MVMT EB5584 TWS Earbuds: User Guide and Instructions

Getting Started

Turn On

Take the two earbuds out of the charging case. They will automatically turn on. Once the earbuds have powered up, you should hear a sound indicating that they have automatically connected with one another.

Turn Off

Long press the control button until the LED turns red to indicate not in use; this will turn off your device. Earbuds will turn off automatically if away from the case for more than 5 minutes.

Bluetooth Connectivity

Connecting to a Device

1. Power the device on. The earbuds will pair with one another automatically when they are turned on.
2. Turn on your device's Bluetooth from the Bluetooth menu and select "MV-EB5584".
3. When paired successfully, the device will make a tone to confirm the connection has been made to your device.
4. Remember to turn the earbuds off after each use to ensure the longest play time.

Note: The earbuds will reconnect automatically if your device has been paired previously. Depending on your device's type and configuration, manual reconnection may be required each time.

Charging

Charging the Earbuds

Place the earbuds into the charging case. The earbuds will automatically enter charging mode if the case is charged or connected to the power supply. The earbuds will display a red LED light while they are charging and turn off when they are fully charged.

Charging the Case

Use the provided cable to connect the charging case to the power supply.

Operation

Voice Assistant

To activate the voice assistant (e.g., Siri), press and hold the control button for 1.5 seconds.

Function Keys

1. Play/Stop Music: When playing music, quickly press either earbud's control button.
2. Volume Control: Adjust the volume via your connected device (e.g., mobile phone).
3. Answering Call: When a call is received, briefly press either earbud's control button. To hang up, briefly press once again.
4. Declining Call: When playing music, press and hold the control button for 1.5 seconds*.

*Note: If you hold the control button for 3 seconds, the earbuds will power down.

Specifications

Parameters

• Bluetooth version: v5.1
• Bluetooth range: Up to 30 ft (10 m)
• Frequency range: 2402 - 2480 MHz
• Earbud battery capacity: 30 mAh each
• Total playtime: 3 hours (16 hours with case)
• Total standby time: 120 hours
• Waterproof rating: IPX4

Charging Case

• Battery capacity: 300mAh
• Charging time: 2 hours
• Charging port: USB Type-C

*Playtime depends on individual use.

Safety and Compliance

Important Warnings

To prevent possible hearing damage, do not listen at high volume levels for long periods.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help or assistance.

This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions; 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Disposal Information

[i] This symbol indicates that electrical and electronic devices are to be collected separately. This product is designated for separate collection at an appropriate collection point. Do not dispose of as household waste. If the device uses batteries, they must be removed from the device and disposed of in an appropriate collection center. If the batteries cannot be removed, do not attempt to do it yourself, as it must be done by a qualified professional. Separate collection and recycling help conserve natural resources and prevent negative consequences for human health and the environment that might result from incorrect disposal.

Product Identification: MVMT EB5584 TWS Earbuds, IPX4 Splash Proof.