Antari SW-250/SW-250X Snow Machine

Introduction

Thank you for choosing the Antari SW-250/SW-250X Snow Machine. Prior to use, it is suggested to read the instructions carefully and thoroughly. By following the instructions listed in this user manual, you can look forward to the best haze effect and the most reliable performance of your Antari SW-250/SW-250X Snow Machine for years to come.

⚠️ Please follow these operation and safety instructions to ensure a long and safe life for your SW-250/SW-250X.

Safety Warnings

DANGER OF ELECTRIC SHOCK

• Keep this device dry.
• For indoor use only. Not designed for outside use.
• Use a grounded electrical outlet. Ensure the unit is installed at the rated voltage.
• Always unplug the machine before filling snow fluid.
• Turn off or unplug when not in use.
• This machine is not water or splash proof. If moisture, water, or snow fluid gets inside the housing, immediately unplug the unit. After unplugging, wipe the unit with a dry cloth and leave it to stand still for a while. If any problem occurs upon reuse, contact a service technician or your ANTARI dealer.

DANGER OF BURN

• No user-serviceable parts inside. Do not disassemble the housing or make any modifications; otherwise, damage to the device or danger of burn may be caused.
• For adult use only. The machine must be installed out of the reach of children. Never leave the unit running unattended.
• Position the machine in a well-ventilated area. Leave at least 20cm (approx. 8 inches) of space surrounding the machine.
• Never add flammable liquids of any kind (oil, gas, perfume) to the snow fluid.
• Use only dealer-recommended genuine Antari snow fluid SL-5(A). Do not use any other liquid which may cause erosion of inner parts.
• If your Antari SW-250/SW-250X Snow Machine fails to work properly, stop using it immediately. Contact your Antari dealer first. Pack the unit securely (preferably with the original packing material) and return it to your ANTARI dealer for service.

⚠️ Pay attention to all warning labels, signs, and instructions printed on the exterior of your Antari Snow Machine.

Unpacking & Inspection

Open the shipping carton and check that all equipment necessary to operate the machine have arrived intact.

The shipping carton should contain the following items:

• Snow machine with power cable
• W-1 wireless transmitter (Only for SW-250 model)
• Fluid tank
• Hanging bracket
• Screw set and user manual

Before beginning initial setup, ensure there is no evident damage caused by transportation. In the event of a damaged cable or unit housing, do not plug it in nor use it until contacting your Antari dealer for assistance.

Setup and Power On

1. Remove all packing materials from the shipping box. Ensure all foam and plastic paddings are removed.
2. Place the machine on a flat surface and follow the steps below.

3. Assembling Tank & Filter: A diagram shows the PU liquid tube connecting to a filter, which is then inserted into the tank. An adaptor with a nut must be tightly connected.

4. Assembling Hanging Bracket: A diagram illustrates attaching the hanging bracket to the machine using M8 screws. Four washers are assembled on both inner sides of the hanging bracket, with M8 screws on the outer sides as indicated. Tightening screws are used to adjust the machine's angle when in the air.

5. Fill with ANTARI SL-5(A) snow fluid. Any other types of fluid can damage the unit. When filled, place the cap back on the liquid tank.
6. Plug the power cable into a grounded electrical outlet and flip the power switch at the rear of the machine to power it on.

Transmitter Registration (ONLY FOR SW-250 MODEL)

After powering on, the LCD screen will show sequentially "Antari SW-250" and then "Wireless Setup...". Press button "A" on the transmitter(s) to register when "Wireless Setup..." is visible. There is a total of 15 seconds to finish the registration. Once registration is completed, the LCD screen will blink and beep, finally showing "Wireless Setup OK". Up to 5 transmitters can be registered with one SW-250. The included transmitter is pre-registered and can be operated without start-up setting. Registration is only needed for new W-1 transmitters.

Note: All transmitter(s) registration must be completed within 15 seconds, or the SW-250 must be powered on again for the next registration.

LCD Control Operation

After transmitter registration, the LCD screen will show "Ready To Snow". The machine is now ready for operating.

LCD Display: A visual representation of the LCD screen showing "Ready To Snow" with four circular buttons below labeled TIMER and VOLUME.

Functions Setting

Press the [MENU] button for setting different functions:

• Interval Set: Set the interval time under timer mode by pressing [Up/Timer] and [Down/Volume] buttons (20 to 2000 seconds).
• Duration Set: Set the duration time under timer mode by pressing [Up/Timer] and [Down/Volume] buttons (10 to 200 seconds).
• Timer Out: Set the output volume under timer mode by pressing [Up/Timer] and [Down/Volume] buttons (1% to 100%).
• Volume Out: Set the output volume under continuous mode by pressing [Up/Timer] and [Down/Volume] buttons (1% to 100%).
• DMX512 Add: Set the DMX channel under DMX control mode by pressing [Up/Timer] and [Down/Volume] buttons (1 to 512 channels).
• Wireless ON: Activate/terminate the wireless control system by pressing [Up/Timer] and [Down/Volume] buttons (ON/OFF). When active, the letter "W" is displayed.
• Quick Start: Activate/terminate quick start function by pressing [Up/Timer] and [Down/Volume] buttons (ON/OFF). When active, the machine resumes the last operation mode upon power-on.

Output Modes

• Output Under Timer Mode: Press [Up/Timer] button to execute timing set and press [Stop] to stop.
• Output Under Continuous Output Mode: Press [Down/Volume] button for continuous output until [Stop] button is pressed.

Remote Control Operation (ONLY FOR SW-250 MODEL)

W-1 Wireless Remote Control

The W-1 wireless remote consists of a transmitter with two buttons for output on and off, and a receiver pre-attached to the SW-250.

Transmitter

Transmitter Image: A description of the Antari wireless remote control with two buttons, labeled "A" for output and "B" for stop. The transmitter has an LED indicator.

The transmitter allows output via radio up to 50 meters. It is compatible with any SW-250 receiver and can control an unlimited number of machines in parallel. Press button "A" to output; the LED on the transmitter lights up. Press button "B" to stop output.

Receiver

Receiver Image: A description of the small black receiver unit that attaches to the machine.

The receiver is tested and built into the SW-250. It responds to up to 5 different registered transmitters. The included transmitter is pre-registered and can be operated without any start-up setting.

Battery Change on the Transmitter

If the transmitter's range decreases, the battery is likely exhausted and needs replacement. Remove the housing cover, remove the used battery, insert a fresh 12V battery, and refit the cover.

SC-2 (Optional) Wired Remote

The SC-2 is a 25 ft. wired ON/OFF and volume remote controller with a 4-pin XLR plug.

SC-2 Remote Description:

• Red Switch: ON/OFF for snow output.
• Volume Knob: Adjusts output volume from 10% to 100%.
• Red LED Indicator: Illuminates when the remote is connected to the machine.
• Green LED Indicator: Illuminates when the red switch is turned ON.

DMX Control

DMX Connector Pin Assignment

The machine provides a 5-pin XLR connector for DMX connection. The diagram below indicates pin assignment information.

DMX Connector Diagram: A description of the 5-pin XLR connector pinout, showing Pin 1 (Ground), Pin 2 (Data-), Pin 3 (Data+), Pin 4 (N/A), and Pin 5 (N/A).

DMX Control Operation

The SW-250/SW-250X has on-board DMX control, with addressing via the LCD control panel. It uses 1 channel to control output on/off and volume, with a value range from 0 to 255. The on/off function can also be programmed with a DMX controller or software.

Channel A:

• 0-10 = OFF
• 11-255 = ON (1%-100%)

Note: Once a DMX cable is connected, the LCD control panel, W-1 transmitter, and HC-1 controller cannot be used.

Maintenance

1. Do not allow the snow liquid to become contaminated. Always replace caps on the liquid container and the snow machine liquid tank immediately after filling.
2. Before storing, rinse the system with pure water and let it pump for at least 1-2 minutes. This helps ensure a longer life-span for the motor and nozzle.
3. Regularly clean dust/residue around the machine's vent holes (on both sides) using a small brush (like a toothbrush), brushing gently from top to bottom. This helps prevent debris from entering the machine and causing clogs.

Caution & Attention

⚠️ Never drink snow fluid. If ingested, seek medical attention immediately. If fluid contacts skin or eyes, rinse thoroughly with cold water.

If you experience low output, mechanical noise, or no output after following the operation steps, unplug the unit immediately. Check the fluid level, external fuse, remote control connection, and power cable. If all appear OK, plug it back in. If the machine is still not functional, discontinue operation to prevent permanent damage and return it to your Antari dealer.

Snow Fluid

Antari SL-5/SL-5(A) fluid is designed for Antari snow machines. Antari SL-5(A) is a non-toxic solution that produces fast-dissipating snow.

Technical Specifications

Approval: This product complies with the R&TTE directive (Radio and Telecommunication Technical Equipment) of the European Union and is Class 1 equipment. Operation is generally approved in EU member countries. Approval may be required by national authorities in countries outside the EU.