact disc player will resume playing.

· Press the RDM button to listen to recorded tracks in random sequence. Press RDM again to cancel or turn the power OFF then ON. The unit defaults to playing tracks in sequential order.

· To erase a bookmarked track, press the MARK button for more than 0.8 seconds. The unit will beep once when the bookmark is erased.

7 8

4. REPEAT (RPT) Button

· To listen to the music within the selected folder in random order,

NOTICE

· To repeat the track you are currently listening to, press the RPT button. To cancel, press it again.

press the RDM button within a sec- Tracks stored on Mark Memory will ond. To cancel, press it again or be automatically erased after you turn the power OFF then ON. (MP3 eject CDs that contain those tracks.

CD only)

3 115

Knowing your vehicle

7. SCROLL Button

10. CD SCAN Button

12. DIRECTORY SEARCH (DIR)

Press the button, and you can check · To playback the first 10 seconds of

Button

the file names with more than 16 characters on MP3 CD (max 34

each track, press the CD SCAN · You can move through the folder by

button more than 0.8 seconds.

pushing the DIR button to up ( )

characters.).

· To playback the first 10 seconds of and down( ).

2 The button doesn't work on file
names less than 16 characters.

each track in the selected folder, · After moving the desired folder, press the CD SCAN button within press the FILE SEARCH knob to

3 8. EQ Button

0.8 seconds. (MP3 CD only) · Press the CD SCAN button again

play back in the selected folder. If you do not press the FILE

Press the EQ button to select the
4 CLASSIC, POPS, ROCK, JAZZ and
OFF MODE for the desired tone

within 10 sec. when you have reached the desired track.

SEARCH knob within 5 seconds, the folder searching function will be released. It can not be operated in

quality. Each press of the button 11. FILE SEARCH Knob

changes the display as follows;

(TUNE Select Knob)

a single folder.

CLASSICPOPSROCKJAZZOFF

· You can skip the track (file) by turn-

ing the FILE SEARCH knob clock-

wise or counterclockwise.

9. CD EJECT Button When the button is pressed with a

CD loaded, the CD will eject.

After selecting the desired track (file), press the FILE SEARCH knob to playback the track (file).

8 Forcing to eject : To force to eject a If you do not press the FILE

CD, press this button for more than 3

seconds. (Do this only when a CD is jammed

SEARCH knob within five seconds, the search will stop.

and you can not eject it in the normal

way - e.g.) in case that you have

inserted 2 CDs by mistake)

3 116

Knowing your vehicle

1 2 3 4 5 6 7 8

damage to the compact disc

face could occur. (Continued)

3 117

Knowing your vehicle

RADIO AND AUDIO QUALITY/VOLUME CONTROL, EQ (HMP600) (IF EQUIPPED)

1,2. Power on /off and volume control button

3. Radio selection button

4. Scan Button

5. Automatic station selection button (Seek)

6. Manual station selection button (Tune)

7. Pre-set button

8. LCD Display

9. Bass control/ left, right audio control

9 LD 600 NA

3 118

Knowing your vehicle

1. Power on/off and volume

BSM button

· AM: Move by 9 KHz

control button

Push [BSM] button to start automatic (531540549····549540531)

When the ignition switch is on ACC or ON, push this button to power on. Push this button again to power off.
2. Volume control button

search from current station. The stations are memorized in 1~6 pre-set buttons from smallest station. Number 1 pre-set station will be on after the search and memory.

North America export (Columbian units FM move by 0.1 MHz)
· FM: Move by 0.2MHz
(87.587.787.9····87.987.7

1 2

Rotate this button clockwise to volume up and anti-clockwise to volume down.
3. Radio selection button (FM/AM)
Push [FM/AM] button for FM or AM radio. Each press will change FM1FM2AMFM1 and repeats.

5. Automatic station selection button (Seek)
Push [seek ] button, to increase the band and [seek ] button to decrease the band. It automatically finds available station. If the station is already memorized in pre-set memory, it will show the pre-set number.

87.5) · AM: Move by 10 KHz
(530540550····550540530)
7. Pre-set button (1~6) Push these buttons to listen to memorized stations. Push pre-set button for more than 1.5 seconds (with a beep) to memorize current station.

3 4 5 6

6. Manual station selection

4. Scan button

button (Tune)

Push this button to automatically Rotate this tune button clockwise 1 8. LCD display

select available stations and remains click to increase band 1 step and It indicates FM1/FM2/AM along with

for 5 seconds from current station. anti-clockwise to decrease.

current band, pre-set channel, FM

Push again to stay on current station.

stereo with "ST".

Regular export

· FM: Move by 0.1MHz

(87.587.687.7····87.787.6 87.5)

3 119

Knowing your vehicle

9. Bass control/ left, right audio control

TREBLE Rotate the volume button clockwise to increase

Push this button to select BASS MIDDLE TREBBLE FADER

BALANCE on LCD display screen.

high sound and anticlockwise to decrease high sound.

BASS

Rotate the volume button

BALANCE Rotate the volume button clockwise to enable right

clockwise to increase Bass sound and anti-

speakers and anti-clockwise to enable left speak-

clockwise to decrease Bass sound.

ers.

4 5

MIDDLE

Rotate the volume button clockwise to increase middle sound and anticlockwise to decrease Middle sound.

FADER

Rotate the volume button clockwise to increase back speaker sound and anti-clockwise to increase front speaker sound.

3 120

MP3 CDC (HMP600) (IF EQUIPPED)

Knowing your vehicle

1.CD loading slot

2.CD load button

3.CD eject button

4. LCD Display

5.CD/AUX selection button

6.CD change button

7,8.Fast Backward and Fast Forward button

9.Previous track automatic selection button

10. Next track automatic selection button

11.Repeat button

12.SCAN button

13.MARK button

14.RDM button

15.FILE search knob

16.SCROLL button

17.Directory search button

9
LD 600NA

3 121

Knowing your vehicle

1. CD loading slot

4. LCD display

AUX

3.5mm STEREO MINI PLUG

Push [LOAD] button to open CD slot. It indicates location of CD in CD

Please face printed side upward and deck. When loading and ejecting CD, gently push in. This CDC supports corresponding CD indicator number

only 12 cm CDs.

blinks.

2. CD load button

5. CD/AUX selection button

NOTICE

3 4 5 6 7

Pressing the "LOAD" button opens an empty tray of lowest order in the CDC deck. When a CD is loaded, the slot closes and the CD plays. To load CDs in all empty slots, press the "LOAD" button for more than 1.5 seconds. Be sure to insert only one CD into slot at a time. Then, lastly loaded CD is played. If you do not load CDs or press any button for 10 seconds after pressing the "LOAD" button, the LOAD function will be canceled.

CD Select When power is off while CD is loaded or radio/AUX is playing, push [CD] button to play CDC. When there is no available CD, "no disc" message will be indicated for 2 seconds and returns to previous mode.
AUX-IN Select · When the AUX device (such as
portable MP3 players) is connect-

· If the AUX device is not connected, you cannot switch to AUX-IN mode.
· When the AUX device is disconnected while in AUX-IN mode, the unit automatically switches its mode to last selected mode (CD mode or RADIO mode).
· The quality of sound may be defected or distorted when the unit's EQ (BASS/MID/TREBLE) control and AUX device's EQ con-

ed to vehicle's AUX-IN terminal, trol are both enabled (not flat).

8 3. CD eject button

you can switch to AUX-IN mode by pressing CD/AUX button.

Push button to eject the CD during CD playback. Push this button for more than 1.5 seconds to eject all the CDs. If CD number 3 is currently playing, ejecting order is 3,4,5,6,1,2.

· With a CD loaded and AUX device connected at the same time, this button switches between AUX-IN mode and CD mode.

When you want to use the unit's EQ control feature, disable the AUX device's EQ control feature, and vice versa.

3 122

Knowing your vehicle

6. CD change button
Push [DISC ] button to change to next CD (From CD 1 to CD 2). Push [DISC ] button to change to previous CD (From CD 2 to CD 1). If changer is not fully load, the changes will be next available CD.
7. Fast Backward button
During CD playback, push [REW] button to fast backward. For first 5 seconds 5X and 15X after 5 seconds. While the button is pressed sound is reduced to 12dB.
8. Fast Forward button
During CD playback, push [FF] button to fast forward. For first 5 seconds 5X and 15X after 5 seconds. While the button is pressed sound is reduced to 12dB.
9. Previous track automatic selection button
Push [TRACK ] button to go to beginning of currently playing track. Push again to move to beginning of previous track.

10. Next track automatic selection button
Push [SEEK ] button to go to move to beginning of next track.
11. Repeat button Push [RPT] button to repeat current track. Push again to disable.
12. SCAN button Push [SCAN] button to listen each track for 10 seconds. Push again to disable.
13. Book Mark button This is selecting desired tracks. Select desired tracks and push [MARK] button for more than 2 seconds. [M] symbol will be indicated and push for within 1 second to play [M] selected tracks.
14. RDM button This button randomly selects track.

NOTICE

Using CD-R/CD-RW, it may not be

played according to CD manufacturer, or how it was created. If it

does not play, please avoid using it.

It could cause problems on the system.

15. File search knob

Turn knob left and right to change

track. Push within 5 seconds to play selected track. It will return to cur-

rently playing track number after 5

seconds.

16. Scroll button

If the tile is too long for MP3/WMA

files, push [SCROLL] button to indi-

cate on LCD display screen.

17. Directory search button

For MP3/WMA files, if there are more

than 2 directories in a CD, push [Directory Search] buttons to search.

Select desired directory and use "File Search knob" to search file. Push "File Search knob" within 5 seconds otherwise it will go back to current playing track.

3 123

Ignition switch / 4-2

Starting the engine / 4-4

Manual transaxle / 4-5

Automatic transaxle / 4-6

Brake system / 4-11

Steering wheel / 4-18 Cruise control / 4-21

Driving your vehicle

Traction control system / 4-25 Instrument cluster / 4-28

Gauges / 4-29

Warnings and indicators / 4-31

Lighting / 4-39

Wipers and washers / 4-43 Defroster / 4-45

Hazard warning flasher / 4-46

Manual climate control system / 4-47

Windshield defrosting and defogging / 4-56

Theft-alarm system / 4-58

Driving your vehicle

IGNITION SWITCH

The warning lights can be checked

before the engine is started. This is

the normal running position after the

engine is started.

Do not leave the ignition switch ON if the engine is not running to prevent

battery discharge.

START

4 5

1LDA3012
Illuminated ignition switch Whenever a door is opened, the igni-

OUN036002
Ignition switch and anti-theft steering column lock

Turn the ignition key to the START position to start the engine. The engine will crank until you release the key; then it returns to the ON

tion switch will be illuminated for your Ignition switch position

position. The brake warning lamp

6 7 8

convenience, provided the ignition switch is not in the ON position. The light will go off approximately 30 seconds after closing the door or when the ignition switch is turned on.

LOCK The steering wheel locks to protect against theft. The ignition key can be removed only in the LOCK position. When turning the ignition switch to the LOCK position, push the key inward at the ACC position and turn the key toward the LOCK position.

can be checked in this position.
NOTICE
If difficulty is experienced in turning the ignition key to the START position, turn the steering wheel right and left to release resistance and then turn the key.

ACC (Accessory)

The steering wheel is unlocked and electrical accessories are operative.

WARNING - Ignition key
· Never turn the ignition switch to LOCK or ACC while the vehicle is moving. This would result in loss of directional control and braking function, which could cause an immediate accident.
· The anti-theft steering column lock is not a substitute for the parking brake. Before leaving the driver's seat, always make sure the shift lever is engaged in 1st gear for manual transaxle or P (Park) for automatic transaxle, set the parking brake fully and shut the engine off. Unexpected and sudden vehicle movement may occur if these precautions are not taken.
(Continued)

(Continued)
· Never reach for the ignition switch, or any other controls through the steering wheel while the vehicle is in motion. The presence of your hand or arm in this area could cause a loss of vehicle control, an accident and serious bodily injury or death.
· Do not place any movable objects around the driver's seat as they may move while driving, interfere with the driver and lead to an accident.

Driving your vehicle
1 2 3 4 5 6 7 8 9
43

Driving your vehicle

STARTING THE ENGINE

WARNING

3. Turn the ignition switch to START and hold it there until the engine

CAUTION

Always wear appropriate shoes

starts (a maximum of 10 seconds), Do not engage the starter for

when operating your vehicle. Unsuitable shoes (high heels,

then release the key. 4. In extremely cold weather (below

more than 10 seconds. If the engine stalls or fails to start,

ski boots,etc.) may interfere with your ability to use the

-18°C / 0°F) or after the vehicle has not been operated for several

wait 5 to 10 seconds before reengaging the starter. Improper

brake and accelerator pedal,

days, let the engine warm up with- use of the starter may damage

3 and the clutch (if equipped).

out depressing the accelerator.

it.

Whether the engine is cold or warm,

1. Make sure the parking brake is applied.

it should be started without depressing the accelerator.

The starter will not operate if:
· Manual Transaxle - the clutch pedal is not fully depressed.

5 6

2. Manual Transaxle - Depress the clutch pedal fully and shift the transaxle into Neutral. Keep the clutch pedal depressed while turning the ignition switch to the start

CAUTION
If the engine stalls while you are in motion, do not attempt to move the shift lever to the P

· Automatic Transaxle - the shift lever is NOT in the P (Park) or N (Neutral) position.

position. The starter will not oper- (Park) position. If traffic and ate if the clutch pedal is not fully road conditions permit, you may

depressed.

put the shift lever in the N

8 9

Automatic Transaxle - Place the transaxle shift lever in P (Park). Depress the brake pedal fully.
You can also start the engine

(Neutral) position while the vehicle is still moving and turn the ignition switch to the START position in an attempt to restart the engine.

when the shift lever is in the N

(Neutral) position.

Driving your vehicle

MANUAL TRANSAXLE (IF EQUIPPED)

CAUTION

Downshifting When you must slow down in heavy

To avoid premature clutch wear traffic or while driving up steep hills,

and damage, do not drive with your foot resting on the clutch

downshift before the engine starts to "labor''. Downshifting reduces the

pedal. Also, don't use the clutch to hold the vehicle stopped on

chance of stalling and gives better acceleration when you again need to

an upgrade, while waiting for a increase your speed. When the vehi-

traffic light, etc.

cle is traveling down steep hills, downshifting helps maintain safe

speed and prolongs brake life.

OLD046003N

WARNING - Manual

Manual transaxle operation

transaxle

The manual transaxle has five for- Before leaving the driver's seat,

ward gears.

always set the parking brake

Press the clutch pedal down fully fully and shut the engine off. while shifting, then release it slowly. Then make sure the transaxle is

A special safety feature prevents inadvertent shifting from 5 (Fifth) to R (Reverse). The gearshift lever must be returned to the neutral position before shifting into R (Reverse).

shifted into 1st gear on level or uphill ground or into R (Reverse) gear on downhill ground. Unexpected and sudden vehicle movement can occur if these precautions are

7 8

Make sure the vehicle is completely not followed in the order identistopped before shifting into R fied.

(Reverse).

Never operate the engine with the tachometer (rpm) in the red zone.

Driving your vehicle AUTOMATIC TRANSAXLE (IF EQUIPPED)

Lock release button

Prevents shift lever movement

without first depressing the button.
2

Depress the brake pedal and push the button when shifting.

The lock release button must be depressed while moving the shift lever.

The shift lever can be moved without depressing the lock release button.

OLD036019N

Driving your vehicle

Automatic transaxle operation
All normal forward driving is done with the shift lever in the D (Drive) position.

For smooth operation, depress the brake pedal when shifting from N (Neutral) to a forward or reverse gear.

CAUTION
· To avoid damage to your transaxle, do not accelerate the engine in R (Reverse) or

To move the shift lever from the P

any forward gear position with

(Park) position, the brake pedal must

WARNING - Automatic

the brakes on.

be depressed and the lock release button must be depressed.

transaxle
Before leaving the driver's seat, always make sure the shift lever

· When stopped on an upgrade, do not hold the vehicle stationary with engine power.

is in the P (PARK) position; then

Use the service brake or the

set the parking brake fully and

parking brake.

shut the engine off. Unexpected · Do not shift from N (Neutral)

and sudden vehicle movement can occur if these precautions

or P (Park) into D (Drive), or R (Reverse) when the engine is

are not followed in the order

above idle speed.

identified.

Driving your vehicle

Transaxle ranges

(Continued)

R (reverse)

P (park)
This position locks the transaxle and prevents the front wheels from rotat-

· Before leaving the driver's seat, always make sure the shift lever is in the P (PARK)

Use this position to drive the vehicle backward.

ing. Always come to a complete stop

position. Set the parking

CAUTION

2 before shifting into this position.

brake fully, shut the engine off and take the key with you.

Always come to a complete stop before shifting into or out of R

WARNING

Unexpected and sudden vehicle movement can occur if you

(Reverse); you may damage the transaxle if you shift into R

· Shifting into P (Park) while the

do not follow these precau- while the vehicle is in motion,

vehicle is in motion will cause the drive wheels to lock which

tions in the order specified.

except as explained in "Rocking the Vehicle", in this manual.

will cause you to lose control

of the vehicle.

CAUTION

· Do not use the P (Park) position in place of the parking brake. Always make sure the shift lever is latched in the P

The transaxle may be damaged if you shift into P (Park) while the vehicle is in motion.

(Park) position so that it cannot be moved unless the lock

release button is pushed in,

AND set the parking brake

fully.

(Continued)

Driving your vehicle

N (neutral)

3 (Third Gear)

L (Low)

With the gearshift in the N position, Move shift lever to this position for Move the shift lever to this position in

the wheels and transaxle are not towing a trailer during hill climbing. hard pulling situations and for climb-

locked. The vehicle will roll freely This position also provides engine ing steep grades.

even on the slightest incline unless braking when going down hills.

the parking brake or service brakes are applied.

CAUTION

2 (Second Gear)

Do not exceed the recommend-

D (drive)

Use 2 (Second Gear) for more power ed maximum speeds in 2 when climbing hills and for increased (Second Gear) or L (Low).

This is the normal forward driving braking when going down hills. This Operating the vehicle at speeds

position. The transaxle will automati- position also helps reduce wheel above the maximum recom- 4

cally shift through a 4-gear spin on slippery surfaces. When the mended, for 2 (Second Gear) or

sequence, providing the best fuel shift lever is placed in 2 (Second L (Low) may cause excessive

economy and power.

Gear), the transaxle will automatical- heat to develop which could

ly shift from first to second gear.

result in damage to or failure of

For extra power when passing another vehicle or climbing grades,

the automatic transaxle.

depress the accelerator fully, at

which time the transaxle will auto-

matically downshift to the next lower

gear.

Driving your vehicle

Moving up a steep grade from Shift lock system

Ignition key interlock system

a standing start

For your safety, the Automatic The ignition key cannot be removed

To move up a steep grade from a Transaxle has a shift lock system unless the shift lever is in the P standing start, depress the brake which prevents shifting the transaxle (Park) position. If the ignition switch

pedal, shift the shift lever to D out of P (Park) unless the brake is in any other position, the key can-

(Drive). Select the appropriate gear pedal is depressed.

not be removed.

depending on load weight and steep- To shift the transaxle out of P (Park):

ness of the grade, and release the parking brake. Depress the accelera-

1. Depress and hold the brake pedal.

tor gradually while releasing the 2. Start the engine or turn the ignition

4 service brakes.

to the ON position. 3. Depress the lock release button

and move the shift lever.

When the ignition switch is in the

LOCK position, the transaxle cannot

be shifted from P (Park).
6

WARNING

Always fully depress the brake

pedal before and while shifting

out of the P (Park) position into another position to avoid inad-

vertent motion of the vehicle

which could injure persons in or

around the car.

4 10

Driving your vehicle

BRAKE SYSTEM

Power brakes

In the event of brake failure

Your vehicle has power-assisted If service brakes fail to operate while

WARNING - Brakes

brakes that adjust automatically the vehicle is in motion, you can · Do not drive with your foot

through normal usage.

make an emergency stop with the

resting on the brake pedal.

In the event that the power-assisted brakes lose power because of a stalled engine or some other reason, you can still stop your vehicle by applying greater force to the brake pedal than you normally would. The

parking brake. The stopping distance, however, will be much greater than normal.
WARNING - Parking brake

This will create abnormal high brake temperatures, excessive brake lining and pad wear, and increased stopping distances.
· When descending a long or

2 3

stopping distance, however, will be Applying the parking brake

longer.

while the vehicle is moving at

steep hill, shift to a lower gear and avoid continuous applica-

When the engine is not running, the reserve brake power is partially depleted each time the brake pedal is applied. Do not pump the brake pedal when the power assist has been interrupted.

normal speeds can cause a sudden loss of control of the vehicle. If you must use the parking brake to stop the vehicle, use great caution in applying the brake.

tion of the brakes. Continuous

brake application will cause the brakes to overheat and

could result in a temporary

loss of braking performance.

(Continued)

Pump the brake pedal only when

necessary to maintain steering con-

trol on slippery surfaces.

4 11

Driving your vehicle

(Continued)

Disc brakes wear indicator

CAUTION

· Wet brakes may result in the Your vehicle has disc brakes.

To avoid costly brake repairs, do

vehicle not slowing down at When your brake pads are worn and not continue to drive with worn the usual rate and pulling to it's time for new pads, you will hear a brake pads.

one side when the brakes are high-pitched warning sound from

applied. Applying the brakes your front brakes or rear brakes (if

lightly will indicate whether equipped). You may hear this sound

they have been affected in this come and go or it may occur when-

WARNING - Brake wear

way. Always test your brakes ever you depress the brake pedal.

This brake wear warning sound

in this fashion after driving Please remember that some driving means your vehicle needs serv-

through deep water. To dry the brakes, apply them lightly

conditions or climates may cause a brake squeal when you first apply (or

ice. If you ignore this audible warning, you will eventually lose

while maintaining a safe for- lightly apply) the brakes. This is nor- braking performance, which

ward speed until brake performance returns to normal.

mal and does not indicate a problem with your brakes.

could lead to a serious accident.

CAUTION

Always replace brake pads as

complete front or rear axle sets.

4 12

Driving your vehicle

NOTICE

If you depress the release button

without pulling up the parking brake lever, you will not be able to

release the parking brake.

2
WARNING - Parking brake

· To prevent unintentional 3
movement when stopped and

OLD036030

OLD036031

leaving the vehicle, do not use the gearshift lever in place of

Parking brake

To release the parking brake, first

the parking brake. Set the

To engage the parking brake, first apply the foot brake and then without pressing the release button in, pull the parking brake lever up as far as possible. In addition it is recommended that when parking the vehicle on a gradient, the shift lever should be positioned in the appropriate low gear on manual transaxle vehicles or in the P (Park) position on automatic transaxle vehicles.

apply the foot brake and pull up the parking brake lever slightly.
Secondly, depress the release button and lower the parking brake lever while holding the button.

parking brake AND make sure the gearshift lever is securely positioned in 1st (First) gear or R (Reverse) for manual transaxle equipped vehicles and in P (Park) for automatic transaxle equipped vehicles.
· Never allow a person who is unfamiliar with the vehicle or children to touch the parking brake. If the parking brake is released unintentionally, seri-

5 6 7 8 9

CAUTION

ous injury may occur.

Driving with the parking brake applied will cause excessive brake pad and brake rotor wear.

4 13

Driving your vehicle

If the brake warning light remains on Parking on curbed streets

after the parking brake is released, there may be a malfunction in the brake system. Immediate attention is necessary.

· When parking your vehicle on an uphill grade, park as close to the curb as possible and turn the front wheels away from the curb so that

If at all possible, cease driving the vehicle immediately. If that is not pos-

the front wheels will contact the curb if the vehicle moves back-

sible, use extreme caution while ward.

3 4

W-75

operating the vehicle and only continue to drive the vehicle until you can reach a safe location or repair shop.

· When parking your vehicle on a downhill grade, park as close to the curb as possible and turn the front wheels toward the curb so that the

Check the brake warning light by

front wheels will contact the curb if

turning the ignition switch ON (do not start the engine). This light will be

the vehicle moves forward.

illuminated when the parking brake is

6 applied with the ignition switch in the
START or ON position.

Before driving, be sure the parking brake is fully released and the brake

warning light is off.

4 14

Driving your vehicle

Anti-lock brake system (ABS) (if equipped)
WARNING - ABS Brakes
Your ABS is not a substitute for good driving judgement. You can still have an accident. In fact, your ABS system will probably not be able to prevent an accident in the following driving conditions:
· Dangerous driving, such as neglecting safety precautions, speeding, or driving too close to the vehicle in front of you.
· Driving at high speed in situations providing considerably less traction, such as wet conditions where hydroplaning could occur.
(Continued)

(Continued)

The ABS system continuously senses the speed of the wheels. If the

· Driving too fast on poor road wheels are going to lock, the ABS

surfaces. The ABS is designed to improve maximum braking

system repeatedly modulates the hydraulic brake pressure to the

effectiveness on typical high- wheels.

ways and roads in good condition. On poor road surfaces in poor condition, the ABS may actually reduce braking effectiveness.

When you apply your brakes under conditions which may lock the wheels, you may hear a "tik-tik'' sound from the brakes, or feel a corresponding sensation in the brake

2 3

pedal. This is normal and it means 4

your ABS system is active.

In order to obtain the maximum benefit from your ABS system in an

emergency situation, do not attempt

to modulate your brake pressure and 6
do not try to pump your brakes.

Press your brake pedal as hard as
possible or as hard as the situation 7

warrants and allow the ABS system

to control the force being delivered to the brakes.

4 15

Driving your vehicle

· Even with the anti-lock brake sys-

tem, your vehicle still requires suf-

ficient stopping distance. Always

maintain a safe distance from the

vehicle in front of you.

· Always slow down when cornering. The anti-lock brake system cannot

prevent accidents resulting from

excessive speeds.

· On loose or uneven road surfaces,

operation of the anti-lock brake system may result in a longer stop-

ping distance than for vehicles

equipped with a conventional brake system.

4 16

ABS
W-78
CAUTION
· If the ABS warning light is on and stays on, you may have a problem with the ABS system. In this case, however, your regular brakes will work normally.
· The ABS warning light will stay on for approximately 3 seconds after the ignition switch is ON. During that time, the ABS will go through self-diagnosis and the light will go off if everything is normal. If the light stays on, you may have a problem with your ABS system. Contact an authorized Kia dealer as soon as possible.

CAUTION
· When you drive on a road having poor traction, such as an icy road, and operate your brakes continuously, the ABS will be active continuously and the ABS warning light may illuminate. Pull your car over to a safe place and stop the engine.
· Restart the engine. If the ABS warning light is off, then your ABS system is normal. Otherwise, you may have a problem with the ABS. Contact an authorized Kia dealer as soon as possible.

NOTICE
When you jump start your vehicle because of a drained battery, the engine may not run as smoothly and the ABS warning light may turn on at the same time. This happens because of the low battery voltage. It does not mean your ABS is malfunctioning. · Do not pump your brakes! · Have the battery recharged before
driving the vehicle.

Driving your vehicle
1 2 3 4 5 6 7 8 9
4 17

Driving your vehicle

STEERING WHEEL

Power steering

CAUTION

NOTICE

1 2 3 4 5

Power Steering uses energy from the engine to assist you in steering the vehicle. If the engine is off or if the power steering system becomes inoperative, the vehicle may still be steered, but it will require increased steering effort.
Should you notice any change in the effort required to steer during normal vehicle operation, have the power steering checked by an Authorized Kia Dealer.

· Never hold the steering wheel against a stop (extreme right or left turn) for more than 5 seconds with the engine running. Holding the steering wheel for more than 5 seconds in either position may cause damage to the power steering pump.
· If the power steering drive belt breaks or if the power steering pump malfunctions, the steering effort will greatly increase.

If the vehicle is parked for extended periods outside in cold weather (below -10 °C/14 °F), the power steering may require increased effort when the engine is first started. This is caused by increased fluid viscosity due to the cold weather and does not indicate a malfunction. When this happens, increase the engine RPM by depressing accelerator until the RPM reaches 1,500 rpm then release or let the engine idle for two or three minutes to warm up the fluid.

4 18

Driving your vehicle

Tilt steering (if equipped)

A tilt steering wheel allows you to

WARNING

adjust the steering wheel before you drive. You can also raise it to the

· Never adjust the angle of steering wheel while driving.

highest level to give your legs more

You may lose your steering

room when you exit and enter the vehicle.

control and cause severe personal injury or accidents.

· After adjusting, push the

The steering wheel should be positioned so that it is comfortable for you to drive, while permitting you to see the instrument panel warning

steering wheel both up and down to be certain it is locked in position.

OLD026076

lights and gauges.

To change the steering wheel angle,

pull down (1) the lock release lever, adjust the steering wheel to the

desired angle (2), then pull up the

lock-release lever to lock the steering 6
wheel in place.

Be sure to adjust the steering wheel to the desired position before driving.

4 19

Driving your vehicle

CAUTION

· To sound the horn, press the

area indicated by the horn symbol on your steering

wheel (see illustration). The

horn will operate only when

this area is pressed.

· Do not strike the horn severely to operate it, or hit it with your

fist. Do not press on the horn

OLD026077

with a sharp-pointed object.

Horn

5 To sound the horn, press the horn
symbol on your steering wheel.

Check the horn regularly to be sure it operates properly.

4 20

Driving your vehicle

CRUISE CONTROL (IF EQUIPPED)

The cruise control system allows you

2. Accelerate to the desired speed,

to program the vehicle to maintain a

which must be more than 40 km/h

constant speed without resting your

(24 mph).

foot on the accelerator pedal.

This system is designed to function above approximately 40 km/h (24 mph).

WARNING
If the cruise control is left on, 2
(CRUISE indicator light in the

WARNING - Cruise

instrument cluster illuminated) the cruise control can be

control

switched on accidentally. Keep

Do not use the cruise control feature under the following conditions:
· Heavy or unsteady traffic

1LDN4024
To set cruise control speed:
1. Push the CRUISE ON/OFF button on the steering wheel, to turn the

the cruise control system off (CRUISE indicator light OFF) when cruise control is not in use.

4 5

· Slippery or winding roads · Situations that involve varying

system on. The CRUISE indicator light in the instrument cluster will

speeds

illuminate.

· Pay particular attention during

the down-hill driving with

cruise control system as the vehicle speed can be

increased gradually.

4 21

Driving your vehicle

To turn cruise control off, do one of the following:

· Push the CRUISE ON-OFF button (the CRUISE indicator light in the

instrument cluster will go OFF).

· Turn the ignition off.

Both of these actions cancel cruise

control operation. If you want to resume cruise control operation,

repeat the steps provided in "To Set

1LDN4025

1LDN4025A Cruise Control Speed" on the previ-

3. Push down the SET/COAST switch, To cancel cruise control, do

ous page.

and release it at the speed you one of the following:

want. The "SET" indicator light in the instrument cluster will illuminate.

· Press the brake pedal.

Release the accelerator at the · Shift into N (Neutral).

same time. The desired speed will · Pull the CANCEL switch.

automatically be maintained.

Each of these actions will cancel

The SET function cannot be activated cruise control operation (the "SET"

until approximately 2 seconds after the indicator light in the instrument clus-

8 CRUISE ON-OFF button has been ter will go OFF), but it will not turn the

engaged.

system off. If you wish to resume

On a steep grade, the vehicle may cruise control operation, push up the momentarily slow down while going RES/ACC switch located on your

downhill.

steering wheel. You will return to your

previously preset speed.

4 22

Driving your vehicle

To temporarily accelerate with the cruise control on

If you want to speed up temporarily when the cruise control is on,

depress the accelerator pedal.

Increased speed will not interfere with cruise control operation or

change the set speed.

To return to the set speed, take your

foot off the accelerator.

1LDN4026
To increase cruise control set speed:
Follow either of these procedures:

1LDN4025

To decrease the cruising

speed:

Follow either of these procedures:

· Push up the RES/ACC switch and hold it. Your vehicle will accelerate. Release the switch at the speed you want.
· Push up the RES/ACC switch and release it immediately. The cruising speed will increase 1.6 km/h (1 mph) by one touch and will be memorized to the reset speed.

· Push down the SET/COAST switch and hold it. Your vehicle will gradu-

ally slow down. Release the switch
at the speed you want to maintain. 7

· Push down the SET/COAST switch

and release it immediately. The cruising speed will decrease 1.6

km/h (1 mph) by one touch and will

be memorized to the reset speed. 9

4 23

Driving your vehicle

1LDN4026

To resume cruising speed at

5 more than 40 km/h (24 mph):

If any method other than the

CRUISE ON-OFF switch was used to cancel cruising speed and the sys-

tem is still activated, the most recent

set speed will automatically resume when the RES/ACC switch is pushed

up.
8 It will not resume, however, if the

vehicle speed has dropped below

9 40km/h (24 mph).

4 24

Driving your vehicle

TRACTION CONTROL SYSTEM (IF EQUIPPED)

TCS operation

TCS ON condition

When operating

OLD026118
The Traction Control System (TCS) helps the vehicle accelerate on slippery road surfaces by preventing the drive wheels from spinning excessively. It also provides improved driving force and steering.

· When the ignition is turned ON, TCS and TCS OFF

When the TCS is in opera-
TCS tion, TCS indicator light

indicator light illuminate for

blinks.

approximately 3 seconds, then TCS is turned on.

· When the traction control 2
system is operating prop-

· Press the TCS button to turn TCS off. (TCS OFF

erly, you can feel a slight pulsation in the vehicle.

indicator will illuminate). To

This is only the effect of

turn the TCS on, press the TCS button (TCS OFF

brake control and indicates nothing unusual.

indicator light will go off). · When starting the engine,

· When moving out of mud or driving on a slippery

you may hear a slight tick-

road, pressing the accel-

ing sound. This is the TCS performing an automatic

erator pedal may not cause the engine rpm

system self-check and does

(revolutions per minute) to

not indicate a problem.

increase.

4 25

Driving your vehicle

TCS operation off

TCS OFF state

TCS OFF

· To cancel TCS operation, press the TCS button (TCS OFF indicator light

illuminates).

TCS indicator light (blinks)
TCS
TCS OFF indicator light (comes on)

WARNING
The Traction Control System is only a driving aid; use precautions for safe driving by slowing down on curved, snowy, or icy roads.

· If the ignition switch is

turned to LOCK position when TCS is off, TCS

TCS OFF

remains off. Upon restart-

ing the engine, the TCS will Indicator light automatically turn on

again.

When ignition switch is turned to ON,

the indicator light illuminates, then goes off if TCS system is operating

normally.

The TCS indicator light blinks when-

ever TCS is operating.

TCS OFF indicator light comes on

when either the TCS is turned off

with the button, or TCS fails to operate when turned on.

4 26

Driving your vehicle

TCS OFF usage

NOTICE

When driving

· When measuring the vehicle speed

WARNING - TCS

· It's a good idea to keep the TCS turned on for daily driving whenever possible.
· To turn TCS off while driving, press the TCS button while driving on a flat road surface.
Never press TCS button while TCS is operating (TCS indicator light blinks).

with a Chassis dynamometer, make sure the TCS is turned off (TCS OFF light illuminated). If the TCS is left on, it may prevent the vehicle speed from increasing, and cause a false diagnosis of a faulty speedometer. · Turning the TCS off does not affect ABS or brake system opera-

Never press the TCS button while TCS is operating.
If the TCS is turned off while TCS is operating, the vehicle may slip out of control.
To turn TCS off while driving, press the TCS button while driving on a flat road surface.

1 2 3

If TCS is turned off while TCS is tion.

operating, the vehicle may slip out of

control.

4 27

Driving your vehicle INSTRUMENT CLUSTER
1 2 3 4 5 6 7 8 9
4 28

1. Tachometer 2. Turn signal indicators 3. Speedometer 4. Engine temperature gauge 5. Warning and indicator lights 6. Odometer / Tripmeter 7. Shift position indicator
(Automatic transaxle only) 8. Fuel gauge
OLD026090C-C

Driving your vehicle

GAUGES Speedometer
The speedometer indicates the forward speed of the vehicle.
Odometer/Tripmeter You can choose the odometer, tripmeter A or tripmeter B by pressing the TRIP button.

CAUTION

Do not operate the engine with-

in the tachometer's RED ZONE.

This may cause severe engine

damage.

Odometer The odometer indicates the total dis-

OLD026200L

tance the vehicle has been driven. Tachometer

The tachometer indicates the

Tripmeter

approximate number of engine revo-

TRIP A: Tripmeter A TRIP B: Tripmeter B

lutions per minute (rpm). Use the tachometer to select the cor-

The tripmeter indicates the distance of individual trips selected by the

rect shift points and to prevent lugging and/or over-revving the engine.

driver. Tripmeter A and B can be The tachometer pointer may move

reset to 0 by pressing the TRIP but- slightly when the ignition switch is in ton for 1 second or more, and then ACC or ON position with the engine

releasing.

OFF. This movement is normal and

will not affect the accuracy of the

tachometer once the engine is run-

ning.

4 29

Driving your vehicle

Engine temperature gauge

Fuel gauge

This gauge shows the temperature The fuel gauge indicates the approx-

of the engine coolant when the igni- imate amount of fuel remaining in the

tion switch is ON.

fuel tank.

Do not continue driving with an over- Fuel tank capacity - 55 litres (14.52

2 heated engine. If your vehicle over- US gal. ).

heats, refer to "Overheating" in the The fuel gauge is supplemented by a

Index.
3

low fuel warning light, which will illuminate when the fuel level has

CAUTION

dropped to about 8.5 liters (2.25 US

4 If the gauge pointer moves gal.).

OLD026204N

beyond the normal range area

toward the "H" position, it indicates overheating that may

damage the engine.

Instrument panel illumination
When the vehicle's parking lights or headlights are on, rotate the illumination control knob to adjust the instrument panel illumination intensity.

4 30

Driving your vehicle

WARNINGS AND INDICATORS

Warning lights / audible indi- Anti-lock brake sys-

In this case, your ABS system and

cators

tem (ABS) warning

ABS

regular brake system may not work

Checking operation
All warning lights are checked by turning the ignition switch ON (do not

light (if equipped)
This light illuminates if the key is turned to ON and goes off in approx-

normally. Have the vehicle checked by an Authorized Kia Dealer as soon as possible.

start the engine). Any light that does imately 3 seconds if the system is not illuminate should be checked by operating normally.

WARNING

an Authorized Kia Dealer.

If the light stays on, you may have a If the both ABS and Brake warn-

After starting the engine, check to problem with your ABS system. ing lights are ON and stay ON,

make sure that all warning lights are Contact an authorized Kia dealer as your vehicle's brake system will

off. If any are still on, this indicates a soon as possible. situation that needs attention. When

not work normally. So you may experience an unexpected and

releasing the parking brake, the Electronic brake force

brake system warning light should go distribution (EBD)

ABS

off. The fuel warning light will stay on if the fuel level is low.

system warning light (if equipped)

dangerous situation during sud-
den braking. In this case, avoid 5
high speed driving and abrupt
braking. Have your vehicle
checked by Authorized Kia 6

If two warning lights illumi-

Dealer as soon as possible.

nate at the same time while driving, your vehicle

has a problem with ABS

and EBD system.

4 31

Driving your vehicle

Engine oil pressure warning

Charging system warning

Safety belt warning

1 This warning light indicates the This warning light indicates a mal- If the driver's lap/shoulder belt is not

engine oil pressure is low.

function of either the generator or fastened when the ignition switch is

2 If the warning light illuminates while electrical charging system.

turned ON, the safety belt warning

driving:

If the warning light comes on while light and chime will activate for about

1. Drive safely to the side of the road the vehicle is in motion:

and stop.

1. Drive to the nearest safe location.

6 seconds. And if the lap/shoulder belt is fastened when the ignition switch is turned ON, the safety belt

2. With the engine off, check the 2. With the engine off, check the gen- warning light will blink for about 6 engine oil level. If the level is low, erator drive belt for looseness or seconds.

add oil as required.

breakage.

If the lap/shoulder belt is unfastened

If the warning light remains on after 3. If the belt is adjusted properly, a while the lap/shoulder belt is fasadding oil or if oil is not available, call problem exists somewhere in the tened with the ignition switch ON, the

an Authorized Kia Dealer.
6

electrical charging system. Have safety belt warning light will blink for an Authorized Kia Dealer correct about 6 seconds and if the vehicle

CAUTION
7 If the engine is not stopped
immediately, severe damage

the problem as soon as possible.

speed exceeds 10 km/h the safety belt warning light and chime will activate until it is fastened.

could result.

4 32

Driving your vehicle

Rear window defroster indicator (if equipped)

Shift pattern indicators (if equipped)

Parking brake & brake fluid warning

This light comes on when the rear defroster switch is depressed to remove the frost on the rear glass.

The individual indicators illuminate to show the automatic transaxle shift lever selection.

Parking brake warning
This light is illuminated when the parking brake is applied with the ignition switch in the START or ON posi-

1 2

Press the switch again to shut off the

tion. The warning light should go off

defroster when the frost is removed. Door ajar warning The rear window defroster will auto-

when the parking brake is released.

matically turn off after 20 minutes.

Low brake fluid level warning

It will also turn off whenever you remove the ignition key.

This warning light illuminates when a door is not closed securely with the ignition in any position.

If the warning light remains on, it may indicate that the brake fluid level in the reservoir is low.

4 5

Immobilizer indicator (if equipped)

If the warning light remains on:

1. Drive carefully to the nearest safe location and stop your vehicle.

2. With the engine stopped, check

This light illuminates when the immo-

the brake fluid level immediately 7

bilizer key is inserted and turned to

and add fluid as required. Then

the ON position to start the engine. If this light turns off or blinks when

check all brake components for fluid leaks.

the ignition switch is in the ON posi-

tion before starting the engine, have

the system checked by an authorized

Kia Dealer.

4 33

Driving your vehicle

3. Do not drive the vehicle if leaks Trunk lid open

Headlight high beam

are found, the warning light warning (if equipped)

indicator

remains on or the brakes do not

operate properly. Have it towed to any Authorized Kia Dealer for a This warning light activates when the This indicator illuminates when the

brake system inspection and nec- trunk is not closed securely.

headlights are on and in the high

essary repairs.

Stop the vehicle and close the lid.

beam position or when the turn sig-

nal lever is pulled into the Flash-to-

3 To check bulb operation, check Low fuel level

Pass position.

whether the parking brake and brake warning

fluid warning light illuminates when the ignition switch is in the ON posi-

Front fog light indicator (if equipped)

tion.

This warning light indicates the fuel

tank is nearly empty. The warning light will come on when the fuel level This light comes on when the front

WARNING

has dropped to about 8.5 liters (2.25 fog lights are ON.

6 Driving the vehicle with a warn- US gal.). Refuel as soon as possible.

ing light on is dangerous. If the

Low washer fluid level

brake warning light remains on, have the brakes checked and

warning indicator

repaired immediately by an
8 Authorized Kia Dealer.

This warning light indicates the washer fluid reservoir is near empty.

Refill the washer fluid as soon as

possible.

4 34

Driving your vehicle

Malfunction indicator (if equipped)
CHECK

CAUTION
· Prolonged driving with the

Air bag warning (if equipped)

This indicator light is part of the

Emission Control System Malfunction Indicator Light

This warning light will blink or illumi-

Engine Control System which monitors various emission control system components. If this light illuminates

( ) CHECK illuminated may cause nate for approximately 6 seconds
damage to the emission con- each time you turn the ignition switch 2
trol systems which could to the ON position.

while driving, it indicates that a potential problem has been detected

effect drivability and/or fuel economy.

If this indicator does not go out, or if it illuminates while the vehicle is

somewhere in the emission control · If the Emission Control System being driven, see an Authorized Kia

system.

Malfunction Indicator Light Dealer for immediate service.

Generally, your vehicle will continue

( ) CHECK begins to flash ON and

to be drivable and will not need tow-

OFF, potential catalytic con-

ing, but have the system checked by

verter damage is possible

an Authorized Kia Dealer as soon as

which could result in loss of

possible.

engine power. Have the Engine Control System inspected as

NOTICE
A loose fuel filler cap may cause the

soon as possible by an Authorized Kia Dealer.

On Board Diagnostic System

Malfunction Indicator Light ( ) CHECK

in the instrument panel to illuminate

unnecessarily. Always make sure

that the fuel filler cap is tight.

4 35

Driving your vehicle

Auto cruise indicator

TCS indicator

(if equipped)

(Traction Control

TCS

1 CRUISE indicator

System) (if equipped) CRUISE

TCS OFF indicator (if equipped)

TCS OFF

The TCS indicator will illuminate The TCS OFF indicator will illuminate

when the ignition switch is turned when the ignition switch is turned The indicator light illuminates when ON, but should go off after approxi- ON, but should go off after approxi-

the cruise control system is enabled. mately 3 seconds. When the TCS is mately 3 seconds. To switch to TCS

on, it monitors the driving conditions OFF mode, press the TCS button.

SET indicator

and under normal driving conditions, The TCS OFF indicator will illuminate

SET

the TCS light will remain off. When a indicating the TCS is deactivated. slippery or low traction condition is If this indicator stays on in the TCS

encountered, the TCS will operate, ON mode, the TCS may have a mal-

The indicator light illuminates when and the TCS indicator will blink to function. Take your car to the author-

the cruise function switch (COAST/ indicate the TCS is operating.

ized Kia dealer and have the system

SET or RES/ACCEL) is ON.

checked.

4 36

Driving your vehicle

Key reminder warning chime Low tire pressure

If the driver's door is opened and the ignition key is left in with the ignition switch in the LOCK or ACC position, the key reminder warning chime will sound. This is to prevent you from locking your keys in the vehicle.

telltale (if equipped)
The low tire pressure telltale comes on for 3 seconds after the ignition switch is turned to the ON position. If the warning light does not come

WARNING - Low tire pres-
sure
Significantly low tire pressure makes the vehicle unstable and can contribute to loss of vehicle control and increased braking distances.

1 2

on, or continuously remains on after coming on for about 3 seconds when you turned the ignition switch to the ON position, the Tire Pressure Monitoring System is not working

Continued driving on low pressure tires will cause the tires to overheat and fail.

3 4

properly. If this occurs, have your

vehicle checked by an authorized

KIA dealer as soon as possible.

This warning light will also illuminate if one or more of your tires is signifi-

cantly under-inflated. You should

stop and check your tires as soon as

possible. If the warning light illumi-

nates while driving, reduce vehicle speed immediately and stop the

vehicle. Avoid hard braking and over-

correcting at the steering wheel. Inflate the tires to the proper pres-

sure as indicated on the vehicle's tire

information placard.

4 37

Driving your vehicle

TPMS (Tire pressure monitoring system) TPMS

WARNING - Safe stopping

malfunction indicator

· The TPMS cannot alert you to

1 (if equipped)

severe and sudden tire dam-

TPMS malfunction indicator comes on for 3 seconds after the ignition switch is turned to the ON position. If

age caused by external factors.
· If you feel any vehicle instabil-

the warning light does not come on,

ity, immediately take your foot

3 or continuously remains on after
coming on for about 3 seconds when

off the accelerator, apply the brakes gradually and with

you turned the ignition switch to the ON position, the Tire Pressure

light force, and slowly move to a safe position off the road.

Monitoring System is not working

porperly. If this occurs, have your vehicle checked by an authorized

KIA dealer as soon as possible.

6 The warning light also comes on and

stays on when there is a problem

with the Tire Pressure Monitoring System.

If this happens, the system may not
8 monitor the tire pressure. Have the
system checked by an authorized
9 KIA dealer as soon as possible.

4 38

Driving your vehicle

LIGHTING

Battery saver function

· The purpose of this feature is to

prevent the battery from being discharged. The system automatically

turns off the small light when the

driver removes the ignition key and opens the driver- side door.

· With this feature, the parklight will

be turned off automatically if the

driver parks on the side of road at

night.

If necessary, to keep the lights on when the ignition key is removed,

Lighting control

OLD026101C

OLD026102

Parklight position ( )

perform the following :

The light switch has a Headlight and When the light switch is in the park- 5

1) Open the driver-side door.

a Parklight position.

light position (1st position), the tail,

2) Turn the parklights OFF and ON again using the light switch on the

To operate the lights, turn the knob at the end of the control lever to one of

position, license and instrument panel lights are ON.

steering column.

the following positions: OFF position

Parklight position

Headlight position

4 39

Driving your vehicle

OLD026103

OLD026106

OLD026105

Headlight position ( )

High - beam operation

Flashing headlights

5 When the light switch is in the head- To turn on the high beam headlights, To flash the headlights, pull the lever

light position (2nd position) the head, push the lever away from you. Pull it towards you. It will return to the nor-

6 7

tail, position, license and instrument panel lights are ON.

back for low beams.
The high-beam indicator will light when the headlight high beams are switched on.

mal (low-beam) position when released. The headlight switch does not need to be on to use this flashing feature.

To prevent the battery from being

discharged, do not leave the lights on for a prolonged time while the

engine is not running.
9

4 40

Driving your vehicle

Lane change signals (B)

To signal a lane change, move the

turn signal lever slightly and hold it in

position. The lever will return to the

OFF position when released.

If an indicator stays on and does not flash or if it flashes abnormally, one

of the turn signal bulbs may be

burned out and will require replace-

ment.

Turn signals (A)

1LDN2107 NOTICE

OLD026115

Front fog light (if equipped)

The ignition switch must be on for the turn signals to function. To turn on the turn signals, move the lever up or down. Green arrow indicators on the

If an indicator flash is abnormally quick or slow, bulb may be burned out or have a poor electrical connection in the circuit.

Fog lights are used to provide improved visibility and avoid accidents when visibility is poor due to fog, rain or snow etc. The fog lights

5 6

instrument panel indicate which turn

will turn on when fog light switch (1)

signal is operating. They will selfcancel after a turn is completed. If

is turned to ON after the headlight switch is turned on.

the indicator continues to flash after a turn, manually return the lever to the OFF position.

To turn off the fog lights, turn the switch to OFF.

4 41

Driving your vehicle

CAUTION

Daytime running light (if equipped)

1 2 3

When in operation, the fog lights consume large amounts of vehicle electrical power. Only use the fog lights when visibility is poor or unnecessary battery and generator drain could occur.

Daytime Running Lights (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, and it is especially helpful after dawn and before sunset.

The DRL system will make your

headlights turn OFF when: 1. The head light switch is ON.

2. The parking brake engaged. 3. Engine stops.

4 42

Driving your vehicle

WIPERS AND WASHERS

LO : Normal wiper speed HI : Fast wiper speed

CAUTION

: For a single wiping cycle, push the lever forward and release it with the lever in the OFF position. The wipers will operate continuously if the lever is

· To prevent possible damage to the wipers or windshield, do not operate the wipers when the windshield is dry.
· To prevent damage to the

1 2

pushed upward and held.

wiper blades, do not use gaso-

line, kerosene, paint thinner, or other solvents on or near

NOTICE

them.

OLD026108N If there is heavy accumulation of · To prevent damage to the 4

Windshield wipers
Operates as follows when the ignition switch is turned ON.

snow or ice on the windshield, defrost the windshield for about 10 minutes, or until the snow and/or ice is removed before using the wind-

wiper arms and other compo-

nents, do not attempt to move the wipers manually.

OFF : Wiper is not in operation

shield wipers to ensure proper oper-

INT : Wiper operates intermittently ation.

at the same wiping intervals. Use this mode in a light rain or

mist. To vary the speed set-

ting, turn the speed control knob (1).

4 43

Driving your vehicle

If the washer does not work, check

the washer fluid level. If the fluid level

is not sufficient, you will need to add

appropriate non-abrasive windshield

washer fluid to the washer reservoir.

The reservoir filler neck is located in the front of the engine compartment

on the passenger side.

3
CAUTION

OLD026109N
Windshield washers

To prevent possible damage to the washer pump, do not operate the washer when the fluid

OLD027110N
Rear window wiper and wash-

5 In the OFF position, pull the lever reservoir is empty.

er switch (if equipped)

gently toward you to spray washer

The rear window wiper and washer

6 7 8

fluid on the windshield and to run the wipers 2-3 cycles.
Use this function when the windshield is dirty.
The spray and wiper operation will continue until you release the lever.

WARNING
Do not use the washer in freezing temperatures without 1st warming the windshield with the defrosters; the washer solution could freeze on contact with the

switch is located at the end of the wiper and washer switch lever. Turn the switch to desired position to operate the rear wiper and washer.
- Spraying washer fluid and wiping
INT - Intermittent wiper operation

windshield and obscure your ON - Normal wiper opertion

vision.

- Spraying washer fluid and wip-

ing

4 44

Driving your vehicle

DEFROSTER

CAUTION

To activate the rear window defroster, press the rear window

· To prevent damage to the con- defroster button located in the center

ductors bonded to the inside surface of the rear window,

console switch panel. The indicator in the instrument cluster illuminates

never use sharp instruments when the defroster is ON.

or window cleaners contain- If your vehicle is equipped with the 2

ing abrasives to clean the win- outside mirror defroster, it will be

dow. · To prevent the battery from

operating at the same time when you operate the rear window defroster.

OLD026116N
The defroster heats the window to

being discharged, operate the defroster only while the

If there is heavy accumulation of snow on the rear window, brush it off

engine is running.

before operating the rear defroster.

remove frost, fog and thin ice from the interior and exterior of the rear

· If you want to defrost and defog on the front windshield,

The rear window defroster automatically turns off after 20 minutes or

window, while engine is running.

refer to "Windshield Defrosting when the ignition switch is turned off.

and Defogging" in this section. To turn off the defroster, press the 6

rear window defroster button again.

4 45

Driving your vehicle HAZARD WARNING FLASHER

OLD026100

The hazard warning flasher causes

the rear tail lights and front turn signal lights to flash on and off, which

serves as a warning to other drivers

6 to exercise caution when approach-

ing or passing your vehicle.

To activate the flasher, depress the hazard warning flasher switch. This

switch operates in any ignition switch

8 position.

To turn the flashers off, depress the

9 switch again.

4 46

MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)

Driving your vehicle

1
4 1. Fan speed control knob 2. Mode selection knob 3. Temperature control knob

4. Rear window defroster button 5. Air intake control button

6. Air conditioning button (if equipped)

OLD026120N

4 47

Driving your vehicle

OLD026126N

OLD026124

OLD026202N

Fan speed control knob

Temperature control knob

Mode selection knob

5 The ignition switch must be in the ON The temperature control knob allows The mode selection knob controls

position for fan operation.

you to control the temperature of the the direction of the air flow through

The fan speed control knob allows air flowing from the ventilation sys- the ventilation system. you to control the fan speed of the air tem. To change the air temperature in

flowing from the ventilation system. the passenger compartment turn the

To change the fan speed, turn the knob to the right for warm and hot air knob to the right for higher speed or or left for cooler air.

8 left for lower speed.

4 48

Driving your vehicle

MAX/ A/C position

MAX A/C

When you select the MAX A/C mode while the fan speed is on, the follwing

system settings will be

made automatically; · the air conditioning sys-

tem will be turned on.

· the recirculated air posi- 3

tion will be selected.

· the face mode will be 4
selected.

OLD026121

If you select MAX A/C mode, you will not be able

to cancel the A/C system

operation, or change the recirculated air mode posi-

tion.

Set the fan speed control 7

knob to desired speed and

rotate the temperature control knob to the

extreme left position for

maximum cooling.

(outlet port: B, D)

4 49

Driving your vehicle

Face position

Floor position

Air flow is directed toward

Most of the air flow is

the upper body and face.

directed to the floor, with a

Additionally, each outlet

small amount of the air

can be controlled to direct

being directed to the wind-

the air discharged from the outlet.

shield and side window defroster.

(outlet port: B, D)

(outlet port: C, E, A, D)

3 Face - floor position

Floor - defrost position

Air flow is directed towards

Most of the air flow is

the face and the floor. The air to the floor is warmer

directed to the floor and the windshield with a small

OLD026122

than the air to the face

amount directed to the Instrument panel vents

(except when the temper-

side window defrosters.

If air flow control is not satisfactory,

ature control is set to the

(outlet port: A, C, E, D)

check the instrument panel vents.

extreme cold position). (outlet port: B, D, C, E)

Defrost position

The outlet port (B, D) can be opened

Most of the air flow is or closed separately using the verti-

directed to the windshield cal thumbwheel. To close the vent,

with a small amount of air rotate it upward to the maximum directed to the side win- position. To open the vent, rotate it

dow defrosters. (outlet port: A, D)

downward. Also, you can adjust the direction of

air delivery from these vents using

vertical or horizontal thumbwheels as shown.

4 50

Driving your vehicle

Recirculated air position

Outside (fresh) air position

The indicator light on the button is illuminated when the recirculated air position is selected.

The indicator light on the button is not illuminated
when the outside (fresh) 1
air position is selected.

OLD026125N
Air intake control button

With the recirculated air position selected, air from passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

With the outside (fresh) air position selected, air

enters the vehicle from

outside and is heated or 3

cooled according to the

function selected.

This is used to select outside (fresh)

air position or recirculated air posi-

tion. To change the air intake control posi-

tion, push the control button.

4 51

Driving your vehicle

NOTICE

Prolonged use of the air conditioning with the "recirculated air position" selected, will result in exces-

WARNING - Reciruclated
air
· Continued climate control

sively dry air in the passenger com-

system operation in the recir-

2 partment.

culated air position may allow humidity to increase inside

vehicle which may fog the

glass and obscure visibility.

· Continued climate control

system operation in the reciruclated air position can

OLD026127

slightly reduce oxygen levels Air conditioning button

5 6 7

which can lead to cause drowsiness or sleepiness, and loss of vehicle control. Set the air intake control to the outside (fresh) air position as much as possible while driving.

(if equipped)
Push the A/C button to turn the air conditioning system on (indicator light will illuminate). Push the button again to turn the air conditioning system off.

4 52

Driving your vehicle

System Operation

Heating

Air conditioning (if equipped)

Ventilation

1. Set the mode to the position. All Kia Air Conditioning Systems are

1. Set the mode to the position.
2. Set the air intake control to the outside (fresh) air position.
3. Set the temperature control to the desired position.
4. Set the fan speed control to the desired speed.

2. Set the air intake control to the outside (fresh) air position.
3. Set the temperature control to the desired position.
4. Set the fan speed control to the desired speed.
5. If dehumidified heating is desired, turn the air conditioning system (if

filled with environmentally friendly R-134a refrigerant which is not damaging to the ozone layer.
1. Start the engine. Push the air conditioning button.
2. Set the mode to the position.
3. Set the air intake control to the outside air or recirculated air posi-

1 2 3

equipped) on.

tion.

· If cool air is desired at face level for 4. Set the temperature control knob

bi-level operation, set the mode to

to the desired position.

the position.

5. Set the fan speed control to the

· If the windshield fogs up, set the

desired speed.

mode to the ,

position.

6. Adjust the fan speed control and

temperature control to maintain

maximum comfort. · If warmer air is desired at floor

level for bi-level operation, set the

mode to the

position and 8

adjust the temperature control to

maintain maximum comfort.

4 53

Driving your vehicle

· When maximum cooling is desired, Air conditioning system oper- · The air conditioning system

set the temperature control to the ation tips

includes a function that automati-

1 2

extreme left position and set the air intake control to the recirculated air position, then set the fan speed control to the highest speed.

· If the vehicle has been parked in direct sunlight during hot weather, open the windows for a short time to let the hot air inside the vehicle escape.

NOTICE

· To help reduce moisture inside of

· When using the air conditioning windows on rainy humid days,

cally turns the air conditioning compressor off if engine coolant temperature approaches an over heating level. The air conditioning compressor operation will resume once engine coolant temperature returns to the normal range. Also, the air conditioning compressor is

system, monitor the temperature decrease the humidity inside the automatically turned off for a few

gauge closely while driving up hills or in heavy traffic when out-

vehicle by operating the air conditioning system.

seconds when the accelerator is fully depressed (wide open throt-

side temperatures are high. Air · During air conditioning system tle).

5 6 7 8

conditioning system operation may cause engine overheating. Continue to use the blower fan but turn the air conditioning system off if the temperature gauge indicates engine overheating. · With opening the windows in humid weather air conditioning may cause to make water drops. Be careful because excessive water drop may cause to damage electri-

operation, you may occasionally notice a slight change in engine speed at idle as the air conditioning compressor cycles on. This is a normal system operation characteristics.
· Use the air conditioning system every month if only for a few minutes to ensure maximum system performance.

· When operating the air conditioning system use the outside (fresh) air position.
· Operating the air conditioning system in the recirculated air position does provide maximum cooling, however, continual operation in this mode may cause the air inside the vehicle to become stale.

cal equipment. In this case, close · When using the air conditioning

the windows and turn on the air system, you may notice clear water

conditioning system.

dripping (or even puddling) on the

ground under the passenger side

of the vehicle. This is a normal sys-

tem operation characteristics.

4 54

Checking the amount of air conditioner refrigerant and compressor lubricant
When the amount of refrigerant is low, the performance of the air conditioning is reduced. Overfilling also has a bad influence on the air conditioning system.
Therefore, if abnormal operation is found, have the system inspected by an authorized Kia dealer.

Air conditioner refrigerant and compressor lubricant
WARNING - AC service
The air conditioning system should be serviced by an authorized Kia dealer. Improper service may cause serious injury to the person performing the service.

CAUTION
When the performance of the air conditioning system is reduced it is important that the correct type and amount of oil and refrigerant is used. Otherwise, damage to the compressor and abnormal system operation may occur.

Driving your vehicle
1 2 3 4 5 6 7 8 9
4 55

Driving your vehicle

WINDSHIELD DEFROSTING AND DEFOGGING

CAUTION - Windshield
heating

Do not use or position

during cooling operation in

extremely humid weather. The

difference between the tempera-

ture of the outside air and that

of the windshield could cause the outer surface of the wind-

shield to fog up, causing loss of

OLD026139N

OLD026140N

To defog inside windshield

To defrost outside windshield

visibility. In this case, set the mode selection knob to the position and fan speed control

5 1. Select any fan speed.

1. Set the fan speed to the highest knob to the lower speed.

2. Select desired temperature.

(extreme right) position.

3. Select the or position.

2. Set the temperature to the

4. The outside (fresh) air and air con-

extreme hot position.

ditioning will be selected.

3. Select the position.

If the air-conditioning and outside 4. The outside (fresh) air and air con-

(fresh) air position are not selected

ditioning will be selected.

8 automatically, press the correspon- If the air-conditioning and outside

ding button manually.

(fresh) air position are not selected

automatically, press the corresponding button manually.

4 56

Driving your vehicle

· For maximum defrosting, set the temperature control to the extreme right/hot position and the fan speed control to the highest speed.
· If warm air to the floor is desired while defrosting or defogging, set the mode to the floor- defrost position.
· Before driving, clear all snow and ice from the windshield, rear window, outside rear view mirrors, and all side windows.
· Clear all snow and ice from the hood and air inlet in the cowl grill to improve heater and defroster efficiency and to reduce the probability of fogging up inside of the windshield.

Defogging logic
To reduce the probability of fogging up the inside of the windshield, the air intake is controlled automatically according to certain conditions such as or position. To cancel or return the defogging logic, do the following.

OLD026143N

Manual climate control system

1. Turn the ignition switch to the ON 5
position.

2. Turn the mode selection knob to the defrost position ( ).

3. Push the air intake control button
( ) at least 5 times within 3 sec- 7
onds.

The indicator light in the air intake control button will blink 3 times with

0.5 second of interval. It indicates

that the defogging logic is canceled 9
or returned to the programmed sta-

tus.

If the battery has been discharged or disconnected, it resets to the defog logic status.

4 57

Driving your vehicle

THEFT-ALARM SYSTEM (IF EQUIPPED)

Alarm stage

Withheld alarm

The alarm will be activated when:

When the alarm is armed, the alarm

· Any door is opened without using will not sound if the trunk lid is

the key or the transmitter.

opened with either the key or the

· The trunk lid is opened without transmitter.

using the key or the transmitter.

However, if the trunk lid is not

· The engine hood is opened.

opened completely within 30 seconds after unlocking with the trans-

mitter, the alarm will sound. Also, if

The alarm will sound and the hazard any of the doors or hood is opened

4
Armed stage

HMR.082

warning lights will blink for 27 seconds, then OFF for 10 seconds. This ON/OFF cycle will be repeated three

while the trunk lid is open and the alarm armed, the alarm will sound.

5 The Theft-Alarm system is armed times. During this time, the engine

as follows.

will not start.

6 · After all doors, engine hood, and
trunk are locked, press the "LOCK"

button on the transmitter once.

The hazard flasher lights will flash

once. (At this time, the alarm does

not sound.)

4 58

Disarmed stage
The armed stage will be deactivated when:
· The " " button on the transmitter is pressed (hazard lamps will flash twice).
But, after depressing unlock button, unless you open the doors within 30 seconds all doors will be locked and into armed stage automatically.
· The ignition switch is in the "ON" position.
· Unlock the doors with the ignition key.

The alarm will be deactivated when:

· The lock ( ), unlock ( ) or trunk

lid open (

) button on the

transmitter is pressed.

· The ignition switch is in the "ON" position for 30 seconds or more.

· Unlock the doors with the ignition key.

NOTICE
If the ignition key is in the ignition switch, the transmitter will not function. Avoid trying to start the engine with the alarm activated.

Driving your vehicle
1 2 3 4 5 6 7 8 9
4 59

Fuel requirements / 5-2 Emission control system / 5-3

Before driving / 5-5

Suggestions for economical operation / 5-6

Special driving conditions / 5-7

Vehicle load limit / 5-11 Weight of the vehicle / 5-16

Trailer towing / 5-17

Label information / 5-25

Driving tips

FUEL REQUIREMENTS

Gasoline engine (unleaded)

Gasoline containing alcohol

Vehicle damage or driveability prob-

Your new Kia vehicle is designed to use only unleaded fuel with a minimum Octane Rating of 87 Anti-

and methanol
Gasohol, a mixture of gasoline and ethanol (also known as grain alco-

lems may not be covered by the manufacturer's warranty if they result from the use of:

Knock Index (AKI).

hol), and gasoline or gasohol con- 1. Gasohol containing more than

2 3 4 5 6

NOTICE
NEVER USE LEADED FUEL. The use of leaded fuel is detrimental to the catalytic converter and will damage the engine control system's oxygen sensor and affect emission control. Never add any fuel system cleaning agents to the fuel tank other than what Kia has specified. (Consult an Authorized Kia Dealer for details.)

taining methanol (also known as wood alcohol) are being marketed along with or instead of leaded or unleaded gasoline.
Do not use gasohol containing more than 10% ethanol, and do not use gasoline or gasohol containing any methanol. Either of these fuels may cause drivability problems and damage to the fuel system.
Discontinue using gasohol of any kind if drivability problems occur.

10% ethanol. 2. Gasoline or gasohol containing
methanol. 3. Leaded fuel or leaded gasohol.
CAUTION
Never use gasohol which contains methanol. Discontinue use of any gasohol product which impairs drivability.

Driving tips

EMISSION CONTROL SYSTEM

The emission control system of your Engine exhaust gas precau-

· Do not operate the engine in con-

vehicle is covered by a written limited tions (carbon monoxide)

fined or closed areas (such as

warranty. Please see the warranty

garages) any more than what is

information contained in the

WARNING

necessary to move the vehicle in or 1

Warranty & Consumer Information Manual in your vehicle.

Engine exhaust gases contain carbon monoxide (CO). Though colorless and odorless, it is

out of the area.
· When the vehicle is stopped in an open area for more than a short

Vehicle modifications

dangerous and could be lethal if

time with the engine running,

This vehicle should not be modified. Modification of your Kia could affect its performance, safety or durability, may violate governmental safety and

inhaled. Follow the instructions following to avoid CO impairment.

adjust the ventilation system (as needed) to draw outside air into the vehicle.
· Never sit in a parked or stopped

3 4

emissions regulations.

· Carbon monoxide can be present vehicle for any extended time with

In addition, damage or performance problems resulting from any modification may not be covered under warranty.

with other exhaust fumes. the engine running. Therefore, if you smell exhaust · When the engine stalls or fails to

fumes of any kind inside your vehicle, have it inspected and repaired

start, excessive attempts to restart the engine may cause dam-

immediately by an authorized Kia age to the emission control sys-

dealer. If you ever suspect exhaust tem. fumes are coming into your vehi-

cle, drive it only with all the win-

dows fully open. Have your vehicle checked and repaired immediately.

Driving tips

Operating precautions for cat- · Do not operate the engine at high

alytic converters

idle speed for extended periods (5

minutes or more).

WARNING - Fire

· Do not modify or tamper with any

A hot exhaust system can ignite

flammable items under your vehicle. Do not park the vehicle

over or near flammable objects,

part of the engine or emission control system. All inspections and adjustments must be made by an authorized Kia dealer.

3 such as dry grass, paper, Failure to observe these precautions

leaves, etc.

could result in damage to the catalyt-

ic converter and to your vehicle. Your vehicle is equipped with a cat- Additionally, such actions could void

alytic converter emission control your warranties.

5 device.
Therefore, the following precautions

must be observed:
6 · Use only UNLEADED FUEL for

gasoline engine (unleaded).

7 · Do not operate the vehicle when

there are signs of engine malfunc-

tion, such as misfire or a noticeable loss of performance.

· Do not misuse or abuse the

engine. Examples of misuse are

coasting with the ignition off and

descending steep grades in gear

with the ignition off.

Driving tips

BEFORE DRIVING

Before entering vehicle:

Before starting

· Be sure that all windows, outside mirror(s), and outside lights are clean.
· Check the condition of the tires.
· Check under the vehicle for any

· Close and lock all doors.
· Position the seat so that all controls are easily reached.
· Adjust the inside and outside rearview mirrors.

WARNING - Driving under
the influence of alcohol or drugs
Drinking and driving is dangerous. Drunk driving is the number one contributor to the high-

1 2

sign of leaks.

· Be sure that all lights work.

way death toll each year. Even a

· Be sure there are no obstacles behind you if you intend to back up.
Necessary inspections

· Check all gauges.
· Check the operation of warning lights when the ignition switch is turned to the ON position.

small amount of alcohol will affect your reflexes, perceptions and judgement.
You are much more likely to

3 4

Fluid levels, such as engine oil, engine coolant, brake fluid, and washer fluid should be checked on a regular basis, with the exact interval depending on the fluid. Further details are provided in Section 7, Maintenance.

· Release the parking brake and make sure the brake warning light goes out.
For safe operation, be sure you are familiar with your vehicle and its equipment.

have a serious accident if you drink and drive.
If you are drinking or taking drugs, don't drive. Do not ride with a driver who has been drinking or taking drugs. Choose a designated driver or call a cab.

5 6 7

Driving while under the influ-
ence of drugs is as dangerous 8

or more dangerous than driving

drunk.

Driving tips

SUGGESTIONS FOR ECONOMICAL OPERATION

Your vehicle's fuel economy depends · Do not use the air conditioner · Open windows at high speeds can

mainly on your style of driving, where unnecessarily.

reduce fuel economy.

you drive and when you drive.

· Slow down when driving on rough · Fuel economy is less in crosswinds

1 Each of these factors affects how roads.

and headwinds. To help offset

many kilometers (miles) you can get · For longer tire life and better fuel some of this loss, slow down when

from a liter (gallon) of fuel. To operate your vehicle as economically as pos-

economy, always keep the tires inflated to the recommended pres-

driving in these conditions.

sible, use the following driving suggestions to help save money in both fuel and repairs:

sures.
· Maintain a safe distance from other vehicles to avoid sudden stops.

Keeping a vehicle in good operating condition is important both for economy and safety. Therefore, have an

· Avoid lengthy warm-up idling. Once the engine is running

This will reduce wear on brake lin- authorized Kia dealer perform ings and pads. Driving in such a scheduled inspections and mainte-

smoothly, begin driving.

way will also save fuel because nance.

Remember, engine warm-up may extra fuel is required to accelerate

take a little longer on cold days.

back to driving speed.

WARNING - Engine off

· Save fuel by accelerating slowly · Do not carry unnecessary weight

after stopping.

in the vehicle.

during motion Never turn the engine off to

· Keep the engine in tune and follow · Do not rest your foot on the brake coast down hills or anytime the

the recommended periodic mainte- pedal while driving. This can cause vehicle is in motion. The power

nance schedule. This will increase needless wear, possible damage steering and power brakes will

the life of all parts and lower your operating costs.

to the brakes, and poor fuel econo- not function properly without

my.

the engine running. Instead,

· Improper wheel alignment results downshift to an appropriate

in faster tire wear and lower fuel gear for engine braking effect.

economy.

Driving tips

SPECIAL DRIVING CONDITIONS

Hazardous driving conditions · If stalled in snow, mud, or sand, Rocking the vehicle

When hazardous driving conditions are encountered such as water, snow, ice, mud, sand, or similar haz-

use second gear. Accelerate slowly to avoid spinning the drive wheels.

If it is necessary to rock the vehicle to free it from snow, sand, or mud, first turn the steering wheel right and

ards, follow these suggestions:

· Use sand, rock salt, tire chains, or left to clear the area around your

· Drive cautiously and allow extra distance for braking.
· Avoid sudden movements in braking or steering.
· When braking, pump the brake pedal with a light up-and-down motion until the vehicle is stopped.
WARNING
Do not pump the brake pedal on a vehicle equipped with ABS.

other non-slip material under the drive wheels to provide traction when stalled in ice, snow, or mud.
WARNING - Downshifting
Downshifting with an automatic transaxle, while driving on slippery surfaces can cause an accident. The sudden change in tire speed could cause the tires to skid. Be careful when downshifting on slippery surfaces.

front wheels. Then, shift back and forth between 1 (First) and R (Reverse) in vehicles equipped with a manual transaxle or R (Reverse) and any forward gear in vehicles equipped with an automatic transaxle. Do not race the engine, and spin the wheels as little as possible. If you are still stuck after a few tries, have the vehicle pulled out by a tow vehicle to avoid engine overheating and possible damage to the transaxle.

2 3 4 5 6

CAUTION

Prolonged rocking may cause
engine over-heating, transaxle 8

damage or failure, and tire dam-

age.

Driving tips

CAUTION

Driving at night

Driving in the rain

The TCS system (if equipped) should be turned OFF prior to rocking the vehicle.

Because night driving presents more hazards than driving in the daylight, here are some important tips to remember:

Rain and wet roads can make driving dangerous, especially if you're not prepared for the slick pavement. Here are a few things to consider

· Slow down and keep more dis- when driving in the rain:

WARNING - Spinning tires
3 Do not spin the wheels, espe-

tance between you and other vehi- · A heavy rainfall will make it harder cles, as it may be more difficult to to see and will increase the dissee at night, especially in areas tance needed to stop your vehicle,

cially at speeds more than 56

where there may not be any street so slow down.

4 5

km/h (35 mph). Spinning the wheels at high speeds when the vehicle is stationary could cause a tire to overheat, explode and injure bystanders.

lights.
· Adjust your mirrors to reduce the glare from other driver's headlights.
· Keep your headlights clean and

· Keep your windshield wiping equipment in good shape. Replace your windshield wiper blades when they show signs of streaking or missing areas on the windshield.

properly aimed on vehicles not · If your tires are not in good condiequipped with the automatic head- tion, making a quick stop on wet

light aiming feature. Dirty or pavement can cause a skid and

improperly aimed headlights will possibly lead to an accident. Be

make it much more difficult to see sure your tires are in good shape.

at night.

· Turn on your headlights to make it

· Avoid staring directly at the head- easier for others to see you.

lights of oncoming vehicles. You

could be temporarily blinded, and it will take several seconds for your

eyes to readjust to the darkness.

Driving tips

· Driving too fast through large pud- Winter driving

· Use antifreeze-formulated wind-

dles can affect your brakes. If you must go through puddles, try to drive through them slowly.

· We recommend that you carry emergency equipment, including a window scraper, windshield de-

shield washer fluid. (Do not use engine coolant antifreeze.)
· Do not use the parking brake if it

· If you believe you may have gotten icer, a bag of sand or salt, flares, a might freeze. When parking, shift

your brakes wet, apply them lightly while driving until normal braking operation returns.

small shovel and jumper cables.
· Make sure you have sufficient ethylene-glycol coolant in the radiator.
· Check the battery condition and

to 1 (First) or R (Reverse) with a manual transaxle or P (Park) with

an automatic transaxle and block

the rear wheels.

cables. Cold temperatures reduce

the capacity of any battery, so it must be in excellent condition to

provide enough winter starting

power.

· Make sure the engine oil viscosity

is suitable for cold weather.

· Check the ignition system for loose

connections and damage.

Driving tips

Snow tires

Driving in flooded areas

If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as the

WARNING - Snow tire
size
Snow tires should be equivalent

Avoid driving through flooded areas unless you are sure the water is no higher than the bottom of the wheel

original tires. Mount snow tires on all in size and type to the vehicle's hub. Drive through any water slowly.

four wheels to balance your vehicle's handling in all weather conditions.

standard tires. Otherwise, the safety and handling of your

Allow adequate stopping distance because brake performance may be

Keep in mind that the traction provid- vehicle may be adversely affect- affected.

3 4

ed by snow tires on dry roads may not be as high as your vehicle's original equipment tires. You should drive cautiously even when the roads are clear. Check with the tire dealer for

ed.
Do not install studded tires without first checking local and provincipal

After driving through water, dry the brakes by gently applying them several times while the vehicle is moving slowly.

maximum speed recommendations.

regulations for possible restrictions against their use.

5 10

Driving tips

VEHICLE LOAD LIMIT

Type A

Vehicle capacity weight:

Towing capacity:

385 kg (849 lbs)

Without trailer brakes:

Vehicle capacity weight is the maxi- 340 kg (750 lbs) mum combined weight of occupants With trailer brakes:

and cargo. If your vehicle is equipped 680 kg (1500 lbs)

with a trailer, the combined weight Towing capacity is the maximum 2

includes the tongue load.

trailer weight including its cargo

Type B

OLD056900N

Seating capacity:
Total : 5 persons (Front seat : 2 persons, Rear seat : 3 persons)

weight, your vehicle can tow.

Cargo capacity:
The cargo capacity of your vehicle 4
will increase or decrease depending

Seating capacity is the maximum on the weight and the number of number of occupants including a occupants and the tongue load, if

driver, your vehicle may carry. your vehicle is equipped with a trail-

However, the seating capacity may er.

be reduced based upon the weight of

OLD056901N all of the occupants, and the weight

Tire and loading information

of the cargo being carried or towed.

label

Do not overload the vehicle as there

The label located on the driver's door is a limit to the total weight, or load sill gives the original tire size, cold limit including occupants and cargo,

tire pressures recommended for your the vehicle can carry.

vehicle, the number of people that

can be in your vehicle and vehicle

capacity weight.

5 11

Driving tips

Steps for determining correct load limit

5. Determine the combined weight of luggage and cargo being loaded

WARNING - Load distribu-

1 2

1. Locate the statement "The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.'' on your vehicle's placard.

on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
6. If your vehicle will be towing a trail-

tor
Your vehicle may become unstable while towing if your vehicle is overloaded to one side. Make sure that the load in the vehicle is

2. Determine the combined weight of the driver and passengers that will

be riding in your vehicle.

er, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and

distributed equally to each side of the centerline.

4 3. Subtract the combined weight of
the driver and passengers from

luggage load capacity of your vehicle.

XXX kg or XXX lbs.
5 4. The resulting figure equals the

available amount of cargo and lug-

gage load capacity. For example, if the "XXX" amount equals 635 kg

(1400 lbs.), and there will be five

68 kg (150 lbs.) passengers in

your vehicle, the amount of avail-

able cargo and luggage load capacity is 295 kg (650 lbs.).

(635-340 (5 x 68) = 295 kg or

1400-750 (5 x 150) = 650 lbs.)

5 12

Driving tips

Example 1

Example 2

Example 3

C190F01JM

C190F02JM

C190F03JM

Item Description

Total

Vehicle Capacity 635 kg

Item Description

Total

Vehicle Capacity 635 kg

Item Description

Total

Vehicle Capacity 635 kg

Weight

(1400 lbs)

Weight

(1400 lbs)

Weight

(1400 lbs)

Subtract Occupant 136 kg

Subtract Occupant 340 kg

Subtract Occupant 390 kg

Weight

(300 lbs)

68 kg (150 lbs) × 2

Weight

(750 lbs)

68 kg (150 lbs) × 5

Weight

(860 lbs)

78 kg (172 lbs) × 5

Available Cargo and 499 kg C Luggage weight (1100 lbs)

Available Cargo and 295 kg C Luggage weight (650 lbs)

Available Cargo and 245 kg

C Luggage weight (540 lbs)

5 13

Driving tips

Refer to your vehicle's tire and loading information label for specific information about your vehicle's
1 capacity weight and seating posi-
tions. The combined weight of the driver, passengers and cargo should
2 never exceed your vehicle's capacity
weight.
3
4

OLD056901C

This label also tells you the maximum weight that can be supported by the front and rear axles, called Gross Axle Weight Rating (GAWR).
To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle.Your dealer can help you with this. Be sure to spread out your load equally on both sides of the centerline.

Vehicle certification

The vehicle certification label is

located on the driver's door sill.

This label shows the maximum allowable weight of the fully loaded

vehicle. This is called the GVWR

(Gross Vehicle Weight Rating). The

GVWR includes the weight of the

vehicle, all occupants, fuel and cargo.

5 14

Driving tips

WARNING - Over loading

CAUTION

WARNING - Loose cargo

· Never exceed the GVWR for · Overloading your vehicle may Items you carry inside your

your vehicle, the GAWR for

cause damage. Repairs would

vehicle can strike and injure

either the front or rear axle

not be covered by your war- occupants in a sudden stop or

and vehicle capacity weight. Exceeding these ratings can

ranty. Do not overload your vehicle.

sharp turn, or in a crash. · Put items in the trunk of your

cause an accident or vehicle · Using heavier suspension

vehicle. Try to spread the

damage. You can calculate the weight of your load by weighing the items (or people) before putting them in the vehicle. Be careful not to over-

components to get added durability might not change your weight ratings. Ask your dealer to help you load your vehicle the right way.ignored.

weight evenly.
· Never stack items, like suitcases, inside the occupant compartment.

3 4

load your vehicle.
· If you overload your vehicle, the tires can suddenly and without warning fail. The overloading can also make your

The label will help you decide how much cargo and installed equipment your vehicle can carry.

· Do not leave an unsecured child restraint in your vehicle, since it can injure occupants in a crash.
· When you carry something

5 6

vehicle unstable and dramati-

inside the vehicle, secure it.

cally increase braking dis- If you carry items inside your vehicle

tance. This could cause you to - like suitcases, tools, packages, or

lose control and crash.

anything else - they are moving as fast as the vehicle. If you have to stop

or turn quickly, or if there is a crash,

the items will keep going and can cause an injury if they strike the driv-

er or a passenger.

5 15

Driving tips

WEIGHT OF THE VEHICLE

This section will guide you in the GAW (Gross axle weight)

GCWR (Gross combined weight

proper loading of your vehicle and/or This is the total weight placed on rating)

trailer, to keep your loaded vehicle each axle (front and rear) - including This is the maximum allowable

1 weight within its design rating capa- vehicle curb weight and all payload. weight of the vehicle and the loaded

2 3 4

bility, with or without a trailer. Properly loading your vehicle will provide maximum return of the vehicle design performance. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle's weight ratings, with or without a trailer, from the vehicle's specifications and the compliance

GAWR (Gross axle weight rating)
This is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the vehicle certification label. The total load on each axle must never exceed its GAWR.

trailer - including all cargo and passengers - that the vehicle can handle without risking damage. (Important : The towing vehicle's braking system is rated for operation at GVWR, not GCWR. Separate functional brakes should be used for safe control of towed vehicles and for trailers weighing an 340kg (750 lbs).) The GCW

label:
5 Base curb weight

GVW (Gross vehicle weight)

must never exceed the GCWR.

This is the Base Curb Weight plus Maximum trailer weight

This is the weight of the vehicle including a full tank of fuel and all

actual Cargo Weight plus passengers.

This is the highest possible weight of a fully loaded trailer the vehicle can

standard equipment. It does not GVWR (Gross vehicle weight rating) tow. It assumes a vehicle with only

include passengers, cargo, or option- This is the maximum allowable mandatory options, no cargo, and a

al equipment.

weight of the fully loaded vehicle driver. The weight of other optional

Vehicle curb weight

(including all options, equipment, equipment, passengers and cargo in

This is the weight of your new vehicle passengers and cargo). The GVWR your vehicle will reduce the maxiwhen you picked it up from your deal- is shown on the vehicle certification mum trailer weight your vehicle can

er plus any aftermarket equipment. Cargo weight

label located on the driver's door sill. tow. GCW (Gross combined weight)

This figure includes all weight added This is the weight of the loaded vehi-

to the Base Curb Weight, including cle (GVW) plus the weight of the fully

cargo and optional equipment.

loaded trailer.

5 16

Driving tips

TRAILER TOWING

Calculating the load your vehicle can tow

WARNING - Towing a

CAUTION

1. Use the appropriate maximum

trailer

Pulling a trailer improperly can

GCWR chart (in the Weight of the If you don't use the correct

damage your vehicle and result

Trailer section in this chapter) for equipment or you drive improp- in costly repairs not covered by

your type of drive system and erly, you can lose control when

transmission.

you pull a trailer. For example, if

your warranty.

2. Weigh your vehicle.

the trailer is too heavy, the To identify what the vehicle trailering

3. Subtract the weight of your vehicle from the maximum GCWR in the chart. This is the maximum trailer weight your vehicle can tow. It must be below the maximum trailer weight shown in the chart. Note that the maximum trailer weight your vehicle can tow depends on the total weight of any cargo, passengers and available equipment

brakes may fail, and would at least be ineffective to promptly stop the vehicle. You and your passenger could be seriously or fatally injured. We do not recommend towing a trailer. However, in the event there is a need to tow a trailer, such as in an emergency, follow all the steps in this section.

capacity is for your vehicle, you should read the information in "Weight of the Trailer" that appears later in this section. Remember that trailering is different than just driving your vehicle by itself. Trailering causes major changes in handling, durability, and fuel economy. Successful, safe trailering requires correct equipment, and cautious driving.

3 4 5 6

in the vehicle.

Item

Specification

Maximum trailer

Without trailer brakes

340 (750)

weight

kg (lbs.) With trailer brakes

680 (1500)
9

5 17

Driving tips

This section contains many time- If you do decide to pull a trailer Weight of the trailer

1 2 3 4

tested, important trailering tips and safety rules. Many of these are important for your safety and that of your passengers. Please read this section carefully before you pull a trailer.
Load-pulling components such as the engine, transaxle, wheel assemblies, and tires are forced to work harder against the load of the added weight. The engine is required to operate at relatively higher speeds

Here are some important points if you decide to pull a trailer:
· Consider using a sway control. You can ask a hitch dealer about sway control.
· After your odometer indicates 800 km (500 miles) or more, you can tow a trailer. For the first 800 km (500 miles) that you tow a trailer, don't drive over 80 km/h (50 mph) and don't make starts at full throt-

How heavy can a trailer safely be? It should never weigh more than the maximum trailer weight with trailer brakes. But even that can be too heavy.
If you feel that the trailer is adversely affecting the movement of your vehicle, reduce your speed, avoid uneven or winding roads, avoid roads with steep grades, and/or lighten your trailer load.

and under greater loads. This additional burden generates extra heat

tle. This helps your engine and other parts of your vehicle "wear" in

which creates more wear in engine, at the heavier loads.

and a shortened engine life. The trail- · Always drive your vehicle at a moder also adds considerably to wind erate speed (less than 100 km/h

resistance, increasing the pulling (60 mph)).

7 requirements.

· The important considerations have

to do with weight:

5 18

Driving tips

Weight of the trailer tongue

Hitches

The tongue load of any trailer is an

WARNING - Trailer bal-

It's important to have the correct

important weight to measure

ance

hitch equipment. Crosswinds, large

because it affects the total gross · Never load a trailer with more trucks going by, and rough roads are 1

vehicle weight (GVW) of your vehicle

weight in the rear than in the a few reasons why you'll need the

since that is the trailer weight pushing down on the hitch on your vehi-

front. The front should be loaded with approximately

right hitch. Here are some rules to follow:

cle. The rest of the trailer weight is

60% of the total trailer load; · Do not attach a trailer hitch which

sitting on the trailer's wheels. The trailer tongue should weigh a

the rear should be loaded with approximately 40% of the total

requires you to alter other parts on 3
your vehicle.

maximum of 10% of the total loaded trailer weight.

trailer load. · Never exceed the maximum

· Never make a hole in your vehicle to accommodate a hitch.

After you've loaded the trailer, go to a Weigh Station and weigh the trailer and then the tongue, separately, to see if the weights are proper. If they aren't, you may be able to correct them simply by moving some items around in the trailer.

weight limits of the trailer or trailer towing equipment. Improper loading can result in damage to your vehicle and/or personal injury. Check weights and loading at a commercial scale or highway patrol office

· The bumpers on your vehicle are not intended for hitches. Do not attach rental hitches or other bumper-type hitches to them. Use only a frame-mounted hitch that does not attach to the bumper.

5 6

equipped with scales.

· An improperly loaded trailer

can cause loss of vehicle control.

5 19

Driving tips

Safety chains

Trailer brakes

Driving with a trailer

You should always attach chains If your trailer weighs more than the Towing a trailer requires experience.

between your vehicle and your trail- maximum weight for a trailer without You must gain that experience slow-
1 er. Cross the safety chains under the brakes, then the trailer needs its own ly and carefully which practicing with

tongue of the trailer so that the brakes. You must consult with a an unloaded or lightly loaded trailer.

tongue will not drop to the road if it knowledgeable and reputable trailer Before setting out for the open road, becomes separated from the hitch. vendor to determine which brake you must get to know your trailer.

Instructions about safety chains may equipped trailer is right for your Acquaint yourself with the feel of

be provided by the hitch manufactur- needs. Be sure to read and follow the handling and braking with the trailer. er or by the trailer manufacturer. instructions for the trailer brakes so And always keep in mind that the

Follow the manufacturer's recom- you'll be able to install, adjust and vehicle you are driving is now a good

mendation for attaching safety maintain them properly.

deal longer and not nearly so

chains. Always leave just enough

responsive as your vehicle is by

5 6 7 8

slack so you can turn with your trailer. And, never allow safety chains to drag on the ground.

WARNING
Do not use a trailer with its own brakes unless you are absolutely certain that you have properly set up the brake system. This is not a task for amateurs. Use an experienced, competent trailer shop for this work.

itself.
Before you start, check the trailer hitch and platform, safety chains, electrical connector(s), lights, tires and mirror adjustment. If the trailer has electric brakes, start your vehicle and trailer moving and then apply the trailer brake controller by hand to be sure the brakes are working. This lets you check your electrical connection

at the same time.

During your trip, check occasionally

to be sure that the load is secure,

and that the lights and any trailer

brakes are still working.

5 20

Driving tips

Following distance

Backing up

Turn signals when towing a trailer

Stay at least twice as far behind the The trailer will go in the opposite When you tow a trailer, your vehicle

vehicle ahead as you would when direction of the rear of your vehicle has to have a different turn signal
driving your vehicle without a trailer. when backing up. This is very difficult flasher and extra wiring. The green 1

This can help you avoid situations for an inexperienced trailer driver to arrows on your instrument panel will

that require heavy braking and sud- get used to. To help you avoid mis- flash whenever you signal a turn or

den turns.

takes, hold the bottom of the steering lane change. Properly connected,

wheel with one hand. Then, to move the trailer lights will also flash to alert

Passing

the trailer to the left, just hold the other drivers you're about to turn, steering wheel firmly and move your change lanes, or stop.

You'll need more passing distance up ahead when you're towing a trailer. And, because you're a good deal longer, you'll need to go much farther beyond the passed vehicle before you can return to your lane.

hand to the left. To move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you.
Making turns When you're turning with a trailer, make wider turns than normal. Do this so your trailer won't strike soft shoulders, curbs, road signs, trees, or other objects. Avoid jerky or sud-

When towing a trailer, the green arrows on your instrument panel will flash for turns even if the bulbs on the trailer are burned out. Thus, you may think drivers behind you are seeing your signals when, in fact, they are not. It's important to check reqularly to be sure the trailer bulbs are still working. You must also check the lights every time you disconnect and then reconnect the wires.

4 5 6 7

den maneuvers. Signal well in

advance.

5 21

Driving tips

Do not connect a trailer lighting sys- Driving on grades tem directly to your vehicle's lighting Reduce speed and shift to a lower

CAUTION

system. Use only an approved trailer gear before you start down a long or When towing a trailer on steep

1 wiring harness.

steep downgrade. If you don't shift grades especially (in excess of

Your Authorized Kia Dealer can down, you might have to use your 6%) pay close attention to the

assist you in installing the wiring har- brakes so much that they would get

ness.

hot and no longer operate efficiently.

engine coolant temperature gauge to ensure the engine

3 4 5 6

WARNING - Trailer wiring
harness
Failure to use an approved trailer wiring harness could result in damage to the vehicle's electrical system, there by disabling the brake light system resulting in an accident.

On a long uphill grade, shift down and reduce your speed to around 70 km/h (45 mph) to reduce the possibility of engine and transaxle overheating.
Operating your vehicle in D (Drive) when towing a trailer will minimize heat buildup and extend the life of your transaxle.

does not overheat. If the needle of the coolant temperature gauge moves across the dial towards "H" (HOT), pull over and stop as soon as it is safe to do so, and allow the engine to idle until it cools down.You may proceed once the engine has cooled sufficiently.

5 22

Driving tips

Parking on hills

However, if you ever have to park When you are ready to leave after

Generally, you should not park your your trailer on a hill, here's how to do parking on a hill

vehicle, with a trailer attached, on a it:

1. With the manual transaxle in

hill. People can be seriously or fatal- 1. Apply your brakes, but don't shift

Neutral or automatic transaxle in P 1

ly injured, and both your vehicle and into gear.

(Park), apply your brakes and hold

the trailer can be damaged if they 2. Have someone place chocks

begin to move downhill.

(blocks of wood or metal intended

the brake pedal down while you: · Start your engine;

WARNING - Parking on a

for this purpose) under the downhill sides of the trailer wheels.

· Shift into gear; and · Release the parking brake.

hill
Parking your vehicle on a hill with a trailer attached is dangerous. It could cause serious injury or death, should the trail-

3. When the wheel chocks are in place, release the brakes until the chocks absorb the load.
4. Reapply the brakes. Apply your parking brake, and then shift to R

2. Slowly remove your foot from the brake pedal.
3. Drive slowly forward until the trailer is clear of the chocks.

4 5

er break lose, or should the trail-

(Reverse) for a manual transaxle 4. Stop and have someone pick up

er drag the vehicle downhill.

or P (Park) for an automatic transaxle.

and store the chocks.

5. Release the brakes.
7

WARNING - Parking brake

It can be dangerous to get out of

your vehicle if the parking brake

is not firmly set or if the engine is still running. In either case

the vehicle can move suddenly.

You or others could be serious-

ly or fatally injured.

5 23

Driving tips

Maintenance when trailer towing

CAUTION

1 2 3

Your vehicle will need service more often when you regularly pull a trailer. Important items to pay particular attention to include engine oil, automatic transaxle fluid, axle lubricant and cooling system fluid. Brake condition is another important item to frequently check. Each item is cov-

· Due to higher load during trailer usage, overheating might occur in hot days or during uphill driving. If the coolant gauge indicates overheating, switch off the A/C and stop the vehicle in a safe area to cool down the engine.

ered in this manual, and the Index will help you find them quickly. If

· When towing check transaxle fluid more frequently.

you're trailering, it's a good idea to · If your vehicle is not equipped

review these sections before you start your trip.

with the air conditioner, you should install a condenser fan

Don't forget to also maintain your
6 trailer and hitch. Follow the mainte-

for engine performance when towing a trailer.

nance schedule that accompanied

your trailer and check it periodically. Preferably, conduct the check at the

start of each day's driving. Most

importantly, all hitch nuts and bolts should be tight.

5 24

LABEL INFORMATION
There are several important labels and identification numbers located on your vehicle. The label locations are identified in the illustrations shown.

Frame number

VIN label

Vehicle certification label (MVSS label)

1LDA6001 VIN bar code

1LDN6002
Vehicle identification number (VIN)
To check the frame number under the passenger seat, remove the cover by pulling one side marked with "PULL".

Driving tips
1 2 3
1LD6001
4 5 6 7
1LDN6003
8 9
5 25

Driving tips

1LDN6001

Tire specification / pressure
5 label

Engine number

OLD066005

5 26

Road warning / 6-2 Tires pressure monitoring system (TPMS) / 6-3

Overheating / 6-8

Emergency starting / 6-9

Electrical circuit protection / 6-12

Towing / 6-19 If you have a flat tire / 6-24

In case of an emergency

ROAD WARNING
1 2 3

· The hazard warning flasher operates whether your vehicle is running or not.
· The turn signals do not work when the hazard flasher is on.
· Care must be taken when using the hazard warning flasher while the vehicle is being towed.

OLD026100

Hazard warning flasher

5 The hazard warning flasher serves

as a warning to other drivers to exer-

cise extreme caution when approaching, overtaking, or passing

your vehicle. It should be used when-

ever emergency repairs are being made or when the vehicle is stopped

near the edge of a roadway.

8 Depress the flasher switch with the

ignition switch in any position. The

flasher switch is located in the center console switch panel. All turn signal

lights will flash simultaneously.

In case of an emergency

TIRES PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)

As an added safety feature, your Your vehicle has also been equipped

vehicle has been equipped with a tire with a TPMS malfunction indicator to

pressure monitoring system (TPMS) indicate when the system is not

that illuminates a low tire pressure operating properly. The TPMS mal- 1
telltale when one or more of your function indicator is provided by a

tires is significantly under-inflated. separate telltale, which displays the
Accordingly, when the low tire pres- symbol "TPMS" when illuminated. 2

sure telltale illuminates, you should When the malfunction indicator is

stop and check your tires as soon as illuminated, the system may not be possible, and inflate them to the able to detect or signal low tire pres-

proper pressure. Driving on a signif- sure as intended. TPMS malfunctions

OLD626200N icantly under-inflated tire causes the may occur for a variety of reasons, tire to overheat and can lead to tire including the installation of replace-

(1) TPMS Malfunction Indicator

failure. Under-inflation also reduces ment or alternate tires or wheels on

(2) Low Tire Pressure Telltale

fuel efficiency and tire tread life, and the vehicle that prevent the TPMS 5

may affect the vehicle's handling and from functioning properly. Always

Each tire, including the spare (if pro- stopping ability. vided), should be checked monthly

check the TPMS malfunction telltale after replacing one or more tires or

when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for

Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.

wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.

7 8 9

those tires.)

In case of an emergency

Low tire pressure telltale

CAUTION - Changing tem-
peratures

When the tire pressure monitoring

In winter or cold weather, the low tire pressure telltale may be

system warning telltale is illuminat- illuminated if the tire pressure

2 ed, one or more of your tires is sig- was adjusted to the recom-

nificantly under-inflated. Immediately mended tire inflation pressure

reduce your speed, avoid hard cornering and anticipate increased stop-

in warm weather. It does not mean your TPMS is malfunction-

ping distances. You should stop and ing because the decreased tem-

check your tires as soon as possible. Inflate the tires to the proper pres-

perature leads to a proportional lowering of tire pressure.

5 6 7 8

sure as indicated on the vehicle's placard or tire inflation pressure label located on the driver's side center pillar outer panel. If you cannot reach a service station or if the tire cannot hold the newly added air, replace the low pressure tire with the temporary spare tire. Then the TPMS malfunction indicator may turn on and the Low Tire Pressure telltale may turn off after restarting and about 20 min-

When you drive your vehicle from a warm area to a cold area or from a cold area to a warm area, or the outside temperature is greatly higher or lower, you should check the tire inflation pressure and adjust the tires to the recommended tire inflation pressure.

utes of continuous driving before you

9 have the low-pressure tire repaired

and replaced on the vehicle.

WARNING - Low pressure
damage
Significantly low tire pressure makes the vehicle unstable and can contribute to loss of vehicle control and increased braking distances.
Continued driving on low pressure tires can cause the tires to overheat and fail.

In case of an emergency

TPMS (Tire pressure

NOTICE

(Continued)

monitoring system) malfunction telltale

TPMS

The TPMS malfunction indicator turns on and stays on when there is a problem with the Tire Pressure Monitoring System. If the system is able to correctly detect an under-inflation warning at the same time as system failure then it will illuminate both the TPMS mal-

· The TPMS malfunction indicator may be illuminated if the vehicle is moving around electric power supply cable or radio transmitter such as near police stations, government and public offices, broadcasting stations, military installations, airports, or transmitting tower, etc. which can interfere with normal

· If there is a failed tire sensor, it is possible for the TPMS to temporarily learn a replacement sensor if closely driven to another vehicle that is also equipped with TPMS. In rare cases, this may temporarily delay the TPMS malfunction indicator from turning on.

1 2 3

function and the low tire pressure telltale e. g. if Front Left sensor fails, the

operation of the Tire Pressure Monitoring System (TPMS).

TPMS malfunction indicator turns on, · The TPMS malfunction indicator

but if Front Right, Rear Left, or Rear Right tire is under-inflated, the low tire

may be illuminated if some electronic devices, such as notebook

pressure telltale may turn on at the computers, are used in the vehicle.

same time as the TPMS malfunction indicator.

This can interfere with normal operation of the Tire Pressure

Have the system checked by an authorized Kia dealer as soon as pos-

Monitoring System (TPMS). (Continued)

sible to determine the cause of the

problem.

In case of an emergency

Changing a tire with TPMS

After you replace the low pressure Always be sure the tire is cold before

If you have a flat tire, the Low Tire Pressure telltale will turn on. Have the flat tire repaired by an authorized Kia dealer as soon as possible or

tire with the temporary spare tire, the TPMS malfunction indicator may illuminate after restarting and about 20 minutes of continuous driving.

inflating to the recommended pressure.
A cold tire means the vehicle has been sitting for 3 hours and driven for

replace the flat tire with the tempo- Once the low pressure tire is re-inflat- less than 1.6 km (1 mile) in that 3

rary spare tire.

ed to the recommended pressure hour period.

and installed on the vehicle, the

3 4 5

NOTICE
NEVER use a puncture-repairing agent to repair and/or inflate a low pressure tire. If used, you will have to replace the tire pressure sensor.

TPMS malfunction indicator and the low tire pressure telltale will be soon extinguished. If the low pressure and TPMS malfunction indicators are not extinguished after about 20 minutes of continuous driving, please visit an authorized Kia dealer.

CAUTION
· Do not use any tire sealant if your vehicle is equipped with a Tire Pressure Monitoring System. The liquid sealant can damage the tire pressure sen-

6 7 8 9

Each wheel is equipped with a tire pressure sensor mounted inside the tire behind the valve stem. You must use TPMS specific wheels. It is recommended that you always have your tires serviced by an authorized Kia dealer as soon as possible.

You may not be able to identify a low tire by simply looking at it. Always use a good quality tire pressure gauge to measure the tire's inflation pressure. Please note that a tire that is hot (from being driven) will have a higher pressure measurement than a tire that is cold (from sitting stationary for at least 3 hours and driven less than 1.6 km (1 mile) during that 3 hour period). Allow the tire to cool before

sors.
· In order for the system to correctly monitor tires for underinflation, there should be a total of exactly 4 sensors fitted to each of the four driven wheel positions. There should be no other sensors in the vehicle since this could cause the system to monitor the wrong sensors

measuring the inflation pressure.

In case of an emergency

WARNING - TPMS
· The TPMS cannot alert you to severe and sudden tire damage caused by external factors such as nails or road debris.
· If you feel any vehicle instability, immediately take your foot off the accelerator, apply the brakes gradually and with light force, and slowly move to a safe position off the road.

WARNING - Protecting

This device complies with Industry Canada Standard RSS-

TPMS

210. Operation is subject to the fol-

Tampering with, modifying, or lowing two conditions:

disabling the Tire Pressure 1. This device may not cause harm-

Monitoring System (TPMS) components may interfere with

ful interference, and 2. This device must accept any inter-

the system's ability to warn the

ference received, including inter-

driver of low tire pressure conditions and/or TPMS malfunc-

ference that may cause undesired 3
operation.

tions.

Changes or modifications not expressly approved by the party

responsible for compliance could

void the user's authority to oper- 5
ate the equipment.

In case of an emergency

OVERHEATING

If your temperature gauge indicates overheating, if you experience a loss

If coolant is not boiling out, allow the engine to idle and open the

WARNING - Removing

of power, or if you hear a loud knock-

hood to permit the engine to cool

radiator cap

1 ing or pinging noise, the engine has
probably overheated. Should any of these symptoms occur, use the fol-
2 lowing procedure:

gradually.
If the temperature does not go down with the engine idling, stop the engine and allow sufficient

Do not remove the radiator cap when the engine and radiator are hot. Scalding hot coolant and steam may blow out under

1. Turn on the hazard warning flash-

time for it to cool.

pressure. This could cause seri-

er, then drive to the nearest safe 4. The coolant level should then be

location and stop your vehicle; set

checked. If the level in the reser-

ous injury.

the automatic transaxle in P

(Park), or shift the manual

transaxle to N (Neutral) and apply

the parking brake. 2. Make sure the air conditioner is

voir is low, look for leaks at the radiator hoses and connections, heater hoses and connections, radiator, and water pump. If you find a major leak or another prob-

If the engine frequently overheats, have the cooling system checked and repaired by an Authorized Kia Dealer.

off.

lem that may have caused the

6 3. If coolant or steam is boiling out of

the radiator, stop the engine and

call an Authorized Kia Dealer for assistance.

engine to overheat, do not operate the engine until it has been corrected. Call an Authorized Kia Dealer for assistance. If you do not find a leak or other problem, care-

fully add coolant to the reservoir.

EMERGENCY STARTING
Jump starting
Jump starting can be dangerous if done incorrectly. Therefore, to avoid harm to yourself or damage to your vehicle or battery, follow the jump starting procedures listed on page 6-10. If in doubt, we strongly recommend that you have a competent technician or towing service jump start your vehicle.

CAUTION
Use only a 12-volt jumper system. You can damage a 12-volt starting motor, ignition system, and other electrical parts beyond repair by use of a 24volt power supply (either two 12-volt batteries in series or a 24-volt motor generator set).

WARNING - Battery
Never attempt to check the electrolyte level of the battery as this may cause the battery to rupture or explode causing serious injury.

In case of an emergency

WARNING - Battery

· Keep all flames or sparks
away from the battery. The bat- 1

tery produces hydrogen gas

which may explode if exposed to flame or sparks.

· Do not attempt to jump start

the vehicle if the discharged 3
battery is frozen or if the elec-

trolyte level is low; the battery may rupture or explode.

In case of an emergency

Connecting jumper cables

Connect cables in numerical order and disconnect in reverse order.

Jumper Cables

7 Discharged battery

Booster battery

6 10

OLD046001

Jump starting procedure
1. Make sure the booster battery is 12-volt and that its negative terminal is grounded.
2. If the booster battery is in another vehicle, do not allow the vehicles to touch.
3. Turn off all unnecessary electrical loads.
4. Connect the jumper cables in the exact sequence shown in the previous illustration. First connect one end of a jumper cable to the positive terminal of the discharged battery (1), then connect the other end to the positive terminal on the booster battery (2). Proceed to connect one end of the other jumper cable to the negative terminal of the booster battery (3), then the other end to a solid, stationary, metallic point (for example, the engine lifting bracket) away from the battery (4). Do not connect it to or near any part that moves when the engine is cranked. Do not connect the jumper cable from the negative terminal of the booster battery to the negative terminal of the discharged battery.

Do not allow the jumper cables to contact anything except the correct battery terminals or the correct ground. Do not lean over the battery when making connections.
5. Start the engine of the vehicle with the booster battery and let it run at 2,000 rpm, then start the engine of the vehicle with the discharged battery.
If the cause of your battery discharging is not apparent, you should have your vehicle checked by an Authorized Kia Dealer.
Refer to illustration on page 6-10.

Push-starting
Your manual transaxle-equipped vehicle should not be push-started because it might damage the emission control system.
Vehicles equipped with automatic transaxle cannot be push-started.
Follow the directions in this section for jump-starting.
CAUTION
Never tow a vehicle to start it because the sudden surge forward when the engine starts could cause a collision with the tow vehicle.

In case of an emergency
1 2 3 4 5 6 7 8 9

6 11

In case of an emergency

ELECTRICAL CIRCUIT PROTECTION

Blade type

Normal

Cartridge type

Normal

Blown Blown

This vehicle has two fuse panels, one located in the driver's side knee bolster, the other in the engine compartment near the battery.
If any of your vehicle's lights, accessories, or controls do not work, check the appropriate circuit fuse. If a fuse has blown, the element inside the fuse will be melted.
If the electrical system does not work, first check the driver's side fuse panel.
Always replace a blown fuse with one of the same rating.

If the replacement fuse blows, this indicates an electrical problem. Avoid using the system involved and immediately consult an Authorized Kia Dealer.
Three kinds of fuses are used: blade type for lower amperage rating, cartridge type, and fusible link for higher amperage ratings.

Fusible link
6

Normal

Blown 1VQA4037

Fuses A vehicle's electrical system is pro-

tected from electrical overload dam-

age by fuses.

6 12

In case of an emergency

Fuse replacement

WARNING - Fuse replace-
ment

· Never replace a fuse with any-

thing but another fuse of the

same rating.

· A higher capacity fuse could cause damage and possibly a

fire.

· Never install a wire instead of

1LDA4003

1LDN4022

the proper fuse - even as a temporary repair. It may cause extensive wiring damage and possibly a fire.

Driver-side knee bolster
1. Turn the ignition switch and all other switches off.

If you do not have a spare, use a fuse of the same rating from a circuit you may not need for operating the vehicle, such as the audio fuse.

· Do not use a screwdriver or any other metal object to remove fuses because it may cause a short circuit and damage the system.

2. Pull the suspected fuse straight out. Use the removal tool provided on the cover.
3. Check the removed fuse; replace it if it is blown.

If the headlights or other electrical components do not work and the fuses are OK, check the fuse block in the engine compartment. If a fuse is blown, it must be replaced.

6 7

Spare fuses are provided in the

fuse panel in engine compart-

ment.

4. Push in a new fuse of the same

rating, and make sure it fits tightly

in the clips.

If it fits loosely, consult an Authorized Kia Dealer.

6 13

In case of an emergency

CAUTION

After checking the fuse box in

the engine compartment,

securely install the fuse box

cover. If not, electrical failures

may occur from water leaking

in.

1LDA4005

Engine compartment
5 1. Turn the ignition switch and all
other switches off.

2. Remove the fuse box cover by pressing the taps on both ends

and pulling up.

7 3. Check the removed fuse; replace it

if it is blown.

8 4. Push in a new fuse of the same
rating, and make sure it fits tightly in the clips.
9 If it fits loosely, consult an Authorized
Kia Dealer.

1LDA4006
Main fuse
If the ALT (120A) fuse is blown, it must be removed as follows:
1. Disconnect the negative battery cable.
2. Remove the screws shown in the picture above.
3. Replace the fuse with a new one of the same rating.
4. Reinstall in the reverse order of removal.

6 14

In case of an emergency

Fuse/Relay panel description

Inside the fuse/relay box covers, you can find the fuse/relay label describing fuse/relay name and capacity.

Engine compartment

Driver-side knee bolster

9
2LDN4008/2LDN4007

6 15

In case of an emergency

Engine compartment

Description Fuse rating Protected component

ATM ECU1

20A

Automatic transaxle control

10A

Engine control unit

STOP

15A

Stop light

F/WIPER

R/FOG

20A

Front wiper

10A

Rear fog light

F/FOG LO HDLP

15A

Front fog light

15A

Headlight (low)

HI HDLP

15A

Headlight (high)

A/CON

F/PUMP

10A

Air conditioner

15A

Fuel pump

T/OPEN

FOLD

10A

Trunk lid opener

10A

Outside rearview mirror folding

HORN

10A

Horn

DEICE INJ

15A

Deicer

15A

Injection

SNSR

ECU2

SPARE

10A

O2 sensor

30A

Engine control unit

10A

spare fuse

SPARE SPARE

15A

spare fuse

20A

spare fuse

SPARE

30A

spare fuse

ABS2

ABS1

30A

Anti-lock brake system

30A

Anti-lock brake system

IP B+

50A

In panel B+

Description BLOWER IGN2 IGN1 RAD COND ALT ATM WIPER F/FOG LO HDLP HI HDLP A/CON F/PUMP DRL COND2 HORN MAIN START RAD COND

Fuse rating 30A 30A 30A 30A 20A 120A -

Protected component Blower Ignition Ignition Radiator fan Condenser fan Alternater Automatic transaxle control relay Wiper relay Front fog light relay Headlight relay (low) Headlight relay (high) Air conditioner relay Fuel pump Daytime running light relay Condenser fan relay Horn relay Main relay Start motor relay Radiator fan relay Condenser fan relay

6 16

In case of an emergency

Driver-side knee bolster

Description START SRF/D_LOCK HAZARD A/CON CLUSTER RKE S/HTR C/LIGHTER A/BAG R/WIPER AUDIO ABS ACC/PWR ROOM IGN ECU TAIL RH T/SIG RR/HTR P/WDW LH HTD/MIRR P/WDW RH TAIL LH

Fuse rating 10A 20A 10A 10A 10A 10A 20A 15A 15A 15A 10A 10A 15A 15A 10A 10A 10A 10A 30A 25A 10A 25A 10A

Protected component Start motor Sunroof, Door lock Hazard warning flasher Air conditioner Cluster Remote keyless entry Seat warmer Cigar lighter Air bag Rear wiper Audio Anti-lock brake system Accessory / Power socket Room lamp Ignition Engine control unit Tail light (right) Turn signal light Rear window defroster Power window (left) Outside rearview mirror heater Power window (right) Tail light (left)

Description Fuse rating Protected component

RR/HTR RESISTOR

Rear window defroster relay

Resistor

P/WDW

Power window relay

POWER TAIL

Accessory / Power socket relay

Tail light relay

6 17

In case of an emergency

1. Turn off the engine.

NOTICE

Memory fuse
1
2
3
4
Memory fuse

1LDA4004

2. Turn off the headlights and tail lights.
3. Open the driver-side knee bolster cover and pull up the "ROOM 15A".

· If the memory fuse is pulled up from the fuse panel, the warning chime, audio, clock and intetrior lamps, etc., will not operate. Some items must be reset after replacement. (Refer to "Items to be reset···." on page 7-26)
· Even though the memory fuse is pulled up, the battery can still be discharged by operation of the headlights or other electrical devices.

5 Your vehicle is equipped with a mem-
ory fuse to prevent battery discharge

if your vehicle is parked without being operated for prolonged peri-

ods. Use the following procedures

before parking the vehicle for prolonged period.

6 18

TOWING

In case of an emergency

1LDN4023

2LDA4001

2LDA4002

If emergency towing is necessary, It is acceptable to tow the vehicle

we recommend having it done by an with the rear wheels on the ground authorized Kia dealer or a commer- (without dollies) and the front wheels

cial tow-truck service. Proper lifting off the ground.

and towing procedures are neces- When being towed by a commercial

sary to prevent damage to the vehicle. The use of wheel dollies or flatbed is recommended.
For trailer towing guidelines informa-

tow truck and wheel dollies are not used, the front of the vehicle should always be lifted, not the rear.

CAUTION

2GHA4107
7

tion, refer to section 5 "Driving Tips".

· Do not tow the vehicle backwards with the front wheels on

the ground as this may cause

damage to the vehicle.

· Do not tow with sling-type

equipment. Use wheel lift or

flatbed equipment.

6 19

In case of an emergency

When towing your vehicle in an Tie-down hook emergency without wheel dollies :

1. Set the ignition switch in the ACC

position.

2. Place the transaxle shift lever in N

(Neutral).

3. Release the parking brake.

CAUTION

Failure to place the transaxle shift lever in N (Neutral) may

cause internal damage to the Tie-down hook

5 transaxle.

(for flatbed towing)

OLD046019

· Front · Rear

OLD046020

WARNING

Do not use the hooks under the

front of the vehicle for towing purposes. These hooks are

designed ONLY for transport tie-

OLD046021

down. If the tie-down hooks are used for towing, the tie-down hooks will be damaged and this

Towing with a vehicle other than a tow truck

could lead to serious injury.

If towing is necessary, we recommend you to have it done by an

Authorized Kia dealer or a commer-

cial tow truck service.

6 20

In case of an emergency

If towing service is not available in an Towing in this manner may be done emergency, your vehicle may be only on hard-surfaced roads for a

CAUTION

temporarily towed using a cable or short distance and at low speeds. · Attach a towing strap to the

chain secured to the emergency tow- Also, the wheels, axles, power train,

tow hook.

ing hook under the front or rear of the steering and brakes must all be in · Using a portion of the vehicle

vehicle. Use extreme caution when good condition. towing the vehicle. A driver must be · Do not use the tow hooks to pull a

other than the tow hooks for towing may damage the body

in the vehicle to steer it and operate vehicle out of mud, sand or other

of your vehicle.

the brakes.

conditions from which the vehicle · Use only a cable or chain

cannot be driven out under its own

specifically intended for use

power. · Avoid towing a vehicle heavier than

in towing vehicles. Securely fasten the cable or chain to

the vehicle doing the towing.

the towing hook provided.

· The drivers of both vehicles should

communicate with each other fre-

quently.

· Before emergency towing, check
that the hook is not broken or dam- 6

aged.

· Fasten the towing cable or chain securely to the hook.

· Do not jerk the hook. Apply steady and even force.

· To avoid damaging the hook, do
not pull from the side or at a verti- 9
cal angle. Always pull straight ahead.

6 21

In case of an emergency

WARNING

When your vehicle is being towed by another vehicle

Use extreme caution when tow-
1 ing the vehicle.

other than a tow truck (In case of an emergency)

· Avoid sudden starts or erratic

driving maneuvers which would place excessive stress

on the emergency towing

hook and towing cable or

chain. The hook and towing

· Turn the ignition switch to ACC so the steering wheel isn't locked.
· Place the transaxle shift lever in N (Neutral).
· Release the parking bake.

cable or chain may break and cause serious injury or dam-

· Vehicle equipped with automatic 1LDA4024 transaxles should not exceed 45

age.

· Use a towing strap less than 5 m km/h (28 mph) and should not be

· If the towing vehicle can hardly move, do not forcibly con-

(16 feet) long. Attach a white or red towed more than 80 km (50 miles). cloth (about 30 cm (12 inches) · Vehicle equipped with manual

tinue the towing. Contact an

wide) in the middle of the strap for transmissions should not be towed

Authorized Kia dealer or a

easy visibility.

in excess of 88 km/h (55 mph) and

commercial tow truck service · Drive carefully so that the towing should not be towed more than

for assistance. · Tow the vehicle as straight

strap is not loosened during towing.

645 km (400 miles).

ahead as possible.
8

6 22

· Press the brake pedal with more force than normal since you will have reduced brake performance.
· More steering effort will be required because the power steering system will be disabled.
· If you are driving down a long hill, the brakes may overheat and brake performance will be reduced. Stop often and let the brakes cool off.
CAUTION
To prevent internal damage to the transaxle, never tow your vehicle from the rear (backwards) with all four tires in contact with the surface.

Tips for towing a stuck vehicle
The following methods are effective when your vehicle is stuck in mud, sand or similar substances that prevent the vehicle from being driven out under its own power.
· Remove the soil and sand, etc. from the front and the back of the tires.
· Place a stone or wood under the tires.

In case of an emergency
1 2 3 4 5 6 7 8 9

6 23

In case of an emergency

IF YOU HAVE A FLAT TIRE

Important - use of compact spare tire

your vehicle is equipped with a compact spare tire. This compact spare

tire takes up less space than a regu-

lar-size tire. This tire is smaller than a conventional tire and is designed for

temporary use only.

CAUTION - Compact

1LDN4009

1LDA4010

spare

The spare tire, jack, jack handle, Removing the spare tire

· You should drive carefully

wheel lug nut wrench are stored in the trunk compartment. Move the carpeting out of the way to reach this

Turn the tire hold-down wing bolt counterclockwise.

when the compact spare is in use. The compact spare should be replaced by the

6 equipment.

Store the tire in the reverse order of removal.

proper conventional tire and rim at the first opportunity.

To prevent the spare tire and tools · The operation of this vehicle

from "rattling" while the vehicle is in

is not recommended with

motion, store them properly.

more than one compact spare

tire in use at the same time.

6 24

In case of an emergency

CAUTION - Compact

When using a compact spare tire, · Do not take this vehicle through an

observe the following precautions:

automatic car wash.

spare

· Under no circumstances should · This tire should not be installed on

This spare tire should be used

you exceed 80 km/h (50 mph); a the front axle if the vehicle must be 1

only for VERY short distances.

higher speed could damage the driven in snow or on ice.

Compact spares should NEVER be used for long drives or

tire.

· Do not use the compact spare tire

· Ensure that you drive slowly on any other vehicle because this

extended distances.

enough for the road conditions to tire has been designed especially

avoid all hazards. Any road hazard, for your vehicle.

The compact spare should be inflated to 420 kPa (60 psi).

such as a pothole or debris, could · The compact spare tire's tread life

seriously damage the compact spare.

is shorter than a regular tire. Inspect your compact spare tire

NOTICE

· Any continuous road use of this tire could result in tire failure, loss of

Check the inflation pressure after vehicle control, and possible per-

regularly and replace worn com-
pact spare tires with the same size 5
and design, mounted on the same

installing the spare tire. Adjust it to sonal injury. the specified pressure, as necessary. · Do not exceed the vehicle's maxi-

wheel.

mum load rating or the load-carry-

ing capacity shown on the sidewall of the compact spare tire.

· Avoid driving over obstacles. The compact spare tire diameter is

smaller than the diameter of a con-

ventional tire and reduces the ground clearance approximately

25 mm (1 inch), which could result

in damage to the vehicle.

6 25

In case of an emergency

Changing tires Jacking instructions

WARNING - Changing
tires

The jack is provided for emergency tire changing only.

· Never attempt vehicle repairs in the traffic lanes of a public

Follow jacking instructions to reduce the possibility of personal injury.

road or highway. · Always move the vehicle com-

pletely off the road and onto

the shoulder before trying to

change a tire. The jack should

be used on level firm ground whenever possible. If you can-

not find a firm, level place off

the road, call a towing service company for assistance.

· Be sure to use the correct

front and rear jacking posi-

tions on the vehicle; never use

the bumpers or any other part of the vehicle for jack support.

(Continued)
8

(Continued)
· The vehicle can easily roll off the jack causing serious injury or death. No person should place any portion of their body under a vehicle that is supported only by a jack.
· Do not start or run the engine while the vehicle is on the jack.
· Do not allow anyone to remain in the vehicle while it is on the jack.
· Make sure any children present are in a secure place away from the road and from the vehicle to be raised with the jack.

6 26

In case of an emergency

WARNING - Changing a tire

· To prevent vehicle movement
while changing a tire, always 1

set the parking brake fully, and

always block the wheel diagonally opposite the wheel being

changed.

· It is recommended that the 3
wheels of the vehicle be

1JBA6021

1JBA6504

chocked, and that no person should remain in a vehicle that

Tire replacement

4. Remove the wheel lug nut wrench,

is being jacked.

1. Park on a level surface and apply the parking brake firmly.

jack, jack handle, and spare tire from the vehicle.

2. Shift the shift lever into R 5. Block both the front and rear of the

(Reverse) with manual transaxle

wheel that is diagonally opposite

or P (Park) with automatic

the jack position.

transaxle.

3. Activate the hazard warning flash-

er.

6 27

In case of an emergency

OLD046014

1LDA4015

1LDN4016

6. Loosen the wheel lug nuts coun- 7. Place the jack at the front or rear 8. Insert the jack handle into the jack

terclockwise one turn each, but do not remove any nut until the tire

jacking position closest to the tire you are changing. Place the jack

and turn it clockwise, raising the vehicle until the tire just clears the

has been raised off the ground.
6

at the designated locations under the frame. The jacking positions are plates welded to the frame

ground. This measurement is approximately 30 mm (1.2 in). Before removing the wheel lug

with two tabs and a raised dot to index with the jack.

nuts, make sure the vehicle is stable and that there is no chance for

movement or slippage.

WARNING - Jack location 9. Remove the wheel lug nuts by

To reduce the possibility of

turning them counterclockwise,

injury, be sure to use only the jack provided with the vehicle

then remove the wheel. 10. Mount the spare tire into position

and in the correct jack position;

and install the wheel lug nuts

never use any other part of the

with the beveled edge inward.

vehicle for jack support.

6 28

In case of an emergency

CAUTION

WARNING - Wheel bolts

Your vehicle has metric threads If the bolts are damaged or if

on the wheel bolts and nuts.

non-metric nut is used on a met-

Make certain during wheel ric bolts or vice versa, they may

removal that the same nuts removed are reinstalled - or, if

lose their ability to retain the wheel. This could lead to the

replaced, that nuts with metric loss of the wheel resulting in

threads and the same chamfer configuration are used.

severe injury or death.

Installation of a non-metric

OLD046018
11. Once the wheel lug nuts have been tightened, lower the vehicle fully to the ground and continue to tighten the lug nuts until they are

thread nut on a metric bolt or vice-versa will not secure the wheel to the hub properly and will damage the bolt so that it must be replaced.

To prevent the jack, jack handle, wheel lug nut wrench and spare tire from rattling while the vehicle is in motion, store them properly.

4 5

fully secured. Tighten the wheel lug nuts firmly in a "X" pattern.
If you are unsure of the tightness of the wheel lug nuts, have them checked at the nearest service station. The specified tightening torque is 9~11 kg·m (65-79 lb·ft,

Note that most lug nuts do not have metric threads. Be sure to use extreme care in checking for thread style before installing aftermarket lug nuts or wheels. If in doubt, consult an Authorized Kia Dealer.

WARNING
Check the inflation pressures as soon as possible after installing the spare tire. Adjust it to the specified pressure, if necessary. Refer to Section 8, Specifications.

6 7 8

88-107 N·m). Improperly tight-

ened wheel lug nuts could cause

brake pedal vibration while brak-

ing.

6 29

Maintenance services / 7-2 Maintenance schedule / 7-3

Owner maintenance / 7-7

Engine compartment / 7-10

Engine oil and oil filter / 7-11

Engine cooling system / 7-12 Brakes and clutch / 7-15

Parking brake / 7-16

Power steering / 7-17

Manual transaxle / 7-18

Automatic transaxle / 7-18

Lubricants and fluids / 7-20

Air cleaner / 7-21

Climate control air filter / 7-22 Wiper blades / 7-23

Maintenance

Battery / 7-25 Tires and wheels / 7-28

Exterior care / 7-40

Interior care / 7-44

Maintenance

MAINTENANCE SERVICES

You should exercise the utmost care Owner's responsibility

Repairs and adjustments required as

to prevent damage to your vehicle

a result of improper maintenance or

and injury to yourself whenever performing any maintenance or inspec-

NOTICE

a lack of required maintenance are not covered.

tion procedures.

Maintenance Service and Record We recommend you have your vehi-

Should you have any doubts con- Retention are the owner's responsi- cle maintained and repaired by an

cerning the inspection or servicing of bility.

Authorized Kia Dealer. An Authorized

your vehicle, we strongly recom-

Kia Dealer meets Kia`s high service

mend that you have an Authorized You should retain documents that quality standards and receives tech-

Kia Dealer perform this work.

show proper maintenance has been nical support from Kia in order to pro-

An Authorized Kia Dealer has facto- performed on your vehicle in accor- vide you with a high level of service ry-trained technicians and genuine dance with the scheduled mainte- satisfaction.

Kia parts to service your vehicle nance service charts shown on the

properly. For expert advice and qual- following pages. You need this infority service, see an Authorized Kia mation to establish your compliance

Dealer.

with the servicing and maintenance

6 Inadequate, incomplete or insuffi- requirements of your Kia warranties.

cient servicing may result in opera- Detailed warranty information is pro-

tional problems with your vehicle that vided in your Warranty & Consumer could lead to vehicle damage, an Information manual.

accident, or personal injury.

Maintenance

MAINTENANCE SCHEDULE Engine control system

MAINTENANCE

Kilometers or time in months, whichever comes first

INTERVALS × 1,000 km 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128

MAINTENANCE

ITEM

# Months 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64

Engine oil & engine oil filter (1)

Replace every 6,000 km or 6 months.

Drive belts (tension) Cooling system hoses & connections

Engine coolant Fuel filter

(1)

I RI

Fuel tank cap, lines, EVAP canister and hoses

Fuel tank air filter

Air cleaner filter Ignition wires

(2)

I RI

Spark plugs

Platinum coated Iridium coated

Replace every 160,000 km

Idle speed Valve clearance (if equipped) Engine timing belt

Maintenance

MAINTENANCE SCHEDULE (CONTINUED)

Chassis and body

MAINTENANCE

Kilometers or time in months, whichever comes first

INTERVALS × 1,000 km 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128

MAINTENANCE

ITEM

# Months 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64

Air conditioner compressor operation &

refrigerant amount (if equipped)

Exhaust pipes, heat shield & mountings

Front suspension ball joints

Brakes/clutch fluid

(1)

III

I IRI

I IR

Front brake pads & discs

(3)

Rear brake pads & discs/drums (3)

III

Parking brake

Brake lines & connections

(including booster)

Manual transaxle oil

(1)

IRI

I IRI

I RI

I IR

Clutch & brake pedal free play

III

Maintenance

MAINTENANCE SCHEDULE (CONTINUED)

Chassis and body (Continued)

MAINTENANCE

Kilometers or time in months, whichever comes first

INTERVALS × 1,000 km 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128

MAINTENANCE

ITEM

# Months 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64

Automatic transaxle fluid

(1)

IRI

I RI

Chassis & underbody bolts & nuts Tire condition & inflation pressure

Wheel alignment

(4)

Tire rotation

Inspect when abnormal condition noted

Rotate the tires every 12,000 km

Steering operation & linkage Power steering fluid & lines

Driveshaft dust boots Seat belts, buckles & anchors

Lock, hinges & hood latch

L L LLL LL L L L L LL LL L

Maintenance

Chart symbols:

I- Inspect these items and their related parts. If necessary, correct, clean, refill, adjust or replace.

1 R- Replace or change.
L- Lubricate.

(1) Refer to the lubricant and coolant specifications in the Owner's Manual. (2) More frequent maintenance is required if driving under dusty conditions.

(3) More frequent maintenance is required if the vehicle is operated under any of the following conditions: a. Short-distance driving.

b. Driving on dusty roads. c. Extensive idling or slow-speed driving in stop-and-go traffic.

(4) If necessary, rotate and balance the wheels.
5
* Note: Check the engine oil and coolant levels every week.

Maintenance

OWNER MAINTENANCE

Owner maintenance schedule When you stop for fuel:

While operating your vehicle:

The following lists are vehicle checks · Check the engine oil level.

· Note any changes in the sound of

and inspections that should be per- · Check coolant level in coolant formed by the owner or an reservoir.

the exhaust or any smell of

exhaust fumes in the vehicle.

Authorized Kia Dealer at the fre-

· Check for vibrations in the steering

quencies indicated to help ensure safe, dependable operation of your vehicle.

WARNING - Radiation
coolant

wheel. Notice any increased steering effort or looseness in the steer-

ing wheel, or change in its straight-

Any adverse conditions should be brought to the attention of your dealer as soon as possible.
These Owner Maintenance Checks are generally not covered by warranties and you may be charged for

Be careful when checking your engine coolant level when the engine is hot. Scalding hot coolant and steam may blow out under pressure. This could cause serious injury.

ahead position.
· Notice if your vehicle constantly turns slightly or "pulls" to one side when traveling on smooth, level road.
· When stopping, listen and check

3 4 5

labor, parts and lubricants used.

· Check the windshield washer fluid level.

for strange sounds, pulling to one

side, increased brake pedal travel or "hard-to-push" brake pedal.

· Look for low or under-inflated tires. · If any slipping or changes in the

operation of your transaxle occurs, 7

check the transaxle fluid level.

· Check automatic transaxle P (Park) function.

· Check parking brake.
· Check for fluid leaks under your 9
vehicle (water dripping from the air conditioning system after use is normal).

Maintenance

At least monthly:

At least twice a year

At least once a year :

· Check coolant level in the engine (i.e., every Spring and Fall) :

· Clean body and door drain holes.

coolant reservoir.

· Check radiator, heater and air con- · Lubricate door hinges and checks,

· Check the operation of all exterior ditioning hoses for leaks or da- and hood hinges.

lights, including the stoplights, turn mage.

· Lubricate door and hood locks and

2 3

signals and hazard warning flashers.
· Check the inflation pressures of all tires including the spare.

· Check windshield washer spray and wiper operation. Clean wiper blades with clean cloth dampened with washer fluid.
· Check headlight alignment.

latches.
· Lubricate door rubber weatherstrips.
· Check the air conditioning system.

· Check muffler, exhaust pipes, shields and clamps.

· Check the power steering fluid level.

· Check the lap/shoulder belts for wear and function.

· Inspect and lubricate automatic transaxle linkage and controls.

· Check for worn tires and loose · Clean battery and terminals.

wheel lug nuts.

· Check the brake fluid level.

Owner maintenance precautions
Improper or incomplete service may result in problems. This section gives instructions only for the maintenance items that are easy to perform.
As explained earlier in this section, several procedures can be done only by an Authorized Kia Dealer with special tools.
NOTICE
Improper owner maintenance during the warranty period may affect warranty coverage. For details, read the separate Kia Warranty & Consumer Information Manual provided with the vehicle. If you're unsure about any servicing or maintenance procedure, have it done by an Authorized Kia Dealer.

WARNING - Maintenance
work
· Performing maintenance work on a vehicle can be dangerous. You can be seriously injured while performing some maintenance procedures. If you lack sufficient knowledge and experience or the proper tools and equipment to do the work, have it done by an Authorized Kia Dealer.
· Working under the hood with the engine running is dangerous. It becomes even more dangerous when you wear jewelry or loose clothing. These can become entangled in moving parts and result in injury. Therefore, if you must run the engine while working under the hood, make certain that you remove all jewelry (especially rings, bracelets, watches, and necklaces) and all neckties, scarves, and similar loose clothing before getting near the engine or cooling fans.

Maintenance
1 2 3 4 5 6 7 8 9
79

Maintenance ENGINE COMPARTMENT
1 2 3 4 5 6 7 8 9
7 10

1. Power steering fluid reservoir 2. Engine oil filler cap 3. Brake fluid reservoir 4. Air cleaner 5. Fuse box 6. Negative battery terminal 7. Positive battery terminal 8. Auto transaxle oil dipstick
(if equipped) 9. Radiator cap 10. Engine oil dipstick 11. Engine coolant reservoir 12. Windshield washer fluid reservoir
OLD056002

Maintenance

ENGINE OIL AND OIL FILTER

Changing the engine oil and filter

Have engine oil and filter changed by an authorized Kia dealer according

to the Maintenance Schedule at the

beginning of this section.

WARNING

Used engine oil may cause irri-

OHD076004R

tation or cancer of the skin if left 1LDN5003 in contact with the skin for pro-

Checking the engine oil level If it is near or at L, add enough oil to longed periods of time. Used

1. Be sure the vehicle is on level bring the level to F. Do not overfill. ground.

engine oil contains chemicals that have caused cancer in lab-

2. Start the engine and allow it to reach normal operating temperature.
3. Turn the engine off and wait for a

Use only the specified engine oil. (Refer to "Recommended Lubricants" in section 8.)

oratory animals. Always protect your skin by washing your hands thoroughly with soap and warm water as soon as possible after handling used oil.

6 7

few minutes (about 5 minutes) for

the oil to return to the oil pan.

4. Pull the dipstick out, wipe it clean,

and re-insert it fully.

5. Pull the dipstick out again and

check the level. The level should

be between F and L.

7 11

Maintenance

ENGINE COOLING SYSTEM

The high-pressure cooling system Checking the coolant level

has a reservoir filled with year-round

antifreeze coolant. The reservoir is
1 filled at the factory.

WARNING - Removing
radiator cap

2 3

Check the antifreeze protection and coolant level at least once a year, at the beginning of the winter season, and before traveling to a colder climate.

· Never attempt to remove the radiator cap while the engine is operating or hot. Doing so might lead to cooling system and engine damage and could

result in serious personal

injury from escaping hot coolant or steam.

· Turn the engine off and wait

until it cools down. Even then,

use extreme care when

removing the radiator cap. Wrap a thick towel around it,

and turn it counterclockwise

slowly to the first stop. Step back while the pressure is

released from the cooling sys-

tem. When you are sure all the

pressure has been released,

press down on the cap, using a thick towel, and continue

turning counterclockwise to

remove it.

(Continued)

(Continued)
· Even if the engine is not operating, do not remove the radiator cap or the drain plug while the engine and radiator are hot. Hot coolant and steam may still blow out under pressure, causing serious injury.

7 12

Maintenance

Recommended engine coolant

For mixture percentage, refer to the

· Use only soft (de-mineralized) following table.

water in the coolant mixture. · The engine in your vehicle has alu-

Mixture Percentage (volume)

minum engine parts and must be

Ambient

Full

protected by an ethylene-glycolbased coolant to prevent corrosion and freezing.

Temperature

Coolant Solution

Water

· DO NOT USE alcohol or methanol

-15°C (5°F)

Low

coolant or mix them with the spec- -25°C (-13°F)

OLD056008

ified coolant.

-35°C (-31°F)

Check the condition and connections of all cooling system hoses and heater hoses. Replace any swollen or deteriorated hoses.

· Do not use a solution that contains more than 60% antifreeze or less than 35% antifreeze, which would reduce the effectiveness of the solution.

-45°C (-49°F)

The coolant level should be filled

5 6

between F and L marks on the side

of the coolant reservoir when the engine is cool.

If the coolant level is low, add enough

specified coolant to provide protec-

tion against freezing and corrosion.

Bring the level to F, but do not overfill. If frequent additions are required,

see an Authorized Kia Dealer for a

cooling system inspection.

7 13

Maintenance

Changing the coolant

Have coolant changed by an author-

ized Kia dealer according to the Maintenance Schedule at the begin-

ning of this section.

2
CAUTION

Put a thick cloth or fabric

around the radiator cap before

refilling the coolant in order to

OLD057007N prevent the coolant from over-

flowing into engine parts such

WARNING

as generator.

Do not remove the radiator cap

6 when the engine and radiator

are hot. Scalding hot coolant

and steam may blow out under pressure. This could cause seri-

ous injury.

7 14

Maintenance

BRAKES AND CLUTCH (IF EQUIPPED)

If the level is low, add fluid to the MAX level. The level will fall with

WARNING

accumulated mileage. This is a nor- In the event the brake system

mal condition associated with the requires frequent additions of 1
wear of the brake linings. If the fluid fluid, the vehicle should be

level is excessively low, have the inspected by an Authorized Kia brake system checked by an Dealer.

Authorized Kia Dealer.

Use only the specified brake/clutch

WARNING

fluid. (Refer to "Recommended 1LDA5020 Lubricants" in section 8.) Checking brake/clutch fluid

When changing and adding brake/clutch fluid, handle it carefully. Do not let it come in

level

Never mix different types of fluid.

contact with your eyes. If 5

Check the fluid level in the reservoir

brake/clutch fluid should come

periodically. The fluid level should be between MAX and MIN marks on the

in contact with your eyes, immediately flush them with a large

side of the reservoir.

quantity of fresh tap water. Have

Before removing the reservoir cap and adding brake/clutch fluid, clean

your eyes examined by a doctor as soon as possible.

the area around the reservoir cap thoroughly to prevent brake/clutch

fluid contamination.

7 15

Maintenance

PARKING BRAKE

CAUTION

Do not allow brake/clutch fluid

to contact the vehicle's body paint, as paint damage will

result. Brake/clutch fluid, which
2 has been exposed to open air

for an extended time should

never be used as its quality cannot be guaranteed. It should be

thrown out. Don't put in the

wrong kind of fluid. For example, just a few drops of mineralbased oil, such as engine oil, in

OLD036030
Checking the parking brake

5 your brake clutch system can Check the stroke of the parking

damage brake clutch system brake by counting the number of

6 parts.

"clicks'' heard while fully applying it from the released position. Also, the

parking brake alone should securely

hold the vehicle on a fairly steep grade. If the stroke is more or less

than specified, have the parking

brake adjusted by an Authorized Kia

Dealer.

9
Stroke : 7~8 "clicks'' at a force of 20 kg (44 lbs, 196 N).

7 16

Maintenance

POWER STEERING

In the event the power steering sys- Power steering hose

tem requires frequent addition of fluid, the vehicle should be inspected by an Authorized Kia Dealer.

Check the connections for oil leaks, severe damage and the twists in the power steering hose before driving.

CAUTION

· To avoid damage to the power

steering pump, do not operate the vehicle for prolonged peri-

ods with a low power steering

1LDA5018

fluid level.

Checking the power steering fluid level

· Never start the engine when the reservoir tank is empty.
· When adding fluid, be careful

With the vehicle on level ground,

that dirt does not get into the

check the fluid level in the power steering reservoir periodically. The fluid should be between MAX and MIN marks on the side of the reservoir at the normal temperature.

tank.
· Too little fluid can make the steering wheel heavier or strange noise can be generated.

6 7

Before adding power steering fluid, thoroughly clean the area around the reservoir cap to prevent power steering fluid contamination.

· The use of the non-specified fluid could reduce the effectiveness of the power steering wheel and cause damage to it.

8 9

If the level is low, add fluid to the

MAX level.

Use only the specified power steer-

ing fluid. (Refer to "Recommended

Lubricants" in section 8.)

7 17

Maintenance

MANUAL TRANSAXLE

AUTOMATIC TRANSAXLE

(IF EQUIPPED)

Changing the manual

transaxle fluid Have manual transaxle fluid checked

and changed by an authorized Kia
2 dealer according to the Maintenance

Schedule at the beginning of this

3 section.

2. After the transaxle is warmed up sufficiently (fluid temperature 70~80 °C (158~176 °F)), for example by 10 minutes usual driving, shift the selector lever through all positions then place the selector lever in N (Neutral) or P (Park) position.

1LDA5008

Checking the automatic

transaxle fluid level

The automatic transaxle fluid level should be checked regularly.

Keep the vehicle on the level ground with the parking brake applied and

check the fluid level according to the

following procedure. 1. Place the selector lever in N

(Neutral) position and confirm the

engine is running at normal idle

speed.

7 18

Maintenance

OHD076045N
3. Confirm that the fluid level is in "HOT" range on the level gauge. If the fluid level is lower, add the specified fluid from the fill hole. If the fluid level is higher, drain the fluid from the drain hole.
4. If the fluid level is checked in cold condition (fluid temperature 20~ 30 °C (68~86 °F) add the fluid to "COLD (C)" line and then recheck the fluid level according to the above step 2.

WARNING - Transaxle
fluid The transaxle fluid level should be checked when the engine is at normal operating temperature. This means that the engine, radiator, radiator hose and exhaust system etc., are very hot. Exercise great care not to burn yourself during this procedure.
CAUTION
· Low fluid level causes transaxle slippage. Overfilling can cause foaming, loss of fluid and transaxle malfunction.
· The use of a non-specified fluid could result in transaxle malfunction and failure.
WARNING - Parking brake
To avoid sudden movement of the vehicle, apply parking brake and depress the brake pedal before moving the shift lever.

NOTICE

"COLD (C)" scale is for reference

only and should NOT be used to determine transaxle fluid level.

NOTICE

New automatic transaxle fluid

should be red. The red dye is added so the assembly plant can identify it

as automatic transaxle fluid and dis-

tinguish it from engine oil or antifreeze. The red dye, which is not

an indicator of fluid quality, is not

permanent. As the vehicle is driven, 5

the automatic transaxle fluid will

begin to look darker. The color may eventually appear light brown.

Therefore, have an Authorized Kia

dealer change the automatic transaxle fluid according to the

Scheduled Maintenance at the

beginning of this section.

Changing the automatic transaxle fluid

Have automatic transaxle fluid changed by an authorized Kia dealer according to the Maintenance Schedule at the beginning of this section.

7 19

Maintenance

LUBRICANTS AND FLUIDS

Body lubrication

WARNING

All moving points of the body, such

· Do not use radiator coolant or antifreeze in the washer fluid

as door hinges, hood hinges, and locks, should be lubricated each time

reservoir.

the engine oil is changed. Use a non-

· Radiator coolant can severely freezing lubricant on locks during obscure visibility when cold weather.

sprayed on the windshield Make sure the engine hood second-

and may cause loss of vehicle ary latch keeps the hood from open-

control or damage to paint ing when the primary latch is

1LDA5021

and body trim. · Windshield washer fluid

released.

Checking the washer fluid

agents contain some amounts

5 level

The reservoir is translucent so that

you can check the level with a quick visual inspection.

of alcohol and can be flammable under certain circumstances. Do not allow sparks or flame to contact the washer fluid or the washer fluid reser-

Check the fluid level in the washer
7 fluid reservoir and add fluid if neces-

voir. Damage to the vehicle or it's occupants could occur.

8 9

sary. Plain water may be used if washer fluid is not available. However, use washer solvent with antifreeze characteristics in cold climates to prevent freezing.

· Windshield washer fluid is poisonous to humans and animals. Do not drink and avoid contacting windshield washer fluid. Serious injury or death

could occur.

7 20

AIR CLEANER

CAUTION
· Do not drive with the air cleaner removed; this will result in excessive engine wear.
· Driving without an air cleaner encourages backfiring, which could cause a fire in the engine compartment.

1LDA5010
Element cleaning
This element may be air cleaned or replaced, depending on its condition. Unless it is very dirty, merely shake it to remove foreign particles. Each time this filter is inspected, wipe the inside of the air cleaner housing and cover with a damp cloth. If the vehicle is operated in extremely dusty or sandy areas, clean or replace this element more often than at the usual recommended intervals.

Maintenance
1 2 3 4 5 6 7 8 9
7 21

Maintenance

CLIMATE CONTROL AIR FILTER (IF EQUIPPED)

Outside air

Recirculated

air

The climate control air filter should be replaced every 15,000 km. If the vehicle is operated in the severely air-polluted cities or on dusty rough roads for a long periods, it should be inspected more frequently and replaced earlier.

Blower

Climate control

air filter

EvaporatorHeater core

core

1LDA5047

The climate control air filter installed

behind the glove box filters the dust or other pollutants that come into the

vehicle from the outside through the
6 heating and air conditioning system.
If dust or other pollutants accumulate

in the filter over a period of time, the air flow from the air vents may

decrease, resulting in moisture accu-

mulation on the inside of the windshield even when the outside (fresh)

are position is selected. If this hap-

pens, have the climate control air filter replaced by an Authorized Kia

Dealer.

7 22

Maintenance

WIPER BLADES

Contamination of either the wind- Windshield wiper blade

shield or the wiper blades with for- replacement

eign matter can reduce the effectiveness of the windshield wipers. Common sources of contamination are insects, tree sap, and hot wax

When the wipers no longer clean adequately, the blades may be worn or cracked, and require replacement.

treatments used by some commer-

cial car washes. If the blades are not

CAUTION

wiping properly, clean both the win- To prevent damage to the wiper dow and the blades with a good arms or other components, do

cleaner or mild detergent, and rinse not attempt to move the wipers

1LDA5022 thoroughly with clean water.

manually.

Wiper blade maintenance

NOTICE
Commercial hot waxes applied by automatic car washes have been known to make the windshield difficult to clean.

CAUTION
To prevent damage to the wiper blades, do not use gasoline, kerosene, paint thinner, or other solvents on or near them.

CAUTION
The use of a non-specified wiper blade could result in wiper malfunction and failure.

5 6

7 23

Maintenance

1LDA5023

1LDA5024

1LDA5025

1. Raise the wiper arm and turn the 2. Compress the clip and slide the 3. Lift it off the arm.

wiper blade assembly to expose the plastic locking clip.

blade assembly downward.

4. Install the blade assembly in the reverse order of removal.

CAUTION

Do not allow the wiper arm to
7 fall against the windshield.

7 24

BATTERY
WARNING - Battery
dangers
Always read the following instructions carefully when handling a battery.
Keep lighted cigarettes and all other flames or sparks away from the battery.
Hydrogen, which is a highly combustible gas, is always present in battery cells and may explode if ignited.
Keep batteries out of the reach of children because batteries contain highly corrosive SULFURIC ACID. Do not allow battery acid to contact your skin, eyes, clothing or paint finish.
(Continued)

(Continued)
If any electrolyte gets into your eyes, flush your eyes with clean water for at least 15 minutes and get immediate medical attention. If possible, continue to apply water with a sponge or cloth until medical attention is received.
If electrolyte gets on your skin, thoroughly wash the contacted area. If you feel a pain or a burning sensation, get medical attention immediately.
Wear eye protection when charging or working near a battery. Always provide ventilation when working in an enclosed space.
(Continued)

Maintenance

(Continued)

· When lifting a plastic-cased

battery, excessive pressure on the case may cause battery

acid to leak, resulting in person-

al injury. Lift with a battery carrier or with your hands on

opposite corners.

· Never attempt to charge the 3

battery when the battery cables

are connected. · The electrical ignition system

works with high voltage. Never

touch these components with 5
the engine running or the igni-

tion switched on.
6

7 25

Maintenance

Battery recharging

Items to be reset after the battery

Your vehicle has a maintenance-free, calcium-based battery.
· If the battery becomes discharged

has been discharged or the battery has been disconnected.
· Clock (See section 3)

in a short time (because, for exam- · Climate control system

ple, the headlights or interior lights (See section 4)

were left on while the vehicle was · Audio (See section 3)

not in use), recharge it by slow · Sunroof (See section 3) charging (trickle) for 10 hours.

· If the battery gradually discharges

1LDE5028

For best battery service :

5 · Keep the battery securely mount-

because of high electric load while the vehicle is being used, recharge it at 20-30A for two hours.

ed.

6 · Keep the battery top clean and dry.

· Keep the terminals and connec-

tions clean, tight, and coated with petroleum jelly or terminal grease.

· Rinse any spilled electrolyte from

the battery immediately with a

solution of water and baking soda.

· If the vehicle is not going to be used for an extended time, discon-

nect the battery cables.

7 26

Maintenance

WARNING - Recharging

(Continued)

CAUTION

battery

· Disconnect the battery charg- · Before performing mainte-

When recharging the battery, observe the following precau-

er in the following order. 1. Turn off the battery charger

nance or recharging the battery, turn off all accessories

tions: · The battery must be removed

main switch. 2. Unhook the negative clamp

and stop the engine. · The negative battery cable

from the vehicle and placed in

from the negative battery ter-

must be removed first and

an area with good ventilation. · Do not allow cigarettes,

minal. 3. Unhook the positive clamp

installed last when the battery is disconnected.

sparks, or flame near the battery.

from the positive battery terminal.

· Watch the battery during

charging, and stop or reduce

the charging rate if the battery

cells begin gassing (boiling) violently or if the temperature

of the electrolyte of any cell

exceeds 49 °C (120 °F).

· Wear eye protection when

checking the battery during charging.

(Continued)
9

7 27

Maintenance

TIRES AND WHEELS

Tire care

For proper maintenance, safety, and

maximum fuel economy, you must always maintain recommended tire

inflation pressures and stay within

the load limits and weight distribution recommended for your vehicle.

3 Recommended cold tire infla-

tion pressures

4 All tire pressures (including the

1LDN6001

spare) should be checked every day All specifications (sizes and pres-

when the tires are cold. "Cold Tires" sures) can be found on a label means the vehicle has not been driv- attached to the vehicle.

en for at least three hours or driven

6 less than 1.6 km (one mile).

WARNING - Tire underin-

Recommended pressures must be maintained for the best ride, top vehicle handling, and minimum tire wear.

flation Severe underinflation (70 kPa

(10 psi) or more) can lead to

severe heat build-up, causing blowouts, tread separation and

other tire failures that can result

in the loss of vehicle control leading to severe injury or

death. This risk is much higher

on hot days and when driving

for protracted periods at high

speeds.

CAUTION
· Underinflation also results in excessive wear, poor handling and reduced fuel economy. Wheel deformation also is possible. Keep your tire pressures at the proper levels. If a tire frequently needs refilling, have it checked by an Authorized Kia Dealer.
· Overinflation produces a harsh ride, excessive wear at the center of the tire tread, and a greater possibility of damage from road hazards.

7 28

Maintenance

CAUTION
· Warm tires normally exceed recommended cold tire pressures by 28 to 41 kPa (4 to 6 psi). Do not release air from warm tires to adjust the pressure or the tires will be underinflated.
· Be sure to reinstall the tire inflation valve caps. Without the valve cap, dirt or moisture could get into the valve core and cause air leakage. If a valve cap is missing, install a new one as soon as possible.
WARNING - Tire Inflation
Overinflation or underinflation can reduce tire life, adversely affect vehicle handling, and lead to sudden tire failure. This could result in loss of vehicle control and potential injury.

CAUTION - Tire pressure
Always observe the following:
· Check tire pressure when the tires are cold. (After vehicle has been parked for at least three hours or hasn't been driven more than 1.6 km (one mile) since startup.)
· Check the pressure of your spare tire each time you check the pressure of other tires.
· Never overload your vehicle. Be careful not to overload a vehicle luggage rack if your vehicle is equipped with one.
· Worn, old tires can cause accidents. If your tread is badly worn, or if your tires have been damaged, replace them.

Checking tire inflation pressure

Check your tires once a month or more.

Also, check the tire pressure of the

spare tire.

How to check

Use a good quality gage to check tire

pressure. You can not tell if your tires are properly inflated simply by look-

ing at them. Radial tires may look

properly inflated even when they're underinflated.

Check the tire's inflation pressure
when the tires are cold. - "Cold" 6

means your vehicle has been sitting

for at least three hours or driven no more than 1.6 km (1 mile).

Remove the valve cap from the tire

valve stem. Press the tire gage firm- 8

ly onto the valve to get a pressure

measurement. If the cold tire inflation pressure matches the recommended

pressure on the tire and loading

information label, no further adjust-

ment is necessary. If the pressure is

low, add air until you reach the rec-

ommended amount.

7 29

Maintenance

If you overfill the tire, release air by Do not include compact spare tire in rotation. pushing on the metal stem in the center of the tire valve. Recheck the tire
1 pressure with the tire gage. Be sure
to put the valve caps back on the valve stems. They help prevent leaks
2 by keeping out dirt and moisture.

3 Tire rotation

To equalize tread wear, it is recom- Directional tires (if equipped)

mended that the tires be rotated every 12,000 km (7,500 miles) or

sooner if irregular wear develops.

5 During rotation, check the tires for
correct balance.

CBGQ0707

When rotating tires, check for uneven wear and damage. Abnormal wear is

usually caused by incorrect tire pres-

CBGQ0707A

7 sure, improper wheel alignment, out- Disc brake pads should be inspected
of-balance wheels, severe braking or for wear whenever tires are rotated.

8 9

severe cornering. Look for bumps or bulges in the tread or side of tire. Replace the tire if you find either of these conditions. Replace the tire if fabric or cord is visible. After rotation,

Rotate radial tires that have an asymmetric tread pattern only from front to rear and not from right to left.

be sure to bring the front and rear tire

pressures to specification and check

lug nut tightness.

Refer to Section 8, Specifications.

7 30

WARNING
· Do not use the temporary spare tire for tire rotation.
· Do not mix bias ply and radial ply tires under any circumstances. This may cause unusual handling characteristics that could result in death, severe injury, or property damage.

Maintenance

Tread wear indicator

WARNING - Replacing

(Continued)

tires

· The use of any other tire size

· Driving on worn-out tires is very hazardous and will reduce braking effectiveness, steering accuracy, and traction.

or type may seriously affect ride, handling, ground clear-

ance, stopping distance, body

to tire clearance, snow tire 2
clearance, and speedometer

reliability.

Tire replacement

1LDA5026

If the tire is worn evenly, a tread wear indicator will appear as a solid band across the tread. This shows there is less than 1.6 mm (1/16 inch) of tread left on the tire. Replace the tire when this happens.

· Your vehicle is equipped with tires designed to provide for safe ride and handling capability. Do not use a size and type of tire and wheel that is different from the one that is originally installed on your vehicle. It can affect the safety and performance of your vehicle, which could lead to handling failure or rollover and serious injury. When replacing

· It is best to replace all four tires at the same time. If that is not possible, or necessary, then replace the two front or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle's handling.

3 4 5 6 7

Do not wait for the band to appear

the tires, be sure to equip all

across the entire tread before replacing the tire.

four tires with the tire and wheel of the same size, type,

tread, brand and load-carrying

capacity.

(Continued)

7 31

Maintenance

Compact spare tire replace-

Wheel alignment and tire

Wheel replacement

ment (if equipped)

balance

When replacing the metal wheels for

A compact spare tire has a shorter The wheels on your vehicle were any reason, make sure the new tread life than a regular size tire. aligned and balanced carefully at the wheels are equivalent to the original

Replace it when you can see the factory to give you the longest tire life factory units in diameter, rim width

tread wear indicator bars on the tire. and best overall performance.

and offset.

The replacement compact spare tire In most cases, you will not need to

3 4 5

should be the same size and design tire as the one provided with your new Kia and should be mounted on the same compact spare tire wheel. The compact spare tire is not designed to be mounted on a regular size wheel, and the compact spare tire wheel is not designed for mounting a regular size tire.

have your wheels aligned again. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset.
If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced.

WARNING
A wheel that is not the correct size may adversely affect wheel and bearing life, braking and stopping abilities, handling characteristics, ground clearance, body-to-tire clearance, snow chain clearance, speedometer

CAUTION

calibration, headlight aim and bumper height.

Improper wheel weights can damage your vehicle's alu-

minum wheels. Use only

approved wheel weights.

7 32

Maintenance

Tire maintenance

2. Tire size designation

In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignement.

When you have new tires installed,

make sure they are balanced. This

will increase vehicle ride comfort and

A tire's sidewall is marked with a tire

5,6

size designation. You will need this

information when selecting replace- 1

ment tires for your car. The following

explains what the letters and numbers in the tire size designation

mean.

Example tire size designation:

tire life. Additionally, a tire should

(These numbers are provided as an

always be rebalanced if it is removed

from the wheel.

example only; your tire size designaI030B04JM tor could vary depending on your

Tire sidewall labeling

vehicle.)

Tire traction

This information identifies and P195/60R15 87H

Tire traction can be reduced if you drive on worn tires, tires that are improperly inflated or on slippery road surfaces. Tires should be replaced when tread wear indicators appear. To reduce the possiblity of

describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

P - Applicable vehicle type (tires marked with the prefix "P'' are intended for use on passenger cars or light trucks; however, not all tires have this marking).

6 7

losing control, slow down whenever there is rain, snow or ice on the road. 1. Manufacturer or brand name

195 - Tire width in millimeters. 60 - Aspect ratio. The tire's section

Manufacturer or Brand name is shown.

height as a percentage of its

width.

R - Tire construction code (Radial).

15 - Rim diameter in inches.

7 33

Maintenance

87 - Load Index, a numerical code Tire speed ratings

3. Checking tire life (TIN : Tire

associated with the maximum The chart below lists many of the dif-

Identification Number)

load the tire can carry.

ferent speed ratings currently being Any tires that are over 6 years, based

1 H - Speed Rating Symbol. See the used for passenger cars. The speed on the manufacturing date, tire

speed rating chart in this section rating is part of the tire size designa- strength and performance, decline

for additional information.

tion on the sidewall of the tire. This with age naturally (even unused symbol corresponds to that tire's spare tires). Therefore, the tires

Wheel size designation

designed maximum safe operating (including the spare tire) should be

speed.

replaced by new ones. You can find

Wheels are also marked with impor-

the manufacturing date on the tire

tant information that you need if you

ever have to replace one. The following explains what the letters and

Speed Rating Symbol

Maximum Speed

sidewall (possibly on the inside of the wheel), displaying the DOT Code. The DOT Code is a series of num-

numbers in the wheel size designa-

5 tion mean.

180 km/h (112 mph)

bers on a tire consisting of numbers and English letters. The manufactur-

190 km/h (118 mph)

ing date is designated by the last four

6 Example wheel size designation:
6.0JX15

210 km/h (130 mph)

digits (characters) of the DOT code.

240 km/h (149 mph)

7
6.0 - Rim width in inches.

Above 240 km/h (149 mph) DOT : XXXX XXXX OOOO

The front part of the DOT means a

J - Rim contour designation. 15 - Rim diameter in inches.

plant code number, tire size and tread pattern and the last four numbers indicate week and year manu-

factured. For example:

DOT XXXX XXXX 1606 represents that the tire was produced in the 16th week of 2006.

7 34

Maintenance

WARNING

5. Maximum permissible inflation Tread wear

pressure

The tread wear grade is a compara-

Tires degrade over time, even This number is the greatest amount tive rating based on the wear rate of
when they are not being used. of air pressure that should be put in the tire when tested under controlled 1

Regardless of the remaining the tire. Do not exceed the maximum conditions on a specified govern-

tread, it is recommended that tires generally be replaced after

permissible inflation pressure. Refer ment test course. For example, a tire to the Tire and Loading Information graded 150 would wear one-and-a-

six (6) years of normal service. label for recommended inflation half times as well on the government

Heat caused by hot climates or pressure. frequent high loading conditions

course as a tire graded 100.

The relative performance of tires

can accelerate the aging process. Failure to follow this 6. Maximum load rating

depends upon the actual conditions of their use. However, performance

warning can result in sudden tire This number indicates the maximum may differ from the norm because of

failure, which could lead to a loss of control and an accident

load in kilograms and pounds that variations in driving habits, service can be carried by the tire. When practices and differences in road

involving serious injury or death. replacing the tires on the vehicle, characteristics and climate.

4. Tire ply composition and material

always use a tire that has the same load rating as the factory installed tire.

These grades are molded on the side-walls of passenger vehicle tires. The tires available as standard or optional equipment on your vehicles

6 7

The number of layers or plies of rub- 7. Uniform tire quality grading

may vary with respect to grade.

ber-coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. The letter "R" means radial ply construction; the letter "D" means diagonal or bias ply construction; and the

The following information relates to the tire grading system developed by the Canadian Motor Vehicle Safety Standard (CMVSS) for grading tires by tread wear, traction and temperature performance.

8 9

letter "B" means belted-bias ply con-

struction.

7 35

Maintenance

Traction - AA, A, B & C

Tire terminology and defini-

The traction grades, from highest to

WARNING - Tire

tions

lowest, are AA, A, B and C. The grades represent the tires ability to

temperature The temperature grade for this

Air Pressure: The amount of air inside the tire pressing outward on

stop on wet pavement as measured tire is established for a tire that the tire. Air pressure is expressed in

under controlled conditions on specified government test surfaces of

is properly inflated and not overloaded. Excessive speed,

pounds per square inch (psi) or kilopascal (kPa).

3 4 5

asphalt and concrete. A tire marked C may have poor traction performance.
Temperature -A, B & C
The temperature grades are A (the highest), B and C. The grades represent the tire's resistance to the gen-

underinflation, or excessive loading, either separately or in combination, can cause heat build-up and possible sudden tire failure. This can cause loss of vehicle control and serious injury or death.

Accessory Weight: This means the combined weight of optional accessories. Some examples of optional accessories are, automatic transmission, power seats, and air conditioning.
Aspect Ratio: The relationship of a

eration of heat and its ability to dissi-

tire's height to its width.

pate heat when tested under con-
6 trolled conditions on a specified
indoor laboratory test wheel.

Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from

Sustained high temperature can cause the material of the tires to

degenerate and reduce tires life, and

8 excessive temperature can lead to
sudden tires failure. Grades A and B

steel or other reinforcing materials.
Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim.

represent higher levels of performance on the laboratory test wheel than

Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate

the minimum required by the law.

angles less than 90 degrees to the

centerline of the tread.

7 36

Maintenance

Cold Tire Pressure: The amount of Intended Outboard Sidewall: The Occupant Distribution: Designated

air pressure in a tire, measured in side of an asymmetrical tire, that seating positions.

pounds per square inch (psi) or kilo- must always face outward when Outward Facing Sidewall: The side

pascals (kPa) before a tire has built mounted on a vehicle.

of a asymmetrical tire that has a par- 1

up heat from driving.

Kilopascal (kPa): The metric unit for ticular side that faces outward when

Curb Weight: This means the weight air pressure.

mounted on a vehicle. The outward

of a motor vehicle with standard and Load Index: An assigned number facing sidewall bears white lettering

optional equipment including the ranging from 1 to 279 that corre- or bears manufacturer, brand, and/or

maximum capacity of fuel, oil and sponds to the load carrying capacity model name molding that is higher or

coolant, but without passengers and of a tire.

deeper than the same moldings on

cargo.

Maximum Inflation Pressure: The the inner facing sidewall.

DOT Markings: The DOT code maximum air pressure to which a Passenger (P-Metric) Tire: A tire

includes the Tire Identification cold tire may be inflated. The maxi- used on passenger cars and some

Number (TIN), an alphanumeric des- mum air pressure is molded onto the light duty trucks and multipurpose

ignator which can also identify the sidewall.

vehicles.

tire manufacturer, production plant, brand and date of production.

Maximum Load Rating: The load rating for a tire at the maximum per-

Recommended Inflation Pressure: Vehicle manufacturer's recommend-

GVWR: Gross Vehicle Weight Rating missible inflation pressure for that ed tire inflation pressure and shown

GAWR FRT: Gross Axle Weight tire.

on the tire placard.

Rating for the front Axle.

Maximum Loaded Vehicle Weight: Radial Ply tire: A pneumatic tire in

GAWR RR: Gross Axle Weight The sum of curb weight; accessory which the ply cords that extend to the

Rating for the rear axle.

weight; vehicle capacity weight; and beads are laid at 90 degrees to the

production options weight.

centerline of the tread.

Normal Occupant Weight: The Rim: A metal support for a tire and number of occupants a vehicle is upon which the tire beads are seat-

designed to seat multiplied by 68 kg ed.

(150 pounds).

Sidewall: The portion of a tire

between the tread and the bead.

7 37

Maintenance

Speed Rating: An alphanumeric Vehicle Maximum Load on the All season tires

code assigned to a tire indicating the maximum speed at which a tire can operate.
Traction: The friction between the

Tire: Load on an individual tire due to curb and accessory weight plus maximum occupant and cargo weight.

Kia specifies all season tires on some models to provide good performance for use all year round, including snowy and icy road condi-

tire and the road surface. The Vehicle Normal Load on the Tire: tions. All season tires are identified

amount of grip provided.

That load on an individual tire that is by ALL SEASON and/or M+S (Mud

Tread: The portion of a tire that determined by distributing to each and Snow) on the tire sidewall. Snow

3 4

comes into contact with the road.
Treadwear Indicators: Narrow bands, sometimes called "wear bars," that show across the tread of a

axle its share of the curb weight, accessory weight, and normal occupant weight and driving by 2.
Vehicle Placard: A label permanent-

tires have better snow traction than all season tires and may be more appropriate in some areas.

tire when only 2/32 inch of tread ly attached to a vehicle showing the

remains.

original equipment tire size and rec-

UTQGS: Uniform Tire Quality ommended inflation pressure.

Grading Standards, a tire information system that provides consumers with

ratings for a tire's traction, tempera-

ture and treadwear. Ratings are determined by tire manufacturers

using government testing proce-

8 dures. The ratings are molded into

the sidewall of the tire.

Vehicle Capacity Weight: The number of designated seating positions

multiplied by 68 kg (150 lbs.) plus the

rated cargo and luggage load.

7 38

Summer tires
Kia specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially reduced in snow and ice. Summer tires do not have the tire traction rating M+S (Mud and Snow) on the tire side wall. if you plan to operate your vehicle in snowy or icy conditions. Kia recommends the use of snow tires or all season tires on all four wheels.

Snow tires
If you equip your car with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four wheels; otherwise, poor handling may result.
Snow tires should carry 28 kPa (4 psi) more air pressure than the pressure recommended for the standard tires on the tire label on the driver's side of the center pillar, or up to the maximum pressure shown on the tire sidewall, whichever is less.
Do not drive faster than 120 km/h (75 mph) when your car is equipped with snow tires.

Maintenance
1 2 3 4 5 6 7 8 9
7 39

Maintenance

EXTERIOR CARE

Exterior general caution

Insects, tar, tree sap, bird droppings,

It is very important to follow the label directions when using any chemical cleaner or polish. Read all warning

industrial pollution and similar deposits can damage your vehicle's finish if not removed immediately.

and caution statements that appear Even prompt washing with plain

2 on the label.

water may not completely remove all these deposits. A mild soap, safe for

3 Finish maintenance
Washing

use on painted surfaces, may be used.
After washing, rinse the vehicle thor-

To help protect your vehicle's finish oughly with lukewarm or cold water. from rust and deterioration, wash it Do not allow soap to dry on the fin-

OJB037800

thoroughly and frequently at least ish.

5 once a month with lukewarm or cold

CAUTION

water.

NOTICE

· Water washing in the engine

6 7

If you use your vehicle for off-road driving, you should wash it after each off-road trip. Pay special attention to the removal of any accumulation of salt, dirt, mud, and other foreign

Do not use strong soap, chemical detergents or hot water, and do not wash the vehicle in direct sunlight or when the body of the vehicle is warm.

compartment including high pressure water washing may cause the failure of electrical circuits located in the engine compartment.

materials. Make sure the drain holes

· Never allow water or other liq-

8 in the lower edges of the doors and

uids to come in contact with

rocker panels are kept clear and

electrical/electronic compo-

9 clean.

nents inside the vehicle as this may damage them and

cause a short which can lead

to a fire.

7 40

Maintenance

Waxing
Wax the vehicle when water will no longer bead on the paint.
Always wash and dry the vehicle before waxing. Use a good quality

CAUTION
· Wiping dust or dirt off the body with a dry cloth will scratch the finish.

Finish damage repair
Deep scratches or stone chips in the painted surface must be repaired promptly. Exposed metal will quickly rust and may develop into a major

liquid or paste wax, and follow the manufacturer's instructions. Wax all

· Do not use steel wool, abrasive cleaners, or strong deter-

repair expense.

metal trim to protect it and to maintain its luster.
Removing oil, tar, and similar materials with a spot remover will usually strip the wax from the finish. Be sure to re-wax these areas even if the rest of the vehicle does not yet need waxing.

gents containing highly alkaline or caustic agents on chrome-plated or anodized

NOTICE
If your vehicle is damaged and

aluminum parts. This may requires any metal repair or

result in damage to the pro- replacement, be sure the body shop 4

tective coating and cause dis- applies anti-corrosion materials to

coloration or paint deteriora- the parts repaired or replaced. tion.

7 41

Maintenance

Bright-metal maintenance

Underbody maintenance

· To remove road tar and insects, Corrosive materials used for ice and

WARNING

use a tar remover, not a scraper or snow removal and dust control may

other sharp object.

collect on the underbody. If these

After washing the vehicle, test the brakes while driving slowly

2 3

· To protect the surfaces of brightmetal parts from corrosion, apply a coating of wax or chrome preservative and rub to a high luster.
· During winter weather or in coastal areas, cover the bright metal parts

materials are not removed, accelerated rusting can occur on underbody parts such as the fuel lines, frame, floor pan and exhaust system, even though they have been treated with rust protection.

to see if they have been affected by water. If braking performance is impaired, dry the brakes by applying them lightly while maintaining a slow forward speed.

with a heavier coating of wax or Thoroughly flush the vehicle underpreservative. If necessary, coat the body and wheel openings with luke-

parts with non-corrosive petroleum warm or cold water once a month,

jelly or other protective compound. after off-road driving and at the end of each winter. Pay special attention

to these areas because it is difficult

to see all the mud and dirt. It will do

more harm than good to wet down

the road grime without removing it. The lower edges of doors, rocker

panels, and frame members have

drain holes that should not be allowed to clog with dirt; trapped

water in these areas can cause rust-

ing.

7 42

Aluminum wheel maintenance
The aluminum wheels are coated with a clear protective finish.
· Do not use any abrasive cleaner, polishing compound, solvent, or wire brushes on aluminum wheels. They may scratch or damage the finish.
· Use only a mild soap or neutral detergent, and rinse thoroughly with water. Also, be sure to clean the wheels after driving on salted roads. This helps prevent corrosion.
· Avoid washing the wheels with high-speed car wash brushes.
· Do not use any acid detergent. It may damage and corrode the aluminum wheels coated with a clear protective finish.

Maintenance
1 2 3 4 5 6 7 8 9
7 43

Maintenance

INTERIOR CARE

Interior general precautions

Fabric

Cleaning the lap/shoulder belt

Prevent caustic solutions such as Remove dust and loose dirt from fab- webbing

perfume and cosmetic oil from con- ric with a whisk broom or vacuum Clean the belt webbing with any mild tacting the dashboard because they cleaner. Clean with a mild soap solu- soap solution recommended for

may cause damage or discoloration. tion recommended for upholstery or cleaning upholstery or carpet. Follow

If they do contact the dashboard, carpets. Remove fresh spots imme- the instructions provided with the wipe them off immediately. See the diately with a fabric spot cleaner. If soap. Do not bleach or re-dye the

instructions that follow for the proper fresh spots do not receive immediate webbing because this may weaken

3 way to clean vinyl.

attention, the fabric can be stained it. and its color can be affected. Also, its

Cleaning the upholstery and interior trim

fire-resistant properties can be

reduced if the material is not proper- Cleaning the interior window

ly maintained.

glass

5 Vinyl
Remove dust and loose dirt from

CAUTION

If the interior glass surfaces of the vehicle become fogged (that is, cov-

vinyl with a whisk broom or vacuum Using anything but recommend- ered with an oily, greasy or waxy

6 cleaner. Clean vinyl surfaces with a ed cleaners and procedures film), they should be cleaned with

vinyl cleaner.

may affect the fabric's appear- glass cleaner. Follow the directions

ance and fire-resistant proper- on the glass cleaner container. ties.

CAUTION

Do not scrape or scratch the

inside of the rear window. This

may result in damage to the rear window defroster grid.

7 44

Specifications / 8-2

Specifications

SPECIFICATIONS

The specifications given here are for general information only. Although this information was accurate at the time of

printing, Kia reserves the right to change its vehicles or their specifications without notice. Please check with an

authorized Kia dealer for more precise and more up-to-date information.

1
Dimensions

Item

4 Door

mm (in) 5 Door

Overall length
3 Overall width

4,500 (177.2)/4,510 (177,5) 1,735 (68.3)

4,350 (171.3) 1,735 (68.3)

Overall height
4 Front tread

1,470 (57.9) 1,495 (58.9)

Rear tread
5 Wheelbase

1,485 (58.5) 2,610 (102.8)

6 Tires

Item Tire

8 P195/60R15

9 P205/50R16
Compact spare tire
T125/70D15

Wheel 6.0J x 15 6.0J x 16

Inflation Pressure kPa (psi) 210 (30)
210 (30)

Wheel lug nut torque kg·m (lb·ft, N·m) 9~11 (65~79, 88~107) 9~11 (65~79, 88~107)

420 (60)

9~11 (65~79, 88~107)

Light bulbs
Light Bulb Headlights (Low/High) Front turn signal lights Position lights Front fog lights* Stop and tail lights Rear turn signal lights Back-up lights Rear side mark light High mounted stop light* License plate lights Front map lamp Center dome lamp Door courtesy lamps Trunk room lamp Glove box lamp
* : if equipped

Wattage 55/60 27 5 27 27/8 27 17 5
27 or LED 5 10 10 5 5 5

Specifications
1 2 3 4 5 6 7 8 9
83

Specifications

RECOMMENDED LUBRICANTS AND CAPACITIES
To help achieve proper engine and powertrain performance and durability, use only lubricants of the proper quality. The correct lubricants also help promote engine efficiency that results in improved fuel economy.

1 These lubricants and fluids are recommended for use in your vehicle.

Lubricant

Volume

Classification

Engine oil *1 *2

(drain and refill)

4.0 l (4.23 US qt.)

API Service SJ, SL or above, ILSAC GF-3 or above

Manual transaxle fluid

Automatic transaxle fluid

2.0 l (2.11 US qt.) 6.6 l (6.97 US qt.)

API Service GL-4 (SAE 75W-85, fill for-life) DIAMOND ATF SP-III

Power steering fluid

Coolant
5

Brake/Clutch fluid
6
Fuel

0.8 l (0.85 US qt.)
6.6 l (6.97 US qt.)
0.7~0.8 l (0.7~0.8 US qt.) 53 l (14 US gal.)

PSF-III MIXTURE, Antifreeze with water (Ethylene glycol base coolant for aluminum radiator)
FMVSS116 DOT-3 or DOT-4
-

*1 Refer to the recommended SAE viscosity numbers on the next page.

*2 Engine oils labeled Energy Conserving Oil are now available. Along with other additional benefits, they contribute to fuel economy by reducing the amount of fuel nec-

essary to overcome engine friction. Often, these improvements are difficult to measure in everyday driving, but in a year's time, they can offer significant cost and energy savings.

Specifications

Recommended SAE viscosity Engine oil viscosity (thickness) has an effect on fuel economy and cold

number

weather operating (starting and oil flow). Lower viscosity engine oils can pro-

vide better fuel economy and cold weather performance, however, higher vis-

NOTICE

cosity engine oils are required for satisfactory lubrication in hot weather. 1
Using oils of any viscosity other than those recommended could result in

Always be sure to clean the area around any filler plug, drain plug, or dipstick before checking or draining any lubricant. This is especially important in dusty or sandy areas

engine damage.
When choosing an oil, consider the range of temperature your vehicle will be operated in before the next oil change. Proceed to select the recommended oil viscosity from the chart.

2 3

and when the vehicle is used on

Temperature Range for SAE Viscosity Numbers

unpaved roads. Cleaning the plug and dipstick areas will prevent dirt and grit from entering the engine

Temperature

°C -30 -20 -10 0 10 20 30 40 (°F) -10 0 20 40 60 80 100

50 120

and other mechanisms that could be damaged.

Engine Oil *1

10W-30

5W-20, 5W-30

6
1. For better fuel economy, it is recommended to use the engine oil of a viscosity grade SAE 5W-

20,5W-30 (API SJ, SL / ILSAC GF-3). However, if the engine oil is not available in your coun-

try, select the proper engine oil using the engine oil viscosity chart.

Index

Air bag - Advanced supplemental restraint system..3-50

Air cleaner....................................................................7-21

Antenna ........................................................................3-98 Audio system................................................................3-99

Automatic transaxle.............................................4-6, 7-18
2B

Battery ..........................................................................7-25

Before driving ................................................................5-5

4 Brake system ................................................................4-11
Brakes and clutch........................................................7-15

Climate control air filter.............................................7-22 Cruise control ..............................................................4-21

Defroster.......................................................................4-45 Door locks ......................................................................3-8

9E
Electrical circuit protection........................................6-12 Emergency starting .......................................................6-9 Emission control system ...............................................5-3 Engine compartment ...........................................2-4, 7-10

Engine cooling system.................................................7-12 Engine oil and oil filter ...............................................7-11 Exterior care ................................................................7-40
F
Fuel filler lid ................................................................3-80 Fuel requirements .........................................................5-2
G
Gauges ..........................................................................4-29
H
Hazard warning flasher..............................................4-46 Hood..............................................................................3-78 How to use this manual ................................................1-2
I
If you have a flat tire...................................................6-24 Ignition switch ...............................................................4-2 Immobilizer system .......................................................3-6 Instrument cluster.......................................................4-28 Instrument panel overview...........................................2-3 Interior care .................................................................7-44 Interior features...........................................................3-90 Interior lights ...............................................................3-87 Interior overview ...........................................................2-2

K
Keys ................................................................................3-2
L
Label information........................................................5-25 Lighting ........................................................................4-39 Lubricants and fluids..................................................7-20 Luggage net..................................................................3-97
M
Maintenance schedule...................................................7-3 Maintenance services ....................................................7-2 Manual climate control system ..................................4-47 Manual transaxle .................................................4-5, 7-18 Mirrors .........................................................................3-83
O
Overheating....................................................................6-8 Owner maintenance ......................................................7-7
P
Parking brake ..............................................................7-16 Power steering .............................................................7-17

Index

Remote keyless entry ....................................................3-3

Road warning ................................................................6-2

Safety belts ...................................................................3-27

Seat................................................................................3-16

Special driving conditions ............................................5-7 Specifications .................................................................8-2

Starting the engine ........................................................4-4

Steering wheel ..............................................................4-18

Storage compartment..................................................3-88

Suggestions for economical operation .........................5-6 Sunroof .........................................................................3-94

Theft-alarm system .....................................................4-58

Tires and wheels ..........................................................7-28

Tires pressure monitoring system (TPMS).................6-3

Towing ..........................................................................6-19 Traction control system ..............................................4-25

Trailer towing ..............................................................5-17

Trunk ............................................................................3-76

Vehicle break-in process ...............................................1-3 Vehicle load limit .........................................................5-11

Index

Warnings and indicators ............................................4-31

Weight of the vehicle...................................................5-16

Windows .......................................................................3-13 Windshield defrosting and defogging........................4-56

Wiper blades ................................................................7-23
2 Wipers and washers ....................................................4-43

PScript5.dll Version 5.2 Adobe Acrobat 6.0