User Manual for Honeywell models including: HWB11, HD5-HWB11, HD5HWB11, HWB11AC-PRT WiFi and BT Module, WiFi and BT Module
Honeywell International Inc HWB11 HD5-HWB11 HD5HWB11 hwb11
File Info : application/pdf, 18 Pages, 1.13MB
DocumentDocumentUSER MANUAL HWB11AC-PRT, WIFI & BT Module 1Revision MODEL NO: HWB11AC-PRT ORPORATE GRAPHICS AND COMMUNICATIONS Administrative Style Sheet Guide 802.11a/b/g/n/ac + BT 5.0 System on Module Graphic Design Institute 12345 Main Street · Suite 100 Honeywell Confidential and Proprietary Table of Contents 1. Introduction ..................................................................... 1 2. Block Diagram................................................................. 3 3. Technical Specifications.................................................. 4 Recommended Operating Condition ............................................... 4 4. Footprint, Front & Back view ........................................... 5 5. Pin Configurations of Module .......................................... 6 6. Wireless Specifications ................................................... 7 WLAN.............................................................................................. 7 BLUETOOTH .................................................................................. 7 WLAN Radio Specifications ............................................................ 8 IEEE Specifications......................................................................... 8 Wi-Fi 2.4 GHz Power Table (FCC/IC) ............................................. 8 Wi-Fi 5 GHz Power Table (FCC/IC) ................................................ 9 Wi-Fi 2.4 GHz Power Table (ETSI) ................................................. 9 Wi-Fi 5 GHz Power Table (ETSI) .................................................. 10 BT & BLE 2.4GHz (ETSI & FCC/IC).............................................. 10 BLUETOOTH Radio Characteristics ............................................. 11 7. Antenna Type & Specifications ..................................... 12 8. RF Layout & Design Guidelines .................................... 14 RF Layout & Design Guidelines .................................................... 14 9. Agency Approvals ......................................................... 15 10. Labelling Guidelines for Products.................................. 16 1Chapter FCC ID: HD5-HWB11 IC: 1693B-HWB11 Model Name: HWB11AC-PRT 1. Introduction This document specifies the details for a WiFi 802.11a/b/g/n/ac with BT5.0 module called with Honeywell Part No. 50180228-001 50180227-001 RFSOM WBT, SOM MODULE, WIFI 802.11AC BT 5.0 - NA RFSOM WBT, SOM MODULE, WIFI 802.11AC BT 5.0 - ROW This HWB11AC-PRT module is a Wi-Fi/BT system on module which will be placed inside the Honeywell products like printers, barcode scanners, RFID readers etc. To enable wireless connectivity. This module includes MAC & physical layer of 802.11a/b/g/n/ac and the Bluetooth modem. This module operates on 5.0V DC Power supply with internal on-board regulation to generate 3.3v for powering ON all the circuits. The entire RF circuits is enclosed in RF shield of dimension 25mm X 25mm. The module uses internal power amplifier and LNA for 2.4GHz frequency band and an external front end chip for 5GHz frequency band. All filters and diplexers are included in the module to ensure maximum power flatness and optimum VSWR. The module has one antenna chain for 1X1 output. The module supports range of data rates from 1Mbps in 802.11b mode to MCS9 in 802.11ac mode. This chipset also supports concurrent operation of Bluetooth (Version5.0) for wireless connectivity during browsing or other device applications. Along with both standard and high speed (HS) Bluetooth data rates, Bluetooth low energy modes are also supported. Hardware WAPI acceleration engine, AES, TKIP, WPA and WPA2 are supported to provide the latest security requirement on your network. The Device communicates with HOST using SDIO interface for WIFI and UART interface for BLUETOOTH. 1 HWB11AC-PRT System on Module Features · IEEE 802.11 a/b/g/n/ac WLAN · Bluetooth 5.0 + HS · Bluetooth-WLAN coexistence · WiFi Wake on Wireless (WoW) · 20/40 MHz bandwidth at 2.4GHz · 20/40/80 MHz bandwidth at 5GHz · Internal PA/LNA · Module Size: 80 mm x 37 mm x 18mm, (LxWxH) Board · 802.11d/e/h/i/k/r · Low Current consumption in IEEE PS and Deep Sleep · WiFi Security methods: OPEN, WEP, WPA2-PSK, WPA2-1X PEAP-MSCHAPV2, PEAP-TLS, EAP-TTLS) 2 2. Block Diagram 2Chapter HWB11AC-PRT module is designed based on Qualcomm QCA6174A chipset solution. It supports generic SDIO, UART interface to connect the WLAN/BT to the host processor. A simplified block diagram of the HWB11AC-PRT module is depicted in above picture. 3 3Chapter 3. Technical Specifications Recommended Operating Condition Operating Temperature: -20° to 60°C Humidity Storage Temperature: Power Supply: I/O Voltage levels Current Consumption Max 95% (Non-condensing, relative humidity) - 30° to +70°C +5.0V DC, 0.5A 3.3v for Digital IOs, 1.8v for SDIO stream Tx output power @ 19 dBm on 11b 1M (single stream): 420mA (typ) Tx output power @ 15 dBm on 11n MCS0_HT20 (single stream-5g): 470mA (typ) 4 4. Footprint, Front & Back view 4Chapter Bottom View of HWB11AC-PRT Module Top View of HWB11AC-PRT Module 5 5. Pin Configurations of Module S No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 PINOUT GND GND BT_UART_CTS_3V3 1.8V Dig I/O PS BT_UART_RTS_3V3 BT_HOST_WAKE_3V3 BT_UART_TX_3V3 EEPROM_SDA BT_UART_RX_3V3 EEPROM_SCL BT_EN_3V3 WIFI_WAKE_ON_3V3 GND WL_EN_3V3 GND SDIO_CLK GND SDIO_D3 GND SDIO_D2 GND SDIO_D1 GND SDIO_D0 GND SDIO_CMD 5.0v DC Power Supply 5.0v DC Power Supply GND GND Signal Type Ground Ground Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Ground Input/Output Ground Input/Output Ground Input/Output Ground Input/Output Ground Input/Output Ground Input/Output Ground Input/Output 5.0v DC Power Supply 5.0v DC Power Supply Ground Ground 6 5Chapter 6Chapter 6. Wireless Specifications WLAN The HWB11AC-PRT module complies with the following features and standards. Features WLAN Standards Antenna Port Frequency Band Number of Sub Channels Modulation Supported data rates Description IEEE 802 11a/b/g/n/ac Support 1 streaming with Ant 0 (Ant1 is disabled) 2.400 GHz 2.484 GHz 4.900 GHz 5.835 GHz* 1~ 11Channels 36~ 48,52~ 64, 100~ 140, 149~ 165 Channels DSSS, CCK, OFDM, BPSK, QPSK,16QAM, 64QAM 1, 2, 5.5, 11 (Mbps) 6, 9, 12, 18, 24, 36, 48, 54 (Mbps) HT20_MCS0 ~ HT20_MCS7 VHT80_MCS0 ~ VHT80_MCS9 *Note: Band 5600 MHz to 5650 MHz is not supported for Canada BLUETOOTH The Radio specification is compliant with the Bluetooth 5.0 + EDR specification Features Frequency Band Number of Channels Modulation Description 2400 MHz ~ 2483.5 MHz 79 channels FHSS (Frequency Hopping Spread Spectrum), GFSK, DPSK Supported data rates Antenna Port BLE -1Mbps BT 1Mbps, 2Mbps, 3Mbps Single Antenna for Wi-Fi and BT 7 WLAN Radio Specifications IEEE Specifications WiFi TX EVM follow the IEEE spec that as list in the table below: Characteristics IEEE Spec RF Average Output EVM (11b) @1 Mbps 35 @11 Mbps 35 RF Average Output EVM (11a/g) @6 Mbps -5 @54 Mbps -25 RF Average Output EVM (11n) @ MCS0 -5 @ MCS7 -27 RF Average Output EVM (11ac) @ MCS0 -5 @ MCS9 -32 Wi-Fi 2.4 GHz Power Table (FCC/IC) Unit % % dB dB dB dB dB dB 8 Wi-Fi 5 GHz Power Table (FCC/IC) Note: Band 5600 MHz to 5650 MHz is not supported for Canada Wi-Fi 2.4 GHz Power Table (ETSI) 9 Wi-Fi 5 GHz Power Table (ETSI) BT & BLE 2.4GHz (ETSI & FCC/IC) 10 The HWB11AC-PRT module 2.4GHz Wi-Fi Sensitivity as list in the table below: Receiver Characteristics PER <8%, Rx Sensitivity @ 1 Mbps PER <8%, Rx Sensitivity @ 11 Mbps PER <10%, Rx Sensitivity @ 6 Mbps PER <10%, Rx Sensitivity @ 54 Mbps PER <10%, Rx Sensitivity @ MCS0_HT20 PER <10%, Rx Sensitivity @ MCS7_HT20 Typ. -97 -89 -91 -76 -91 -73 Max. -82 -76 -82 -65 -82 -64 Unit dBm dBm dBm dBm dBm dBm The HWB11AC-PRT module 5GHz Wi-Fi Sensitivity as list in the table below: Receiver Characteristics PER <10%, Rx Sensitivity @ 6 Mbps PER <10%, Rx Sensitivity @ 54 Mbps PER <10%, Rx Sensitivity @ MCS0_HT20 PER <10%, Rx Sensitivity @ MCS7_HT20 PER <10%, Rx Sensitivity @ MCS0_VHT80 PER <10%, Rx Sensitivity @ MCS7_VHT80 Typ. -94 -78 -93 -75 -87 -62 Max. -82 -65 -82 -64 -76 -51 Unit dBm dBm dBm dBm dBm dBm BLUETOOTH Radio Characteristics Parameter Basic Rate Output Power Frequency Range Sensitivity (BER) Maximum Input Level EDR Relative Power EDR Sensitivity (BER) BLE BLE Output Power BLE Sensitivity (PER) BLE Maximum Input Level Conditions Average Power BER 0.1% BER 0.1% /4-DQPSK 8DPSK /4-DQPSK BER 0.01% 8DPSK BER 0.01% Average Power PER 30.8% PER 30.8% Min. Typ. Max Unit 8 2400 -4 -4 ... ... 9 10 dBm ... 2483.5 MHz -92 -70 dBm -20 dBm 0 1.0 dBm 0 1.0 dBm -91 -70 dBm -86 -70 dBm -4 2 6 dBm ... -95 -70 dBm ... ... -10 dBm 11 7. Antenna Type & Specifications Module to be used with Antenna part no: MAF94367, Make: Laird Technologies Honeywell part no: 805-833-001 Chapter 7 12 This radio transmitter [IC:1693B-HWB11] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed above, with the maximum permissiblegain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. -- Le présent émetteur radio [IC:1693B-HWB11] a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne énumérés cidessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont trictement interdits pour l'exploitation de l'émetteur 13 8Chapter 8. RF Layout & Design Guidelines RF Layout & Design Guidelines I. Do not run antenna cables directly above or directly below the radio module. II. Do not run any high-speed digital lines below the radio. III. Use proper electro-static-discharge (ESD) procedures when installing the HWB11AC-PRT module. IV. Use non-conductive labels and to be pasted over the EMI shield provided on the module. 14 9Chapter 9. Agency Approvals FCC: Model: HWB11AC-PRT FCC ID: HD5-HWB11 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. However, there is no guarantee that interference will not occur in a installation. If this equipment does cause harmful interference to radio or reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that my cause undesired operation. Caution: MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the device. INSTALL & OPERATION: The equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 15 Industry Canada Model: HWB11AC-PRT IC: 1693B-HWB11 This device complies with Industry Canada RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Leprésent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio Exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement." Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le radiateur et votre corps. Note: Within the 5.15 to 5.25 GHz band, UNII devices will be restricted to indoor operations only. Dans la bande de 5,15 à 5,25 GHz, les appareils UNII seront restreints aux opérations intérieures. 10. Labelling Guidelines for Products The proposed FCC IC label format is to be placed on the module. If it is not visible when the module is installed into the system, "Contains FCC ID: HD5-HWB11, Contains IC:1693B-HWB11" shall be placed on the outside of final host system. Étiquetage le format proposé de l'étiquette IC de fac doit être placé sur le module.Si le module n'est pas visible lorsqu'il est installé dans le système, contenant l'ID FCC ID: HD5-HWB11, contenant l'IC: 1693BHWB11 doit être placé à l'extérieur du système hôte final. 16
