User Guide for Zhier models including: ZE-CPE1000 Wireless Bridge, ZE-CPE1000, Wireless Bridge, Bridge
Shenzhen Zhier Network Technology Co., Ltd. ZE-CPE1000 2A5WF-ZE-CPE1000 2A5WFZECPE1000 ze cpe1000
1. A-BA BledL L 2. resetled 3. 1A1 B1LEDL L11 A,BLED1 AB Link LAN1 LAN2 PWR LED LED LED RST RST link H, L A,BAB 1-5sled0-F 10s LED A IP B IP 2.4 ID 5.8 ID 0 192.168.255.100 192.168.255.200 0 0 1 192.168.255.101 192.168.255.201 1 165 2 192.168.255.102 192.168.255.202 2 161 3 192.168.255.103 192.168.255.203 3 157 4 192.168.255.104 192.168.255.204 4 153 5 192.168.255.106 192.168.255.205 5 6 192.168.255.106 192.168.255.206 6 149 48 7 192.168.255.107 192.168.255.207 7 44 8 192.168.255.108 192.168.255.208 8 40 9 192.168.255.109 192.168.255.209 9 36 a 192.168.255.110 192.168.255.210 10 140 b 192.168.255.111 192.168.255.211 11 132 C 192.168.255.112 192.168.255.212 13 124 D 192.168.255.113 192.168.255.213 96 116 E 192.168.255.114 192.168.255.214 50 108 F 192.168.255.115 192.168.255.215 55 100 - 1. 2.,PCip,ip 192.168.255.x, 3.,IE ip,, , 4.[]-[] [], Wireless Bridge Digital Bridge-A Master Mode IPC receiver PoE Adapter Switch Computer Camera Usually near NVR LAN PoE +/-(1-5sL)AN1(POE) LAN2(PoE) DC(9-12V) RST(10s) A B Digital Bridge-B Slave Mode IPC transmitter) PoE Adapter Switch Computer Camera At the IPC end LAN PoE +/-(1-5sL)AN1(POE) LAN2(PoE) DC(9-12V) RST(10s) A B 1. First Set A B A-B mode DIP switch, led L appears and blinks. After the disappearance of L shows an arrangement remain successful. 2. The reset button to set the led digital display, click the startup configuration status, then click the automatic increase. Can be continuously increased 3. Assume that a pair of bridges with a number of 1 is configured After A set to 1, after the B set to 1, during the LED will flash, L application configuration appears blinking, wait, L foot after flashing into a digital 1, 1 will continue to flash until the A, B are connected After the success, the LED display 1 is always on, not flashing, indicating that the AB has been successfully networked. Link LAN1 LAN2 Bridge connection is successful, link lights, not connected Off Turning on the lighting data, the communication flashing, off data nowhere Turning on the lighting data, the communication flashing, off data nowhere PWR LED LED Power indicator, power on Display H, expressed configured to manually set state L displayed and flashes, represents settings LED Flashing, it indicates to modify the configuration, or is connected to the Round light RST RST A, B status lights, light that is not mode A, mode B light that 1-5s press, led digital automatic increase, 0-F from circulation Press over 10s, release the reset, the system automatically restart LED A IP B IP 2.4 ID 5.8 ID 0 192.168.255.100 192.168.255.200 0 0 1 192.168.255.101 192.168.255.201 1 165 2 192.168.255.102 192.168.255.202 2 161 3 192.168.255.103 192.168.255.203 3 157 4 192.168.255.104 192.168.255.204 4 5 192.168.255.106 192.168.255.205 5 6 192.168.255.106 192.168.255.206 6 153 149 48 7 192.168.255.107 192.168.255.207 7 44 8 192.168.255.108 192.168.255.208 8 40 9 192.168.255.109 192.168.255.209 9 36 a 192.168.255.110 192.168.255.210 10 140 b 192.168.255.111 192.168.255.211 11 132 C 192.168.255.112 192.168.255.212 13 124 D 192.168.255.113 192.168.255.213 96 116 E 192.168.255.114 192.168.255.214 50 108 F 192.168.255.115 192.168.255.215 55 100 FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Statement To maintain compliance with FCC's RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 20cm the radiator your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.Corel PDF Engine Version 17.0.0.491