ILIFE X1000 Robotic Vacuum Cleaner

About Safety

1. This device is not suitable for use by children under 8 years old or individuals with physical or emotional disabilities. If used by such individuals, supervision by a guardian is required. Do not let children sit on or play with the robot as a toy.
2. Remove obstacles before using the robot, such as power cords and other items. Fold the edges of carpets under the carpet. Ensure curtains and tablecloths do not touch the floor.
3. If the environment includes stairs, test the robot to see if it can detect the edge of a fall without dropping.
4. Follow the instructions to operate the robot.
5. Ensure the power supply voltage matches the voltage marked on the charging base.
6. Use only in indoor and home environments. Do not use in outdoor, commercial, or industrial environments.
7. Only use the original rechargeable battery and charging base provided by the manufacturer. Non-rechargeable batteries are strictly forbidden. Refer to technical parameters for battery specifications.

About Product

8. Do not flush the robot directly with water.
9. Do not wipe the robot with a wet cloth.
10. Do not use on wet or watery floors.
11. Do not use in environments with open flames or fragile items.
12. Keep hair, cloth, and fingers away from the product's openings or operating parts.
13. Do not allow the robot to suck materials that might block the device, such as stones or waste paper.
14. Do not absorb flammable materials, such as gasoline or toner for printers/photocopiers.
15. Do not allow the product to absorb burning items, such as cigarettes, matches, ashes, or other products that may cause a fire.
16. Do not place the product on the suction mouth. Do not use the robot if the suction mouth is blocked. Clean dust, hair, cotton, etc., to ensure smooth airflow at the suction mouth.
17. Do not use a damaged charging base.
18. Use the power cord carefully to avoid damage. Do not use the power cord to drag or pull the product or its charging base. Do not allow the robot to run on the power cord and keep the power cord away from heat sources.
19. If the power cord is damaged, it must be replaced by qualified maintenance staff to avoid danger.
20. Ensure the dust bin and filter are properly installed before use.
21. Do not use the robot in an infant sleeping room.
22. Do not use the robot if it cannot work properly due to drops, damage, water, or outdoor use. Let the robot be repaired by the manufacturer or its service department.
23. If the product is not used for a long time, disconnect the power supply.

About Maintenance

24. Before cleaning and maintaining the product, turn off the power switch first.
25. Before cleaning and maintaining the product, pull the power cord out of the power socket.

About Disposal

26. Before disposing of the product, remove it from the charging base, turn off the power switch, and remove the battery.
27. Before disposing of batteries, follow local laws and regulations.
28. It is forbidden to incinerate the product, even if severely damaged, as the battery may cause an explosion.
29. Follow the instructions for product use. The company will not take responsibility for any loss or damage due to improper use.

List of Accessories

• Host (With Two Batteries)
• Charging Station
• Power Adapter
• Suction Port Parts
• User Manual
• Front Roller Fluff Assembly Parts

Main Body

The main body of the robot includes the following components:

• Switch
• Display
• Anti Collision sensor
• Side Brush (two located on the underside)
• Roller Brush (located on the underside)

Diagrams show the top view with Switch and Display, and the underside with Anti Collision sensors, Side Brushes, and Roller Brush.

Component Identification

The charging station features a QR Code and Charging Pins.

The robot itself contains:

• Dustbin
• Filter Screen (inside the dustbin)
• Battery (accessible via a compartment)
• Charging Pins (on the robot's underside for docking)

Diagrams illustrate the charging station with QR codes and pins, and the robot with its dustbin, filter screen, and battery compartment.

Preparation Before Using

Follow these steps before the first use:

1. Remove the machine from the packaging.
2. Lift the dustbin.
3. Press the dustbin button to open its bottom cover.
4. Reach into the dustbin and remove the protective packaging material (pearl cotton).
5. Reattach the dustbin to the host.

Diagrams show the sequence of opening the dustbin and removing packaging.

Install the Battery

Lift the battery compartment cover. Insert the battery into the slot according to the indicated direction. Press both sides of the battery simultaneously until you hear a "click," indicating successful installation.

Diagrams show the battery being inserted into the robot.

Charging Mode

To set up charging:

1. Connect the adapter to the charging station.
2. Place the charging station flat against a wall, ensuring the surrounding area is clear and not obstructed.
3. Connect the power adapter to a power outlet.
4. Press the host switch button to turn on the robot.

Diagrams illustrate connecting the charging station and the robot docking.

? Tips: After cleaning, it is recommended to keep the robot in the charging station rather than turning it off completely, to ensure it is ready for the next use.

Charging

Auto Charge: Press the recharge button (?) on the robot panel or in the app. The device will automatically search for and dock with the charging base.

? Tips: During daily use, clean the charging pins on both the robot and the charging station regularly to ensure effective charging.

? Tips:

1. For daily use, ensure the robot is placed on the charging station, the station is connected to power, and the robot's power switch is on.
2. If the robot is not used for an extended period, fully charge the machine, turn off the power, and store it in a dry, ventilated place.

Switch/Pause

Switch (Start/Stop): Ensure the power is on. Press the power button (▶️) on the robot or via the app to start cleaning. Press the same button again to pause cleaning.

? Tips: If the robot is in sleep mode, press the power button (▶️) to wake it up and enter the function selection mode. Press the button again to start working automatically.

Mode Selection

The robot offers several cleaning modes, selectable via dedicated buttons on the robot or app:

1. Energy Saving: Press the energy saving button (?) on the robot.
2. Standard Mode: Press the standard button (?) on the robot.
3. Strong Mode: Press the power button (⚡) on the robot.
4. Max Mode: Press the MAX button (?) on the robot.
5. Customize: Press the customize button (?) to adjust settings like side brush speed, roller brush speed, volume, and suction value.

APP Download

The robot can be controlled via the "ILIFEHOME" app. Scan the provided QR codes to install the app on your iOS or Android device.

Diagrams show QR codes labeled "ILIFEHOME" for iOS and Android.

Connected APP

? Tips: Connect your phone to an available WiFi network in the room. Ensure your phone is connected to a stable WiFi network indoors with good signal quality.

Steps to connect the app:

1. Turn on the robot to enter standby mode.
2. Click the machine menu button on the app.
3. Click the WLAN button on the machine or select the Settings button to enter WLAN settings.
4. Click to use AP network.
5. Click OK; the device will prompt "WIFI connecting".
6. The robot will indicate that the network is being configured.
7. Select your country or region from the list.
8. Register an email account and agree to the User Registration Agreement.
9. Click to add the robot.
10. Click "Next" to proceed.
11. Fill in the WiFi password and click "Next".
12. Click Settings to jump to the phone's settings page, then click WIFI settings and select the wireless network from the host (e.g., adh-XXX).
13. The connection is successful, and binding is completed.

? Note: If the connection fails, restart the device and follow the configuration steps again.

Diagrams illustrate the app interface and connection process.

Unconnected APP

On the app's device list page, press and hold the device you wish to disconnect. Swipe left, and an "Unconnected" button will appear. Click the "Unbind" button to unbind the device.

Diagram shows the app interface with a device and an unbind option.

Control Robot

Click to select the desired device from the list to enter the device control page.

Diagrams show the app interface for selecting and controlling the robot.

Side Brush Maintenance

Remove the side brush and wipe it with a clean cleaning cloth.

Diagram shows a hand removing a side brush.

Roller Brush Maintenance

Remove the dustbin. Lift out the roller brush box. Hold the two buttons with your hands, pull out the plug, and use the cleaning tool to cut away any hair wrapped around the roller brush.

Diagrams show the steps for removing and cleaning the roller brush.

Multi-directional Castor Maintenance

Remove the castor and clean it to reduce entanglement of hair and other particles.

Diagrams show the castor removal and cleaning.

Dust Bin and Filters Maintenance

1. Clean the dustbin in time after each use.
2. Remove the dustbin. Press the button on the dustbin; the bottom cover will pop open automatically. Empty the dust inside.
3. Remove the filter from the dustbin. Wash the filter with clean water and ensure it is completely dry before reinstalling.

Diagrams show the dustbin removal and emptying process.

Filter Cleaning

Remove the high-performance filter. Wash it with clean water and place it in a cool, ventilated place to dry. Do not squeeze the high-performance filter.

Diagrams show the filter removal and washing process.

Cliff Sensors and Charging Pins Cleaning

Gently wipe the cliff sensors and battery connector with a cleaning tool, as shown in the diagrams.

? Tips: Clean the charging pins regularly when there is dust on the cover.

? Tips:

• When the device is not used for a long time, take out the battery and store it properly. If the battery leaks, remove the battery and wipe the affected area.
• This device uses a long-life battery and does not require frequent replacement. If replacement is needed, contact after-sales service.

Diagrams show the location of cliff sensors and charging pins on the robot.

Maintenance and Replace Accessories Regularly