the LEGACY section of this manual. Additional information is also found in the LEGACY System Manual, available online at www.lionel.com.. Note! Note! Running your locomotive Figure 2. LEGACY engine selection Figure 3. LEGACY start-up LEGACY Control operations Your locomotive is designed for operation with the Lionel LEGACY system.
78-1179-250 8/14 Lionel 2-8-2 Heavy Mikado Steam Locomotive Owner's Manual Featuring Congratulations! Congratulations on your purchase of this Lionel steam locomotive! On the outside, this locomotive features numerous details and expert decoration in your favorite livery. Inside the boiler and tender, this locomotive is equipped with some of the most advanced sounds and controls in model railroading. This powerful locomotive is ready for duty on your layout. Contents of your locomotive box 1 Steam locomotive 1 Tender 1 Smoke fluid funnel 1 Wrench 4 Replacement traction tires 1 Owner's manual 1 Engine memory module The following Lionel marks are used throughout this Owner's Manual and are protected under law. All rights reserved. Lionel®, LionChiefTM, LionChief PlusTM, LEGACYTM, FasTrack®, TrainMaster®, Odyssey®, RailSounds®, CrewTalkTM, TowerComTM, DynaChuffTM, StationSoundsTM, Pullmor®, ElectroCouplerTM, MagneTraction®, CAB-1® Remote Controller, American Flyer®, Lionel ZW®, ZW®, MagniVision®, TMCC®, Lionelville®, Wireless TetherTM, PowerhouseTM, LionMaster®, Conventional ClassicsTM, Postwar Celebration SeriesTM, TruRailTM, PH-1 Powerhouse®, Powermaster®, Powerstation-Powerhouse®, Accessory Motor ControllerTM, AMCTM, Accessory Switch ControllerTM, ASCTM, Action Recorder ControllerTM, ARCTM, Track Power Controller 300TM, TPC 300TM, Track Power Controller 400TM, TPC 400TM, Block Power ControllerTM, BPCTM, Operating Track ControllerTM, OTCTM, FatBoyTM, Lionel Lines®, Joshua Lionel Cowen SeriesTM, Lockon®, TrainSoundsTM, MultiHornTM, MultiWhistleTM, Choo-ChooTM, SensorTrackTM 2 Table of contents Running your locomotive LEGACY Control operations 4 TrainMaster Command Control (TMCC/Command Control) operations 5 Conventional transformer operations 6 Locomotive basics Tender volume control location 7 Adding smoke fluid to your locomotive's smoke generator 7 Locomotive switch locations 8 Assigning your locomotive a new ID# (LEGACY and TMCC) 9 LEGACY Control System operations LEGACY Control System Engine Memory Module 10 The LEGACY CAB-2 Remote Controller 11 The Velocity Throttle 12 The Multi-Controller 12 The Train Brake Slider 12 The Warning Sound Controller 13 The Speed Bar 13 EFX Trim and EFX Bar Graph 14 Leaving the Preset Speed Screen 14 LEGACY RailSounds Sound System operations LEGACY RailSounds sound system 15 LEGACY RailSounds Sequence Control 16 CrewTalk dialog and TowerCom announcements in the LEGACY environment 17 LEGACY RailSounds sound system dialog on a round trip 18 TrainMaster Command Control operations CAB-1 Remote Controller commands 19 CAB-1 Remote Controller numeric keypad commands 20-21 Conventional transformer operations Using the LEGACY RailSounds sound system in the conventional environment 22 Activating CrewTalk dialog and TowerCom announcements 22 Locking your locomotive into a single direction 23 Odyssey II Speed Control system operations Odyssey II Speed Control operations 24 Odyssey II Speed Control system LEGACY Control operation 24 Odyssey II Speed Control system TrainMaster Command Control operation 24 Odyssey II Speed Control system conventional transformer operation 24 Maintaining and servicing your locomotive Reprogramming your locomotive to restore features 25 Lubricating your locomotive 26 Servicing your locomotive's LEDs 27 Replacing the traction tires 27 Locomotive diagnostics 28 Notes 29 Lionel Limited Warranty Policy & Service 30 3 Running your locomotive Note! Power your locomotive with an alternating-current (50-60Hz AC) transformer only. Powering your locomotive with a direct-current (DC) transformer, or in excess of 19 volts AC, may result in damage to sensitive electronic components. Note! Your locomotive requires Lionel or Lionel-compatible O-54 or larger track curves. LEGACY Control operations Your locomotive is designed for operation with the Lionel LEGACY system. It will also operate on the original Lionel Trainmaster System (TMCC1) with limited features and also on the LEGACY Cab-1L / Base-1L operating system (again with reduced features.) Using a Lionel LEGACY set (6-14295) will allow you to access ALL the features this locomotive has to offer. Your commands are sent by the Remote Controller to the Command Base, which broadcasts a radio frequency Figure 1. Drawbar connection that is distributed through the outer rails of the track to your locomotives. Your locomotive will not respond until it recognizes its unique ID#, so you can operate multiple Command-equipped locomotives on the same track at the same time. 1. Turn off track power, and then plug in the LEGACY Base and connect it to the track. 2. Place your locomotive and tender on the track and connect the drawbar as shown in Figure 1. 3. Increase track power voltage to full power (no more than 19 volts AC). If a circuit breaker Figure 2. LEGACY engine selection trips when you turn on the Lionel power supply, check the wheels of your locomotive to make sure they are all securely on the track. Check to make sure the track is free of all metals that may cause a short circuit. 4. As illustrated in Figure 2, press ENG and 1 (or your selected ENG ID#) to address the locomotive with your LEGACY CAB-2 Remote Controller. 5. Press the Start Up key on your LEGACY CAB-2 Remote, shown in Figure 3. Then, throttle up and move 'em out! Your engine sound will start up, Figure 3. LEGACY start-up and the locomotive-specific touch screen buttons will populate the remote. For more information on operating your locomotive with the LEGACY system, please refer to the LEGACY section of this manual. Additional information is also found in the LEGACY System Manual, available online at www.lionel.com. . 4 Running your locomotive Note! Power your locomotive with an alternating-current (50-60Hz AC) transformer only. Powering your locomotive with a direct-current (DC) transformer, or in excess of 19 volts AC, may result in damage to sensitive electronic components. Note! Your locomotive requires Lionel or Lionel-compatible O-54 or larger track curves. TrainMaster Command Control (TMCC/Command Control) operations For operation in the TrainMaster Command Control environment, you need a TrainMaster Command Base (6-12911) and a CAB-1 Remote Controller (6-12868). Refer to your TMCC System Manual for complete information. To access all the locomotive's features, you must operate in the LEGACY environment, as discussed on the previous page. Your commands are sent by the CAB-1 Remote Controller to the Command Base, which translates the command into digital code. That code is sent through the outside rails to your locomotive, which will not respond until it recognizes its unique ID#. TrainMaster Command Control gives you the power to operate multiple Command-equipped locomotives on the same track at the same time. 1. Turn off track power, and then plug in the Command Base and connect it to the track. 2. Place your locomotive and tender on the track and connect the drawbar as shown in Figure 1 on page 4. 3. Increase track voltage to full power (no more than 19 volts AC). If a circuit breaker trips when you turn on the Lionel power supply, check the wheels of your locomotive to make sure they are all securely on the track. Check to make sure the track is free of all metals that may cause a short circuit. 4. Press ENG and 1 to address your locomotive with your CAB-1 Remote Controller. 5. Throttle up and move `em out. For more information, please refer to the TrainMaster Command Control operations section of this manual or the TMCC System Manual, available online at www.lionel.com. 5 Running your locomotive Conventional transformer operations Note! For Conventional operation, a Command Base must not be powered up anywhere in the area, even if it is not connected to the track. If a base is detected, your locomotive will default to Command mode. Note! Power your locomotive with an alternating-current (50-60Hz AC) transformer only. Powering your locomotive with a direct-current (DC) transformer, or in excess of 19 volts AC, may result in damage to sensitive electronic components. Note! Your locomotive requires Lionel or Lionel-compatible O-54 or larger track curves. 1. With track power off, place your locomotive and tender on the track. Connect the drawbar as shown in Figure 1 on page 4. 2. Power up the track. If a circuit breaker trips when you turn on the Lionel power supply, check the wheels of your locomotive to make sure they are all securely on the track. Check to make sure the track is free of all metals that may cause a short circuit. 3. Move `em out! When the locomotive's headlight illuminates and the LEGACY RailSounds sound system starts, press the DIRECTION button on your transformer to sequence your locomotive through the repeating pattern of operations: neutral, forward, neutral, reverse, neutral, and so on. You may also briefly turn off track power to advance the locomotive to the next operating state. Adjust the throttle until your locomotive moves at your desired speed. Note! When placing your locomotive on your layout for the first time and after power interruptions lasting longer than five seconds, it will start out in neutral. We recommend that you operate your LEGACY locomotive with The Odyssey II Speed Control System turned on. You may choose to operate your locomotive without speed control by placing the OdysseyII Speed Control System switch to the NO ODY (OFF) position. See Figure 6 on page 8 for the location of this switch. Use the Whistle and BELL buttons on your transformer to activate those features. Adjust the volume using the volume control knob, which is located under the hatch on the deck of the tender. Refer to Figure 4 on page 7. For more information, please refer to the Conventional transformer operations section of this manual. 6 Locomotive basics Tender volume control location The RailSounds volume control is concealed on the tender deck as illustration in Figure 4 below. Lift the hatch open and then rotate the volume control to adjust the volume or silence the sounds. TOP OF TENDER Figure 4. Volume control location VOLUME CONTROL KNOB Adding fluid to your locomotive's smoke generator Your locomotive is equipped with a smoke generator that produces safe, clean, white smoke during operation. The smoke generator for this locomotive supplies both the stack and whistle effects. A reservoir beneath the stack contains the fluid and wich which, once saturated, supplies the heating elements with the right amount of fluid. Load smoke only into the dual main smoke stack. DO NOT add fluid to the whistle smoke hole! When adding fluid DO NOT EXCEED 20 DROPS as this can cause your smoke unit to become oversaturated allowing leakage onto the electronics. Note that operating your locomotive's smoke unit without smoke fluid will cause damage to the heating element. Add 20 drops initially to the main stack, and 10 to 20 thereafter, as required to maintain desired smoke. Figure 5. Smoke fluid locations Note! Your locomotive's smoke fluid consumption will vary depending on the smoke level setting you have selected and the number of times you blow the whistle. Refer to Figure 5 as you add the smoke fluid. If you prefer to operate your locomotive without smoke, locate the smoke unit switch on the underside of the locomotive and slide it to the OFF position. Refer to Figure 6 on page 9 for the location of the switch. This single switch controls both the stack and whistle smoke. Note! For best performance, we recommend using only 6-37841 Lionel Premium Smoke Fluid. 7 Locomotive basics Locomotive switch locations The functions of your locomotive's switches are outlined below. Refer to Figure 6 for the location of the switches. The instructions below are specific to this particular locomotive; note that available features (and switches) may differ from other locomotives and sets. Smoke Unit Switch Used to turn the smoke unit on and off. This switch is "read" by your engine at start-up only. Switching it after start-up will have no effect. This switch controls both the stack and whistle smoke. Program / Run Switch Used to assign an ID# and reprogram the locomotive in LEGACY and Command operation when the switch is in the PROG position. Also used to "lock" your locomotive in a single direction, or neutral, in conventional operation when the switch is placed in the PROG position. Odyssey II Speed Control System Switch Used to turn the OdysseyII Speed Control System on and off. BOTTOM OF LOCOMOTIVE SMOKE UNIT SWITCH ODYSSEY II SWITCH PROGRAM/ RUN SWITCH Figure 6. Locomotive switch locations 8 Locomotive basics Assigning your locomotive a new ID# For operation in the LEGACY or Command Control environment, you will want to give your locomotive a unique ID#. Your locomotive will respond to commands associated with its ID# while all other units will disregard these commands. This procedure is not necessary for conventional (non-Command) operation. 1. Slide the program run switch on your locomotive to the PROG position. See Figure 6 on page 8. 2. Place the locomotive on the track. 3. Connect the Command Base and plug it in. 4. Power up the track. 5. Press ENG on the CAB-1 or CAB-2 remote. 6. Enter the unique ID#. Choose any number from 1 to 98 that has not been assigned to another locomotive (ENG). We recommend using a part of your locomotive's road number. Note! All LEGACY locomotives respond to ENG 99. We recommend that you reserve ID# 99 as a "universal" ID#. 7. Press SET. The locomotive's whistle will sound, or the headlights will flash if the RailSounds sound system is off. 8. Slide the program run switch back to the RUN position. The locomotive's ID# has been set. Be sure to record the new ID# for your reference. 9 LEGACY Control System operations LEGACYTM Control System Engine Memory Module This unique Engine Memory Module contains the specific system information and options for your new Lionel® LEGACYTM Control System-equipped locomotive. After you have programmed your locomotive's new address following the instructions included in this manual, follow these instructions to load this information from the Module to the LEGACY Control System via your CAB-2 Remote Controller. This is a step that you perform only once. Note! LCS SensorTrackTM (6-81294) can also be used to perform this process. To upload the information from the locomotive to the cab, simply run the locomotive across the SensorTrackTM. Neither the orange module nor any further programming is required. All of the information is now loaded in your CAB-2. 1. Using your CAB-2 Remote Controller, address your Lionel LEGACY Control System-equipped locomotive with its engine ID#. 2. Press INFO. 3. Insert the Engine Memory Module into the CAB-2 Remote Controller. 4. Press LOAD MODULE. 5. Verify that the Engine Memory Module information is correct for your selected engine. If the information is correct, press YES to finish the download process for your engine. 6. An ENGINE DATA LOADED message will be displayed. Remove the Engine Memory Module. 7. Press the red CTC button to return to your operating screen. Power your locomotive with an alternating-current (50-60Hz AC) transformer only. Powering your locomotive with a direct-current (DC) transformer, or in excess of 19 volts AC, may result in damage to sensitive electronic components. Refer to your LEGACY Control System Operations manual to learn how to operate your locomotive in the LEGACY Control System environment. 10 LEGACY Control System operations The LEGACY CAB-2 Remote Controller Main Display Displays real-time information about your railroad system. Displays real-time feedback of operation. Scroll Button Navigates through the entire list of Engines, Trains, Switches, etc. Select Button Performs addressing by 3-4 digit road number. Touch Screen KeyPad A group of touch sensitive keys with icons for each function. These keys serve many purposes and their icons change accordingly. Train Brake Slider This slider is used to increase or decrease the amount of Train Brake affecting the engine or train. Train Link Button Quick select of Train-Link devices (LEGACY Control System Version 1.3) AUX-1/Thru Button Press to view the Control Panel while operating. Controls switch direction. Emergency Halt Button Stops everything on layout; also stops recording playback. AUX-2/Out Button Controls switch direction. Toggles all lights on/off, except lights that are wired to track power. Record Button Used to record and play back events. Velocity Throttle Throttle control over engines, also used to navigate thru info/options. Set Button Used to set Engine address and for programming. 11 Info Button Used to enter/view the info/options of selected components. CTC Button Press and hold to turn your remote on and off. Tap this button to enter the remote and base options. Tap it again to return to the main screen. Soft Keys These keys directly correlate to the 5 selection boxes located at the bottom of the main display. These are also used in the info/option menus to select options. Warning Sound Controller Warning Bell and Variable Whistle control. Pull down to sound Whistle. Push up and release to trigger Warning Bell. Multi Controller Boost, Brake, and Direction control. Rock forward for Boost, rock backward for engine brake, and press down for direction change. Click-hold-and rock for absolute direction selection. Front & Rear Coupler Buttons Fire couplers. Feedback Button Toggle ON/OFF the vibration feedback feature in the CAB-2 Remote. Official R.R. Speed Control Bar Toggles the touchscreen display of R.R. preset speeds and control panel. Low, Medium, High Momentum Buttons Used to select the desired momentum of your addressed engine/train/accessory. LEGACY Control System operations Note! This section is a brief overview of the LEGACY Control System. For a more in-depth explanation of the LEGACY Control System features, please see your LEGACY Control System Operations Manual, available online at www.lionel.com. The Velocity Throttle The Velocity Throttle (the red rotary knob on the bottom of your Lionel remote) is used to start your engine moving, slow it down or speed it up. Use it simply by turning it clockwise (speed up) or counter-clockwise (slow down). The Multi-Controller Direction The direction of your engine toggles between forward and reverse at the touch of the Multi-Controller. Press the center of the Multi-Controller once, and your engine's lights will change directions and the engine will stop until you throttle up again in the new direction. Boost & Brake Boost and brake give you another way to control the speed of your train. Boost gives your loco a temporary increase in tractive power, and returns to the previous speed when you release the control, while the brake command slows you down more quickly than the Velocity Throttle alone. The Train Brake Slider The Train Brake is used to slow down and limit the top speed of your train by adding a load. The more the Train Brake is applied by pulling the Train Brake Slider down, the more laboring is heard from the engine. Eventually Train Brake application will slow down the train and it is even possible to stop a train by pulling the Train Brake Slider all the way down. If your smoke unit is turned on, you'll also see more smoke as the slider is pulled down. 12 LEGACY Control System operations Warning Sound Controller Warning sounds are an important part of Lionel Railroading. Your Lionel Legacy Control System equipped engines have a real-time variable "quilling" whistle. Blow the whistle by pulling down on the Warning Sound Controller. Notice the difference in intensity of the whistle sound. Note that the Whistle Smoke effect is also activated. See page 7 to add smoke fluid. Strike the bell once by pushing the Warning Sound Controller up and releasing quickly. To activate continuous bell sounds, push the Warning Sound Controller up and hold it for 1.5 seconds. To discontinue the bell sounds, push and hold the Warning Sound Controller up until the bell stops. The Speed Bar The Speed Bar is used to select a new touch-screen Icon Control set. This set of touch-screen keys is used to select prototypical preset speeds. The speed of the engine changes with each press and release of a different Preset Speed key. · Tap a key, and your locomotive will immediately begin moving to that speed. · Press and hold a key, and you'll hear the dispatcher radio the engineer and order him to move to that speed. · If you hold the key until the dialog is finished, the engineer will indicate that he is "increasing to...", "slowing to...", or "we are at..." the command speed. You can also use the Velocity Throttle and other action controls in this mode and continue to use Preset speeds at the same time. Press AUX1 to leave the Preset speed mode and return to the Standard Control Panel. Press the speed bar to toggle between the Speed Control Panel and the Standard Control Panel. 13 LEGACY Control System operations EFX Trim and EFX Bar Graph Sound and smoke effects of the engine can be trimmed higher or lower depending on your operating preference. Pressing the EFX up button will make the engine sound like it is working harder and will also increase the smoke output (if the smoke unit is turned on). Similarly, the EFX down button will decrease the laboring sound of the engine and smoke. A RESET command will return the EFX trim to its default setting. Notice that the current EFX level is displayed on the remote as a bar graph inside the soft key to the left of the ROLL button. The height of this graph varies with the EFX keys, throttle and train brake adjustments. Leaving the Preset Speed Screen Use the Speed Bar to leave the Speed Panel and return to the Control panel. Press the Speed Bar to toggle between the Speed Control Panel and the Standard Control Panel. 14 LEGACY RailSounds Sound System operations LEGACY RailSounds sound system Volume UP Raises the overall master volume of the LEGACY RailSounds sound system. To independently adjust the level of the background sounds only (e.g., the chuffing sounds and steam hiss), tap AUX1 and then this key. CrewTalk Engineer begins radio dialog, dispatcher replies. Water Injector/Water Tower When the engine is in motion, plays the sound of water flowing from the tender to the boiler. When the engine is stopped, plays the sound of the water tower refilling the tender. RailSounds Shutdown Activates the LEGACY RailSounds sound system shutdown sequence when stopped. Emergency Stop Activates the emergency stop feature while in motion. (Icon will change as the state of the locomotive changes). Volume DOWN Lowers the overall master volume of the LEGACY RailSounds sound system. To independently adjust the level of the background sounds only (e.g., chuffing sounds and steam hiss), tap AUX1 and then this key. Volume settings are retaining when track power is turned off. Stops and resets the locomotive Resets the locomotives direction to forward. Press and hold to activate a fueling sequence. Fueling sounds. TowerCom Dispatcher begins radio dialog, engineer replies. When adjusting the overall volume, you'll hear a single bell hit that gets louder or softer with each volume adjustment. When the volume is at maximum, additional button presses have no effect and won't play the bell. When adjusting the background sounds (AUX1, then a volume key) you'll hear the volume change without a single bell hit. 15 LEGACY RailSounds Sound System operations LEGACY RailSounds Sequence Control Your LEGACY-equipped locomotive features Sequence Control. Based on the movement and speed of the locomotive, Sequence Control automatically plays the sound effects of an entire trip, from departure to destination, while you run your locomotive. Prototypical whistle signals, bell, and radio chatter are added automatically as you spin your throttle--no need to memorize a sequence of button presses. To activate the Sequence Control feature, press and hold the AUX1 button for three seconds. You'll hear a unique bell/whistle signal, indicating that Sequence Control is now enabled. Release the AUX1 key when you hear the sound. Now, radio chatter, air brake release, and warning signals will play automatically as you move out, reach cruising speed, and then decelerate for arrival, as illustrated in Figure 7. Plus, you can still activate CrewTalk communication and TowerCom announcements using your remote. To discontinue Sequence Control, you must tap AUX1, and then tap the 0 key or the RESET button. Cycling track power off and back on also turns of Sequence Control mode. Note! During sequence control mode operation, speed step 1 is used to trigger departure effects such as air brake release and departure whistle. Therefore your engine will not begin moving until speed step 2 and the Roll Mode button will bring your engine to a stop while Sequence Control mode is enabled. For the most realistic operation, medium or high momentum is recommended when using Sequence Control. SEQUENCE CONTROL ENABLED (hold AUX1 for 3 seconds) - Ding-dingtoot! Automatic Sequence Control The actual dialog will vary. AT A STOP, after a long pause - "Dispatcher, we have a clear signal."/ "Roger that." THROTTLE UP TO STEP 1 - Air brakes release, RPMs up, departure whistle. THROTTLE UP TO STEP 2+ - Bell on. "Train is moving."/"Copy.". 1/8 THROTTLE Bell off. 1/3 THROTTLE Whistle signal (in transit.). STOP - Bell off. "We are in position."/ "Copy.". SLOW BELOW 1/8 THROTTLE Bell on. SLOW - BELOW 1/3 THROTTLE - Whistle arrival signal. "We are arriving,"/ "Roger." 3/4 THROTTLE - Crossing signal "We are at maximum authorized speed.". Figure 7. LEGACY RailSounds automatic Sequence Control 16 LEGACY Control System operations CrewTalk dialog and TowerCom announcements in the LEGACY environment In addition to the automatic triggering of dialog via Sequence Control mode operation (see the previous section), you may control the dialog manually. CrewTalk dialog and TowerCom announcements feature a variety of brief radio conversations between the engineer and dispatcher. CrewTalk dialog is an engineer-initiated radio conversation with the dispatcher. TowerCom announcements are a dispatcher-initiated radio conversation with the engineer. Be sure to listen for the different combinations of words and phrases that comprise these exchanges. Refer to Table 1 below for the dialog commands. The dialog in the table provides examples of the conversations you can trigger. The actual dialog will vary. Locomotive Stopped Moving Commands AUX1, 2 AUX1, 7 2 7 5 or AUX1, 5 AUX1, 0 3 2 2 AUX1, 2 7 or AUX1, 7* 5 or AUX1, 5 Example dialog Crew: Ask To Depart Tower: Deny Departure Tower: Ask To Standby Crew: Acknowledge Crew: Ask To Depart Tower: Approve Departure Tower: Approve Departure Crew: Acknowledge Crew: Shutdown Announcement Shutdown sequence Held 3 seconds. Coal loading sounds. Crew: Coal is full. Water loading sounds. Crew: Water is full. Recent departure. Crew: Train is underway Tower: Acknowledge Crew: Are we clear ahead? Tower: Acknowledge Crew: Report engine status Tower: Clear in-bound Crew: Acknowledge Tower: Emergency stop Crew: Acknowledge *Activating 7 or AUX1, 7 while the locomotive is in motion enables an arrival conversation for 30 seconds. If the train stops within this time, pressing 2 will play this special conversation. Table 1. LEGACY Remote Controller dialog commands 17 LEGACY RailSounds Sound System operations LEGACY RailSounds sound system dialog on a round trip Refer to Figure 8 for a sample dialog script for manually controlled dialog on the locomotive's round trip using the numeric keypad. See page 16 for the automatic Sequence Control. Locomotive STOPPED The actual dialog will vary. AUX1, 2 - "Are we clear?"/" No, stand by." 2 - "Can we go yet?"/"Yes, you are clear." 5 or AUX1, 5 - Crew shutdown announcement. Shutdown sequence. AUX1, 7 - "Stand by." 7 - "You are clear." Locomotive IN MOTION The actual dialog will vary. RECENT DEPARTURE 2 - "Train is underway."/"Roger, you are clear." 2 - "Still clear ahead?"/ "Roger, you are clear." AUX1, 2 - Crew reports coal or water levels and current speed. 5 or AUX1, 5 Emergency stop. AUX1, 7 - "You are clear inbound." 7 - "All clear ahead." Figure 8. LEGACY RailSounds sound system dialog on a round trip 18 TrainMaster Command Control operations CAB-1 Remote Controller commands The CAB-1 Remote Controller commands are detailed below. The corresponding RailSounds sound system effects are in bold italic type. Releases the ElectroCoupler on the rear of the tender. Coupler release sound. Activates the numeric keypad. Short steam release sound. Controls switch direction. Toggles all lights on/off, except lights that are wired to track power. Accelerates the locomotive with a clockwise rotation. Decelerates the locomotive with a counter-clockwise rotation. Speed-dependent chuffing sounds. DynaChuff dynamic chuffing effect. Activates the locomotive's whistle. Release the button to discontinue the sound. Whistle sound with steam effect. Toggles the bell sound on and off. Bell sound. Changes the locomotive's direction. The locomotive decelerates to a stop and continues in the opposite direction when you increase the throttle. Air release sound. Increases the locomotive's speed while the button is pressed. Release the button to return to the initial speed. Labored chuff. Decreases the locomotive's speed while the button is pressed. Squealing brake sounds. Shuts down all PowerMasters on your railroad. Stops all TrainMaster Command Control-equipped locomotives in operation. Use HALT only in emergency situations. SET L M H Odyssey II Momentum L 32 speed steps with low momentum M 100 speed steps with low momentum H 100 speed steps with medium momentum 19 TrainMaster Command Control operations CAB-1 Remote Controller numeric keypad commands When you press the AUX1 button on your CAB-1 Remote Controller, you turn the numeric keypad into ten command buttons. After you press the AUX1 button, you will be able to press any numbered button until you address a different product. The corresponding RailSounds sound system effects are in italic type. Stops and resets the locomotive. Resets the locomotive's direction to forward. Your locomotive keeps track of its coal and water levels. Higher engine speeds and/or heavy labor will use fuel at a faster rate. Like a prototypical steam locomotive, water is consumed at a faster rate than coal. To add both coal and water, perform a "long reset." Press and hold AUX1, 0 for at least three seconds. You will hear the sounds of coal pouring into the tender as long as you hold the button. When you release the button, the sounds will stop and the engineer will confirm that the tank is full. Refueling sequence. Raises the overall master volume of the LEGACY RailSounds sound system. To independently adjust the level of the background sounds only (e.g., the chuffing and steam hiss), tap AUX1 and then this key. Sound volume increases. When adjusting the overall volume, you'll hear a single bell hit that gets louder or softer with each volume adjustment. When the volume is at maximum, additional button presses have no effect and won't play the bell. When adjusting the background sounds (AUX1, then a volume key) you'll hear the volume change without a single bell hit. Engineer begins radio dialog, dispatcher replies (see page 17). To hear the engineer say the current level of coal or water and current speed, press AUX1, 2 or AUX1, CrewTalk while the engine is in motion. CrewTalk communication. In motion, plays the sound of the injector transferring water from the tender to the boiler. At a stop, plays te sound of a water tower spigot arm lowering, then water gushing from the tower into the tender, which also "refills" the virtual water level in the tender and plays a confirming radio dialog. Water injector/water tower sounds. 20 TrainMaster Command Control operations CAB-1 Remote Controller numeric keypad commands (continued) Lowers the overall master volume of the LEGACY RailSounds sound system. To independently adjust the level of the background sounds only (e.g., chuffing and steam hiss), tap AUX1 and then this key. Volume settings are retaining when track power is turned off. Sound volume decreases. Activates the LEGACY RailSounds sound system shutdown sequence when stopped. Activates the emergency stop feature while in motion. Note that, in the shutdown sequence, the smoke unit will turn off if it was already on. Triggers the Blowdown sound. r Dispatcher begins radio dialog, engineer replies (see page 17). TowerCom announcement. Turns off the smoke units. Let-off sound. Turns on the smoke units if the smoke units' switches are in the ON position. Be sure to add smoke fluid before turning on the smoke unit to prevent damage to your locomotive. Let-off sound. Note! AUX1, 8 and 9 function only if the locomotive's smoke unit switch is in the ON position. 21 Conventional transformer operations Using the LEGACY RailSounds sound system in the conventional environment When you first power up your locomotive, you will hear the sounds of the locomotive at rest. As the locomotive moves, the RPM sounds automatically increase with the locomotive's speed. In the conventional environment, the whistle and bell sounds are activated by your transformer controls, if so equipped. To adjust the volume, use the volume control knob. Refer to Figure 6 on page 8 for the location of the volume control knob. In the conventional environment, you will experience several features of the LEGACY RailSounds sound system. · DynaChuff. Your locomotive's speed automatically determines the character of the chuffing sounds. At low speeds, the chuffing sounds are longer. When you highball down the mainline, the chuffing intensity becomes more percussive. · MultiWhistle. A different whistle sound at different speeds. · Mechanical bell. Press BELL on your transformer to begin the effect, then press BELL a second time to discontinue the effect. · CrewTalk dialog and TowerCom announcements. These brief conversations between the train crew and the tower are triggered by short whistle blasts. Activating the CrewTalk dialog and TowerCom announcements In the conventional environment, CrewTalk dialog and TowerCom announcements are triggered by short whistle blasts and vary with the state of the locomotive. · If the locomotive has been stopped for less than 15 seconds, a short whistle blast triggers a "please standby" dialog. · If the locomotive has been stopped for longer than 15 seconds, a short whistle blast triggers a "cleared outbound" dialog. · If the locomotive has started moving within the last seven seconds, a short whistle blast will trigger a "train is underway" dialog. · If the locomotive has been moving for more than seven seconds, a short whistle blast will trigger a "are we clear?" dialog. 22 Conventional transformer operations Locking your locomotive into a single direction When the Command reverse unit switch is in the RUN position, your locomotive sequences through a repeating pattern of operations: forward, neutral, reverse, neutral, and so on. To "lock" your locomotive into a single direction (for example, to operate in forward only), you can deactivate the Command reverse unit's sequencing function. 1. Use your transformer's DIRECTION button or interruptions in track power to get your locomotive moving slowly in the desired direction or into neutral. 2. Slide the Command reverse unit switch to the PROG position. At this point, the locomotive is "locked" into your chosen direction. See Figure 6 on page 8 for the location of this switch. To restore the forward-neutral-reverse sequence, just slide the Command reverse unit switch back to the RUN position. Note! Because of the way that speed control operates in conventional mode, you will notice a slight delay between adjusting your transformer throttle and the change in the speed of your locomotive. If you desire instantaneous response to throttle changes, turn off the Odyssey II Speed Control system using the Odyssey II Speed Control switch (see Figure 6 on page 9.) 23 Odyssey II Speed Control system operations Odyssey II Speed Control system operations The Odyssey II Speed Control system is "cruise control" for your locomotive. Once the speed control is set, your locomotive will maintain a constant speed, no matter what load is placed on the locomotive or what grades you have on your layout. The Odyssey II Speed Control system also allows for extremely slow movement that will amaze any scale enthusiast. Odyssey II Speed Control System LEGACY Control operation In LEGACY Control System CAB-2 mode, Odyssey II Speed Control system provides 0-199 speed steps. For a more in-depth explanation of the LEGACY Control System features, please see your LEGACY Control System operations manual, available online at www.lionel.com. Odyssey II Speed Control system TrainMaster Command Control operation When the Odyssey II Speed Control system is activated, changes in the speed of the locomotive will correspond to each signal from the Command Base. For example, when you address the locomotive and slowly turn the throttle knob, the first flash of the red light on the Command Base corresponds to the first speed step, which is the slowest speed of the locomotive. The locomotive will maintain that speed until you increase or decrease the throttle. In TrainMaster Command Control CAB-1 mode, Odyssey II Speed Control System now provides selectable resolution and momentum. See the momentum settings listed on page 19. Odyssey II Speed Control system conventional transformer operation The Odyssey II Speed Control system is automatically operational when you operate your locomotive in conventional (non-Command Control) mode, as long as the Odyssey II Speed Control system switch is in the ODY position (see Figure 6 on page 8). This means that your locomotive will maintain a constant speed, compensating for grades, loads, and turns. Simply use your transformer's throttle to adjust the speed of your locomotive. Note! Because of the way that speed control operates in conventional mode, you will notice a slight delay between adjusting your transformer throttle and the change in the speed of your locomotive. If you desire instantaneous response to throttle changes, turn off the Odyssey II Speed Control system using the Odyssey II Speed Control switch (see Figure 6 on page 8). 24 Maintaining and servicing your locomotive Reprogramming your locomotive to restore features If your locomotive is unresponsive to your commands in the Command Control environment, we recommend that you follow this procedure to reset your locomotive. All factory default settings will be restored when you reprogram the locomotive. 1. Slide the program run switch to the PROG position. 2. Plug in and connect your LEGACY Base. 3. Place your locomotive on the track, then power up the track. 4. Press ENG and enter the locomotive's ID#. 5. Press SET. 6. Turn off track power and wait ten seconds. 7. Slide the program run switch back to the RUN position. At this point, your locomotive has been reset. Restore power to the track and operate the locomotive as usual. Be sure to use the ID# entered in Step 4. 25 Maintaining and servicing your locomotive Lubricating your locomotive Help your Lionel locomotive lead a long and productive life on your railroad by maintaining it properly. To keep your locomotive lubricated, we recommend that you purchase a Lionel Lubrication and Maintenance Kit (6-62927), available from your authorized Lionel dealer. When you find that the lubrication points illustrated in Figure 9 appear dry, lubricate your locomotive after you have removed any accumulated dirt and dust. There are two basic rules to keep in mind when you are lubricating your locomotive: use only a small amount of lubrication and avoid getting grease or oil on your locomotive's wheels, roller pick-ups, or the track. BOTTOM OF LOCOMOTIVE OIL (SPARINGLY) OIL (SPARINGLY) OIL (SPARINGLY) Figure 9. Lubrication points OIL (SPARINGLY) 26 Maintaining and servicing your locomotive Servicing your locomotive's LEDs Note! If the locomotive is powered up and the lights are not on, check that the AUX2 command was not used to turn the lamps off. Your locomotive is illuminated by several LEDs that are expected to last for the life of the locomotive. The LED's are not user serviceable. If service is required, we recommend that you have your locomotive serviced at a Lionel Factory Trained Authorized Service Station. Maintaining you locomotive's handrail antennas The handrails on your locomotive are the antennas that receive the Radio Signal communication from the Command Base. For optimum reception, the handrails have been insulated from the die-cast body. Please handle the locomotive carefully to avoid handrail damage. The handrails should not touch the locomotive body. If your locomotive appears to have problems receiving communications from the Command Base, be sure that the ends of the handrails are insulated from the body with either an insulating washer or plastic handrail stanchion. Replacing the traction tires Your locomotive is equipped with traction tires. This means that two of the drive wheels are fitted with rubber traction tires to enhance tractive effort so your locomotive can pull many cars at once. Lionel has provided extra traction tires to replace the installed traction tires if they ever wear out. The traction tires are replaced by unscrewing the drive rod screws using the supplied wrench. See Figure 10. Slip off the old traction tire and remove it from under the drive rod. Place the new traction tire (Lionel part no. 6000222108) on the wheel and re-tighten the drive rod screw. Figure 10. Replacing traction tires 27 Maintaining and servicing your locomotive Locomotive Diagnostics Your locomotive includes built-in diagnostics to monitor the condition of the main drive motor and smoke system. If a problem is detected, the locomotive's cab light will blink a diagnostic code. If you see the light inside the cab flashing, press RESET (for LEGACY operation), 0 (for TMCC operation), or DIRECTION/power interruption (for conventional operation to attempt to clear the problem. The locomotive will immediately check itself again. If the problem persists, the cab light will blink the code again. Note that smoke-related errors can be reset a maximum of three times. On the third try, if the problem still persists, the smoke unit will be shut down. After reaching the three-cycle limit, the power must be cycled (turn off and on) and then you may try to reset three more times. If the problem persists, it must be returned to a local Factory Trained Authorized Lionel Service Station, or contact Lionel Customer Service for repair. The single SMOKE switch controls both the stack and whistle smoke. Note! Turning the smoke unit switch to the off position will disable diagnostic checks of the smoke system. Number of Blinks 1 2 3 4 5 Diagnostic Code Description Main drive motor stalled. Smoke 1 element problem. Smoke 1 fan problem. Smoke 2 element problem. Smoke 2 fan problem. 28 Notes 29 Lionel Limited Warranty Policy & Service This Lionel product, including all mechanical and electrical components, moving parts, motors and structural components, with the exception of LIGHT BULBS, LED's & TRACTION TIRES are warranted to the original owner-purchaser for a period of one year from the original date of purchase against original defects in materials or workmanship when purchased through a Lionel Authorized Retailer*. This warranty does NOT cover the following: · Normal wear and tear · Light bulbs or LED's · Defects appearing in the course of commercial use · Damage resulting from abuse/misuse of the product Transfer of this product by the original owner-purchaser to another person voids this warranty in its entirety. Modification of this product in any way; visually, mechanically or electronically, voids the warranty in its entirety. Any warranted product which is defective in original materials or workmanship and is delivered by the original owner-purchaser (this warranty is non-transferrable) to Lionel LLC or any Lionel Authorized Service Station MUST be accompanied by the original receipt for purchase (or copy) from an Authorized Lionel Retailer*, will at the discretion of Lionel LLC, be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a suitable replacement is not available, Lionel will offer to replace the product with a comparable model (determined by Lionel LLC), if available. In the event a comparable model is not available the customer will be refunded the original purchase price (requires proof of purchase from the Authorized Lionel Retailer* it was originally purchased). Any products on which warranty service is sought must be sent freight or postage prepaid (Lionel will refuse any package when postage is due). Transportation and shipping charges are not covered as part of this warranty. NOTE: Products that require service that do not have a receipt from an LIONEL AUTHORIZED RETAILER* will be required to pay for all parts required to repair the product (labor will not incur a charge) providing the product is not older than 3 years from date of manufacture and is within 1 year from date of purchase. A copy of the original sales receipt is required. In no event shall Lionel LLC be held liable for incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion may not apply to you. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Instructions for Obtaining Service If service for this Lionel LLC product is required; bring the item, along with your DATED sales receipt and completed warranty information (at the bottom of this page) to the nearest Lionel Authorized Service Station. Your nearest Lionel Service Station can be found by calling 1-800-4-LIONEL or by accessing the website at www.lionel.com. If you prefer to send your Lionel product directly to Lionel, for repair you must FIRST call 586-949-4100 extension 2 or write to Lionel Customer Service, 6000 Victory Lane, Concord, NC 28027. Please have the 6-digit Lionel product number, the date of original purchase, the dealer where the item was purchased and what seems to be the problem. You will receive a return authorization (RA) number to ensure your merchandise will be properly tracked and handled upon receipt at Lionel LLC. Once you have your Return Authorization (RA) number, make sure the item is packed in its original Styrofoam inner container which is placed inside the original outer display box (this will help prevent damage during shipping and handling). This shipment MUST be prepaid and we recommend that it be insured with the carrier of your choice. Please make sure you have followed all of the above instructions carefully before returning any merchandise for service. You may choose to have your product repaired by one of Lionel LLC's Authorized Service Stations after its warranty has expired. A reasonable service fee should be expected once the product warranty has expired. Warranty Information Please complete the information below and keep it, along with your DATED ORIGINAL SALES RECEIPT. You MUST present this form AND your DATED SALES RECEIPT when requesting warranty service. *A complete listing of Lionel Authorized retailers can be found by calling 1-800-4-LIONEL or by visiting our website at www.lionel.com. Products that are more than 3 years old, from date of manufacture, are not applicable for warranty coverage, even if they have never been sold prior to this date. (Under no circumstance shall any components or labor be provided free of charge.) Name _________________________________________________________________________ Address ________________________________________________________________________ Place of Purchase _________________________________________________________________ Date of Purchase __________________________________________________________________ Product Number __________________________________________________________________ Product Description ________________________________________________________________ ©2014 LIONEL L.L.C., CONCORD, NC 28027 UNITED STATES OF AMERICA PRINTED IN CHINAAdobe PDF Library 10.0.1 Adobe InDesign CS6 (Macintosh)