Mr Beams MB360XT-BRN-01 855691005953 0855691005953 1001983727
Mr Beams MB360XT-WHT-03 815995026115 0815995026115
mr beams remove light sensor indoor lighting with the convenience of the Mr Beams Wireless UltraBright Motion Sensor Ceiling Light MB990: https://www.mrbeams.com/mr-b. How to remove light sensor | Mr Beams Wireless LED Lightning LEDs are the most
Installation Instructions Wireless Motion Sensor LED Spotlight MB360XT Thank you for purchasing the Mr Beams® Wireless Spotlight. We are committed to eliminating darkness using the latest in Light-Emitting Diodes (LEDs). LEDs are the most efficient and durable light sources available. We are certain that your light will contribute to a safer environment and provide light where you need it at a very reasonable cost. Tips: · Use only new alkaline D-Cell batteries with 1.5V rating. · Do not mix old and new batteries. If batteries are not new, it may cause the light to malfunction. · Install batteries with polarity in correct position. · Light may activate when batteries are inserted. Simply take light into a dark room. Allow batteries to settle, then test activation. · If your light will not turn off, it means that it is time to replace the batteries. What is included per light: · 1 Wireless Spotlight · Mounting Base · 3 Screws · 3 Anchors LED Light What you need to install: · 1 Small Screwdriver · 3 D-Cell Alkaline Batteries Spotlight Features: Knuckle Screw Motion/Light Sensor: Light instantly turns on when it detects motion from up to 30 feet away. The light sensor conserves battey life by preventing the light from activating in daylight. Auto Shut-off: Light shuts off automatically after 20 seconds if no motion is detected. Bright LED: 200 Lumens covers up to 600 sq ft. Durable, Weather Resistant: Tight seals and UV resistant material allow the light to work in all weather conditions. Motion & Light Sensor Mounting Base Thumb Screw Mounting Base NOTE: Light sensor only allows Spotlight to activate in darkness. We recommend you test in a dark room or closet. 1. Remove the face of the 2. Pull face out from light by rotating counter- cup to reveal battery clockwise as shown above. compartment. 3. Push in battery door 4. Insert 3 D-cell 5. Attach battery door by tab and lift up to release. batteries with correct matching the tabs to the polarity. Make sure the rectangular holes and then flat ends of the batteries push down on front until are against the springs. the tab clicks into place. 6. Match arrows then turn clockwise. Make sure unit is securely closed to activate weatherproof seal. Changing Batteries 7. Test the motion sensor in a dark room for up to 5 minutes. When you re-enter the room, the light should activate with motion. 8. Remove mounting base by turning thumbscrew counter clockwise. Pull mounting base off stem of light. 9. Determine mounting location and mark the pilot holes. Use a drill to insert anchors before screwing in the base. Battery Caution: 1) Do not mix old and new batteries 2) Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or (Nickel Metal Hydride) batteries 3) Do not dispose of batteries in fire 4)Batteries should be recycled or disposed of as per state and local guidelines 10. Drive the screws through the holes on mounting base. Insert the stem back into mounting base and tighten the thumbscrew. www.mrbeams.com 11. Loosen the knuckle screw located on the stem of the light, to point the light in desired direction. Then tighten the screw to secure position. When changing the batteries, remove the stem of the light by twisting off the thumbscrew. Note: never change batteries on ladder; doing so can result in injury. * Visit our website to view installation video. * 1 year limited warranty. Visit site for details. 32333 Aurora Rd. Suite 100 Solon, OH 44139 877.298.9082Adobe PDF Library 15.0 Adobe InDesign CC 2015 (Macintosh)