Hikvision DS-PDMC-EG2-WB Wireless Magnet Detector

1. Appearance

The detector consists of the following components:

• 1. Magnetic Stick
• 2. Positioning line (on detector)
• 3. Indicator LED
• 4. Tamper Button
• 5. Power Switch
• 6. External Inputs
• 7. Battery (CR123A)

Visual representation: The main unit is a rectangular device. The magnetic stick is a smaller, elongated component. The diagram shows these components and their numbered parts.

2. Enrollment

Refer to the user manual for detailed enrollment procedures.

3. Test

Verify that the installation position is appropriate for optimal performance.

Magnet Detection Performance Table

This table outlines the detection gap performance based on the orientation and movement of the magnetic stick relative to the detector.

Signal Strength Test: The device indicates signal strength. A low voltage level is noted as 2.45 V.

Installation Check: The diagram shows a test sequence with green checkmarks (✔️) and red crosses (❌) indicating successful and failed detection scenarios during alignment.

4. Installation

Follow these steps for installation:

1. Check Signal Strength and Alignment: Ensure good signal strength and align the positioning line on the detector with the magnetic stick.
2. Install the Detector:
   • a. Mounting with screws.
   • b. Mounting with sponge tape (note: this method may not be EN compliant).
3. External Inputs (Optional): If external inputs are required, route the cable through the designated cable hole.

The device may have an indicator light that stays on for approximately 3 minutes during the installation or setup process.

Visual representation: Diagrams show the detector being mounted to a door/frame, with options for screws or tape. Another diagram shows the alignment process with checkmarks (✔️) for correct placement and crosses (❌) for incorrect placement.

User Manual

Scan the QR code for more information and operation help: [QR Code for User Manual]

Specifications

About this Manual and Disclaimer

This manual provides instructions for using and managing the product. Information is subject to change without notice. The latest version is available on the Hikvision website (https://www.hikvision.com/). Use with professional guidance.

Disclaimer: The product is provided "as is". Hikvision disclaims warranties for merchantability, quality, or fitness for a particular purpose. Hikvision is not liable for indirect damages, business losses, or data loss. Users acknowledge internet security risks and are responsible for legal compliance and respecting third-party rights. Prohibited uses include weapons development. In case of conflict with law, the law prevails.

Safety and Compliance Information

Product Markings: The product is marked with "CE", complying with European standards (RE Directive 2014/53/EU, EMC Directive 2014/30/EU, RoHS Directive 2011/65/EU).

WEEE Directive (2012/19/EU): Products marked with this symbol ♻️ cannot be disposed of as unsorted municipal waste in the EU. Return to supplier or designated collection points for recycling.

Battery Directive (2006/66/EC): The product contains a battery ? that must be recycled properly. Do not dispose of as unsorted waste. Return to supplier or designated collection points.

Warnings and Cautions

Battery Warnings:

• ⚠️ Do not ingest battery; Chemical Burn Hazard.
• Keep new and used batteries away from children.
• If the battery compartment does not close securely, stop using the product and keep it away from children.
• Seek immediate medical attention if batteries are swallowed or placed inside any part of the body.

Battery Cautions:

• Risk of fire or explosion if the battery is replaced with an incorrect type.
• Improper battery replacement may defeat safeguards.
• Do not dispose of batteries in fire or hot ovens, or crush/cut them.
• Do not expose batteries to extremely high temperatures or low air pressure, which may cause explosion or leakage.
• Dispose of used batteries according to instructions.

Installation Cautions:

Additional force equal to three times the equipment weight (minimum 50N) must be applied to ensure the equipment and mounting remain secure. The equipment and mounting plate should not be damaged after installation.

FCC Information

This is a Class B product. In a domestic environment, it may cause radio interference, requiring user action.

FCC Compliance: This equipment has been tested and found to comply with Class B digital device limits under Part 15 of FCC Rules. These limits provide reasonable protection against harmful interference in residential installations. If interference occurs, users are encouraged to:

• Reorient or relocate the receiving antenna.
• Increase separation between equipment and receiver.
• Connect equipment to a different circuit than the receiver.
• Consult the dealer or an experienced radio/TV technician.

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: 1. The device must not cause harmful interference. 2. The device must accept any received interference, including that which may cause undesired operation.