Orren Ellis 48-inch LED Mirror

Key Features

• ? Energy-Saving LED Lighting
• ✨ Frameless Design
• ? Integrated Touch Screen Interface
• ? Smart Defogger Function
• ? Bluetooth Audio Connectivity
• ⏰ Digital Clock and Temperature Display
• ⚙️ Multifunction Control

Product Characteristics

This 48-inch LED mirror features an integrated defogger, a modern frameless design with dimming capabilities, energy-efficient LED lighting, a touch screen interface, Bluetooth audio, and a digital clock with temperature display.

Diagram Descriptions:

• Front View: Depicts the mirror surface with the location of the multi-function touch control screen.
• Side View: Illustrates the mirror's thickness and the aluminum frame.
• Back View: Shows the PVC backboard, the defogger element, and the Bluetooth speaker.

Quick Start

1. Turn off electrical power at the breaker (verify with a tester).
2. Locate wall studs and mark the center line.
3. Install the mounting bar/brackets level.
4. Make the wired electrical connections.
5. Hang the mirror; use the lock latch for horizontal mounting.
6. Restore power; test the touch sensors (lighting, defogger).

Safety and Compliance

• Installation must be performed by a licensed electrician only.
• Connect to a GFCI protected, properly grounded circuit (120V~ 60Hz).
• Do not connect to a wall dimmer (ELV/triac). Use a standard ON/OFF switch if wall control is desired; dimming is controlled on the mirror.
• Two-person lift required; use PPE (Personal Protective Equipment).
• Mount into wall studs whenever possible; use appropriate anchors for the wall type.

Safety Icons:

• ⚠️ DANGER
• ⚡ GFCI Protected
• ? No Wall Dimmer
• ? Grounding
• ?‍?‍? Two-person Lift
• ⛑️ PPE

Box Contents and Tools

Included:

• Mirror Assembly
• Suspension Bar
• Wall Screws (x2)
• Anchors (x2)

Tools Required:

• Measuring Tape
• Level
• Pencil
• PPE
• Drill Bits
• Electric Drill
• Phillips Screwdriver
• Stud Finder

Wiring Instructions

❗ Warning: Manufacturer's warranty will be void if the product is not installed by a licensed professional.

Before starting installation, ensure that:

• The wall where the product is installed can support its weight.
• The main power supply has been turned off to complete the installation.

IMPORTANT: WIRING INSTRUCTIONS FOR CANADA AND THE UNITED STATES

The wire colors of this fixture do not align with North American standard guidelines. For safe installation, please re-identify the fixture wires with electrical tape as follows:

• LIVE: Wrap the fixture's White wire with black tape. Connect it to your home's Black (Live) wire.
• NEUTRAL: Wrap the fixture's Black wire with white tape. Connect it to your home's White (Neutral) wire.
• GROUND: Connect the Green wire to your home's Green or bare Copper ground wire.

Diagram Descriptions:

• Wires: Illustrates the fixture's Live (White), Neutral (Black), and Ground (Green) wires.
• Connections: Shows the connections between the fixture wires and the home's Live, Neutral, and Ground wires.

Important Notes:

• Wiring only. Do not attach a cord and plug.
• Use approved wire connectors; make all splices inside approved boxes.
• Do not use a wall dimmer. Use a standard ON/OFF switch if wall control is required.

Wall Mounting Instructions

1. Measure and Drill: Measure the distance for mounting holes. Drill holes in the wall.
2. Insert Anchors: Insert the anchor and mounting screw into the wall.
3. Connect and Hang: Connect the mirror wires to your main wires. Hang the mirror by its mounting hole onto the screw on the wall.
4. Finalize: Remove the protective film and clean the mirror with a cloth.

Operation and Features

Model: M-971-48

The multi-function touch control screen allows operation of various features:

• ? Lighting: Touch to turn lighting on/off. Touch and hold to adjust brightness.
• ? Defogger: Touch to activate/deactivate the defogger.
• ? Bluetooth Speaker: Touch to turn the Bluetooth speaker on/off.
• ⏰ Clock/Temperature: Short touch for play/pause. Long touch (3 sec.) enters clock programming mode. In programming mode, the clock cycles through 4 fields with a 3-sec pause. To set the time, press while the field is flashing.
• ⏭️ Track Control: Touch for next track.
• ? Volume Up: Touch and hold for 3 sec. to increase volume.
• ? Volume Down: Touch and hold for 3 sec. to decrease volume.

Maintenance & Cleaning

• Wipe with a soft, lint-free cloth; use a mild cleaner without ammonia.
• Do not use abrasives, scouring pads, acids, or solvents.
• Apply cleaner to the cloth, not directly onto the sensor areas.

Troubleshooting (Quick Solutions)

• No lighting upon installation: Confirm the breaker is ON, check wiring, ensure internal quick connectors are properly seated. (?)
• Touch sensor not responding: Turn off power at the breaker for 60 seconds; clean/dry the glass over the sensors. (?)
• Buzzing/Humming: Ensure the unit is not connected to a wall dimmer; verify grounding. (?)
• Defogger not heating: Ensure the left sensor is ACTIVE; the function automatically turns off after 1 hour. (? ⏱️)