USER MANUAL BID 01

Remote Control Overview

This document details the WOODBRIDGE remote control for bidet toilet seats, covering its installation and usage.

The remote control features an LCD screen and various buttons:

• User Settings: USER 1, USER 2 (Save/Recall settings)
• Cleaning Functions: REAR, FRONT (Activates rear/front cleaning), DRY (Activates drying), MASSAGE (Activates massage function)
• Adjustments: PRESSURE (Adjusts water pressure), POSITION (Adjusts nozzle position), WATER (Adjusts water temperature), SEAT (Adjusts seat temperature)
• Control Functions: STOP (Stops current operation), ENERGY SAVER (Activates energy saving mode), NOZZLE CLEANING (Initiates nozzle self-cleaning), FLUSH (Activates full flushing for auto-flush models), AUTO (Activates pre-set automatic cleaning sequences)

The remote also includes a signal indicator [signal-indicator-icon] and an LCD screen displaying status and settings.

Contact Information:

Customer Service Phone: 562-229-0088 (Monday - Friday 9 AM - 5 PM Pacific Time)

Email: help@woodbridgebath.com

Website: www.woodbridgebath.com

Installation Preparation

Remote Control Hanger Installation

To install the remote control hanger:

1. Drill a hole of ⌀ 6mm on the wall with a depth of 35mm. Ensure the location is easily reachable by the user while seated.
2. Peel the adhesive backing from the hanger.
3. Insert an expansion tube into the drilled hole. Mount the hanger to the wall using a screw. Apply the double-faced adhesive tape on the hanger to the wall and tighten the screw.
4. Install batteries into the remote control and place it onto the hanger.

Notice: Avoid installing or using the product in moist environments like steam rooms, or in areas prone to getting wet.

Usage Instruction

Rear/Front Cleaning

Press the "REAR" or "FRONT" button. Water sprays from the nozzle to clean the respective area. The function stops automatically after a cycle. Pressing the "STOP" button immediately halts the operation.

Drying Operation

Press the "DRY" button. Warm air is emitted from the nozzle to dry the user. The function stops automatically after a cycle or when the user leaves the seat.

Massage Function

Press the "MASSAGE" button to activate the massage function. The nozzle moves forward and backward to extend the cleaning scope. Press "MASSAGE" again to stop the function.

Spray Nozzle Position Adjustment

During "REAR" or "FRONT" cleaning, use the nozzle position adjustment buttons ([arrow-left], [arrow-right]) to move the nozzle forward or backward across 5 levels.

Water Pressure Adjustment

During "REAR" or "FRONT" cleaning, use the "+" and "-" buttons to adjust the water pressure for rear and front cleaning across multiple levels.

Energy Saver Mode

Setting Energy Saver Time:

Press the "ENERGY SAVER" button. The LCD screen displays energy saver options (e.g., 3, 6, 9 hours, or Off). You can select a period, for instance, setting energy saver from 9:00 to 15:00.

1. Press "ENERGY SAVER" button: The LCD shows the [energy-saver-icon].
2. Press "ENERGY SAVER" button again: The LCD may show a setting (e.g., "6"). The [energy-saver-icon] disappears after 3 seconds, confirming the setting. The toilet enters energy saver mode during the specified hours. The [power-light-icon] turns off, and the [energy-saver-light-icon] turns on. Normal operation resumes after the set period.
3. Cancel Energy Saver: Press and hold the "ENERGY SAVER" button until the function is cancelled.

Energy Saver Operation: When in energy saver mode, the seat temperature is set to a low status (first level) to conserve energy. If a user sits on the seat, the energy saver mode is paused, and the seat begins to heat immediately. The mode resumes after the user leaves.

Full Flush

(Only for toilets with auto flush function) Press the "FLUSH" button to activate a full flush (?).

Nozzle Cleaning

• Nozzle Self-Cleaning (Quick Press): A quick press of the "NOZZLE CLEANING" button cleans the nozzle for a short period and moves it to the front position without spraying. Users can continue manual cleaning.
• Nozzle Self-Cleaning (Long Press): A long press of the "NOZZLE CLEANING" button cleans the nozzle for 90 seconds without moving forward.

Automatic Deodorization

(Only for toilets with auto deodorization function) The deodorization function activates automatically when a user sits on the seat and stops 3 seconds after the user leaves. It also stops during the drying function.

Temperature Adjustment

• Dry Temperature Adjustment: Press the "DRY" button to adjust the drying temperature. The LCD display shows levels 1-5 ([level-1-5-display]); no display ([no-display]) indicates normal temperature. Adjust levels using up/down cycles.
• Water Temperature Adjustment: Press the "WATER" button to adjust the water temperature for cleaning. The LCD display shows levels 1-5 ([level-1-5-display]); no display ([no-display]) indicates normal temperature. Adjust levels using up/down cycles.
• Seat Temperature Adjustment: Press the "SEAT" button to adjust the seat temperature. The LCD display shows levels 1-5 ([level-1-5-display]); no display ([no-display]) indicates normal temperature. Adjust levels using up/down cycles.

User Code Function

(Only for toilets with User Code function) Long press "USER 1" or "USER 2" to save parameters like water pressure, nozzle position, dry/water/seat temperature, and massage status. A quick press of "USER 1" or "USER 2" recalls the saved settings.

Hardware Configurations

• Configuration 1: Load Settings User 1 / Load Settings User 2
• Configuration 2: Load & Act Male Rear Wash / Load & Act Female Bidet Wash

Hardware 1 supports loading user settings only. Hardware 2 supports loading and acting user settings simultaneously. Hardware 1 is compatible with V8100 series, while Hardware 2 is compatible with all models except V8100 series.

Auto Lid/Seat Open/Close

(Only for toilets with this function) Press the [auto-lid-close-button] to close the seat cover. Press the [auto-lid-open-button] to open the lid and close the seat, or open the lid and seat.

Auto Function

(Only for toilets with auto flush function) The full-automatic function is activated by three [auto-button]s. Users can pre-set nozzle position, water pressure, and temperature. The full-automatic function then runs automatically when the corresponding button is pressed.

• Auto Rear Cleaning: Rear cleaning (90s) → Drying (180s) → Automatic stop.
• Auto Front Cleaning: Front cleaning (90s) → Drying (180s) → Automatic stop.
• Auto Rear and Front Cleaning: Rear cleaning (90s) → Front cleaning (90s) → Drying (180s) → Automatic stop.

Combination Buttons

• Night Light: Press "STOP" then "DRY" to turn the night light off ([night-light-icon] off). Repeat to switch between off and intelligent states.
• Quiet Mode: Press "STOP" then "MASSAGE" to turn off the buzzer ([buzzer-icon] off) for quiet operation. Repeat to re-enable the buzzer.
• User Code Setting: To set a user code (1-9) to avoid interference with multiple toilets, press "STOP" then "REAR". Adjust water pressure buttons for the code. Press "STOP" then "REAR" again to save. The sum of water pressure and position levels forms the user code.
• Automatic Flush Button: Press "STOP" then "FLUSH" to start or close automatic flushing. The toilet flushes automatically after detecting a user for over 6 seconds and after the user leaves for over 3.5 seconds.
• Auto Open/Close: Press "STOP" then the designated button to enable/disable auto open/close for the toilet seat. This function is off by default.

Remarks:

• Button presses are confirmed by a flashing [signal-indicator-icon] and a "click" sound from the [buzzer-icon]. If no signal or click is heard, re-press the button, ensuring correct direction.
• In case of a power cut during wand operation, wait for power reset ([power-light-icon]). If the power cut is prolonged, gently push the wand back by hand to avoid damage.
• When functions like front cleaning, rear cleaning, or drying are active, the body should touch the seat, and a "click" sound will confirm operation. The nozzle may spray for 1-2 seconds after the user stands up; press "STOP" before standing.
• Use the nozzle self-cleaning function after the user leaves the seat. If no other button is pressed, the nozzle retracts after 10 minutes or when the user sits again.

Set Auto Function

Set Automatic Rear Cleaning Function

The default setting includes water pressure, nozzle position, water temperature, drying temperature, and seat temperature on level three, with massage off. Users can customize these settings.

1. Adjust water pressure, nozzle position, and temperatures using the function buttons. Enable/disable the massage function.
2. After setting, long press the automatic rear cleaning button for 3 seconds to save.
3. To activate, quick press the saved setting button. The LCD will display the saved parameters. The toilet will then perform rear cleaning (90s) followed by drying (180s) automatically.
4. During automatic rear cleaning, levels, temperatures, and massage status can be changed. Press "REAR" for 3 seconds to save new settings.

Set Automatic Front Cleaning Function

1. Adjust nozzle position, water pressure, and temperature settings. Enable/disable the massage function.
2. Long press the automatic front cleaning button for 3 seconds to save the settings.
3. To activate, quick press the saved setting button. The LCD will display the saved parameters. The toilet will then perform rear cleaning (90s) followed by drying (180s) automatically.
4. During automatic front cleaning, levels, temperatures, and massage status can be changed. Press "FRONT" for 3 seconds to save new settings.

Set Automatic Rear and Front Cleaning Combination Function

This function combines rear cleaning (90s), front cleaning (90s), and drying (180s). Users can adjust levels and temperatures for each stage.

1. After sitting on the toilet, press the automatic Rear and Front cleaning button. It starts with rear cleaning (approx. 90s).
2. During rear cleaning, adjust nozzle position, water pressure, drying temperature, seat temperature, and massage function. The remote saves these parameters for the first stage. If multiple adjustments are made, the latest parameter is saved.
3. After rear cleaning, the toilet automatically proceeds to front cleaning (approx. 90s). Adjustments made here are saved for the second stage.
4. After front cleaning, the toilet automatically proceeds to drying (approx. 180s). Adjust drying temperature; the remote saves the latest parameter for the third stage.
5. After setting all parameters, quick press the [auto-button] afterwards. The LCD displays the saved settings, and the toilet performs rear cleaning, front cleaning, and drying automatically with a single button press. Repeat steps 1-3 to change settings.