Installation Guide for SAMSUNG models including: ME4000R Range Microwave Oven, ME4000R, Range Microwave Oven
Samsung ME19R7041FT/AA Quick Guide
Samsung ME19R7041FB/AA Quick Guide
Samsung ME19R7041FG/AA Quick Guide
File Info : application/pdf, 20 Pages, 3.00MB
DocumentDocumentInstallation Instructions Over The Range Microwave Oven BEFORE YOU BEGIN (Read these instructions completely and carefully.) IMPORTANT Save these instructions for local inspector's use. IMPORTANT Observe all governing codes and ordinances. · Note to Installer - Be sure to leave these instructions with the Consumer. · Note to Consumer - Keep these instructions for future reference. · Skill level - Installation of this appliance requires basic mechanical and electrical skills. · Proper installation is the responsibility of the installer. · Product failure due to improper installation is not covered under the Warranty. READ CAREFULLY. KEEP THESE INSTRUCTIONS. ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 1 2021-03-25 11:43:17 Contents General information Important safety instructions . . . . . . . . . . . 3 Electrical requirements. . . . . . . . . . . . . . . . 3 Hood exhaust . . . . . . . . . . . . . . . . . . . . . . . . 4 Damage - Shipment/Installation . . . . . . . . 6 Parts included . . . . . . . . . . . . . . . . . . . . . . . 6 Tools you will need . . . . . . . . . . . . . . . . . . . 7 Mounting space . . . . . . . . . . . . . . . . . . . . . . 7 Step-by-step installation guide 1. Placement of the mounting plate. . . . . . 8 A. Removing the microwave oven from the carton/Removing the mounting plate. . . . 8 B. Finding the wall studs . . . . . . . . . . . . . . . . 8 C. Determining wall plate location under your cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 D. Aligning the wall plate . . . . . . . . . . . . . . . 10 2. Ventilation types (choose a, b or c) . . . 11 A. Outside top exhaust (vertical duct) . . . . 12 A1. Installation procedure for the exhaust adaptor and proper damper operation check . . . . . . . . . . . . . . . . . . . . . . . . . . 12 A2. Adjust the exhaust adaptor . . . . . . . . 12 B. Recirculating (non-vented ductless). . . . 12 B1. Adapting the microwave blower for recirculation . . . . . . . . . . . . . . . . . . . . . 12 B2. Installing the charcoal filter. . . . . . . . . 13 C. Outside back exhaust (horizontal duct) . 14 C1. Adapting the microwave blower for outside back exhaust . . . . . . . . . . . . . 14 3. Installation . . . . . . . . . . . . . . . . . . . . . . . 15 A. Preparing the rear wall for outside back exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . 15 B. Attach the mounting plate to the wall . . 15 C. Use the top cabinet template to prepare the cabinet above . . . . . . . . . . . . . . . . . . 16 D. Mount the microwave oven . . . . . . . . . . 16 E. Connect the ductwork for outside top exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4. Before you use your microwave . . . . . 18 2 ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 2 2021-03-25 11:43:17 General information IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to ensure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies. CAUTION: For personal safety, remove the house fuse or open the circuit breaker before beginning the installation to avoid severe or fatal shock injury. CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load in addition to the added weight of this 69 pound product, plus additional oven loads of up to 50 pounds or a total weight of 109 pounds. CAUTION: For personal safety, do not install this product in cabinetry configured as an island or a peninsula. The microwave oven must be mounted to BOTH a top cabinet AND a wall. NOTE: For easier installation and personal safety, we recommend that two people install this pIrnosudreucprto.per groundexists IMbePfoOreRusTeANT PLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK. InsurIgenrsopuurrneodpperexoiprsetsr grounbedfoerexuisstes before use. The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance. You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded. If you have a standard two-prong wall receptacle, it is very important to have it replaced with a properly grounded three-prong wall receptacle, installed by a qualified electrician. DO NOT, UNDER ANY CIRCUMSTANCES, CUT, DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD. ELECTRICAL REQUIREMENTS Product rating is 120 volts AC, 60 Hertz, 14.5 amps and 1.7 kilowatts.This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a separate branch circuit single grounded outlet of at least 15 A and max of 20 A. The outlet box should be located in the cabinet above the microwave oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code. 3 ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 3 2021-03-25 11:43:17 General information HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 11. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart contains an example of one possible ductwork installation. DUCT PIECES EQUIVALENT LENGTH x NUMBER USED = EQUIVALENT LENGTH Roof Cap 24 ft. x (1) = 24 ft. 12 Ft. Straight Duct (6 Round) 12 ft. x (1) = 12 ft. Rectangular-to-Round Transition Adaptor* 5 ft. x (1) = 5 ft. Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood. Total Length = 41 ft. * IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper. OUTSIDE BACK EXHAUST (EXAMPLE ONLY) The following chart contains an example of one possible ductwork installation. DUCT PIECES EQUIVALENT LENGTH x NUMBER USED = EQUIVALENT LENGTH Wall Cap 40 ft. x (1) = 40 ft. 3 Ft. Straight Duct (3 ¼ x 10 Rectangular) 3 ft. x (1) = 3 ft. 90 ° Elbow 10 ft. x (2) = 20 ft. Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood. Total Length = 63 ft. NOTE: For back exhaust, care should be taken to align the exhaust with the space between studs, or the wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust. 4 ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 4 2021-03-25 11:43:17 General information NOTE: If you need to install ducts, note that the total duct length of 3 ¼ x 10 rectangular or 6 diameter round duct should not exceed 140 equivalent feet. Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully. NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure dampers swing freely and nothing is blocking the ducts. Exhaust connection: The hood exhaust has been designed to mate with a standard 3 ¼ x 10 rectangular duct. If a round duct is required, a rectangular-to-round transition adaptor must be used. Do not use less than a 6 diameter duct. Maximum duct length: For satisfactory air movement, the total duct length of 3 ¼ x 10 rectangular or 6 diameter round duct should not exceed 140 equivalent feet. Elbows, transitions, wall and roof caps, etc., present additional resistance to airflow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total duct length, add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections. The chart below shows you how to calculate total equivalent ductwork length using the equivalent length in feet of some typical ducts. DUCT PIECES EQUIVALENT LENGTH x NUMBER USED = EQUIVALENT LENGTH Rectangular-to-Round Transition Adaptor* 5 ft. x ( ) = ft. Wall Cap 40 ft. x ( ) = ft. 90 ° Elbow 10 ft. x ( ) = ft. 45 ° Elbow 5 ft. x ( ) = ft. 90 ° Elbow 25 ft. x ( ) = ft. 45 ° Elbow 5 ft. x ( ) = ft. Roof Cap 24 ft. x ( ) = ft. Straight Duct 6 Round or 3 ¼ x 10 Rectangular 1 ft. x * IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using tin snips, to allow free movement of the damper. ( ) = ft. Total Ductwork = ft. Equivalent lengths of duct pieces are based on actual tests and reflect the requirements for good venting performance with any vent hood. 5 ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 5 2021-03-25 11:43:18 General information DAMAGE - SHIPMENT/INSTALLATION · If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. · If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. · If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between the customer and installer. PARTS INCLUDED HARDWARE PACKET PART QUANTITY Wood Screws (¼ x 2) 1 Toggle Bolts (and wing nuts) 2 (3/16 x 3) Self-aligning Machine Screws (¼ - 28 x 3 ¼) 2 ADDITIONAL PARTS TOP CABINET TEMPLATE PART Top Cabinet Template QUANTITY 1 REAR WALL TEMPLATE Rear Wall Template 1 Installation Instructions 1 You will find the installation hardware contained in a packet with the unit. Check to make sure you have all these parts. NOTE: Some extra parts are included. Separately Packed Grease Filters 2 Exhaust adaptor 1 6 ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 6 2021-03-25 11:43:18 TOOLS YOU WILL NEED General information #1 and #2 Phillips screwdriver Pencil Ruler or tape measure and Carpenter square (optional) straight edge Tin snips (for cutting damper, if required) Scissors (to cut template, if necessary) Electric drill with 3/16, ½ and drill bits Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Gloves Saw (saber, hole or keyhole) Stud finder or Hammer (optional) Safety goggles Level Duct and masking tape MOUNTING SPACE 12 max. 16 ¹ 30 5 30 min. Bottom edge of the cabinet needs to be 30 or more from the cooking surface. Backsplash NOTES: · The space between the cabinets must be 30 wide and free of obstructions. · This microwave oven is for installation over ranges up to 36 wide. · If you are going to vent your microwave oven to the outside, see the Hood Exhaust Section for exhaust duct preparation. · If installing the microwave oven beneath smooth flat cabinets, be careful to follow the instructions on the top cabinet template for power cord clearance. · Maximum cabinet depth above and beside the unit is 12. · The dimensions provided are the minimum required for mounting the microwave oven. Local codes and the practical use of the range will likely require you to provide more than the 13.5 shown between the range and the bottom of the microwave. 7 ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 7 2021-03-25 11:43:18 Step-by-step installation guide 1. PLACEMENT OF THE MOUNTING PLATE A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/REMOVING THE MOUNTING PLATE 1. Remove the installation instructions, Exhaust adaptor, filters, glass tray, and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven. 2. Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam. CCaarrtotnon StyroSftoyraofmoam 3. Pull the carton up and off the oven. 4. Remove and properly discard plastic bags. Screws Screws Mounting Plate B. FINDING THE WALL STUDS WWaallllSStuuddss CeCnetnetrer 1. Find the studs using one of the following methods: A. With a stud finder a magnetic device which locates nails. OR B. Use a hammer to tap lightly across the mounting surface until you hear a solid sound. This will indicate a stud location. 2. After locating the stud(s), locate the stud's center by probing the wall with a small nail to find the edges of the stud. Then, place a mark halfway between the edges. The center of any adjacent studs should be 16 or 24 from this mark. 3. Draw a line down the center of the studs. THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD. 5. Remove the 2 screws from the mounting plate. This plate will be used as the rear wall template and for mounting. NOTE: Retain the two screws. You will need to re-insert the screws in their original locations after you have removed the mounting plate. 8 ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 8 2021-03-25 11:43:18 Step-by-step installation guide C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position beneath a flat bottom cabinet. Plate position beneath a framed recessed cabinet bottom. 16 ¹ C L At least 30 Draw a vertical line on the wall at the center of the 30 wide space. Tape the Rear Wall Template onto the wall so that the top of the template touches the bottom of the cabinet and the centerline on the template lines up with the line you drew on the wall. Plate position beneath a recessed bottom cabinet with a front overhang. Draw a horizontal liDneratwo amlainrek ohnowthefar tbhaeciknswidaell eoqf uthael tofrothnet odveeprthhaonfgthdeesfrcoennt ds boevleorwhatnhge. cabinet. C L 30 to Cooktop Draw a vertical line on the wall at the center of the 30 wide space. Tape the Rear Wall Template onto the wall so that the top of the template touches the bottom of the cabinet frame and the centerline on the template lines up with the line you drew on the wall. Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level. THE MICROWAVE MUST BE LEVEL. Use a level to make sure the cabinet bottom is level. `i 3300" ttoo CCooookktotopp Draw a vertical line on the wall at the center of the 30 wide space. Draw a second, horizontal line on the wall below the cabinet to mark how far the inside of the front overhang descends below the cabinet. Tape the Rear Wall Template onto the wall so that the top of the template touches the bottom of the horizontal line and the centerline on the template lines up with the vertical line. 9 ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 9 2021-03-25 11:43:19 Step-by-step installation guide D. ALIGNING THE WALL PLATE HHolleeAA CeCnetneterrlliinnee nontoctchheess Draw a vertical line oDnratwhea Vweartlilctaol Lminaerk tohneWcaelnl ftreomr oCfetnhter coaf TboinpeCtaabbinoevte. HHoorirzizoonntatallLLininee AArereaaEE CL HHoollee BB HHoorriizzoonnttaallLLiinnee DDrraawwaahHoroizrioznotnatlallinlieneononthwe awllafllroamlong tbhoettboomttoomf "oRf ethaer "WRaeallrTWemallpTlaetme"p.late". CAUTION: Wear gloves to avoid cutting fingers on sharp edges. 1. Draw a horizontal line on the wall at the bottom of the "Rear Wall Template". 2. Drill holes for toggle bolts in 3 locations (Hole A, Hole B, Hole C) as shown in the illustration above. If the location of a hole lines up with a stud, drill a 3/16 hole for a wood screw. You cannot use a toggle bolt to attach the wall plate to a stud. NOTE: DO NOT MOUNT THE PLATE AT THIS TIME. 3. Holes A, B and C are inside area E. If none of these holes line up with a stud, find a stud in area E that lines up with a hole circle in Area E, and then drill a 3/16 hole into it for a wood screw. You must have at least one wood screw mounted firmly into a stud to support the weight of the microwave. Set the mounting plate aside. ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 10 10 2021-03-25 11:43:19 Step-by-step installation guide 2. VENTILATION TYPES (CHOOSE A, B OR C) This microwave oven is compatible with the following three types of ventilation: A. Outside Top Exhaust (Vertical Duct) B. Recirculating (Non-Vented Ductless) C. Outside Back Exhaust (Horizontal Duct) NOTE: This microwave is shipped assembled for Outside Top Exhaust (except for non-vented models). An exhaust adaptor is shipped assembled and attached to the fillerupper. Select the type of ventilation required for your installation and proceed to that section. A. OUTSIDE TOP EXHAUST (VERTICAL DUCT) AfAfoodrdarOapOutpotsrutidoitnesrPiidlanceePTloapce EToxphEaxhuasutst B. RECIRCULATING (NON-VENTED DUCTLESS) See page 12 See page 12, Part B IMPORTANT: You must install the included Charcoal Filter if you select nonvented exhaust. The charcoal filter is provided with the unit. C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT) See page 14 ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 11 11 2021-03-25 11:43:19 Step-by-step installation guide A. OUTSIDE TOP EXHAUST (VERTICAL DUCT) A1. INSTALLATION PROCEDURE FOR THE EXHAUST ADAPTOR AND PROPER DAMPER OPERATION CHECK Damper NOTE: You must attach the house duct to the exhaust adaptor after installation is complete. HoHuosuseeDDuucct t Blower Plate Exhaust Adaptor Back of Retaining Hooks Microwave Oven 1. Slide the exhaust adaptor into place as shown in the diagram above. 2. Make sure the tape securing the damper is removed and damper pivots easily before you mount the microwave. CAUTION: You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed. A2. ADJUST THE EXHAUST ADAPTOR After you have installed the microwave, you will need to open the top cabinet and adjust the exhaust adaptor so that you can connect it to the house duct. Damper Back of Microwave Oven For Side-toSide Adjustment, Slide the Exhaust Adaptor as Needed B. RECIRCULATING (NON-VENTED DUCTLESS) B1. ADAPTING THE MICROWAVE BLOWER FOR RECIRCULATION 1. Remove and save screw that holds blower plate to microwave. 2. Lift up the blower plate. Blower Retaining Screws Back of Microwave Oven NOTE: The exhaust adaptor with the damper is not needed for recirculating models. You may want to save them for possible future use. ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 12 12 2021-03-25 11:43:19 Step-by-step installation guide 3. Remove the screw that holds the blower motor and carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. 7. Close the blower door. Slide blower shield onto the top of the blower door opening. CAUTION: To avoid breaking or cracking the blower blade, do not touch the blade. Hold the outer case of the blower when you pull it out or put it back in place. 4. Roll the blower unit 90 ° so that the fan blade openings are facing toward the front of the microwave. Before Roll After Roll 8. Secure the blower to the microwave using the blower retaining screws from Step 1. Blower Retaining Screw Blower Retaining Screws 5. Place the blower unit back into the opening. CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. 6. Remove the metal vent fan cover on the back of the microwave by sliding it up. Back of Microwave Oven B2. INSTALLING THE CHARCOAL FILTER 1. Remove the screws on the top of the grille using a #1 Phillips screwdriver. 2. Open the door. 3. Remove the grille. · Push the grille left, and then pull the grille straight off. Charcoal filter 4. Install the charocal filter. When properly installed, the wire mesh of the filter should be visible from the front. 5. Reinstall the grille and the screws. 6. Close the door. Insert mesh-side up ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 13 13 2021-03-25 11:43:20 Step-by-step installation guide C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT) C1. ADAPTING THE MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST 1. Remove and save screw that holds blower Plate to microwave. Blower Retaining Screws Back of Microwave Oven 2. Open the blower door by lifting it up at the back of the microwave. Remove and save the blower shield on the back of the microwave by sliding it up. Remove and save the metal vent fan cover on the back of the microwave by sliding it up. 3. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. BEFORE: Fan Blade Openings Facing Forward End B End A CAUTION: To avoid breaking or cracking the blower blade, do not touch the blade. Hold the outer case of the blower when you pull it out or put it back in place. 4. Remove Parts "A" with tin snips or pliers. Parts "A" 5. Rotate the blower unit counterclockwise 180 °. Before Rotation After Rotation Back of Microwave Back of Microwave 6. Place the blower unit back into the opening. AFTER: Fan Blade Openings Facing Back End A End B CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. NOTE: The blower unit exhaust openings should match the exhaust openings on the rear of the microwave oven. 7. Close the blower door. Slide blower shield onto the top of the blower door opening. Secure the blower to the microwave oven using the blower retaining screws from Step 1 except the upper blower motor retaining screw. Blower Retaining Screw Blower Shield Blower Retaining Screw Back of Microwave Oven 8. Slide the exhaust adaptor onto the back of the microwave oven, securing it into the lower locking tabs. Take care to ensure that the damper hinge is installed so that it is at the top and that the damper swings freely. Reinstall the upper blower motor screw through the adaptor and the blower door and into the back of the microwave oven. Back of Microwave Oven Guide Adaptor Guide Locking Tabs (not shown) Blower Motor Door Retaining Screw ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 14 14 2021-03-25 11:43:20 3. INSTALLATION Step-by-step installation guide INSTALLATION OVERVIEW A. Prepare the Rear Wall (for outside back exhaust/ horizontal duct only) B. Attach the Mounting Plate to the Wall C. Prepare the Cabinet above D. Mount the Microwave Oven E. Connect the Ductwork (for outside top exhaust/vertical duct only) A. PREPARE THE REAR WALL FOR OUTSIDE BACK EXHAUST You need to cut an opening in the rear wall for outside exhaust. B. ATTACH THE MOUNTING PLATE TO THE WALL CL · Read the instructions for outside back exhaust on the REAR WALL TEMPLATE. · Tape the REAR WALL TEMPLATE to the rear wall. · Cut the opening, following the instructions on the REAR WALL TEMPLATE. CAUTION: Do not cut an opening in the rear wall if you are installing the microwave with vertical duct or nonvented ductless ventilation. Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. 1. Remove the toggle wings from the bolts. 2. Insert the bolts into the mounting plate through the holes designated to go into drywall, and then reattach the toggle wings so that ¾ of the bolt protrudes beyond the wing. ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 15 15 2021-03-25 11:43:21 Step-by-step installation guide To use toggle bolts: MoMuonutnintingg PlaPtelate Spacing for Toggles More Than Wall Thickness TooggggleleWWinignsgs TTooggggllee BBooltt D. MOUNT THE MICROWAVE OVEN WWalll BBoolltt Enndd 3. Place the mounting plate against the wall, pinch the wings of each toggle together, and then insert the toggle wings of each toggle into and through the holes in the wall. NOTE: Before tightening the toggle bolts and wood screw, make sure the bottom of the Mounting plate runs along the bottom Horizontal line of the "Rear wall Template" and the Mounting plate is properly centered under the cabinet. CAUTION: Be careful to avoid pinching your fingers between the back of the mounting plate and the wall. 4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts. Tighten the screw. C. USE THE TOP CABINET TEMPLATE TO PREPARE THE CABINET ABOVE You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip the handle or use the handle during installation to support the microwave. NOTE: If your cabinet is metal, use the nylon grommet in the power cord hole to prevent the cord from being cut. NOTE: Filler blocks are required when mounting this unit under any cabinet with a recessed bottom or front overhang. (See page 9.) IMPORTANT: The case damage that will occur from over tightening screws if you do not use filler blocks is not covered under warranty. NOTE: When mounting the microwave oven, thread the power cord through hole in the bottom of the top cabinet. Keep it tight throughout Steps 13. Do not pinch the cord or lift the oven by pulling cord. 1. Lift the microwave, tilt it forward, and hook the slots at the back bottom edge onto the four lower tabs of the mounting plate. · Read the instructions on the TOP CABINET TEMPLATE. · Tape it underneath the top cabinet. · Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. 2. Rotate the front of the oven up against the cabinet bottom. ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 16 16 2021-03-25 11:43:21 Step-by-step installation guide 3. Insert a self-aligning screw through the top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep the power cord tight. Be careful not to pinch the cord, especially when mounting flush to the bottom of the cabinet. CaCbabiinneettFFrornot nt CCaabbinienteBtotBtoomtStohemlf Shelf FFiillleerrBlBoclkock EEqquuivaivleanltetont to DDeeppthtohf of Cabinet CRaebcineetsRsecess SSeelf-lAf-liAgnliinggnSicnregwScrew MicMricorowwaavveeOOvevneTonp Top 4. Attach the microwave oven to the top cabinet. 5. Insert the 2 self-aligning screws through the cabinet bottom and, if used, through the filler blocks into the outer top of the unit. (See the illustration above). Continue to support the unit until both screws are inserted and engaged at least two full turns, then fully tighten both screws until the unit is secure. E. CONNECT THE DUCTWORK FOR OUTSIDE TOP EXHAUST HoHuousseeDDuuctct 1. Extend the house duct down to connect to the exhaust adaptor. 2. Seal the exhaust duct joints using duct tape. 6. Install the grease filters. See the Owner's Manual packed with the microwave for instructions. NOTE: For models with installed grease filters, you do not need to install a filter ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 17 17 2021-03-25 11:43:21 Before You Use Your Microwave 4. BEFORE YOU USE YOUR MICROWAVE 1. Make sure the microwave oven has been installed according to instructions. 6. Read the Owner's Manual. 2. Remove all packing material from the microwave oven. 3. Install the turntable and ring in the cavity. 4. Replace the house fuse or turn the breaker back on. 7. Keep installation instructions for the local inspector's use. 5. Plug the power cord into a dedicated 15 amp electrical outlet. IgbnreIsnofusouurrnereedIgbnpreuspoefurousrxorroneeedipps.pueeetrsrxoseripsetsr groundexists beforeuse ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 18 18 2021-03-25 11:43:21 Note ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 19 19 2021-03-25 11:43:21 ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 20 DE68-04585A-01 2021-03-25 11:43:21Adobe PDF Library 15.0 Adobe InDesign 16.1 (Windows)
