Ufree U-1257 Professional Hair Clipper

Product Overview

The Ufree U-1257 is a professional hair clipper designed for precise haircuts and grooming. It features a sharp stainless steel blade, a high-performance motor, and a rechargeable lithium-ion battery.

Dimensions: 78mm width, 103mm height.

Components:

• Sharp Stainless Steel Blade
• Cutter Cleaning Brush
• Limit Combs (4 lengths: 1.2, 3, 4mm)
• Taper Lever
• ON/OFF Switch
• High-performance Battery (1200mA Li-ion)
• Specific Adapter (Input: 100-240V~50/60Hz, Output: 5V 1000mA)

Specifications

Clipper Parameters:

• Operating Voltage: 5V
• Axis Material: Wearable Brass
• Battery: 1200mA Lithium Battery
• Charging Time: About 2.5 Hours
• Operable Time in Full-power: About 3 Hours

Adapter Specifications:

• Input: 100-240V~50/60Hz
• Output: 5V 1000mA

Usage Instructions

Rechargeable Mode:

1. Insert the charger into the tail of the clipper and connect to the power to start charging.
2. The indicator light will illuminate, signifying charging has begun. A "100" indication means the battery is fully charged.
3. Both corded and cordless operation are available.

Fixed-length Function (Limit Combs):

Used for controlling hair length during haircuts and trims. Available lengths: 1.5, 3, 4.5, 6, 10, 13 mm.

1. Determine the desired haircut length.
2. Select the appropriate limit comb.
3. Mounting the limit comb: Align the comb with the blade edge and push forward slightly to mount it.
4. Disassembling the limit comb: Pull the comb firmly away from the blade.
5. Fine-tuning the cutter: Adjust the cutter by rotating the adjusting ring from forward to downward.

Taper Lever:

The taper lever adjusts the closeness of the cut. In the uppermost position, it provides the closest cut. Pushing the lever down gradually increases the cutting length.

Blade Installation and Removal

Blade Removal:

Use a screwdriver to remove the cutter head by turning the rotary cutter head underpart. Use another hand to hold the cutter to prevent it from falling.

Blade Installation:

Align the blade spring with the spring on the knife head. Insert two fixing screws and hold down. Tighten the screws with a screwdriver to ensure the blade head does not fall off.

Blade Alignment:

Ensure the blades are correctly aligned after removal or replacement. The end of the top blade teeth should be approximately 0.5mm-1.0mm back from the bottom blade. The extreme left tooth of the top blade must cover or be to the left of the first small tooth of the bottom blade. The extreme right tooth of the top blade must touch the big tooth on the bottom blade. If alignment is incorrect, add a few drops of oil, turn the clipper on briefly, turn off, unplug, loosen screws slightly, adjust, and then retighten.

Cutter Cleaning and Maintenance

Cleaning:

Clear the blade with the cleaning brush. The clipper itself cannot be washed with water. Use a slightly damp cloth or a neutral liquid soap solution for cleaning.

Maintenance:

To maintain peak condition, oil the blades every few haircuts. Hold the unit with blades in a downward position and apply 2-3 drops of oil across the top blade while the clipper is running.

Precautions for Use

• Do not disassemble the product. ❌
• Keep the hair clipper away from wet conditions. It cannot be washed with water. ?
• Clean the product only with a cloth dampened with a little water or mild soap solution. ?
• Do not charge the product in environments above 40°C or below 0°C. ?️
• Slight heating during operation or charging is normal. ?
• When the battery life expires, dispose of the battery safely at a designated recycling site. Do not discard it randomly. ♻️