Pulsar 510 DL 2.0 PRO Auto-Draw Variable Voltage Vape Bar

Specifications

Kit Includes

• 1 x Pulsar 510 DL 2.0 PRO Battery
• 1 x Bottom Magnetic Connector

Power On/Off

The device enters a standby mode after 10 seconds of inactivity. To wake the device, press the button on the bottom once. The screen will turn on, and the LED will flash the current voltage. Alternatively, you can pull from the mouthpiece to activate the device. The screen displays the battery life in percentage.

Pre-heating

To activate the pre-heat function, quickly pull from the mouthpiece twice, or press the button on the bottom two times.

Change Voltage Setting

Cycle through voltage settings by pressing the button on the bottom once. The screen indicates the selected voltage with colored bars:

• 2.4V - Yellow
• 2.6V - Purple
• 2.8V - Green
• 3.4V - Blue
• 3.8V - Red

Charging

Charging Indicator: Red light and a lightning icon flash on the screen.
Fully Charged Indicator: Green light.

Low Battery Warning: The red light will flash 10 times to alert the user. The device will then enter standby mode. Charge the device before continuing use.

Protection Features

• Battery life/cartridge protection: After 10 continuous seconds of use, the red light flashes 4 times, and the automatic vape time cutoff activates, stopping the heat but not the power.
• Over-voltage/short-circuit protection: The red light flashes 3 times, and the device will fully turn off.

Quick Start Instructions

1. Connect your device to a power source and charge until the light turns green.
2. Insert the 510-threaded cartridge of your choice.
3. Press the button on the bottom of the device 1 time to wake it up.
4. Press the button on the bottom 1 time to change the voltage; repeat until you are at your desired setting.
5. Quickly pull twice to start pre-heating or press the power button 2 times.
6. Pull from the mouthpiece and enjoy.

Instructions

1. Ensure the bottom magnetic connector is properly attached to the bottom of the unit. The battery will not charge if the connector is not attached.
2. Plug in and connect to a power source. A single light flash indicates the battery is connected.
3. Allow the battery to fully charge before first use. The charging light will turn green. Disconnect the device from the power source before use.
4. Remove the bottom magnetic connector and screw the 510-threaded cartridge of your choice firmly into it.
5. Insert the cartridge into the device, ensuring the bottom magnetic connector is properly reconnected. You should feel haptic feedback confirming a good connection.
6. Press the power button 1 time to adjust the voltage.
7. Activate the pre-heat function to prime the cartridge by giving the unit 2 quick pulls or pressing the power button 2 times. This activates the unit at 1.8V for 15 seconds. After 15 seconds, the unit will revert to your previously selected voltage.
8. Pull from the mouthpiece to activate the cartridge vapor and enjoy your session.
9. To reset the puff counter, press the button 3 times quickly. On the third press, hold the button down until the puff counter resets.

Cleaning Instructions

1. Remove the bottom magnetic connector from the battery.
2. Wipe the outside and inside of the bottom magnetic connector with an isopropyl alcohol pad. Use an alcohol swab to remove any excess oil from the 510 screw-in connector.
3. Clean the inside air pathway with an alcohol swab. Use a circular motion to clean the air pathway until no more oil is visible.
4. Do not submerge any part of the device in cleaning solution. Allow all parts to air dry before resuming use. [!]

Note: The mouthpiece is not removable. Attempting to remove it could impair or permanently disable the breath control functionality.

Important Safety Warnings

• Do not expose to extreme temperatures or direct sunlight.
• Do not drop the device or accessories.
• Do not drop or submerge in any liquid.
• Do not modify the electronics in any way.
• This device is intended for adults only. Do not sell or provide to minors.
• Keep all parts, concentrates, herbs, and liquids away from children and pets.
• This is not a medical device and is not intended to diagnose, treat, mitigate, cure, or prevent any ailment, disease, or other conditions.
• Consult a physician before use, especially if you suffer from heart disease or any other medical condition, or if you are pregnant or breastfeeding.
• Failure to follow any of these instructions could result in product damage, property damage, personal injury, and may void warranty.

For the most current version of the manual, scan the QR code on packaging or visit: https://www.pulsarshop.com/pages/manuals