User Manual for POWERCOME models including: MWRA37V Remote Control, MWRA37V, Remote Control, Control
Asia Socks Inc MWRA37V 2BBN3-MWRA37V 2BBN3MWRA37V mwra37v
User Manual DOC NO. VERSION DATE PC-SPE-230113001 A2 2023-04-27 Attachment 1 Remote control specification 1. Outline structure drawing Key LED /H gear /M gear /L gear /Off 2. Key and light display No Remote control instructions Remarks 1 Key LED Red indicator light 2 H gear/H 3 M gear/M 4 L gear/L High gear Middle gear Low gear 100% heating mode 100% 66% heating mode 66% 33% heating mode 33% 5 Off/ Power switch 3. Instructions for use 3.1 Pairing method Press the power button for 10S, LED1 and LED2 blink at 1HZ, press any key of the remote control for pairing within 30S, LED1 and LED2 will be extinguished after pairing, and exit automatically after 30S without pairing 10SLED1 LED2 1HZ 30S LED1 LED2 30S 3.2 When you press H/M/L gear respectively with the remote control button, the corresponding LED gear lights up. 30S, the load is not connected, and the LED light goes out H/M/L LED 30S LED 3.3 Code clearing method Press the power button for 10S, LED1 and LED2 perform 1HZ flash mode for 10 times, the code is cleared successfully, and the LED lamp will automatically turn off. 10S LED1 LED2 1HZ 10 LED 4. Transmission distance Transmission distance between the remote control and the power supply: 10 M 10 User Manual DOC NO. VERSION DATE PC-SPE-230113001 A2 2023-04-27 FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device has evaluated to meet general RF exposure requirement. The device can be used be in portable exposure without restriction. IC Statement This device complies with Industry Canada licenseexempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1)l'appareil ne doit pas produire de brouillage, et (2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement The device has evaluated to meet general RF exposure requirement. The device can be used be in portable exposure without restriction. Ce produit est conforme à la limite d'exposition aux IC RF fixée pour un environnement non contrôlé et est sûr pour l'exploitation prévue, comme décrit dans le présent manuelMicrosoft Word 2010