Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. 1.1. Delivery contents CAB 1.1. Check compatibility of vehicle and accessories USB Take down the SW-version and HW-version of the interface boxes, and store this
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and ...
v.LOGiC Intelligent Solution Interface V4-NBT Compatible for the F-series BMW with navigation system or radio and 6.5", 7", 8.8" or 10.25" monitor with 4+2pin HSD2 LVDS connector Version 02.07.2019 V4-NBT Product features · Plug and play media-controller with controls by factory infotainment (iDrive) · Own on-screen display and setup · No coding of vehicle/factory-infotainment necessary · On 8.8" and 10.25" 24:10 ultrawide monitor 3 picture format modes (split-mode with factory video, 16:9, 16:9 zoom, full screen and full screen zoom) · On 6.5" and 7" 16:9 monitor 2 picture format modes (full screen and zoom) · 3 AV-inputs · Controls of after-market devices (e.g. DVD-player, DVD-changer, ...) by factory infotainment (iDrive, see STA + Database for supported devices) · 2 trigger outputs (+12V max. 1A), separately adjustable switching events (CAN, ACC, rear-view camera, reverse gear, external navigation) · Video-in-motion · Rear-view camera input · Interactive lane lines · Automatic switching to rear-view camera input on engagement of reverse gear from all operation modes · AV3 can be used for front camera, automatic on parking operation, automatic return at 20km/h · Manual switching to rear-view camera (only for vehicles with PDC button) · Manual return from rear-view and front camera (cancellation of automatic switching) · Picture-in-picture mode combining after-market rear-view and front camera picture(s) with factory parking sensor graphics · Compatible with all factory video accessories (e.g. rear-view camera, Top-View, nightvison, DVD-changer, TV-tuner) · Rear-seat-entertainment output for AV-sources connected to the interface · USB update-port for software-updates by consumer Page1 Version 02.09.2019 V4-NBT Contents 1. Prior to Installation 1.1. Delivery contents 1.2. Check compatibility of vehicle and accessories 1.3. Setting the dip switches of the interface-box V4C-M637 1.4. LED's of the interface-box V4C-M637 2. Connection schema 3. Installation 3.1. 3.2. 3.3. 3.4. 3.5. 3.5.1. 3.5.2. 3.5.2.1. 3.5.2.2. 3.5.3. 3.5.3.1. 3.5.3.2. 3.5.3.3. 3.5.4. 3.5.4.1. 3.5.4.2. 3.5.5. 3.5.6. 3.6. 3.7. Connecting interface-box and harnesses Connection to the factory monitor Quadlock connector Connection to the vehicle-AUX-input Connecting peripheral devices AV-source(s) After-market front camera Connection to the after-market front camera Settings for connecting an after-market front camera After-market rear-view camera Connection to the after-market rear-view camera Settings for connecting an after-market rear-view camera Settings for OEM rear-view camera After-market navigation Connection to the after-market navigation by RGB Settings for connecting an after-market navigation by RGB Rear-seat-entertainment Configurable trigger outputs Interactive lane lines Picture settings Page2 Version 02.09.2019 V4-NBT 4. Operation 4.1. 4.1.1. 4.1.1.1. 4.1.1.2. 4.1.2. 4.1.3. 4.2. 4.3. 4.4. 4.5. 4.5.1.1. 4.5.1.2. OSD On-screen display OSD Operation iDrive High iDrive Low iDrive selection OSD Additional setting options Video-in-motion function Selecting the interface as current AV-source Assigning device controls Controlling the connected AV-sources Controlling by iDrive High Controlling by iDrive Low 5. Specifications 6. Connections (interface-box) 7. Technical support Appendix A Device control table Legal Information By law, watching moving pictures while driving is prohibited, the driver must not be distracted. We do not accept any liability for material damage or personal injury resulting, directly or indirectly, from installation or operation of this product. This product should only be used while standing or to display fixed menus or rear-view-camera video when the vehicle is moving, for example the MP3 menu for DVD upgrades. Changes/updates of the vehicle's software can cause malfunctions of the interface. We offer free software-updates for our interfaces for one year after purchase. To receive a free update, the interface must be sent in at own cost. Labor cost for and other expenses involved with the software-updates will not be refunded. Version 02.09.2019 V4-NBT Page3 1. Prior to installation Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. 1.1. Delivery contents Take down the SW-version and HW-version of the interface boxes, and store this manual for support purposes. Interface-box V4C-M637 HW_____ SW_____ LVDS cable CAB-HSD2-RR148 Video-harness V4C-VIDEO Audio-harness V4C-AUDIO Harness V4C-BM03 1.1. Check compatibility of vehicle and accessories Requirements Vehicle Navigation Limitations Factory-USB-port PDC / inter. lane lines 1series (F20/F21), 3series (F30/F31/F32/F33), X3 (F25), all other F-series vehicles from approx 06/2012, Mini Paceman 2014 F-series with navigation system or radio with 6.5", 7", 8.8" or 10.25" monitor with 4+2pin HSD2 LVDS connector The AUDIO connection is different if the vehicle is with factory USB-port, please see the note in chapter "Connection to the vehicle-AUX-input"! "PDC picture in picture" and "interactive lane lines" function is not simultaneously usable Page4 Version 02.09.2019 V4-NBT 1.2. Setting the dip switches of the interface-box V4C-M637 Dip 1 on the back of the interface-box V4C-M637 are used to set the monitor type. The default setting is: Vehicle/ navigation 6.5" monitor (ver.1) 6.5" monitor (ver.2) 7" monitor (ver.1) 7" monitor (ver.2) 8.8" monitor 10.25" monitor (ver.1) 10.25" monitor (ver.2) Dip 1 OFF OFF OFF OFF ON ON ON Dip 2 OFF OFF OFF ON OFF OFF ON Dip 3 OFF ON OFF OFF OFF OFF OFF After each change of the dip switch settings you have to execute a power reset of the interface-box! 1.3. LED`s of the interface-box V4C-M637 valid input source CAN ok valid signal Page5 Version 02.09.2019 V4-NBT 2. Connection schema Page6 Version 02.09.2019 V4-NBT Back of factory monitor Interface-box V4C-M637 FRONT 4+2Pin HSD2 LVDS female vehicle harness LVDS cable CAB-HSD2-RR148 Page7 Version 02.09.2019 V4-NBT 3. Installation Switch off ignition and disconnect the vehicle's battery! The interface needs a permanent 12V source. If according to factory rules disconnecting the battery is to be avoided, it is usually sufficient to put the vehicle is sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a resistor lead. If power source is not taken directly from the battery, the connection has to be checked for being start-up proven and permanent. Prior to wire and device installation we suggest to connect and test correct function of all after-market and factory infotainment equipment! The interface is installed on the backside of the factory monitor and on the backside of the navigation computer. 3.1. Connecting interface-box and harnesses Connect female 18pin Micro-Fit connector of harness V4C-BM0x to the male 18pin Micro-Fit connector (POWER) on the front of the interface-box V4C-M637. Connect female 14pin Micro-Fit connector of the video-harness V4C-VIDEO to the male 14pin Micro-Fit connector (VIDEO) on the rear of the interface-box V4C-M637. Connect female 16pin Micro-Fit connector of the audio-harness V4C-AUDIO to the male 16pin Micro-Fit connector (AUDIO) on the rear of the interface-box V4C-M637. Version 02.09.2019 V4-NBT Page8 3.2. Connection to the factory monitor Back of factory monitor Interface-box V4C-M637 FRONT 3 LVDS cable CAB-HSD2-RR148 1 2 4+2Pin HSD2 LVDS female vehicle harness Connect the female 4+2pin HSD2 LVDS connector of the LVDS cable CAB-HSD2-RR148 to the male 4+2pin HSD2 LVDS connector (LVDS-OUT) on the front of the interface-box V4C-M637. Remove the female 4+2pin HSD2 LVDS connector of the vehicle harness of the factory monitor and connect it to the male 4+2pin HSD2 LVDS connector (LVDS-IN) on the front of the interface-box V4C-M637. Connect the second female 4+2pin HSD2 LVDS connector of the LVDS cable CAB-HSD2-RR148 to the male 4+2pin HSD2 LVDS connector of the factory monitor. Page9 Version 02.09.2019 V4-NBT 3.3. Quadlock connector Remove the female Quadlock connector of the vehicle harness from the rear of the navigation computer. Remove optical leads from the female Quadlock connector of the vehicle harness and insert them into the female Quadlock connector of harness V4C-BM03 at the same position. Connect female Quadlock connector of vehicle harness to the male Quadlock connector of harness V4C-BM03. Connect female Quadlock connector of harness V4C-BM03 to the male Quadlock connector of the navigation computer Page10 Version 02.09.2019 V4-NBT 3.4. Connection to the vehicle-AUX-input Connect the audio-RCA of harness V4C-BM03 to the female RCA-connectors AUDIO OUT of the audio-harness V4C-AUDIO. Note: If the vehicle is with factory USB-port, the AUDIO-OUT of the audio harness V4C-AUDIO must be connected to the Audio-AUX jack bush which is next to the USBport (instead of to the male RCA on V4C-BM03 harness). If connecting a rear-set-entertainment an optional RCA Y-cable is plugged in between, see chapter "Rear-seat-entertainment" 3.5. Connecting peripheral devices It is possible to connect 3 after-market AV-sources, therefrom optional an an after-market front camera, an after-market rear-view camera, an after-market navigation and rear-seatentertainment to the interface. Before final installation of the peripheral devices, we recommend a test-run to detect incompatibility of vehicle and interface. Due to changes in the production of the vehicle manufacturer is always the possibility of incompatibility. Version 02.09.2019 V4-NBT Page11 3.5.1. AV-source(s) The interface has the possibility to connect and remotely control by navigation buttons 3 pre-programmed devices. The device list in the device control table (appendix A) shows the pre-programmed remote channels and the related IR-remote cables STA-xxx which must be ordered separately for the control of the device. Connect video RCA of AV-source 1 to female RCA connector VIDEO-1, the video RCA of AV-source 2 to female RCA connector VIDEO-2 and video RCA of AV-source 3 to female RCA connector VIDEO-3 of the video-harness V4C-VIDEO. Connect audio RCA of AV-source 1 to female RCA connectors AUDIO-1, the audio RCA of AV-source 2 to female RCA connectors AUDIO-2 and audio RCA of AV-source 3 to female RCA connectors AUDIO-3 of the audio-harness V4C-AUDIO. Using the respective STA-xxx IR-control cable, interconnect the blue-black (yellowblack) female 3pin AMP connector of harness V4C-BM03 and the IR-port of the AVsource 1 (AV-source 2). If 3 AV-sources are connected, connect the optionally available IR-control cable STA-Y between the blue-black female 3pin AMP connector and the IR-ports of the AV-sources 1 and 3. Version 02.09.2019 V4-NBT Page12 3.5.2. After-market front camera 3.5.2.1. Connection to the after-market front camera Connect the video RCA of the after-market front camera to the female RCA connector VIDEO-3 of the video-harness V4C-VIDEO. - The green wire of harness V4C-BM03 can be used for +12V electric power supply (max. 1A) of the after-market front camera. Configure in the OSDmenu "OPTION", menu item "POWER OUT 2" the designated electric power supply (see chapter "Configurable switching outputs"). - Note: The after-market front camera is always connected to AV3. Page13 Version 02.09.2019 V4-NBT 3.5.2.2. Settings for connecting an after-market front camera You have to configure some settings in the OSD-menus INPUT and OPTION if you want to connect an after-market front camera (Operation of the OSD: see chapter "OSD-Operation"). OSD-menu INPUT OPTION Menu item AV3 FVC Setting OFF OFF ON PDC PARK LOGIC RGearOnly RGearSpeep RGearTime RVC GRAPHIC PIP1 Explication The front camera is connected to AV3 Keine Frontkamera angeschlossen Switches to front camera if parking process is enabled and reverse gear is released For vehicles with PDC button. Enabled while parking process and up to 20 km/h or together with PDC if existing Enabled while parking process Enabled while parking process and up to 20 km/h Enabled while parking process and up to 20 second OEM PDC display of the vehicle Note: You can deactivate the enabled parking process by pressing the iDrive or by enabling other modes (e.g. radio). After deactivation you can't enable the parking process again until the vehicle is diving faster than 20km/h, the ignition is switched off and on or the PDC will be disabled and enabled again, if existing. Page14 Version 02.09.2019 V4-NBT 3.5.3. After-market rear-view camera 3.5.3.1. Connection to the after-market rear-view camera Connect the video RCA of the after-market rear-view camera to the female RCA connector of the video-harness V4C-VIDEO. - The green wire of harness V4C-BM03 can be used for +12V electric power supply (max. 1A) of the after-market rear-view camera. Configure in the OSD-menu "OPTION", menu item "POWER OUT 2" the designated electric power supply (see chapter "Configurable switching outputs"). Page15 Version 02.09.2019 V4-NBT 3.5.3.2. Settings for connecting an after-market rear-view camera You have to configure some settings in the OSD-menus INPUT and OPTION if you want to connect an after-market rear-view camera (Operation of the OSD: see chapter "OSDOperation"). OSD-menu INPUT OPTION Menu item RVC Setting OFF ON PDC PARK LOGIC RGearOnly RGearSpeep RGearTime PIP1 RVC GRAPHIC LINES Explication No rear-view camera connected Switches to rear-view camera if reverse gear is engaged and/or PDC-display is displayed For vehicles with PDC button. Enabled while parking process and up to 20 km/h or together with PDC if existing Enabled while parking process Enabled while parking process and up to 20 km/h Enabled while parking process and up to 20 second OEM PDC display of the vehicle activated Interactive lane lines activated Note: You can deactivate the enabled parking process by pressing the iDrive or by enabling other modes (e.g. radio). After deactivation you can't enable the parking process again until the vehicle is diving faster than 20km/h, the ignition is switched off and on or the PDC will be disabled and enabled again, if existing. 3.5.3.3. Settings for OEM rear-view camera OSD-menu INPUT Menu item RVC Setting OEM OPTION PARK LOGIC PDC Explication If a factory rear-view camera is existing! The interface turns off, if PDC or reverse gear is enabled and it displays factory rear-view camera and/or PDC-display For vehicles with PDC button. Enabled while parking process and up to 20 km/h or together with PDC if existing Version 02.09.2019 V4-NBT Page16 3.5.4. After-market navigation 3.5.4.1. Connection to the after-market navigation by RGB Connect the male 6pin connector of the video-harness V4C-VIDEO to the aftermarket navigation. - The pink wire of harness V4C-BM03 can be used for +12V switching voltage (max. 1A) of the aftermarket navigation. Configure in the OSD-menu MISC, menu item POWER OUT 1 to "ACC" (see chapter "Configurable switching outputs"). Note: It is possible to connect the after-market navigation to an AV-input alternatively. Version 02.09.2019 V4-NBT Page17 3.5.4.2. Settings for connecting an after-market navigation by RGB You have to configure some settings in the OSD-menu INPUT if you want to connect an aftermarket navigation (Operation of the OSD: see chapter "OSD-Operation"). OSD-menu INPUT Menu item RGB Setting OFF 800x480 Explication No after-market navigation connected After-market navigation connected by RGB Page18 Version 02.09.2019 V4-NBT 3.5.5. Rear-seat-entertainment Connect the video RCA of the rear-seat-entertainment to the female RCA connector VIDEO-OUT of video-harness V4C-VIDEO. Connect the audio-RCA of the rear-seat-entertainment to the female RCA connectors of the optional RCA-Y-cable. Connect the audio RCA of the optional RCA-Y-cable to the female RCA connectors AUDIO OUT of the audio-harness V4C-AUDIO. Connect the audio RCA of harness V4C-BM03 to the female RCA connectors of the optional RCA-Y-cable. Note: The last source keeps active on rear-seat-entertainment if you switch the navigation to OEM mode. Version 02.09.2019 V4-NBT Page19 3.5.6. Configurable trigger outputs You can configure the both +12V trigger outputs separately. The pink wire is POWER OUT 1 and the green wire is POWER OUT 2. Note: You can configure the both trigger outputs in the OSD-menu OPTION separately (Operation of the OSD: see chapter "OSD-Operation"). OSD-menu OPTION Menu item POWER OUT1 (pink) POWER OUT2 (green) Setting CAN ACC CAM RGEAR AVS OFF Explication +12V when the interface is on (red LED on) +12V when ignition is on +12V when the rear-view camera input (AV4) is activated +12V when reverse gear is engaged +12V when interface video-source is active (for external audio switch) Trigger putput deactivated Version 02.09.2019 V4-NBT Page20 3.6. Interactive lane lines You have to configure some settings in the OSD-menu OPTION if you want to activate interactive lane lines (Operation of the OSD: see chapter "OSD-Operation"). OSD-menu OPTION Menu item RVC LINES CAR TYPE Setting LINES 1/2/3/4/5/6/7/ X1/X3/X4/X5/X6/ Z4/i3 Explication Interactive lane lines activated Vehicle type selection Note: "PDC picture in picture" and "interactive lane lines" function is not simultaneously usable. Page21 Version 02.09.2019 V4-NBT 3.7. Picture settings The picture settings and picture format can be changed in the OSD menu (activation only possible from interface AV level by long pressing the OPTION -button). In addition, the RC code can also be set. The following options are available: IR Code Brightness Contrast Saturation Hue Sharpness Format = - 8.8" and 10.2" 24:10 ultrawide monitor: -FULL = 24:10 video full screen mode -ZOOM = 24:10 video full screen mode zoom -AV+LVDS = 16:9 video on left side, factory picture on right side - 6.5" and 7" 16:9 monitor: -FULL = 16:9 video full screen mode -ZOOM = 16:9 video full screen mode - zoom Note: The picture / format/ RC code settings will be retained for each AV-source separately. Page22 Version 02.09.2019 V4-NBT 4. Operation 4.1. OSD On-screen display You can change the basic configurations of the interface in the OSD (on screen display). 4.1.1. OSD Operation You can control the OSD by iDrive. 4.1.1.1. iDrive High Options Back OK Options OK Short press= leave OSD Options Long press = enter OSD Page23 Version 02.09.2019 V4-NBT 4.1.1.2. iDrive Low Back OK Options OK Short press= leave OSD Long press = enter OSD 4.1.2. iDrive selection OSD menu ,,OPTION" ,,IDRIVE" is for setting the right iDrive control knob. OSD-menu Menu item OPTION IDRIVE Setting LOW HIGH Explication Vehicles with iDrive Low control knob Vehicles with iDrive High control knob Page24 Version 02.09.2019 iDrive High iDrive Low V4-NBT 4.1.3. OSD Additional setting options The following settings in the OSD-menus OPTION and OSD can be configured over and above the described settings in this manual (Operation of the OSD: see chapter "OSD-Operation"): OSD-menu OSD INFO OPTION Menu item POS. X POS. Y SIZE OsdTimeOut VERSION FACTORY RESET Setting 0-xxx 0-xxx SMALL LARGE 01-20 X.XX.XX Explication Horizontal position of the OSD Vertical position of the OSD Small OSD menu windows Large OSD menu windows OSD menu timeout Displays the current SW-version Resetting to factory settings 4.2. Video-in-motion function It is possible to activate and deactivate the video-in-motion in the OSD menu "OPTION" (Operation of the OSD: see chapter "OSD-Operation"). OSD-menu OPTION Menu item VIM Setting ON OFF Explication Video-in-motion activated Video-in-motion deactivated Page25 Version 02.09.2019 V4-NBT 4.3. Selecting the interface as current AV-source In the vehicle's CD/Multimedia > External devices menu, activate AUX front by iDrive and after it long press MEDIA-button respectively long press AUDIO-button to choose the interface as current AV-source. Short press MEDIA button respectively AUDIO button to switch the AV-sources. Each short press will switch to the next enabled input. If all inputs are enabled the order is: AV1 à AV2 à AV3 à RGB à RVC à FVC à AV1 à... Inputs which are not enabled are skipped. The exiting of the video interface level is achieved by long press of BACK button or short press of RADIO / MENU / TEL / NAV button. 4.4. Assigning device controls You can assign the device controls in the OSD-menu INPUTS (Operation of the OSD: see chapter "OSDOperation"). Assign related IR-codes AV1 for AV-source 1, AV2 for AV-source 2 and AV3 for AV-source 3 as described in device control table (see appendix A) Note: The IR-control channel AV1 is preset to IR-Code 41 compatible DVB-T tuners If you connect an AV-source without control you have to assign any IR code for the respective AV-input (AV1/2/3) because in the setting ,,OFF" there is no picture visible. Page26 Version 02.09.2019 V4-NBT 4.5. Controlling of the connected AV-sources The picture shows which functions of the connected devices can be executed by iDrive. Once an AV-input is activated the iDrive action will execute the function described in the picture. The function description equals the remote control buttons of the device's remote control. On the additional device the writing on the remote control buttons may vary (e.g. AV instead of Source). 4.5.1.1. Controlling by iDrive High Controlling of AV-sources: DVB-T / DVD / DAB Short = Ç / Ç / Ç Long = Menu/ PBC/ SETUP Short = Switch AV-sources Long = Switch picture format Short = VOL/ 9/ Å Long = Exit/ Play/ F+/- Short = VOL +/ : / Æ Long = Scan/ Zoom(Disc)/ SCAN Turn = CH+-/ 9 : / ÇÈ Short = OK/ Enter/ OK Long = Power/ Power/ Power Short = Exit/ Play/ F+/Long = back to the main menu Short = È / È / È Long = AV /AV/ SOURCE Short = Menu/ PBC/ SETUP Long = enter OSD Note: A few functions could be different on some connected devices. Page27 Version 02.09.2019 V4-NBT 4.5.1.2. Controlling by iDrive Low Controlling of AV-sources: DVB-T / DVD / DAB Short = Switch AV-sources Long = Switch picture format Short = VOL/ 9/ Å Long = Exit/ Play/ F+/- Turn = CH+-/ 9 : / ÇÈ Short = Exit/ Play/ F+/Long = back to the main menu Short = VOL +/ : / Æ Long = Scan/ Zoom(Disc)/ SCAN Short = OK/ Enter/ OK Long = Power/ Power/ Power Short = Menu/ PBC/ SETUP Long = enter OSD Note: A few functions could be different on some connected devices. Page28 Version 02.09.2019 V4-NBT 5. Specifications Operation voltage 10.5 14.8V DC Stand-by power drain <0,1mA Operation power drain 190mA Power consumption 2,6W Temperature range -20°C to +80°C Weight (box only) 285g Measurements (box only) B x H x T 141 x 30 x 105 mm 6. Connections (interface-box) Male 4+2pin HSD2 LVDS connector Male 4+2pin HSD2 LVDS connector Interface-box V4C-M637 REAR Female update-connector Mini USB Male 14pin Micro-Fit connector Interface-box V4C-M637 FRONT Male 16pin Micro-Fit connector Male 18pin MicroFit connector 7. Technical Support Caraudio-Systems Vertriebs GmbH manufacturer/distribution In den Fuchslöchern 3 D-67240 Bobenheim-Roxheim email support@caraudio-systems.de Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered trademarks ® of their corresponding legal owners. Page29 Version 02.09.2019 V4-NBTmacOS Version 10.14.4 (Build 18E226) Quartz PDFContext Word