TECKNET TK-HS006 Wireless Headset User Manual
Introduction
Thank you for purchasing the TECKNET Wireless Headset. Please read this User Manual thoroughly before use and retain it for future reference. If you have any problems using this Wireless Headset, please contact us by email at support@tecknet.com.
Product Overview
The TECKNET TK-HS006 is a wireless headset. The product overview diagram shows the headset with the following labeled parts: 1. Volume +, 2. MFB (Multifunction Button), 3. Volume -, 4. LED Indicator Light, 5. On/Off Button, 6. Microphone, 7. Aux Input, 8. USB-C Charging Port, 9. Input: DC 5V/600mA, 10. Battery Capacity: 600mAh, 11. Battery Voltage: 3.7V.
Specifications
| Feature | Details |
|---|---|
| Connection | BT or Wired |
| BT Version | V5.0 |
| Supported Protocols | HFP V1.7, A2DP V1.3, AVRCP V1.6 |
| Operation Range | 10 meters |
| Standby Time | Approx. 600 hrs |
| Operating Time (Music/Call) | Approx. 36 hrs (70% volume) |
| Talk Time | Approx. 37 hrs (90% volume) |
| Charging Time | Approx. 2.5 hrs |
| Input | DC 5V/600mA |
| Battery Capacity | 600mAh |
| Battery Voltage | 3.7V |
| Operating Temperature | -10°C to 45°C |
| Charging Cable Length | 11.8 in (30 cm) |
| Audio Cable Length | 47 in (120 cm) |
Package Contents
- Wireless Headset
- 3.5mm Audio Cable *1
- USB-A to USB-C Charging Cable *1
- User Manual *1
Charging the Headset
- When the LED indicator flashes RED, please charge the headset.
- Connect the USB-C end of the charging cable to the headset and the USB-A end to a powered PC, charger, or power bank. The LED indicator lights in steady RED.
- Charging is completed in about 2.5 hours. The LED indicator turns off when the headset is fully charged.
Note: If the headset will not be used for a long haul, fully charge the battery and charge it once every 2 months.
Pairing Methods
A. BT Pairing
- Turn on Bluetooth on your phone.
- Press and hold the On/Off Button for 2 seconds. The headset will hear "Power on. Pairing", and the LED indicator will flash blue and red alternately.
- Search and tap to connect to "TK-HS006" on the Bluetooth device list of your phone. You will hear "Connected". The LED indicator will flash blue every 6 seconds after the headset is paired.
Note: The headset can also be connected to a computer via Bluetooth. Follow the same steps.
B. Wired Connection
Plug one end of the 3.5mm audio cable into the Aux Input port on the headset and the other end into that of your phone or computer. Then you can use the headset as a high-quality wired headset without powering on.
Note: When connected with the audio cable in the power-on state, the headset will shut down automatically. If you need to use BT connection, unplug the audio cable and power on the headset, then follow the "BT Pairing" steps.
To Pair with Two Phones
- Follow the above pairing guide to connect the headset to phone A, then switch off the Bluetooth function of phone A.
- At this point, the headset automatically enters pairing mode.
- Search and click to connect to "TK-HS006" on the Bluetooth device list of phone B.
- After the headset is paired with phone B, switch on the Bluetooth function of phone A and tap "TK-HS006" to reconnect to the headset.
- Now the headset is connected with two phones.
Note: When the headset is paired with two phones, music can only be played from one. If you want to play music on the other connected phone, pause or stop playing the music on the previous one. If you want to answer a call from the other connected phone, hang up the current call on the previous one.
Operations Instructions
MFB (Multifunction Button)
| Button | Function | Operation Instructions |
|---|---|---|
| On/Off Button | Power on | Press and hold the On/Off Button for 2 seconds. |
| Power off | Press and hold the On/Off Button for 3 seconds. | |
| MFB | Answer a call | Short press the MFB to answer a call. |
| Hang up a call | Short press the MFB to hang up a call. | |
| Cancel dialing | Short press the MFB to cancel dialing. | |
| Reject a call | Press and hold the MFB for 2 seconds to reject an incoming call. | |
| Play/Pause | Short press the MFB to play/pause music. | |
| Redial a call | Double press the MFB to dial the last number dialed. |
Volume/Track Control
| Button | Function | Operation Instructions |
|---|---|---|
| Volume + | Volume up | Press the Volume + button. To switch to the next track, press and hold the Volume + button for 2 seconds. |
| Volume - | Volume down | Press the Volume - button. To switch to the previous track, press and hold the Volume - button for 2 seconds. |
| Clear pair record | Press and hold Volume + and Volume - for 2 seconds to clear the pair record in the headset. When it is cleared, the headset will not be automatically connected, and you need to establish the connection. |
EQ Mode
| Button | Function | Operation Instructions |
|---|---|---|
| EQ mode | Switch EQ mode | On/Off Button to choose from: EQ mode, Bass mode, Vocal mode. |
Voice Assistant
| Button | Function | Operation Instructions |
|---|---|---|
| MFB | Activate voice assistant | Press and hold the MFB for 2 seconds to activate the voice assistant on your phone. (Only in the non-calling state) |
LED Indicator Light
| Mode | LED Indicator Light |
|---|---|
| Power on | Red & Blue light flash alternately |
| Power off | Red light turns on for 1 second |
| Pairing mode | Red & Blue light flash alternately |
| Connected | Blue light flashes once every 6 seconds |
| Disconnect | Red & Blue light flash alternately |
| Playing music | Blue light flashes once every 6 seconds |
| Talking | Blue light flashes once every 6 seconds |
| Low battery | Red light flashes slowly |
| Charging | Steady Red light |
| Fully charged | Steady Blue light |
| Delete pair record | Blue and Red LED light up for 1 second, then flash alternately |
Voice Prompt
| Status | Voice Prompt |
|---|---|
| Power on | Power on |
| Power off | Power off |
| Pairing mode | Pairing |
| Connected | Connected |
| Headset disconnected | Disconnected |
| Low battery | Low battery |
| Clear pair record | Clear matching record |
| Pop Mode | Pop Mode |
| Bass Mode | Bass Mode |
| Vocal Mode | Vocal Mode |
FAQs
Q: What should I do if the sound cuts in and out?
A: 1. Make sure to keep the headset within the effective operation range (10 meters). 2. Keep the headset away from electromagnetic interference, such as microwave ovens, base stations, etc. 3. If the headset is low, please fully charge it before use.
Q: What to do if I cannot turn the power on?
A: Check if the headset is in low battery state (red light flashes slowly). If it is, recharge the headset. Turn on the headset again after it is fully charged (steady blue light). If this does not help, you may contact our customer service for more support.
Q: What to do if I fail to pair the headset with my devices?
A: 1. Turn off the power of the headset, and then turn it back on. Pair the headset with your device again. 2. If the above methods do not help, you may contact our customer service for more support.
Q: How to reconnect?
A: 1. When the headset goes out of operation range, you will hear "Disconnected", short press the MFB to reconnect. 2. If the headset is paired with your device successfully, it will reconnect to the paired device automatically within 10 minutes every time it powers on. If the reconnection failed, please try pairing again. It will automatically reconnect after entering the operation range.
Q: Why does the headset power off automatically?
A: When the headset is not connected over 10 minutes or the battery is too low, the headset will power off automatically.
Q: How to clean the headset?
A: Use a soft cloth to wipe off dust. Do not use any detergent to clean the headset.
Q: Can I use the headset with the audio cable only but without BT function?
A: Yes, you can use it as a high-quality wired headset without powering on. When connected with the audio cable in the power-on state, the headset will shut down automatically. If you need to use BT connection, unplug the audio cable and power on the headset, then follow the "BT Pairing" steps.
Q: What devices can recharge the headset?
A: Any charger, car charger, power bank, PC, etc. with DC 5V/above 1A output.
Limited 12-Month Warranty
What this warranty covers
Shenzhen Unichain Technology Co., Ltd. (Manufacturer: "Unichain") warrants to the original purchaser of this TECKNET product that the product shall be free of defects in design, assembly, material, or workmanship.
What the period of coverage is
Unichain warrants the TECKNET product for 12 Months.
What will we do to correct problems?
Unichain will repair or replace, at its option, any defective product free of charge (except for shipping charges for the product).
What is not covered by this warranty?
All above warranties are null and void if the TECKNET product is not provided to the purchaser for inspection upon request or if Unichain determines that the TECKNET product has been improperly installed, altered in any way, or tampered with. The TECKNET Product Warranty does not protect against acts of God such as flood, earthquake, lightning, etc., nor against normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low voltage disturbances (e.g. brownouts or sags), non-authorized program, or system equipment modification or alteration.
Correct Disposal of This Product
(WEEE Directive - Electronic Equipment)
This Marking indicates that this product should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this product from other types of waste and recycle it responsibly to promote the sustainable reuse of material resources. Household user should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
IMPORTANT SAFETY INSTRUCTIONS - CAREFULLY FOLLOW THESE INSTRUCTIONS
- RETAIN THESE INSTRUCTIONS - This sheet contains important safety and operating instructions. ?
- Before using the product, read all instructions and caution markings on the product, accessories, and device. ?
- Children should be supervised to ensure that they do not play with the appliance. ????
- Keep the product away from the fire to avoid an explosion. ?
- Do not place the product or near an inflammable, explosive, or hazardous object. ? ?
- Do not operate the product with a damaged cord or plug. ?
- Do not operate the product if it has been damaged in any way. ⚠️
- Do not disassemble the product. Disassembly may result in a risk of electric shock. ?️ ⚡
- Keep the product away from heat sources. ?️
- To reduce the risk of electric shock, unplug the product from the power supply when not in use or switch off the power supply. ⚡
Product Dimensions and Material
Finished Product Size: 80 x 100mm
Material: 105g Double Copper, Single Color Printing, Double-Sided Printing, Saddle Stitching
For more information, visit the TECKNET website: https://www.tecknet.com
For warranty information, visit: https://www.tecknet.com/pages/support
