PowerLogic™ PowerTag Resi9 M63: Wireless Energy Sensor

Introduction

This document provides information on the Schneider Electric PowerLogic™ PowerTag Resi9 M63, a wireless-communication energy sensor designed for the Resi9 modular equipment range. It covers various models including R9M20, R9M21, R9M22, R9M40, R9M41, R9M42, and R9M43.

For system configuration, please refer to the concentrator's user manual. Further technical documents for Resi9 products are available on the Schneider Electric website: www.se.com.

The device complies with IEC standards including IEC 61557-12, IEC 61326-1, IEC 61010-1, and ETSI EN 300 328.

Safety Warnings

[warning] RISK OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Always disconnect all power supply sources before installing or performing maintenance on this equipment.
• Do not use a PowerTag product for voltage testing purposes; a dedicated Voltage Tester must be used.
• Failure to follow these instructions can result in death or serious injury.

[warning] FIRE HAZARD

• Use 18 mm cable ends or strip 18 mm of wire to avoid tightening against insulating material.
• Use cable ends to connect the neutral wire for the R9M20 model.
• The PowerTag must be associated with an easily accessible upstream protection and disconnection device (marked 'A' in diagrams). This device must be clearly identified and labeled.
• Cable ends for voltage measurement wires must be adapted to the product terminals. Replacement of these cable ends is the responsibility of the professional installer.
• Failure to follow these instructions can result in death, serious injury, or equipment damage.

[warning] RISK OF DAMAGING THE POWERTAG

• Comply with the neutral position.
• Disconnect the PowerTag before performing dielectric withstand tests.
• Limit insulation measurements to 500 V. The input impedance of the PowerTag between phases or between phases and neutral is 1.8 MΩ.
• Failure to follow these instructions can result in equipment damage.

Product Description and Status Indicators

The PowerTag device has the following key components:

• A: Current measurement module
• B: Product label: Features a detachable adhesive part with a unique product identifier (RF-Id) for commissioning with certain concentrators.
• C: Conductor feedthroughs: For current measurement.
• D: Safety instruction symbol: Indicates that all safety instructions associated with this symbol must be followed to avoid potential risks of injury or death.
• E: Communication status indicator light: Shows the communication status of the PowerTag.

The communication status indicator light (E) shows the following states:

• PowerTag off: No light.
• PowerTag searching for concentrator: Light flashes once every 1 second (0s ON, 1s OFF).
• PowerTag in identification mode: Light flashes once every 1 second (0s ON, 1s OFF).
• PowerTag networked. Normal communication with concentrator: Light is solid for 5 seconds, then off for 5 seconds (5s ON, 5s OFF).
• Occasional loss of communication: Light flashes once every 1 second (0s ON, 1s OFF).
• Loss of communication with concentrator: Light flashes once every 1 second (0s ON, 1s OFF).
• Internal error detected: Light flashes once every 1 second (0s ON, 1s OFF).

Installation and Connection

General Installation Guidelines:

• Ensure the concentrator has the latest software version before pairing.
• Use 18 mm cable ends or strip 18 mm of wire to avoid tightening against insulating material.
• Use cable ends for connecting the neutral wire of the R9M20.
• The PowerTag must be installed inside electrical panels or switchboards, behind a door or plate, to be inaccessible to unauthorized persons. Panels must meet applicable standards (IEC/EN 60670-24) and be installed according to current safety rules.
• Respect all relevant local, regional, and national regulations during installation and use.

Electrical Connections:

The PowerTag models connect to different electrical configurations:

• R9M20-1P: For single-phase (Un ~ 200-240 V) systems. Requires 22 AWG wire (Ø 0.33 mm²).
• R9M21-1P+N: For single-phase with neutral (Un ~ 220-240 V) systems.
• R9M22-1P+N: For single-phase with neutral (Un ~ 220-240 V) systems.
• R9M40-3P: For three-phase (Un 3~ 380-415 V) systems.
• R9M41-3P+N: For three-phase with neutral (Un 3N~ 220-240 / 380-415 V) systems.
• R9M42-3P+N: For three-phase with neutral (Un 3N~ 220-240 / 380-415 V) systems.
• R9M43-3P: For three-phase (Un 3~ 200-240 V) systems.

Connection Steps (General):

Refer to the diagrams for specific connection procedures. Ensure compliance with Resi9 ≤ 63 A requirements. Cable cross-sections and AWG equivalents are provided, for example:

• 1.5 mm² (16 AWG) for 0.7 mm wire diameter.
• 1.5-16 mm² (16-6 AWG) for wire diameters up to 18 mm.
• 1.5-2.5 mm² (16-14 AWG) for wire diameters up to 18 mm.

The diagrams illustrate the physical connection of wires to the PowerTag terminals, often involving inserting conductors into terminals and securing them.

Technical Specifications

General Specifications:

• Nominal Voltage (Un): ~ 200-240 V, 3~200-240 V, 3~380-415 V, or 3N~220-240/380-415 V.
• Operating Range (Power supply & voltage measurement): Un ± 20%.
• Frequency: 50/60 Hz.
• Maximum Power Consumption: ≤ 1 VA (1P+N); ≤ 2 VA (3P/3P+N).
• Maximum Current: 63 A.
• Basic Current (Ib): 10 A.
• Operating Temperature: -25°C to +60°C (-13°F to +140°F).
• Overvoltage and Measurement Category: III.
• Temporary Surges: Supports temporary surges relative to the ground.
• Pollution Degree: 3.
• Altitude: ≤ 2000 m (6500 ft).
• Relative Humidity: Maximum 93% without condensation.
• Impact Resistance Index: IK05.
• Usage: For indoor use only.

Radio Communication:

• Frequency Band: 2.4 GHz ISM band (2400 MHz to 2483.5 MHz).
• Channels: 11 to 26 (IEEE 802.15.4).
• Equivalent Isotropic Radiated Power (EIRP): 0 dBm.
• Max. Transmitted RF Power: ≤ 10 mW (EIRP).

Accuracy:

• Voltage: Class 0.5.
• Current, Power, and Active Energy: Class 1.

Compliance

Schneider Electric Industries declares that the wireless-communication energy sensors PowerTag comply with the essential requirements and other relevant provisions of RED-DIRECTIVE 2014/53/EU and UK regulations SI 2017 No. 1206. The EU declaration of conformity No. FD16090201 and UKCA Declaration of conformity No. FD16090201_UK can be downloaded from se.com/docs.