EcoStruxure™ Panel Server: Wireless Devices / Wi-Fi Antenna

Important Safety Information

⚠️ DANGER: HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

Failure to follow these instructions will result in death or serious injury.

• Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. Refer to NFPA 70E, CSA Z462, NOM-029-STPS, or local equivalents.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Turn off all power supplying this equipment before working on or inside the equipment.
• Always use a properly rated voltage sensing device to confirm power is off.
• Replace all devices, doors, and covers before turning on power to this equipment.
• Do not exceed the device's ratings for maximum limits.

This section also contains safety warnings in French, Spanish, German, Italian, Portuguese, Russian, and Chinese.

Installation Guide

Retain this instruction sheet for future use. Visit our website at www.se.com.

⚠️ NOTICE: HAZARD OF EQUIPMENT DAMAGE

Failure to follow these instructions can result in equipment damage.

• For each bend in the antenna's cable, the radius of curvature must be more than 100 mm (3.93 in.).
• The cable must not be wound in a loop.
• Remove the antenna from the roof for the transport of the equipment.

Dimensions

The antenna has the following approximate dimensions:

• Height: 155.8 mm (6.13 in.)
• Diameter at base: 35 mm (1.37 in.)
• Main body diameter: 18.2 mm (0.71 in.)
• Cable connector diameter: 8.2 mm (0.32 in.)

Installation Steps

Follow these steps for proper installation:

1. Remove the roof panel before drilling to prevent shavings from falling into the equipment.
2. Drill a hole for the cable gland.
3. Install a cable gland with a diameter of 10 to 12 mm (0.39 to 0.47 in.) to maintain IP31 protection.
4. Connect the antenna cable to the Panel Server.
5. Secure connections with the specified torque: 0.8 N•m (7.1 lb-in.).

Technical Characteristics

This information is also available in French, Spanish, German, Italian, Portuguese, Russian, and Chinese.

Radio Frequency Compliance Statements

EU Declaration of Conformity

Schneider Electric Industries SAS declares that the Panel Server is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU.

The EU declaration of conformity PS21060101(Advanced) and PS20042001(Universal) can be downloaded from www.se.com/docs.

• Operating frequency for Wi-Fi: 2.4 GHz and 5 GHz; for other devices: 2.4 GHz.
• Maximum radio-frequency power transmitted: Wi-Fi: ≤ 100 mW; IEEE 802.15.4: ≤ 10 mW.

UK Declaration of Conformity

Schneider Electric Industries SAS declares that the Panel Server is in compliance with the essential requirements and other relevant provisions of RED Directive UK SI 2017 No. 1206.

The UK declaration of conformity UK_PS20042001 can be downloaded from www.se.com/docs.

• Operating frequency for Wi-Fi: 2.4 GHz and 5 GHz; for other devices: 2.4 GHz.
• Maximum radio-frequency power transmitted: Wi-Fi: ≤ 100 mW; IEEE 802.15.4: ≤ 10 mW.

These compliance statements are provided in multiple languages within the original document.

RoHS Compliance

Contents of Toxic or Hazardous Substances or Elements

Key:

• ✔️ Indicates that the toxic or hazardous substance in all homogeneous materials for this part is below the limit requirement in SJ/T11363-2006.
• ❌ Indicates that the toxic or hazardous substance in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006.

Note: The products on sale may or may not contain all the parts/components listed here.