Hookup TX-SR607 QUICK SETUP
Model : TX-SR607
See the other side of this sheet for the AV component hookup.
Speaker Hookup
Thank you for purchasing this product. This quick setup sheet shows the typical hookup method for connecting speakers and AV components (DVD player, TV, cable/satellite receiver). For more detailed hookup information and operating instructions, please see the Instruction Manual.
< North American / Taiwan models >
Powered subwoofer
Front Front high right right speaker speaker
Front Front left high left speaker speaker
Powered subwoofer
Center speaker
< Other models >
Front Front high right right speaker speaker
Front Front left high left speaker speaker
Center speaker
Speaker Layout (Main Room)
Front High Left
Front High Right
Front Left
TV Center
Front Right
Sub woofer
Surround Left
Listener
Surround Right
Surround Back Left
Surround Back Right
*1
3/8''-1/2'' (10-12mm)
*1
1/2''-5/8'' (12-15mm)
Surround back right
speaker
Surround right
speaker
Surround left
speaker
Surround back left speaker
Surround back right
speaker
Surround right
speaker
Surround left
speaker
Surround back left speaker
*1 The same signal is output from each jack.
(C) Copyright 2009 ONKYO CORPORATION Japan. All rights reserved.
SN 29344959
* 2 9 3 4 4 9 5 9 *
AV Component Hookup
See the other side of this sheet for the Speaker hookup.
With an HDMI cable you can send both audio and video with a single cable, making connecting simple and keeping wires neat. If you have an HDMI-compatible TV and players, you can connect them to the AV receiver with HDMI cables. Digital audio signals received at HDMI IN input are output by the speakers and headphones connected to the AV receiver.
IF NO HDMI
TV
If your TV or player doesn 't support HDMI, use the analog or digital connections shown below.
DIGITAL AUDIO
OUT
OUT
COAXIAL L
VIDEO OUT
DVD player
R
VIDEO 1 IN
TV
HDMI IN
Please ensure the monitor input
(VIDEO 1, VIDEO 2, VIDEO 3, etc.)
selected corresponds to actual
connection used.
HDMI
OUT
DVD/BD player
HDMI Cable/satellite
OUT receiver
Antenna input (e.g., RF IN)
Coaxial feed from TV antenna
If you are not using cable/satellite receiver, please refer to the instruction manual.
Using the HDMI Inputs
On the front panel
If there's no picture on your TV, you'll need to assign the HDMI inputs as necessary using the onscreen setup menus. If you connect your DVD/BD player to the AV receiver's HDMI IN 1, and connect your cable/satellite receiver to HDMI IN 3, as shown above, it's not necessary to change the default assignments.
Menu
1. Input Assign 2. Speaker Setup 3. Audio Adjust 4. Source Setup 5. Listening Mode Preset 6. Miscellaneous 7. Hardware Setup 8. Remote Controller Setup 9. Lock Setup
1. Input Assign 1. HDMI Input 2. Component Video Input 3. Digital Audio Input
11. HDMI Input
DVD/BD VCR/DVR CBL/SAT GAME AUX
HDMI 1 HDMI 2 HDMI 3 HDMI 4 FRONT
L
COAXIAL
DIGITAL OUT
VIDEO OUT
R
AUDIO OUT
Cable/ satellite receiver
Antenna input (e.g..RF IN)
Coaxial feed from TV antenna
If you are not using cable/satellite receiver, please refer to the instruction manual.
Using the Digital Inputs
On the front panel
If there's no sound, you'll need to assign the digital inputs as necessary using the setup menus on the AV receiver's display. If you connect your DVD player to the AV receiver's DIGITAL IN COAXIAL 1, and your cable/satellite receiver to the DIGITAL IN COAXIAL 2, as shown, it's not necessary to assign the digital input.
The onscreen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT or the COMPONENT VIDEO OUT, use the AV receiver's display when changing settings.
Acrobat Distiller 5.0.5 (Windows)