Philips EasyKey 6000 Series DDL609 Smart Door Lock

Safety Precautions

• Read the user manual before use. Failure to follow instructions may void the warranty.
• Use only specified parts and accessories.
• Use only alkaline batteries of the same type.
• Do not disassemble the product.
• Avoid using sharp objects on the fingerprint sensor.
• Keep the product away from rain and moisture.
• Avoid contact with corrosive substances.
• Do not hang items on the door handle.
• Clean with a soft cloth.
• Do not remove the battery ? while performing setup operations.
• Installation should be performed by a qualified professional following the manual.
• Change the master PIN after installation.
• Replace low batteries ? promptly, ensuring correct polarity.

Warnings

• Keep batteries ? away from heat sources ? to prevent fire hazards.
• Do not use incompatible power sources.
• Avoid short-circuiting battery terminals.
• Service should only be performed by authorized personnel.
• Using non-Philips or unauthorized accessories may void the warranty.

Disposal of Old Products and Batteries

• Recycle old smart locks at authorized Philips service centers.
• Follow local regulations for waste disposal ♻️.
• Do not mix electronic waste with household waste.
• Dispose of old products properly to protect the environment and public health.
• Batteries and battery waste should not be mixed with household waste.
• Follow proper battery collection and sorting procedures.

Parts List

[Image: A visual inventory of all included parts for the smart lock.]

• 1. Front Lock with Silicone Gasket
• 2. Rear Lock with Silicone Gasket
• 3. Hole Cutting Template ?
• 4. Bolt
• 5. User Manual ?
• 6. Warranty Card ?
• 7. Mechanical Key ?
• 8. Batteries ?
• 9. Screwdriver Kit ?️
• 10. Strike Plate
• 11. RFID Card ?
• 12. Cylinder

3D Assembly Diagram

[Image: An exploded view diagram illustrating the assembly process of the smart lock components, with numbered parts corresponding to the parts list.]

Key components in the diagram:

• 1. Rear Cover*1
• 2. AA Batteries*4
• 3. Screws for internal lock hole*2
• 4. Rear Lock*1
• 5. Bolt*1
• 6. Bolt fixing screws*2
• 7. M6 Spindle*2
• 8. Set Screw*1
• 9. Bolt Retainer*1
• 10. Front Lock*1
• 11. Cylinder*1
• 12. Screws for mechanical cylinder*1

Before Installation

Installation Steps

Instructions are provided for Right Push doors, with notes to refer to "Before Installation" for Left Push doors.

1. Drill holes on the door using the provided template. Install the bolt and secure it with screws.
2. On the front lock, install the spindle and spring, then insert the spindle into the handle.
3. Install screws and the spindle onto the front lock body.
4. Route the cable through the door hole. Align the front lock's square spindle with the bolt mechanism, and attach it to the door, ensuring a flush fit.
5. Install the mounting plate on the inside of the door and secure it with M6 screws.
6. Install AA batteries ? and attach the rear cover. Check that all rotating parts, the mechanical key ?, and other components are securely fastened and operate smoothly.

Note: After installing the strike plate, check that the lock bolts extend and retract smoothly.

Front Lock

[Image: A diagram of the front of the smart lock with numbered callouts.]

• 1. Indicator Light
• 2. Keypad
• 3. RFID Card ? Reader Area
• 4. Mute Button ?
• 5. Fingerprint ?️ Sensor
• 6. Handle
• 7. Mechanical Keyhole ?
• 8. Emergency Power Port ?

Rear Lock

[Image: A diagram of the rear of the smart lock with numbered callouts.]

• 1. Battery Compartment ?
• 2. Handle
• 3. Reset (RES) Button ↩️

Before Setup

The smart lock system supports two modes: Normal Mode and Dual-Authentication Mode.

• Normal Mode: Unlock using any registered method (PIN, Card ?, Fingerprint ?️).
• Dual-Authentication Mode: Requires two methods to be used in combination for unlocking (e.g., PIN + Card ?, PIN + Fingerprint ?️, Card ? + Fingerprint ?️).

Note: Fingerprint ?️ unlocking is optional.

Setup Notes:

• The DDL609 supports two external unlocking methods: "Fingerprint ?️ + PIN + Card ? + Mechanical Key ?" or "PIN + Card ? + Mechanical Key ?".
• Fingerprint ?️ unlocking is optional.
• In Dual-Authentication Mode, the combination methods may vary.

Icon Meanings:

• [??] Master PIN (for management)
• [??] User PIN (for members)
• [?️] Fingerprint
• [*] Key
• [#] Key
• [?] RFID Card

Default Master PIN: 12345678.

Changing Initial Master PIN

Enter Master Mode, then press [1] to change the Master PIN. The indicator will flash green ? once. Enter the new Master PIN (6-12 digits) and confirm with [#]. The system will beep and flash green ? once. Re-enter the new Master PIN and confirm with [#]. A successful setup will result in a beep and the indicator flashing green ?? twice.

Changing Master PIN

Enter Master Mode, then press [1] to change the Master PIN. The indicator will flash green ? once. Enter the new Master PIN (6-12 digits) and confirm with [#]. The system will beep and flash green ? once. Re-enter the new Master PIN and confirm with [#]. A successful setup will result in a beep and the indicator flashing green ?? twice.

Adding User PIN

Enter Master Mode, then press [2] to add a User PIN. The indicator will flash green ? once. Enter the new User PIN (6-12 digits) and confirm with [#]. The system will beep and flash green ? once. Re-enter the User PIN and confirm with [#]. A successful setup will result in a beep and the indicator flashing green ?? twice.

Deleting User PIN

Enter Master Mode, then press [3] to delete a User PIN. The indicator will flash green ? once. Enter the PIN to be deleted and confirm with [#]. A successful deletion will result in a beep and the indicator flashing green ?? twice.

Adding User Fingerprint (Optional)

Enter Master Mode, then press [5] to add a fingerprint ?️. The indicator will flash green ? once. Place your finger on the sensor until you hear a beep, then lift and repeat 8 times. A successful addition will result in a beep and the indicator flashing green ?? twice.

Note: Fingerprint ?️ function is optional.

Deleting User Fingerprint (Optional)

Enter Master Mode, then press [6] to delete a fingerprint ?️. The indicator will flash green ? once. Place your finger on the sensor until you hear a voice prompt, then lift. The indicator flashing green ?? twice confirms deletion.

Adding RFID Card

Enter Master Mode, then press [7] to add an RFID card ?. The indicator will flash green ? once. Place the card on the reader until you hear a beep. A successful addition will result in a beep and the indicator flashing green ?? twice.

Deleting RFID Card

Enter Master Mode, then press [8] to delete an RFID card ?. The indicator will flash green ? once. Place the card on the reader until you hear a voice prompt. A successful deletion will result in a beep and the indicator flashing green ?? twice.

Passage Mode Setup

Press [9] to set up Passage Mode. The indicator will flash green ? once.

• Press [1] to enable Passage Mode (allows anyone to open the door).
• Press [2] to disable Passage Mode (only registered methods can open the door).

A successful setup will result in a beep and the indicator flashing green ?? twice.

Note: To disable Passage Mode, press and hold [8] for 3 seconds. The mode will re-enable automatically when the next user unlocks the door.

Verification Mode Setup

Press [0] to set up Verification Mode. The indicator will flash green ? once.

• Press [1] for Single Authentication Mode (unlock with PIN, Card ?, or Fingerprint ?️).
• Press [2] for Dual-Authentication Mode (unlock with any two methods: PIN, Card ?, Fingerprint ?️).

A successful setup will result in a beep and the indicator flashing green ?? twice.

Note: If your model does not have fingerprint ?️ functionality, Dual-Authentication Mode will use PIN and Card ?.

Unlocking from Outside

Unlocking from Inside

Push the handle down to unlock the door.

[Image: Hand pushing down the interior door handle.]

Locking the Door

After closing the door, lift the handle upwards. The bolt will automatically extend to lock the door.

[Image: Hand lifting the interior door handle to lock.]

Unlocking with Mechanical Key

1. Take out the mechanical key ?.
2. Open the cover below the exterior lock mechanism and rotate 90° ? to reveal the keyhole.
3. Insert the key ?. The key and exterior lock should be at a 90° angle. Turn the key left or right about 1.5 turns to unlock.

Note: It is not recommended to use the mechanical key ? for daily unlocking. Use it only when the battery is depleted, the PIN is forgotten, or the system malfunctions.

Factory Reset

Purpose: To erase all user data and restore the lock to its factory default settings.

How to Use: Use a pointed object to double-press the [RES] button ↩️ to perform a factory reset. All user information will be erased and restored to the manufacturer's default settings.

[Image: Close-up of the reset button labeled 'RES' on the interior lock mechanism.]

Mute Function

Purpose: Enables silent operation by disabling voice prompts, useful for not disturbing others.

How to Use:

1. To activate Mute Mode: Wake the screen, then press and hold the [Mute/Speaker] button ? for 2 seconds. The system will announce "Mute mode activated" and the indicator will turn white ⚪.
2. To deactivate Mute Mode: Wake the screen, then press and hold the [Mute/Speaker] button ? for 2 seconds. The system will announce "Voice prompt activated" and the indicator will turn white ⚪.

Lock Status Indicator

• Blue ?: System is waking up.
• Green ?: Door unlocked successfully.
• Red ?: Door locked successfully.

[Image: Diagram showing the indicator light on the lock.]

Mute Indicator

White ⚪: Mute mode is active or inactive; the indicator is always white.

[Image: Diagram showing the mute button.]

Anti-Peep Indicator

• Flashing 2 times (2 minutes):
• Flashing 1 time (1 minute):

The system will lock for 100 seconds after 5 failed unlock attempts within 5 minutes.

Note: The system lockout notification appears only after waking the keypad or attempting an unlock.

Note: Fingerprint ?️ unlocking is optional.

Low Battery Warning

Trigger: The battery voltage is detected upon system wake-up. A warning is issued when the battery is low. Replace the battery ? promptly.

A voice prompt will announce the low battery status when the door is opened. The warning automatically turns off.

External Power Charging

If the battery is depleted and the door cannot be opened from the outside, use a 5V power bank connected to the emergency power port ? on the lock. After opening the door, replace the batteries ? immediately or charge them. Avoid letting the battery completely deplete to preserve its lifespan.

[Image: A hand connecting a power bank to the emergency power port at the bottom of the lock.]

Replacing Batteries

The battery compartment ? is located on the upper part of the rear lock. Remove the rear cover to replace the batteries.

[Image: Diagram showing the rear lock cover being removed to access the battery compartment.]