Eaton C440-COM-ADP :: COMMUNICATION ADAPTER :: Gexpro
Installation Leaflet IL04210006E Effective July 2010 Supersedes April 2010 C440-COM-ADP Communication Adapter Installation: The C440-COM-ADP communication adapter is designed to be used in industrial applications and installed in accordance with this document. The device is intended for use in clear, dry environments. Mount the Comm. Module With Com-Adapter The communication adapter can combine with various communication modules for customer application requirements. See TABLE 1 for optional comm modules available. To mount the communication module to a comunication adapter, the following procedure must be preformed. · Place the tabs opposite the communication module into the lower slots provided on the communica- tion adapter right side. · Pivot the module on the lower tabs toward the communication adapter. · Gently press the communication module and communication adapter together. So the combination of communication module and communication adapter will become an integrated communication module kit. TABLE 1. Optional Communication Module to Combine with Communication Adapter Description Modbus Communication Module with 120Vac Modbus Communication Module with 24Vdc DeviceNet Communication Module with 120Vac I/O DeviceNet Communication Module with 24Vdc I/O PROFIBUS-DP Communication Module with 120Vac I/O PROFIBUS-DP Communication Module with 24Vdc I/O Eaton Catalog # C441N, Style # 3-2373-003B C441P, Style # 3-2373-004B C441K, Style # 3-2373-001B C441L, Style # 3-2373-002B C441S, Style # 3-2398-001B C441Q, Style # 3-2398-001B Mount the Communication Module Kit in Application Field The communication adapter provides 2 optional mounting methods for the customer. · 35mm DIN Rail Mounting · Panel mount features 85x25mm with two # 10-24 x .500 screws Connect the Communication Adapter to C440 EOL/S611 Soft Starter · See FIGURE 1 for wiring information. · Reference installation leaflet for appropriate communication module for additional wiring information. · Use wire with minimum 600V insulation. · For communication connections, use 16 AWG shielded, twisted pair. Communication Module Kit setup and configuration The communication module kit requires no extra setup or configuration for normal operation. For more information, refer to the installation leaflet for the appropriate communication module. Please go to www.eaton.com. IL04210006E July 2010 C440-COM-ADP Communication Adapter FIGURE 1. Terminal Connection Diagram - 24V dc + C440 - XCOM 1 - 24V dc 4 - COM 5 - DI 6 - DO C440-COM-ADP 1 - COM 2 - 24V dc 1 - COM 2 - D1 4 - D0 5 - 24V dc CM oo md mu ul ne i c a t i o n TABLE 3. Communication Terminal Connection Specification PIN CIRCUIT EIA-485 WIRE # Name COLOR DESCRIPTION 1 COM C/C' Grey Signal and power supply com. 2 DI 3 N/C B/B' Yellow Transceiver terminal 1, V1 Voltage, Data+ (V1>V0 for binary 1 [Off] state) 4 D0 A/A' 5 24V dc Brown Red Transceiver terminal 0, V0 Voltage, Data+ (V0>V1 for binary 1 [ON] state) Power Supply 24V dc S611 Modbus Connector 1 - 24V dc 2 - D0 4 - D1 5 - COM C440-COM-ADP 1 - COM 2 - 24V dc 1 - COM 2 - D1 4 - D0 5 - 24V dc CM oo md mu ul ne i c a t i o n C440-COM-ADP S611 Modbus Connector 1 - 24V dc 2 - D0 1 - COM CM oo 2 - 24V dc md mu ul ne i c a 1 - COM t i 2 - D1 o n 4 - D1 5 - COM 4 - D0 5 - 24V dc Note: "24V dc" points in 2 pole connector and 5 pole connector are tied together internally, as well as corresponding "COM" points in C440-COM-ADP. TABLE 2. Power Terminal Connection Specifications PIN # CIRCUIT RECOMMENDED DESCRIPTION WIRE COLOR 1 COMMON Black Power supply common 2 24V dc Red Power supply 24V dc TABLE 4. Environmental Ratings of the Module Transportation Temperature and Storage Humidity -50°C to 85°C (-58°F to 185°F) 5-95% non-condensing Temperature -40°C to 65°C (-40°F to 149°F) Humidity 5-95% non-condensing Operating Altitude Above 2000 meters (6600 feet) Consult factory Shock IEC 60068-2-27 15G any direction for 11 milliseconds Vibration IEC 60068-2-6 3G in any direction Pollution Degree 3 TABLE 5. Approvals/Certifications Agency Certifications UL508 CUL (CSA C22.2 No. 14) CE (Low Voltage Directive) RoHS TABLE 6. Module Electrical requirements Voltage Range Current Draw 18 - 30 Vdc Approx. 30 mA Notes: For use with Eaton UL Listed Power Supply Catalog Numbers, PSS55A, PSS55B, PSS55C, or PS160E. Any UL Listed isolated power supply with a maximum of 30Vdc out may be used, provided that a UL Listed of Recognized Fuse rated at no more than 3A maximum be installed. Eaton Corporation Electrical Sector 1000 Cherrington Parkway Moon Township, PA 15108 United States 877-ETN-CARE (877-386-2273) Eaton.com © 2010 Eaton Corporation All Rights Reserved Printed in USA Publication No. IL04210006E / Rev003 July 2010 PowerChain Management is a registered trademark of Eaton Corporation. All other trademarks are property of their respective owners.Acrobat Distiller 7.0 (Windows)