applications, read the instruction manual well to select the proper setting and connection. 1. Remove the ignition key and disconnect the negative - terminal of the battery to prevent short circuits. 2. Set the unit according to the intended usage. 3. Connect the input and output wires of the units. 4. Connect the speaker wires. 5.
PHONES (044) 360-7-130 (050) 336-0-130 (063) 788-0-130 (067) 233-0-130 (068) 282-0-130
Internet store of autogoods
ICQ 294-0-130 597-0-130
SKYPE km-130
CAR RECEIVERS -- Receivers · Media receivers and stations · Native receivers · CD/DVD changers · FM-modulators/USB adapters · Flash memory · Facia plates and adapters · Antennas · Accessories | CAR AUDIO -- Car audio speakers · Amplifiers · Subwoofers · Processors · Crossovers · Headphones · Accessories | TRIP COMPUTERS -- Universal computers · Model computers · Accessories | GPS NAVIGATORS -- Portable GPS · Built-in GPS · GPS modules · GPS trackers · Antennas for GPS navigators · Accessories | VIDEO -- DVR · TV sets and monitors · Car TV tuners · Cameras · Videomodules · Transcoders · Car TV antennas · Accessories | SECURITY SYSTEMS -- Car alarms · Bike alarms · Mechanical blockers · Immobilizers · Sensors · Accessories | OPTIC AND LIGHT -- Xenon · Bixenon · Lamps · LED · Stroboscopes · Optic and Headlights · Washers · Light, rain sensors · Accessories | PARKTRONICS AND MIRRORS -- Rear parktronics · Front parktronics · Combined parktronics · Rear-view mirrors · Accessories | HEATING AND COOLING -- Seat heaters · Mirrors heaters · Screen-wipers heaters · Engine heaters · Auto-refrigerators · Air conditioning units · Accessories | TUNING -- Vibro-isolation · Noise-isolation · Tint films · Accessories | ACCESSORIES -- Radar-detectors · Handsfree, Bluetooth · Windowlifters · Compressors · Beeps, loudspeakers · Measuring instruments · Cleaners · Carsits · Miscellaneous | MOUNTING -- Installation kits · Upholstery · Grilles · Tubes · Cable and wire · Tools · Miscellaneous | POWER -- Batteries · Converters · Start-charging equipment · Capacitors · Accessories | MARINE AUDIO AND ELECTRONICS -- Marine receivers · Marine audio speakers · Marine subwoofers · Marine amplifiers · Accessories | CAR CARE PRODUCTS -- Additives · Washer fluid · Care accessories · Car polish · Flavors · Adhesives and sealants | LIQUID AND OIL -- Motor oil · Transmission oil · Brake fluid · Antifreeze · Technical lubricant
In store "130" you can find and buy almost all necessary goods for your auto in Kyiv and other cities, delivery by ground and postal services. Our experienced consultants will provide you with exhaustive information and help you to chose
the very particular thing. We are waiting for you at the address
http://130.com.ua
KAC-X1R KAC-PS1D
MONO DIGITAL POWER AMPLIFIER 7 page 2-8
INSTRUCTION MANUAL
AMPLIFICATEUR MONO NUMÉRIQUE 7 page 10-16
MODE D'EMPLOI
a AMPLIFICADOR DE POTENCIA DIGITAL MONOFÓNICO 7 página 18-24 130.com.u MANUAL DE INSTRUCCIONES
Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new power amplifier.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KAC-X1R/ KAC-PS1D Serial number
US Residence Only
Register Online
Register your Kenwood product at www.kenwoodusa.com
© B64-3522-00/00 (KV/EV) Autogood products Internet store "130"
Safety precautions
2WARNING
To prevent injury or fire, take the following precautions: · Mounting and wiring this product requires skills and experience. For safety's
sake, leave the mounting and wiring work to professionals.
Cleaning the unit If the front panel gets dirty, turn off the power and wipe the panel with a dry silicon cloth or soft cloth.
2CAUTION
· When extending the battery, or ground wires, make sure to use automotivegrade wires or other wires with the range of 10 mm2 (AWG 8) to 25 mm2 (AWG 4) to prevent wire deterioration and damage to the wire coating.
Do not wipe the panel with a hard cloth or a cloth dampened by volatile solvents such as paint thinner and alcohol. They can scratch the surface of the panel and/or cause the indicator letters to peel off.
· To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit.
· If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer.
To prevent battery rise When the unit is used in the ACC ON position without turning the engine ON, it depletes the battery. Use it after starting the engine.
· Do not touch the unit during use because the surface of the unit becomes hot and may cause burns if touched.
Protection function
2CAUTION
To prevent damage to the machine, take the following precautions: · Be sure the unit is connected to a 12V DC power supply with a negative
ground connection. · Do not open the top or bottom covers of the unit.
There is a Protection function installed in the unit to protect the unit and speakers from various problems. When Protection operates, the display informs you of the condition.
Display "E-01"
Informations When the inside of the unit is overheating.
When the unit has failed and direct current voltage is generated to the speaker's output.
· Do not install the unit in a spot exposed to direct sunlight or excessive heat
"E-02"
NOTE
or humidity. Also avoid places with too much dust or the possibility of water
Turn the power OFF and release the protection. If the "E-02" code does not disappear,
splashing.
contact your Kenwood dealer.
· When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction.
· To prevent a short circuit when replacing a fuse, first disconnect the wiring harness.
a NOTE .u · If you experience problems during installation, consult your Kenwood dealer.
· If the unit does not seem to be working right, consult your Kenwood dealer.
FCC WARNING
m This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could
o lose the authority to operate this equipment if an unauthorized change or
modification is made.
.c FCC NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to
0 radio communications, if it is not installed and used in accordance with the
instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
3 or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more
1 of the following measures:
"E-03"
"E-99" "VOLT" display is blinked.
When the speaker cord is shorted. When the speaker output is in contact with the vehicle ground. When a system error occurs. Press the Reset button. If the "E-99" code does not disappear, contact your Kenwood dealer.
When voltage gets out of operation range.
Wiring · Take the battery wire for this unit directly from the battery. If it's connected to
the vehicle's wiring harness, it can cause blown fuses etc.
· If a buzzing noise is heard from the speakers when the engine is running, connect a line noise filter (optional) to each of the battery wire.
· Do not allow the wire to directly contact the edge of the iron plate by using Grommets.
· Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the battery`s negative - terminal. Do not turn the power on if the ground wire is not connected.
· Be sure to install a protective fuse in the power cord near the battery. The protective fuse should be the same capacity as the unit's fuse capacity or somewhat larger.
· For the power cord and ground, use a vehicle type (fireproof ) power wring cord with a current capacity greater than the unit's fuse capacity. (Use a power wiring cord with a diameter between 10 mm2 (AWG 8) to 25 mm2 (AWG 4).)
· When more than one power amplifier are going to be used, use a power supply wiring wire and protective fuse of greater current-handling capacity than the total maximum current drawn by each amplifier.
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
Speaker Selection
· Connect the equipment into an outlet on a circuit different from that to which
· The rated input power of the speakers that are going to be connected should
the receiver is connected.
be greater than the maximum output power (in Watts) of the amplifier. Use of
· Consult the dealer or an experienced radio/TV technician for help.
speakers having input power ratings that are less than the output power of
the amplifier will cause smoke to be emitted as well as damage.
NOTE This Class B digital apparatus complies with Canadian ICES-003.
· Use speakers that have an impedance of 1 or greater. When more than one set of speakers are going to be used, calculate the combined impedance of the speakers and then connect suitable speakers to the amplifier.
Information on Disposal of Old Electrical and Electronic Equipment (applicable for EU countries that have adopted separate waste collection systems)
Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment.
This Product is not installed by the manufacturer of a vehicle on the production line, nor by the professional importer of a vehicle into an EU Member State.
4
4 8
4 4 2
Combined impedance
2 English
Autogood products Internet store "130"
Installation
340 mm 279 mm
Accessories Part name
Self-tapping screws (ø5 × 18 mm)
Hexagon Wrench (Large)
Hexagon Wrench (Small)
External View Number of Items 4
1 1
Installation procedure
Since there are large variety of settings and connections possible according to
194.5 mm 225 mm
applications, read the instruction manual well to select the proper setting and
connection.
1.Remove the ignition key and disconnect the negative - terminal of the
battery to prevent short circuits.
2.Set the unit according to the intended usage.
3.Connect the input and output wires of the units.
4.Connect the speaker wires.
5.Connect the power wire, power control wire and grounding wire following this
order.
Ø6
6.Install the installation fittings in the unit.
7.Attach the unit.
8.Install the remote controller.
9.Connect the negative - terminal of the battery.
Self-tapping screw (ø5 × 18 mm)
Dressing cover Self-tapping screw (ø5 × 18 mm)
ø7 ø10 mm
Hexagon Wrench (Small)
a Hexagon socket
head cap screw
.u (M4 × 8 mm)
130.com ø5 mm
Installation board, etc. (thickness : 15 mm or more)
2CAUTION
· Do not install in the below locations; (Unstable location, In a location that interferes with driving, In a location that gets wet, In a dusty location, In a place that gets hot, In a place that gets direct sunlight, In a location that gets hit by hot air)
· Do not install the unit under the carpet. Otherwise heat build-up occurs and the unit may be damaged.
· Install this unit in a location which allows heat to easily dissipate. Once installed, do not place any object on top of the unit.
· The surface temperature of the amplifier will become hot during use. Install the amplifier in a place where people, resins, and other substances that are sensitive to heat will not come into contact with it.
· This unit has cooling fan to decrease the internal temperature. Do not mount the unit in a place where the cooling fan and ducts of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction.
· When making a hole under a seat, inside the trunk, or somewhere else in the vehicle, check that there is nothing hazardous on the opposite side such as a gasoline tank, brake pipe, or wiring harness, and be careful not to cause scratches or other damage.
· Do not install near the dashboard, rear tray, or air bag safety parts. · The installation to the vehicle should securely fasten the unit to a place in
which it will not obstruct driving. If the unit comes off due to a shock and hits a person or safety part, it may cause injury or an accident. · After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal lamps and windshield wipers operate normally.
Remote controller (Accessory of KAC-PS1D. Optional accessory for KAC-X1R.)
Mounting bracket Remote controller
Accessories Part name
Remote cable (6.0 m : 19.7 ft)
Remote controller
Self-tapping screw (ø2.6 × 12 mm)
Mounting bracket
Self-tapping screws (ø2.6 × 12 mm)
External View Number of Items 1 1
1 2
Autogood products Internet store "130"
English 3
25 25 25
25 25 25
Connection
2WARNING To prevent fire caused by a short in the wiring, connect a fusible link or breaker nearby the battery's positive terminal.
CENTER UNIT (CD receiver, etc.)
RCA cable*
Power control wire
Left input
2CAUTION
· If sound is not output normally, immediately
SPEAKER OUTPUT
turn power off and check connections.
· Be sure to turn the power off before changing the setting of any switch.
FUSE (25As3)
POWER IN
LINE OUT FILTER
REMOTE
OFF
ON
RESET
· If the fuse blows, check wires for shorts, then
replace the fuse with one of the same rating. · Check that no unconnected wires or
Battery wire*
connectors are touching the car body. Do
Protective Fuse*
not remove caps from unconnected wires or
connectors to prevent short circuits.
· Connect the speaker wires to appropriate
speaker connectors separately. Sharing the
negative wire of the speaker or grounding
speaker wires to the metal body of the car can cause this unit to fail. · After installation, check that the brake lamps, winkers, and wipers work properly.
Battery
a * Commercially available parts
Ground wire*
.u About the Lead Terminals
m 1 Wire Thicknesses You can use wires with the following thicknesses:
Battery wire and ground wire
o Power control wire and speaker wire
AWG 4 AWG 8 AWG 6 AWG 18
.c 2 Strip the wire Make a cut in the wire sheath (insulator made from vinyl, etc.) at the position 7-10 mm away from the end of the wire, and then remove the unnecessary portion of the sheath by twisting it.
0 3 Install the wire Loosen the screw using the supplied hexagon wrench. 3 Insert the conductor of the wire in the terminal hole, and then 1 tighten the screw.
7 10 mm (9/32" 3/8")
Hexagon Wrench (Large)
LINE IN LINE OUT
Right input Subwoofer (L + R)
Hexagon Wrench (Small)
Remote cable connection (Accessory of KAC-PS1D. Optional accessory for KAC-X1R.)
2CAUTION
· Before connecting the remote controller cables, always turn the Bass boost level knob all the way to the left.
Remote cable (6.0 m : 19.7 ft)
FUSE (25As3)
POWER IN
SPEAKER OUTPUT
LINE OUT FILTER
REMOTE
OFF
ON
RESET
LINE IN LINE OUT
Remote controller
4 English
Autogood products Internet store "130"
Multi Amplifier with Remote cable connection (Accessory of KAC-PS1D. Optional accessory for KAC-X1R.)
You can control the Bass boost level of the second and subsequent Slave amplifiers simultaneously from the Master amplifier. The volume level of each amplifier is determined by the setting of the Master amplifier (INPUT SENSITIVITY, boost level of the remote controller).
Setting the Master amplifier 1.Adjust the "INPUT SENSIVITY" to the output of
the center unit to be connected. 2.Set the LPF frequency and Bass boost level. 3.Turn the "LINE OUT FILTER" switch "ON".
Setting the Slave amplifier 1.Turn the "LINE OUT FILTER" switch "OFF". 2.Adjust the "INPUT SENSIVITY". · To adjust the Slave amplifier to the same
volume as the Master amplifier, adjust the "INPUT SENSIVITY" to "0.2 V (max.)".
CENTER UNIT (CD receiver, etc.)
Power control wire
RCA cable*
LPF ON
OFF
100 150 70
1
2
3
0.5
4
40
200
LPF FREQUENCY(Hz)
(MIN)5
0.2(MAX)
INPUT SENSITIVITY(V)
Remote cable
FUSE (25As3)
Master amplifier
POWER IN
25
25
25
SPEAKER OUTPUT
LINE OUT FILTER
REMOTE
OFF
ON
RESET
LINE IN LINE OUT
LINE OUT FILTER
Remote controller
2CAUTION
Extension wire*
OFF
ON
· Before connecting the remote controller cables, always turn the Bass boost level knob all the way to the left.
* Commercially available parts
LPF
100 150
70
ON
1
2
3
0.5
4
25
25
a FUSE (25As3)
POWER IN
25
25
25
25
1SSl3laavveeaammpp0lliiffiieerr .com.u FUSE(25As3)
POWER IN
40
200 (MIN)5
0.2(MAX)
LPF
INPUT
OFF
FREQUENCY(Hz)
SENSITIVITY(V)
SPEAKER OUTPUT
LINE OUT FILTER
REMOTE
OFF
ON
RESET
LINE IN LINE OUT
LINE OUT FILTER
OFF
ON
LPF ON
OFF
100 150 70
1
2
3
0.5
4
40
200
LPF FREQUENCY(Hz)
(MIN)5
0.2(MAX)
INPUT SENSITIVITY(V)
SPEAKER OUTPUT
LINE OUT FILTER
REMOTE
OFF
ON
RESET
LINE IN LINE OUT
LINE OUT FILTER
OFF
ON
RCA cable*
Autogood products Internet store "130"
English 5
Controls
0 4 8 12 16 20
30 50 100 200 400
LPF OPERATION
1k [Hz]
200Hz 150Hz 100Hz
70Hz 40Hz
INFORMATION DISPLAY
VOLTAGE
CURRENT
DEMO
TEMPERATURE
POWER IN FUSE (25A3)
SPEAKER OUTPUT
{ |} ~
MENU ENTER
30
50
1
2
3
0.5
4
15
60
ISF FREQUENCY(Hz)
40
200 (MIN)5
0.2(MAX)
B.R.F
INPUT
FREQUENCY(Hz) SENSITIVITY(V)
PHASE
ISF
180
ON
BRF
LPF
-12dB
ON
-6dB
100 150 70
40
200
0
OFF
OFF
OFF
LPF
FREQUENCY(Hz)
REMOTE LINE OUT FILTER
OFF
ON
LINE IN LINE OUT
Remote controller (Accessory of KAC-PS1D. Optional accessory for KAC-X1R.)
25 25 25
SPEAKER OUTPUT
FUSE (25As3)
POWER IN
p
q rs
t
LINE OUT FILTER
REMOTE
OFF
ON
RESET
uv w
LINE IN LINE OUT
x
y
z
NOTE
@ Control knob
The control panel locates under the dressing cover. Remove the cover to access to its controls for adjustment. (See page 3)
1 Fuse (25 A × 3)
a 2 Battery terminal
3 Ground terminal
.u 4 Power control terminal Controls the unit ON/OFF. NOTE Controls the unit power. Be sure to connect it with all the systems. 5 Speaker output terminals
m As this unit accepts speakers with a minimum impedance of 1 ohm, connect
speakers with 1-ohm or higher impedance to these terminals.
o 2CAUTION
The rated input of the speakers should be no less than the maximum output of the amplifier. Otherwise malfunction may result.
.c 6 REMOTE terminal Connects the Remote cable. NOTE 0 Use the Remote cable of the accessory. 7 LINE OUT FILTER switch
Changing over the audio signal output to the "LINE OUT" terminal.
3 ON position:
The audio signal adjusted when setting "LPF", "INPUT SENSIVITY" control and
1 Bass boost is output to the "LINE OUT" terminal.
Allows you to switch between and determine Menu System items.
# PHASE switch When this switch is set "180°" (Reverse) the speaker output phase is reversed.
$ ISF (infrasonic filter) switch When this switch is set to "ON", the inaudible, ultralow frequencies below the frequency set with the "ISF FREQUENCY" control are cut off. This improves the reproduction performance of the speakers by eliminating unnecessary oscillations which will not become sound.
% ISF FREQUENCY control Sets the cutoff frequency when the "ISF" switch is set to "ON".
^ BRF (band reject filter) switch When this switch is set to "-6dB"/"-12dB", frequencies in the band set with the "B.R.F. FREQUENCY" control are rejected and eliminated. The band rejection allows to reduce resonance inside the vehicle compartment and standing waves. (page 7)
& B.R.F. FREQUENCY control Sets the rejection frequency when the "BRF" switch is set to "-6dB"/"-12dB". (page 7)
* LPF(Low-Pass Filter) switch This switch allows to apply low-pass filtering to the speaker outputs. · OFF position: The entire bandwidth is output without filtering. · ON position: The filter outputs the band of lower frequencies than the frequency set with the "LPF FREQUENCY" control.
( INPUT SENSITIVITY control Set this control according to the pre-output level of the center unit connected with this unit.
OFF position: The audio signal input from the "LINE IN" terminal is output to the "LINE OUT" terminal (through output).
NOTE
For the pre-output level, refer to the <Specifications> in the instruction manual of the center unit.
2CAUTION
The volume of the audio output to the "LINE OUT" terminal is different in "ON" and "OFF" position. Remember this when changing the "LINE OUT FILTER" switch from "ON" to "OFF".
8 RESET button Resets the microprocessor of the unit.
) LPF(Low-Pass Filter) FREQUENCY control Sets the cutoff frequency when the "LPF" switch is set to "ON".
* BOOST LEVEL (Bass boost level) control Sets the level by which the low frequency range should be boosted.
( Power indicator
9 LINE IN terminal
0 LINE OUT terminal The audio signal set with the "LINE OUT FILTER" switch will be output.
) FREQUENCY (Bass boost frequency) control Sets the center frequency around which the low frequency range should be
boosted.
! Power indicator Lights when the POWER switch is turned On. The indicator flashes several seconds when the POWER switch is turned On or when the Protection function is activated.
6 English
Autogood products Internet store "130"
Menu System
Display mode
You can set up the display items as follows:
1 Select a display item
Turn the Control knob. The display items are switched in the following sequence.
Display "VOLT" "CURRT" "TEMP" "DEMO"
Information Indicates the source voltage (V). Indicates the current consumption (A). Indicates the internal temperature (°F/°C). Allows you to set up the display demonstration.
NOTE
When the internal temperature is -22°F/-30°C or less, "-22F"/"-30C" is displayed.
Display Item Adjustment
You can adjust the display items as follows.
1 Select a display item
Turn the Control knob.
2 Adjust the display item
Press the Control knob. The setup items and set values are switched as follows.
Display "TEMP" "DEMO"
Range
---F (Fahrenheit) / ---C (Centigrade)
OFF/ ON
Adjustment Item
The Fahrenheit or Centigrade temperature unit can be selected for the Display mode.
When set to ON, the "VOLT", "CURRT", and "TEMP" items are displayed repeatedly.
NOTE Normally the setting listed at the top of the chart is the original setting.
Band Reject Filter
130.com.ua
The acoustic properties of vehicle compartment tend to cause oscillation due to resonance or unclearness of sound due to standing waves at certain frequencies. The band reject filter can solve the problems of resonance or unclear sound with minimum influence on the sound quality because it eliminates only the frequencies causing resonance or standing waves.
0 dB
Frequency
Adjustment method: The band reject filter cuts only the limited frequencies to minimize influence on the sound quality. Therefore, its effect cannot be obtained unless the cutoff frequencies are set accurately to the frequencies causing resonance and standing waves. The band reject filter can be adjusted according to what you feel through your ears, but we recommend the use of a signal generator or a spectrum analyzer with a fine frequency measurement capability for the adjustment.
· Adjustment using a signal generator: Output a sine wave, vary its frequency to find the frequencies at which the vehicle compartment resonates or volume increases (standing waves occur), and set the B.R.F. FREQUENCY control to the position with which the resonance and standing waves disappear.
· Adjustment using a spectrum analyzer: Output white noise (sound in which all frequencies are at a certain level), find the peak frequency observed on the spectrum analyzer, and set the B.R.F. FREQUENCY control to the position with which the peak observed on the spectrum analyzer disappears.
Autogood products Internet store "130"
English 7
Troubleshooting Guide
What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems.
PROBLEM No sound. (Blown fuse.)
The output level is too small (or too large). The sound quality is bad. (The sound is distorted.)
The Remote Controller does not function.
POSSIBLE CAUSE · Input (or output) cables are disconnected. · Protection circuit may be activated. · Volume is too high. · The speaker cord is shorted.
· The input sensitivity adjusting control is not set to the correct position.
· The speakers wire are connected with wrong + /-polarity.
· A speaker wire is pinched by a screw in the car body.
· The switches may be set improperly. · The Remote Cable is disconnected.
SOLUTION · Connect the input (or output) cables. · Check connections by referring to <Protection function>. · Replace the fuse and use lower volume. · After check the speaker cord and fixing the cause of the short,
replace the fuse. · Adjust the control correctly referring to <Controls>.
· Connect them properly checking the + / - of the terminals and wires well.
· Connect the speaker wire again so that it is not pinched by anything.
· Set switches properly by referring to <Controls>. · Connect the Remote Cable securely and correctly.
Specifications .ua Specifications subject to change without notice.
CEA-2006
RMS Watts per channel @ 4 ohms, 1 % THD+N .......................................................................................................................................................................600 W × 1 Signal to Noise Ratio (Reference: 1Watt into 4 ohms) ................................................................................................................................................................ 80 dBA
m Audio Section o Max Power Output.........................................................................................................................................................................................................................................2400 W
Rated Power Output (+B = 12.0 V) (4 ) (20 Hz 200 Hz, 0.5 % THD).....................................................................................................................................................................................400 W × 1
.c (2 ) (100 Hz, 0.5 % THD).......................................................................................................................................................................................................800 W × 1
(1 ).............................................................................................................................................................................................................................................. 800 W × 1 Rated Power Output (+B = 14.4 V)
(4 ) (20 Hz 200 Hz, 0.5 % THD).....................................................................................................................................................................................600 W × 1 (4 ) (DIN45324, +B = 14.4 V) .............................................................................................................................................................................................600 W × 1
0 (2 ) (100 Hz, 0.5 % THD).................................................................................................................................................................................................... 1200 W × 1
(1 )........................................................................................................................................................................................................................................... 1000 W × 1
3 Frequency Response (+0, 3 dB)..............................................................................................................................................................................................5 Hz 400 Hz
Sensitivity (rated output) (MAX.) .................................................................................................................................................................................................................0.2 V
1 Sensitivity (rated output) (MIN.) ..................................................................................................................................................................................................................5.0 V
Input Impedance ............................................................................................................................................................................................................................................... 10 k Signal to Noise Ratio......................................................................................................................................................................................................................................105 dB Low Pass Filter Frequency (24 dB/oct.)..............................................................................................................................................................40 200 Hz (variable) Infrasonic Filter Frequency (24 dB/oct.) .............................................................................................................................................................. 15 60 Hz (variable) Band Reject Filter ...................................................................................................................................................................................................................OFF/ -6 dB/ -12 dB Band Reject Filter Frequency.................................................................................................................................................................................... 40 200 Hz (variable) Phase Inverter ...................................................................................................................................................................................................... 0° (Normal) / 180° (Reverse) Bass Boost Circuit..................................................................................................................................................................................................................0 18 dB (variable) Bass Boost Frequency....................................................................................................................................................................................................40 100 Hz (variable) Bass Boost Frequency................................................................................................................................................................................................................................................... General Operating Voltage .............................................................................................................................................................................................. 14.4 V (11 16 V allowable) Current Consumption ........................................................................................................................................................................................................................................ 75 A Installation Size (W × H × D) .........................................................................................................................................................................................340 × 60 × 225 mm
..................................................................................................................................................................................................................1213-3/8 × 2-3/8 × 8-7/8 inch Weight ................................................................................................................................................................................................................................................ 3.8 kg (8.38 lbs) Weight ..................................................................................................................................................................................................................................................................................
8 English
Autogood products Internet store "130"
Internet store http://130.com.ua