Oct 11, 2024 — For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF ...
11 ott 2024 — For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF ...
240W Constant Power Mode LED Driver
XLG-240 series
User's Manual
IS 15885
THOMAS SAMUEL
THOMAS SAMUEL
Note.15
Note.19
(Except for 48V) (Except for 48V) (Except for 48V/Blank type)
IP67
05
Note.13
Note.14
:
File Name:XLG-240-SPEC 2024-10-11
240W Constant Power Mode LED Driver
XLG-240 series
SPECIFICATION
MODEL OUTPUT
INPUT
RATED CURRENT (Default) RATED POWER CONSTANT CURRENT REGION Note.2 FULL POWER CURRENT RANGE OPEN CIRCUIT VOLTAGE (max.)
CURRENT ADJ. RANGE
CURRENT RIPPLE
CURRENT TOLERANCE
SET UP TIME
Note.6
VOLTAGE RANGE Note.5
FREQUENCY RANGE
POWER FACTOR (Typ.)
TOTAL HARMONIC DISTORTION
EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT(Typ.) MAX. NO. of PSUs on 16A CIRCUIT BREAKER LEAKAGE CURRENT
XLG-240 -L-
XLG-240 -M-
XLG-240 -H-
700mA
1400mA
4900mA
239.4W 178~ 342V
239.4W 90 ~171V
239.6W 27 ~ 56V
700~1050mA
1400~2100mA
4280~6660mA
370V
186V
60V
Adjustable for A/AB-Type only (via the built-in potentiometer)
350~1050mA
700~2100mA
2400~6660mA
5.0%(@ Load50% rated voltage)
±4%
500ms/230VAC, 1200ms/115VAC
100 ~ 305VAC 142 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" and " DRIVING METHODS OF LED MODULE"section)
47 ~ 63Hz
PF0.97 / 115VAC, PF0.95 / 230VAC, PF0.92 / 277VAC at full load (Please refer to "Power Factor Characteristic" section)
THD< 10% (@ load50% at 115VAC/230VAC ,@load75% at 277VAC) Please refer to "TOTAL HARMONIC DISTORTION (THD)" section
93%
92.5%
91%
2.7A / 115VAC 1.3A / 230VAC 1.1A / 277VAC COLD START 85A(twidth=500s measured at 50% Ipeak) at 230VAC; Per NEMA 410
2 unit(circuit breaker of type B) / 4 units(circuit breaker of type C) at 230VAC
<0.75mA / 277VAC
PROTECTION ENVIRONMENT
STANDBY POWER CONSUMPTION SHORT CIRCUIT
OVER VOLTAGE
INPUT OVER VOLTAGE Note.7 OVER TEMPERATURE WORKING TEMP. MAX. CASE TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION
SAFETY STANDARDS
Standby power consumption <0.5W for AB-Type(Dimming OFF)(for standard version)
Hiccup mode or constant current limiting, recovers automatically after fault condition is removed
380 ~ 450V
190~ 240V
61 ~ 85V
Shut down output voltage, re-power on to recovery
320 ~ 390VAC (Shut down output when the input exceeds protection voltage,recovers automatically after fault condition is removed)
Can survive input voltage stress of 440Vac for 48 hours Shut down output voltage, re-power on to recover
Tcase=-40 ~ +90(Please refer to "OUTPUT LOAD vs TEMPERATURE" section)
Tcase=+90 20 ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH non-condensing ±0.03%/ (0 ~ 60) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
UL8750(type"HL"), CSA C22.2 No. 250.13-12; ENEC BS EN/EN61347-1, BS EN/EN61347-2-13 independent, BS EN/EN62384; GB19510.1, GB19510.14; EAC TP TC 004; J61347-1(H29), J61347-2-13(H29),KC61347-1,KC61347-2-13,IS15885(Part2/Sec13); NOM-058-SCFI-2017(except for Blank type); IP67 approved
SAFETY & EMC (Note 8)
OTHERS NOTE
WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
ISOLATION RESISTANCE
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH
Parameter
Standard
Conducted
BS EN/EN55015(CISPR15),GB/T 17743
Test Level / Note -----
EMC EMISSION
Radiated Harmonic Current
BS EN/EN55015(CISPR15),GB/T 17743 BS EN/EN61000-3-2 , GB17625.1
----Class C @load50%
Voltage Flicker
BS EN/EN61000-3-3
-----
BS EN/EN61547
Parameter
Standard
Test Level / Note
ESD
BS EN/EN61000-4-2
Level 3, 8KV air ; Level 2, 4KV contact
Radiated
BS EN/EN61000-4-3
Level 2
EMC IMMUNITY
EFT / Burst Surge
BS EN/EN61000-4-4 BS EN/EN61000-4-5
Level 3 4KV/Line-Line 6KV/Line-Earth(6K/10K option)
Conducted
BS EN/EN61000-4-6
Level 2
Magnetic Field
BS EN/EN61000-4-8
Level 4
Voltage Dips and Interruptions
BS EN/EN61000-4-11
>95% dip 0.5 periods, 30% dip 25 periods, >95% interruptions 250 periods
MTBF
2496.2K hrs min. Telcordia SR-332(Bellcore) ; 219.8K hrs min. MIL-HDBK-217F (25)
DIMENSION
219*63*35.5mm (L*W*H)
PACKING
1Kg;16pcs / 16Kg / 0.8CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature. 2. Please refer to "DRIVING METHODS OF LED MODULE". 3. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 4. Tolerance : includes set up tolerance, line regulation and load regulation. 5. De-rating may be needed under low input voltages. Please refer to "STATIC CHARACTERISTIC" sections for details.If continually operate with AC on/off
in short time , it may causes PWM driver IC into protection status. 6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time 7. Only for XLG-240 I series,and Iseries without UL/CSA certificate. 8. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 9. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75 or less. 10. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com 11. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently connected to the mains. 12. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft). 13. H type:RCM is on a voluntary basis. Non IC classification Independent LED control gear is not suitable for residential installations.
M,L type:RCM is on a voluntary basis and meets relevant IEC or AS/NZS standards complying with AS/NZS 4417.1. 14. Products sourced from the Americas regions may not have the CCC/PSE/BIS/KC logo. Please contact your MEAN WELL sales for more information. 15. Some products may not have the BIS logo, please contact your MEAN WELL sales for more information. 16. For any application note and IP water proof function installation caution, please refer our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf 17. When the current adjustment is more than 110% of the rated current, it will be enter the Protection state. 18. It may has an over-shoot status at output current when AC On/Off operate with lower Vf and lower loading conditions. 19. If you need the NOM (Mexico) certificate, Please contact MEAN WELL sales representative for details. 20. For A/AB/ABV type need to consider build in using to comply with Type HL application.
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:XLG-240-SPEC 2024-10-11
240W Constant Voltage LED Driver
XLG-240 series
SPECIFICATION
MODEL OUTPUT
RATED CURRENT
RATED POWER(Max.)
DC VOLTAGE
RIPPLE & NOISE(max.)
VOLTAGE TOLERANCE
LINE REGULATION
LOAD REGULATION
DIMMING TOLERANCE
SET UP TIME
Note.9
XLG-240-48-ABV 5A 240W 48V (adjustable 43.2~52.8V) 250mVp-p ±2.0% ±0.5% ±0.5% ±4%
500ms/230VAC, 1200ms/115VAC
VOLTAGE RANGE FREQUENCY RANGE
110 ~ 305VAC 47 ~ 63Hz
156VDC ~ 431VDC
POWER FACTOR (Typ.)
PF0.97 / 115VAC, PF0.95 / 230VAC, PF0.92 / 277VAC at full load
TOTAL HARMONIC DISTORTION THD< 10% @ load50% at 115VAC/230VAC, @Load>75% at 277VAC;
INPUT EFFICIENCY (Typ.)
91%
AC CURRENT (Typ.)
2.7A / 115VAC 1.3A / 230VAC 1.1A / 277VAC
INRUSH CURRENT(Typ.)
COLD START 85A(twidth=500s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. NO. of PSUs on 16A CIRCUIT BREAKER LEAKAGE CURRENT
2 unit(circuit breaker of type B) / 4 units(circuit breaker of type C) at 230VAC <0.75mA / 277VAC
STANDBY POWER CONSUMPTION Standby power consumption <0.5W for ABV/BV-Type(Dimming OFF)(for standard version)
SHORT CIRCUIT
Hiccup mode or Constant current limiting, recovers automatically after fault condition is removed
OVER VOLTAGE PROTECTION OVER TEMPERATURE
OVER LOAD
54 ~ 60V Shut down output voltage, re-power on to recovery
Note.10 Shut down output voltage, re-power on to recover 105~135% Hiccup mode or Constant current limiting, recovers automatically after fault condition is removed
WORKING TEMP. MAX. CASE TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY
Tcase=-20 ~ +90(Please refer to "OUTPUT LOAD vs TEMPERATURE" section) Tcase=+90 20 ~ 95% RH non-condensing -20 ~ +80, 10 ~ 95% RH non-condensing
TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE
EMC EMISSION
SAFETY & EMC
EMC IMMUNITY
±0.03%/ (0 ~ 60)
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
UL8750(type"HL"), CSA C22.2 No. 250.13-12; ENEC BS EN/EN61347-1, BS EN/EN61347-2-13 independent, BS EN/EN62384; IS15885(Part2/Sec13)(Note 14), GB19510.1, GB19510.14;EAC TP TC 004; IP67 approved
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH
Parameter Conducted
Standard BS EN/EN55015(CISPR15),GB/T 17743
Test Level / Note -----
Radiated
BS EN/EN55015(CISPR15),GB/T 17743
-----
Harmonic Current
BS EN/EN61000-3-2 ,GB17625.1
Class C @load50%
Voltage Flicker
BS EN/EN61000-3-3
-----
BS EN/EN61547 Parameter ESD
Standard BS EN/EN61000-4-2
Test Level / Note Level 3, 8KV air ; Level 2, 4KV contact
Radiated EFT / Burst Surge
BS EN/EN61000-4-3 BS EN/EN61000-4-4 BS EN/EN61000-4-5
Level 2 Level 3 4KV/Line-Line 6KV/Line-Earth
Conducted Magnetic Field
BS EN/EN61000-4-6 BS EN/EN61000-4-8
Level 2 Level 4
Voltage Dips and Interruptions
BS EN/EN61000-4-11
>95% dip 0.5 periods, 30% dip 25 periods, >95% interruptions 250 periods
OTHERS NOTE
MTBF
2496.2K hrs min. Telcordia SR-332(Bellcore) ; 219.8K hrs min. MIL-HDBK-217F (25)
DIMENSION
219*63*35.5mm (L*W*H)
PACKING
1Kg;16pcs / 16Kg / 0.8CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature. 2. De-rating may be needed under low input voltages. Please refer to "STATIC CHARACTERISTIC" sections for details. 3. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation,
the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 4. This series meets the typical life expectancy >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is 70 or less. 5. To fulfill requirements of the latest ErP regulation for lighting fixture, this LED 6. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com 7. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft). 8. For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf 9. Products sourced from the Americas regions may not have the ENEC/CCC/KC logo. Please contact your MEAN WELL sales for more information. 10.When the secondary OTP fails, there is also a primary OTP, which is protected by Shut down output voltage, re-power on to recovery. 11. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 12. Please refer to "DRIVING METHODS OF LED MODULE". 13. 48 type:RCM is on a voluntary basis. Non IC classification Independent LED control gear is not suitable for residential installations. 14. Products sourced from the China regions may not have the BIS logo, please contact your MEAN WELL sales for more information. 15. For A/AB/ABV type need to consider build in using to comply with Type HL application.
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:XLG-240-SPEC 2024-10-11
240W Constant Power Mode LED Driver
BLOCK DIAGRAM
EMI FILTER
I/P
&
RECTIFIERS
FG
PFC CIRCUIT
POWER SWITCHING
PFC CONTROL
O.L.P. O.T.P.
PWM CONTROL
XLG-240 series
PFC fosc : 50~120KHz PWM fosc : 60~130KHz
RECTIFIERS &
FILTER
O.C.P.
DETECTION CIRCUIT
O.V.P.
+V -V
DIM+ DIM(AB Type)
DRIVING METHODS OF LED MODULE
I-V Operating Area
350V 330V 310V 290V 270V 250V 230V 210V 190V 170V
0mA
350mA,342V
700mA,342V
1050mA,228V
700mA,178V
250mA
500mA
750mA
1050mA,178V 1000mA 1250mA
Recommend Performance Region
175V 165V 155V 145V 135V 125V 115V 105V 95V 85V
0mA
700mA,171V
1400mA,90V
550mA
1100mA
1400mA,171V
2100mA,114V
1650mA
2100mA,90V 2200mA
Recommend Performance Region
60V 55V 50V 45V 40V 35V 30V 25V 20V
0mA
2400mA,56V
4280mA,56V 6660mA,36V
4400mA,27V
6660mA,27V
1000mA 2000mA 3000mA 4000mA 5000mA 6000mA 7000mA
Recommend Performance Region
File Name:XLG-240-SPEC 2024-10-11
240W Constant Power Mode LED Driver
DIMMING OPERATION
AC/N(Blue) AC/L(Brown) FG(Green/Yellow)
XLG-240 series
V+(Red) V-(Black)
DIM-(Pink) DIM+(Purple)
3 in 1 dimming function (for AB-Type) Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-:
0 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.)
+
Vo+
+
-
Vo-
-
DIM+ +
Additive Voltage
DIM-
"DO NOT connect "DIM- to Vo-"
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage
+
Vo+
+
-
Vo-
-
DIM+
Additive PWM signal DIM-
"DO NOT connect "DIM- to Vo-"
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
100%
Output current (%)
+ Vo+
VoDIM+
90%
+
80%
70%
-
60%
50%
40%
Additive Resistance
30%
DIM-
20%
10%
"DO NOT connect "DIM- to Vo-"
0%
Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N
(N=driver quantity forsynchronizeddimmingoperation)
Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%.
Dimming input: Additive resistance
2. The output current could drop down to 0% when dimming input is about 0k or 0Vdc, or 10V PWM signal with 0% duty cycle.
3. When PWM frequency >2K HZ ,the lighting will be triggered at 10~15% PWM duty .
File Name:XLG-240-SPEC 2024-10-11
240W Constant Voltage LED Driver
DIMMING OPERATION
AC/N(Blue) AC/L(Brown) FG(Green/Yellow)
XLG-240 series
V+(Red) V-(Black)
DIM-(Pink) DIM+(Purple)
3 in 1 dimming function (for ABV-Type)
Output constant voltage can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.) Applying additive 0 ~ 10VDC
100%
90%
+ Vo+
80%
+
70%
Output voltage (%)
Vo-
60%
-
50%
DIM+
40%
+
Additive Voltage
30%
-
20%
DIM-
10%
"DO NOT connect "DIM- to Vo-"
0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage
Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
100%
90%
+ Vo+
80%
+
70%
Output voltage (%)
Vo-
DIM+
60%
-
50%
40%
Additive PWM signal
30%
20%
DIM-
10%
"DO NOT connect "DIM- to Vo-"
0% 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
Applying additive resistance:
100%
Output voltage (%)
+ Vo+
VoDIM+
90%
+
80%
70%
-
60%
50%
40%
Additive Resistance
30%
DIM-
20%
"DO NOT connect "DIM- to Vo-"
10%
0% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N
(N=driver quantity for synchronized dimming operation)
Dimming input: Additive resistance
Note : 1. Min. dimming level is about 50% of output voltage and the output voltage is not defined when Vout<50%
2. The output voltage could drop down to 0V when dimming input is about 0k or 0Vdc, or 10V PWM signal with 0% duty cycle.
File Name:XLG-240-SPEC 2024-10-11
240W Constant Power Mode LED Driver
XLG-240 series
LOAD (%)
OUTPUT LOAD vs TEMPERATURE
100
80 230VAC Input only
60
40
20
for 48-ABV
110VAC
230VAC
LOAD (%)
100
80 230VAC Input only
60
40
20
for 48-ABV
-40 -30 -20 -10
0
15 30 40 50 60 (HORIZONTAL)
Note:
-40 -30 -20 0
10 30 50 70 90
(HORIZONTAL)
Note:1.If XLG-240 operates in Constant Power mode with the rated current the maximum workable Ta is 50 (Typ. 230VAC) or 40 (Typ. 110VAC)
2.It may has a soft-start status when operation at -30 full load and 110VAC input condition.
STATIC CHARACTERISTIC
100 90 80 70 60 50 40
100 110
140 160 180 200 220 240 260 280 305
INPUT VOLTAGE (V) 60Hz
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 75
Constant Current Mode
1
0.98
0.96
0.94
0.92
115VAC
0.9
230VAC
0.88 277VAC
0.86
0.84
50%
60%
70%
80%
90% 100%
LOAD
PF
EFFICIENCY(%)
TOTAL HARMONIC DISTORTION (THD)
XLG-240-L Model, Tcase at 75
12
10
8
6
115VAC
4
230VAC
277VAC
2
0
50%
60%
70%
80%
90% 100%
LOAD
EFFICIENCY vs LOAD
XLG-240 series possess superior working efficiency that up to 93% can be reached in field applications. XLG-240-L Model, Tcase at 75
96
94
92
90
115VAC
88
230VAC
86
277VAC
84
50%
60%
70%
80%
90% 100%
LOAD
File Name:XLG-240-SPEC 2024-10-11
THD LOAD (%)
240W Constant Power Mode LED Driver
CONSTANT VOLTAGE DIMMING OPERATION:
48-ABV type Note: flicker free design for agricultural lighting
flicker free design for Indoor LED strip lighting
XLG-240 series
Dimming Curve
60.0v 50.0v
Vout 40.0v
30.0v 20.0v 10.0v
0.0v 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V
Vdim
DC Voltage Level
48V
Vout
24V
Rated current
Iout
0A
LIFETIME(Kh)
120 100
80 60 40 20 0
25 30 35 40 45 50 55 60 65 70 75 80 85 90
File Name:XLG-240-SPEC 2024-10-11
240W Constant Power Mode LED Driver
MECHANICAL SPECIFICATION
A-Type
219
208
300±20
195
63 45.8 20
AC/N(Blue) AC/L(Brown) FG(Green/Yellow)
SJOW 17AWGx3C &H05RN-F 1.0mm2
4-4.5 tc
tc
82
XLG-240 series
Case No.:237 Unit:mm Tolerance:±1
300±20
V+(Red) V-(Black) SJOW 17AWGx2C&05RN-F 1.0mm2for H&M type (SOOW 17AWGx2C&H07RN-F 1.0mm2 for L type)
35.5
35
37.8
21.2
AB/ABV-Type
300±20
AC/N(Blue) AC/L(Brown) FG(Green/Yellow)
SJOW 17AWGx3C &H05RN-F 1.0mm2
4-4.5 tc
63 45.8 20
219 208 195
tc
82
300±20
SJOW 17AWGx2C&05RN-F 1.0mm 2for H&M type (SOOW 17AWGx2C&H07RN-F 1.0mm2 for L type)
V+(Red) V-(Black)
DIM-(Pink) DIM+(Purple) UL2517 20AWG*2C
350±20
35.5
35
21.2
37.8 File Name:XLG-240-SPEC 2024-10-11
240W Constant Power Mode LED Driver
Blank-Type
219
208
300±20
195
AC/N(Blue) AC/L(Brown) FG(Green/Yellow)
SJOW 17AWGx3C &H05RN-F 1.0mm2
4-4.5 tc
tc
82
XLG-240 series
300±20
V+(Red) V-(Black) SJOW 17AWGx2C&05RN-F 1.0mm2for H&M type (SOOW 17AWGx2C&H07RN-F 1.0mm2 for L type)
63 45.8 20 35 35.5
Recommend Mounting Direction INSTALLATION MANUAL
File Name:XLG-240-SPEC 2024-10-11
Corel PDF Engine Version 16.1.0.843