YOLINK YS7906-UC Water Leak Sensor User Guide

User Guide for YOLINK models including: YS7906-UC, YS7906-UC Water Leak Sensor, Water Leak Sensor, Leak Sensor, Sensor

YS7906-UC instruction

User manual

YoSmart Inc. 7906 2ATM77906 2ATM77906 7906

File Info : application/pdf, 42 Pages, 3.21MB

✖

PDF GetApplicationAttachment.html?id=6762930

Water Leak Sensor 4
YS7906-UC
Installation & User Guide Revision Jun. 07, 2023

Contents

A . Welcome!

B . Before You Begin

C . In the Box

D . Get to Know Your Water Leak Sensor 4 03

E . Power Up

F . Install the App

G . Add Your Fob to the App

H . What Can I Do With My WL Sensor 4

I . Install the Water Leak Sensor 4

J . Introduction to WLS 4 App Settings

K . WLS 4 Settings: Device Control

L . WLS 4 Settings: Home Assistant

M . WLS 4 Settings: Scenes

N . WLS 4 Settings: Alarm Strategies

P . WLS 4Settings: Alexa

Q . WLS 4 Settings: IFTTT

R . Control-D2D Device-to-Device Pairing 25

S . Unpairing

T . Battery Replacement

V . Factory Reset

W . Firmware Updates

X . Troubleshooting

Y . Warnings

Z . Warranty

AA. FCC Statement

AB. Contact Us

A Welcome!
Thank you for purchasing YoLink products! We appreciate you trusting YoLink for your smart home & automation needs. Your 100% satisfaction is our goal. If you experience any problems with your installation, with our products or if you have any questions that this manual does not answer, please contact us right away. See the Contact Us section for more info. Thank you! Eric Vanzo Customer Experience Manager
User Guide Conventions The following icons are used in this guide to
Very important information (can save you time!) Good to know info but may not apply to you
01

B Before You Begin
Visit our Water Leak Sensor 4 support page on our website, for the latest installation guides, additional resources, information and videos by visiting: www.shop.yosmart.com/pages/water-leaksensor-4-product-support Or by scanning the QR code:
Download the most current version of the user guide by scanning the QR code:
Your Water Leak Sensor 4 connects to the internet via a YoLink hub (SpeakerHub or the original YoLink Hub), and it does not connect directly to your WiFi or local network. In order for remote access to the device from the app, and for full functionality, a hub is required. This guide assumes the YoLink app has been installed on your smartphone, and a YoLink hub is installed and online (or your location, apartment, condo, etcetera, is already served by a YoLink wireless network).
02

C In the Box

Quick Start Guide

Water Leak Sensor 4

AAA Batteries (2) Installed

Get to Know Your Water Leak Sensor 4

Alert LED Probe Sounder

Probe Status LED

SET Button

Get to Know Your Water Leak D Sensor 4, Continued

LED & Beep Behaviors
Blinking Red Once, then Green Once Device Start-Up
Blinking Red And Green Alternately Restoring to Factory Defaults
Blinking Green Connecting to Cloud
Slow Blinking Green Updating
Alert LED
Blinking Red Every 5 Seconds Leak or Flooding Warning

Fast Blinking Green Control-D2D Pairing in Progress
Blinking Red Once Device is connected to the cloud and is functioning normally
Fast Blinking Red Control-D2D Unpairing in Progress
Fast Blinking Red Every 30 Seconds Batteries are Low; Please Replace the Batteries

E Power Up

Before you can use your Water Leak Sensor 4, it must be turned on. (Batteries have been pre-installed.) Press the SET button briefly, until the LED flashes red then green (which indicates it has turned on and connected to a hub and the cloud).

F Install the App
If you are new to YoLink, please install the app on your phone or tablet, if you have not already. Otherwise, please proceed to the next section.
"YoLink app" on the appropriate app store.

Apple phone/tablet iOS 9.0 or higher

Android phone/tablet 4.4 or higher

Open the app and tap Sign up for an account. You will be required to provide a username and a password. Follow the instructions, to set up a

prompted.

You will immediately receive a welcome email from no-reply@yosmart.com with some helpful information. Please mark the yosmart.com domain as safe, to ensure you receive important messages in the future.

The app opens to the Favorite screen. This is where your favorite devices and scenes will be shown. You can organize your devices by room, in the Rooms screen, later.
05

Add Your Water Leak Sensor 4 G to the App
1. Tap Add Device (if shown) or tap the scanner icon:
Scanner icon
2. Approve access to your phone's camera, if app.
3. Hold the phone over the QR code so that the Add Device screen will be displayed.
06

Add Your Water Leak Sensor 4 G to the App, Continued
4. You can change the device name and assign it to a room later. Tap Bind device. 5. If successful, the screen will appear as shown. Tap Done.
07

What Can I Do With My Water H Leak Sensor 4
Before you begin using your Water Leak Sensor 4, and to get the most out of your purchase, you should be familiar with how the Water Leak Sensor 4's programmable buttons work, and what your Water Leak Sensor 4 can do. The Water Leak Sensor 4 has four programmable, customizable ("flexible") buttons. You operate the buttons by either a short press or a long press, each of which can result in a different response or action. The response/action depends on the programming settings of the button, of course.
to as "behaviors", (like controlling a YoLink device or scene), the Water Leak Sensor 4 can also be used with third-party applications, including Alexa routines, IFTTT applets, and with Home Assistant (like controlling a Lutron brand light switch or a Roomba robot vacuum cleaner). Please note: the button functions available to these third-party applications are in addition to
press of button 1 might control a YoLink smart plug as well as activate an IFTTT routine). For more information on using your Water Leak Sensor 4 with one or more of these third-party applications, refer to page 27.
08

What Can I Do With My Water H Leak Sensor 4, Continued
Place the Water Leak Sensor where a leak or flooding may occur Suggested Additional Applications : Basement Floors Under Laundry Machines Under Dishwashers Under Refrigerators (w/Ice Machines) Near Sump Pumps Under Fish Tanks/Aquariums Inside Hot Tubs* Locations Subject to Freezing Pipes*
Please refer to device environmental operating range information on page 21. Use this device outside the recommended ranges at your own risk
09

I Install the Water Leak Sensor 4
Sensor location considerations:
Before placing and setting up your Water Leak Sensor 4, consider the following important factors:
1. The Water Leak Sensor 4 is intended for indoor use, only. It should only be used in indoor environments and within the temperature and
listing and product support page on our website.
2. While the Water Leak Sensor 4 is waterproof, it should not be used where it will always be in water or where it may frequently be submerged in water. If water level monitoring is required, consider our Water Level Monitoring Sensor.
3. The Water Leak Sensor 4 has water-sensitive probes or electrodes on both the top and bottom. When water is on or touches any pair of electrodes, this creates an electrical "short circuit" between the electrodes, and the sensor responds with a water leak alert. The top of the
pair of electrodes. This cupped area is ideal for catching dripping water from above, such as under a sink. The bottom of the sensor has two pairs of electrodes. These are optimized for detecting water that pools or floods below the sensor. (See the next section)
10

Install the Water Leak Sensor 4, I Continued

Water Leak Sensor 4

Probe

Water detected (Water depth >0.01 inch)

Floor

4. Applications for the Water Leak Sensor 4 are many, and they can not be covered in detail in this quick start guide. If you are unsure where to place your Water Leak Sensor 4, please contact us.
5. When determining the location and quantity of sensors required for your applications, consider the types of leaks or flooding that is expected. For example is the water coming from water overflowing, like a sink, toilet, or tub? Is it coming from a leak within an appliance, like a dishwasher? Is it coming from a loose or broken
maker water line? Generally, every location where water goes into or leaves an appliance,

where water comes out, is a potential leak location.

Install the Water Leak Sensor 4, I Continued
6. Consider how water may flow and pool or collect if there is a leak at each possible leak location. Consider the slope of the floor or the surface that water may drip onto. A leak at a sink cleanout will result in water directly below the sink, and this water may run towards the front of the vanity or cabinetry or to the back, draining into the base of the cabinetry (only appearing on
Floors with drains, like in a mechanical room or near a water heater, are intentionally sloped down to the drain. Floors in older homes or where settling has occurred can also result in a slope. Take advantage of any slope in the floor by placing the leak sensor at the bottom of the slope or in the path of the water flowing down the slope. A marble, toy ball, or similar object can be used to check the floor's level, or you may consider pouring a small amount of water on the floor or surface where a leak is possible, to see how the water may flow and pool up.
7. Additional leak sensors can be added if you wish to protect a large region, or you can consider the Water Leak Sensor 2, our rope style leak sensor, that allows for creating larger water detection regions, with the use of additional cables.
8. Avoid locations where the sensor may be moved or disturbed by people or pets. Avoid
or stepped on, etc.
12

Install the Water Leak Sensor 4, I Continued
Place the leak sensor After you have selected a location for the leak sensor, simply place it on the floor or surface, with the cupped part of the sensor facing up.
Test the leak sensor Functionally test each sensor. A common way to test the Water Leak Sensor 4 is by touching any pair of electrodes with a damp paper towel, but bridging a pair of electrodes with your thumb or or on the floor, be sure to fully dry off the sensor after testing. With the app in hand, and the particular leak sensor in view in the app, test your Water Leak Sensor 4. After the sensor has responded properly (and sensor is shown to be "Normal" in the app.
13

Introduction to Water Leak J Sensor 4 App Settings
In the app, tap on your Water Leak Sensor 4's icon. Your fob's main screen should be similar to the one shown below.

Water Leak Sensor 4

Tap to exit this screen
Device name
Tap for contact & support resources
Tap for device Details screen
Device battery level icon
Battery Level of Water Leak Sensor - Shown red if battery level is low
Real-time Status of Water Leak Sensor : Normal or water-detected

Normal Alert Interval

History

Device Alert History Water detected and cleared events, logged with date & time
Alert Interval
after a leak or flooding warning Default is 5 minutes

Introduction to Water Leak J Sensor 4 App Settings

Tap the three dots (in the upper right corner) to open the fobs Details screen. Your fob's screen should be similar to the one shown below.

Details

Type Name Room

Water Leak Sensor 4 79 Leak Sensor

Favorite
Will show in favorite screen

History
Get device logs

Alarm Strategy
strategy when device alerts View your alarm strategies
Alert Interval
Continuous Alert Interval
State

Default
5 minutes Normal

Other Model Device EUI SN Temperature Signal Intensity Battery Firmware

YS7906-UC d88b4c010004123c B73768A9E0
77 °F Strong (-37 dBm)
0313

Delete
Remove Device From Current Account - Tap to delete the device from your YoLink account

Device Type Device Name (Tap to Edit) Room (Tap to Edit) Favorite (Red if Favorite, Tap to Edit) Device alarm history Tap to view device history Alarm duration Siren will automatically silence after this duration Alert Interval State
Model Number Device EUI (Unique) Device Serial Number Temperature Signal Intensity (From YoLink Hub) Battery Firmware Revision (Refer to page 26)
15

Water Leak Sensor 4 Settings: K Device Control
To control one or more YoLink devices, you have several options, including controlling one or more devices by assigning them to one of the buttons via app settings, by activating a scene (that might include taking an action on one or more devices), and by using Control-D2D
controlling one or more devices by assigning them to a button via app settings.
The devices you wish to control must have already been bound (added to) your app account. Decide on a button to assign to controlling the device or devices. You can also decide to use one button to turn the device(s) on, and another button to turn them off, or you can use the click (short-press) action to turn them on and the long-press action to turn them off (or

1. In the app, after deciding on the button to use for the on or off action, open the fob's main screen.
2. Tap Edit Fob. The fob button programming screen is displayed
3. Select the appropriate button by tapping 1, 2, 3 or 4 (on the top of the screen). The selected button will have the number underlined.
16

Water Leak Sensor 4 Settings: K Device Control, Continued
4. To use the click/short-press function of the button, tap the + button in that section. Otherwise, tap the + button in the long press section. 5. Tap Device Actions. The Choose and Set screen opens. 6. it. Depending on the device type, you will be presented with options such as Lock or Unlock, Turn ON or Turn OFF. Tap the selection that is appropriate for you. 7. Tap the check mark (upper right corner) to
8. Add additional devices and select their Choose and Set screen, tap the check mark (in the upper right corner).
17

Water Leak Sensor 4 Settings: L Home Assistant
At the time of publication of this user guide, Home Assistant support for the Water Leak Sensor 4 will be included in the next update. Refer to the Home Assistant website and the YoLink integration page for instructions. Programmers and developers are encouraged to join us on Discord. Sign up here: https://shop.yosmart.com/pages/get-connected
18

Water Leak Sensor 4 Settings: M Scenes
Before you can assign a scene to a button, you
1. In the app, from the Favorite or Rooms screen, tap the Smart button (on the bottom bar of the app). 2. The Smart screen is displayed. This screen has two parts or tabs, the Scene tab, on the left, and the Automation tab (on the right). The selected or active tab is underlined. If it is not already, tap Scene (near the top). 3. Tap the + button (upper right corner) to create a new scene. 4. Tap the Name region and follow the instructions to name your new scene. 5. You can assign an icon to the scene by tapping in the Icon region. 6. Mark this scene as a favorite by tapping on the favorite (heart) button. 7. You can leave the Group setting as-is, for now.
19

Water Leak Sensor 4 Settings: N Alarm Strategies
You can use your Water Leak Sensor 4 to enable or disable or edit an Alarm Strategy. (It is not in the scope of this user guide to cover Alarm Strategy creation and settings. Please refer to product and app support resources to familiarize yourself with Alarm Strategy settings.)
1. Open the fob's main screen. Tap the Edit Fob button. 2. Select the button for this strategy action, and tap the + button on the appropriate button behavior (click/short-press or long-press) 3. Select the Alarm Strategy option. Select your strategy, then tap either Enable Alarm, Disable Alarm or Advanced Settings. 4. Tap &RQUP to approve your selection. 5. Review your settings. Tap the Save button to save, or Cancel to exit without saving (or you can tap the Delete button, or left swipe on the behavior to delete it).
20

Water Leak Sensor 4 Settings:
O
You can actually send yourself or other account
you have a SpeakerHub, have it play an attention-getting tone, followed by it playing your message via text-to-speech. An example of needed getting out of bed. In this example, we will create a garage door status checker, that will play a message, only if the door is closed. This will demonstrate the status of a device or scene, before it proceeds to the next behavior.
1. Open the fob's main screen. Tap the Edit Fob button. 2. Select the button for this action, and tap the + button on the appropriate button behavior (click/short-press or long-press) 3. Select the Filter option. Tap Set Condition. 4. Tap Check Device. Tap Continue. 5. Select your Garage Door Sensor. Tap Closed.
21

Water Leak Sensor 4 Settings: P Alexa
You can use the Water Leak Sensor 4 to trigger Alexa routines. You must have the Alexa app installed, the YoLink skill installed and connected to your YoLink app account.
Alexa regards the Water Leak Sensor 4's four buttons as motion sensors. Only the short-press/click button behavior is recognized by Alexa (you can still use the long-press behavior for other things as Alexa ignores it) and in fact, you can still assign a YoLink app function to this button (although you are probably unlikely to need to do this). It is not in the scope of this user guide to cover set up of the Alexa skill or to cover creating an Alexa routine, so the
1. Create a new routine in the Alexa app.
2. In the When This Happens section, select Smart Home.
3. Find your Water Leak Sensor 4. Each button is
Water Leak Sensor 4's name. Select the button that you'd like to assign to this routine.
4. Tap the Detected button. Disregard the other settings available.
5. Tap Next.
22

Water Leak Sensor 4 Settings: Q IFTTT
You can use the Water Leak Sensor 4 to trigger IFTTT applets. You must have the IFTTT app installed, the YoLink service installed and connected to your YoLink app account.
Please note, IFTTT.com is a paid service, typically offering 5 free applets.
1. Create a new applet in the IFTTT app. 2. For the If This section, search and select the YoLink service. 3. Tap Flex Fob. 4. In the Device drop-down box, select your Water Leak Sensor 4, tap Done. 5. In the Button drop-down box, select the button. Tap Done. 6. In the Action drop-down box, select either Press or Long Press. Tap Done. 7. to be assigned to this button. 8. Tap Continue to save your settings.
23

Water Leak Sensor 4 Settings: Q IFTTT, Cont.
9. Review your applet settings, if they are correct tap Finish. Test your new applet by short- or long-pressing on the appropriate Water Leak Sensor 4 button.
24

Control-D2D Device-to-Device R Pairing
YoLink Control-D2D is our unique device to device control technology. Using YoLink Control-D2D, YoLink devices can be controlled without the Hub or an internet connection. (Use of YoLink Control-D2D is optional; you can use the Automation feature in the app OR use YoLink Control, but YoLink Control-D2D offers the
connection.) One device controls another, directly. A device that sends out commands is called the controller. A device that receives the commands is called the responder. Examples of a controller are a Water Leak Sensor, while examples of a responder are a Siren or the Smart Motorized Valve.
The following instructions uses pairing your Water Leak Sensor 4 with a YoLink SirenFob as example.
1. controller, Press and hold the SET button for 5-10 seconds until the LED quickly blinks green, then, release the button.
a. SET Button (5-10 seconds)
25

Control-D2D Device-to-Device R Pairing, Continued

2. the responder, close the valve using SET button or via YoLink app (verify the valve is shown to be Closed on the app).Press and hold the SET button for 5-10 seconds until the LED quickly blinks green, then, release the button.

b.Press to close the valve

c.SET Button (5-10 seconds)

3. Upon pairing, the LED will stop blinking (this may happen after only blinking two or three times).
26

Control-D2D Device-to-Device R Pairing, Continued
When the Water Leak Sensor detects water, the YoLlink Gas/Water Valve Controller will now immediately close the valve. The valve will remain closed until opened via the app or using the SET button; the restoral of the Water Leak Sensor to normal (no water detected) does not open the valve

Water Leak Sensor 4

Probe

Water detected (Water depth >0.01 inch)

Floor

More advanced sequences, controlling multiple outputs (e.g.close valve and activate siren)are available via the YoLink app

Opened

Water Pipe

Closed

S Unpairing
Please visit our website's Support page for the settings and instructions: www.yosmart.com/support-and-service
28

T Battery Replacement
Tools Required :

Small Philips Screwdriver

Tweezers

1. To maintain the watertight design of your Water Leak Sensor, use extreme care and follow the battery replacement instructions closely
2. Do not mix old and new batteries
3. Make sure that the bottom shell and sealed rubber pads are tightly secured.Otherwise, the entry of water into the sensor may cause severe damage

T Battery Replacement, Continued
1 Use tweezers to take out the four sealed rubber pads at the base of the device
2 Use a screwdriver to unscrew the screws at the base of the device and remove the base
3 Remove the two old batteries
30

T Battery Replacement, Continued
4 Install two new AAA batteries
2 × AAA
5 Close and secure the base by reinstalling and tightening the four screws
6 Reattach the four sealing rubber pads
31

U Voltage :
IP Rating : Dimensions :
Environment :

3V DC (2 - alkaline non-rechargeable AAA batteries)
IP68
2.44 × 2.44 × 0.93 inches (62 × 62 × 23.5 millimeters, L×W×D)
Working Temperature : 32°F - 122°F (0°C - 50°C) Working Humidity :
non-condensing

V Factory Reset
When directed by customer support, and/or as an attempt to resolve a problem with your fob, it may be necessary to perform a factory reset. Factory resetting your fob returns it to the factory default programming and settings. This is a simple process:
Hold the SET Button for 20 to 30 seconds, until the LED blinks red and green alternately, then release the button.
SET Button Press for 20 to 30 Seconds
Factory reset is complete when the LED stops flashing.
Pressing the button for longer than 30 seconds will abort the factory reset process. Factory reset will not remove the fob from the app. The only way to remove the fob from the app is to delete it (in the app).
33

W Firmware Updates

Your YoLink products are frequently being improved, with new features and functions added over time. It is periodically necessary to
optimal performance of your device, and to give you access to any improvements made to your
installed (added to your device) when they become available.
In the Detail screen of your device, you will see the Firmware section, as shown in the image
"#### ready now" (where #### is a four-digit combination of letters and/or numbers).

Signal Intensity Firmware

Strong (-32 dBm) 0703

Delete

Tap in the Firmware area to start the update. The fob will update automatically, indicating the progress by percentage-complete. You may use your fob during the update process, as the update is performed "in the background". You may see the LED slowly blink green during the update, and the update may continue for several minutes beyond the LED turning off.
Notice: To imporve the upgrade successrate , upgrade one device at a time instéad of mu 1tiple devices at the same time
34

W Firmware Updates, Continued
the overall operations of the fob, for example, determining when and how the fob's sounder should beep. These settings are added to the fob when it is manufactured, and they are periodically updated, as needed, to add improvements, new features, new integrations, etc, to your fob, as they become available. If you use your Water Leak Sensor 4 without an
not be made on your fob.
X Troubleshooting
If your fob does not operate as expected, if the fob has worked before, but stopped working, check and replace the batteries, if needed. If the fob has not worked before, perform the pairing process as previously explained, then test the fob again.
If this does not resolve the issue, please contact our customer support department (see the contact info on the last page of this guide).
We recommend checking for and performing any
customer support.
35

Y Warnings
For optimal performance and lifetime of your fob, please adhere to the following warnings:
The Water Leak Sensor 4 is water-resistant but not waterproof. Do not allow your fob to get wet or be submerged in water or other liquids. Promptly dry off your fob if it does get wet.
The Water Leak Sensor 4 is intended generally for use in indoor environments or safe from the elements. Do not leave your fob outside and/or where it it may be exposed to extreme hot or cold environments. The battery life can be adversely impacted by extreme hot or cold environments. The fob can be harmed by ice, water, or condensing moisture.
When replacing the batteries, only use new alkaline or lithium non-rechargeable batteries.
Do not use zinc blend batteries.
Do not mix old and new batteries.
Adhere to the battery manufacturer's safety and disposal or recycling instructions.
If storing your fob unused for extended periods, remove the batteries.
Please contact Customer Support before attempting to repair, disassemble, or modify your fob, any of which can permanently damage your fob and void the warranty.
36

Z Warranty
2 Year Limited Electrical Warranty
YoSmart Inc. warrants to the original user ("customer") of this product that it will be free from defects in materials and workmanship, under normal use, for 2 years from the date of purchase. This warranty does not apply to devices that have been improperly installed,
subjected to acts of God (such as floods, lightning, earthquakes, etc.). This warranty does not cover neglected or abused products. This warranty is limited to the repair or replacement of the device, only, at YoSmart's sole discretion YoSmart will NOT be liable for the cost of installing, removing, nor reinstalling this product, nor direct, indirect, or consequential damages to persons or property resultng from the use of this product. This warranty only covers the cost of replacement parts or replacement units, it does not cover shipping & handling fees. The customer must provide proof of purchase, in the form of the original purchase invoice or order number. The purchase must have been made from an authorized seller.
To implement this warranty please contact us by one of the methods listed on the Contact Us page of this user guide.
37

AA FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna. - Increase the separation between the
equipment and receiver. - Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected.
38

AA FCC Statement, Continued
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC's RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.
PRODUCT NAME: Water Leak Sensor 4 PARTY: YOSMART, INC. TELEPHONE: 831-292-4831 MODEL NUMBER: YS7906-UC ADDRESS: 15375 BARRANCA PKWY SUITE J-107, IRVINE, CA 92618 USA EMAIL: SERVICE@YOSMART.COM
39

AB Contact Us
We are here for you, if you ever need any assistance installing, setting up or using a YoLink app or product! Need help? For fastest service, please email us 24/7 at service@yosmart.com Or call us at 831-292-4831 (US phone support hours: Monday - Friday, 9AM to 5PM
contact us at: www.yosmart.com/support-and-service Or scan the QR code:
Support Home Page
Finally, if you have any feedback or suggestions for us, please email us at feedback@yosmart.com Thank you for trusting YoLink! Eric Vanzo Customer Experience Manager
15375 Barranca Parkway Ste. J-107 | Irvine, California 92618 © 2023 YOSMART, INC IRVINE, CALIFORNIA 40

References

Adobe PDF library 15.00 Adobe Illustrator 25.0 (Windows)