to WiFi Power on device ,WiFi connected Device power off This device can support remote viewing on both IOS and Android devices. 1).IOS:Log-in to the Apple “APP store” and search for “Yieye”. 2).Android:log-in to Google “Play store” and search for “Yieye”. You may also scan the QR code below that corresponds to your mobile operating
User Manual Dummy Smoke Detector Security Camera Please read user manual carefully before use Emai: care@fuvision.net YOU NEED TO KNOW BEFORE SETUP: 1. Make sure you are using 2.4GHz wireless network, not 5GHz 2. Make sure the RED LED light is blinking slowly when power on. if not, please reset the camera. 3. Make sure your camera and wifi router are not far away. 4. Make sure your phone is close to the camera when configuring. 5. Go to Wi-Fi setting of your smartphone to see if camera ID like YIEYE-XXXXX-XXXXX is matched with the one we put the sticker on the device 6. Please do not connect camera ID YIEYE-XXXXX-XXXXX directly from Wi-Fi setting of your smartphone 7. Make sure your Wi-Fi SSID do not contain any symbol or special characters. 8. Make sure your camera is charged up to 24 hours for the first time use. Key Benefits: 100% Wire-Free: Free Of Ugly cords and wiring hassles Night Vision:See what's happening even in the dark HD Quality:Enjoy amazingly sharp 1080P live video WiFi Wi-Fi:802.11 b/g/n wireless network Micro SD :Memory SD Card max up to 64GB Not included), 8GB 400 days videos Built-in 6000mA battery: Battery supports to standby 6-8 months Motion Alerts: Receive push notifications if anything moves Fast Response:1 second enable recording even at standby mode Low Power Consumption: 200uA at standby mode 1.Product Structure Infrared LED Light Light Dependent Resistor Off On PIR Sensor Camera Charging Port Indicator Power On/Off Button Reset Button Micro SD Slot 2.Package Content Main Device User Manual Screw USB Cable 3.Installation 9.8ft(300cm) 6.5ft(200cm) 3.2ft (100cm) 6.5ft (200cm) 9.8ft (300cm) 13.1ft (400cm) 3.2ft(100cm) 16.4ft (500cm) 4.Specification Camera Built-in image sensor 1/3" progressive CMOS sensor Sensor sensitivity 1.0 Lux Focal Length 0.6 mm or 2.8mm(For Selected Model) Angle of View 60° or 128° (For Selected Model) Video Spec Algorithm H.264, JPEG File Format AVI,JPEG Video recording mode PIR motion recording mode Recording capability 1920x1080P Frame rate Up to 15 fps Night vision Up to 5 meters (16.4ft) PIR detect distance 5 meters (16.4ft) PIR boots up In 1 seconds Video file length 10-60 seconds option Audio Microphone Disabled Speaker Not available WiFi Spec WIFI Built-in WiFi Module(IEEE 802.11b/g/n) Storage Memory type Micro SD Card (Support SDHC max=64GB,not included) Misc Date/Time Table YYYY/MM/DD, HH:MM:SS Snapshot Recording Power Power Input DC 5V Power Consumption 200uA in standby,190mA-220mA in recording(WiFi), 590mA-650ma mA WiFi +Night vision Charging Time 24 hours(5V 2A) Battery Input DC 3.7V/6000 mA high polymers battery Battery Lifetime 6-8 months in PIR standby Recording time 400 days@1280*720p (8GB micro SD card not included),base on 10 detecting files per day Push alarm notification Motion detected alarm,Low battery Product Dimension 12.8*10*4.6cm(5x3.9x1.8INCH) Others App name Yieye Mobile surveillance iPhone, Android Remote access Yes View Angle Bottom or Side view Indoor/outdoor usage Indoor 5.Charging the battery This unit has a built-in rechargeable lithium battery. When using the unit for the first time,please charge it 24 hours. Open the device (Picture#1),make the USB power cable connected with charger seat and insert the charger into the electrical outlet (Picture #2). The Green LED indicator will be blinking slowly,until charge 24 hours fully. (Note:There is no LED indicator displayed during charging for the first 20 minutes when battery is ran out completely. Picture #1 6.Format Memory Card There are two ways to format the memory card. 1).Format the card on computer. 2).Insert micro SD card into memory card slot. Go to Yi eye app to format. More information ,please refer to 9.5 Playback&Share Videos and Photos in user manual. 7.LED Light State Introduction No. LED Status 1 Slowly blinking green 2 Slowly blinking red within 180 seconds 3 Fast blinking green 11 times, change to solid green 10 seconds 4 Fast blinking red 5 times 5 Solid green Device Status Charging power for battery Power on device ,to be connecting to WiFi Power on device ,WiFi connected Device power off Device abnormal, press and hold the Reset button for 30 seconds, then release 8.Preparation This device can support remote viewing on both IOS and Android devices. 1).IOS:Log-in to the Apple "APP store" and search for "Yieye". 2).Android:log-in to Google "Play store" and search for "Yieye". You may also scan the QR code below that corresponds to your mobile operating system to download and install app. 9.Start using the device Wi-Fi Configuration Step 1 Place the dummy smoke detector security camera on a flat surface close to home router along with user's mobile phone, slide the ON/OFF switch to On position. Red LED blinks within 180 seconds. Off On Note:lt only support 2.4Ghz internet Wi-Fi network,no 5G network. AT&T Settings 11:50 AM Wi-Fi Wi-Fi FYX_6211_2.4G i CHOOSE A NETWORK... YIEYE-002335-SXDSP i Step 2 Wait a full 40 seconds for the device to boot up, then enter Setting on the phone, select Wi-Fi, scan and join the network of Wi-Fi router. Note: A.Please do not directly connect and join camera ID in Wi-Fi setting of your smartphone B.If there is no camera ID like YIEYE-XXXXXXXXXXX displayed, Press and hold Reset button up to 10 seconds and then release to reset the camera. i WARNING AT&T Settings 11:50 AM Wi-Fi Wi-Fi FYX_6211_2.4G i CHOOSE A NETWORK... YIEYE-002335-SXDSP i AT&T Settings 11:50 AM Wi-Fi AT&T 11:50 AM Yi Eye + AT&T 11:50 AM Back Select device type Smoke Detector Camera Step 3 Open the Yi eye APP on the phone,and click Tap to add a device. Step 4 Tap on Smoke Detector Camera as shown. AT&T 11:50 AM Back Camera Configuration Confirm whether red LED is blinking Red LED is not blinking Red LED is Blinking Slowly Add online devices Step 5 Tap on Red LED is blinking slowly. Notice: Make sure you see Red LED is blinking slowly before clicking the button of Red led is blinking, If not, please reset device AT&T 11:50 AM Step 6 Select method A,B,or C to add device. A QR Scan B C A:Scan the QR code on your device,this is the quickest way to add the camera. Yi Eye YIEYE-002335-SXDSP B:Press the icon on the lower left corner ,add the picture of QR code in your phone's photos. C. AT&T 11:50 AM Back Mannual input UID UID YIEYE-002355-SXDSR X OK Press the pencil icon on the lower right corner, and enter camera ID on your device as shown. AT&T 11:50 AM Back lnternet Wi-Fi configuration Enter Wi-Fi password 1 Wi-Fi SSID FYX_6211_2.4G Wi-Fi password 2 *********** Display password *Not support 5Ghz Wi-Fi Proceed 3 Step 7 Enter the home owner's SSID and password, then press Proceed. Notice: It do not support 5Ghz wireless network, Only 2.4Ghz wireless network! AT&T 11:50 AM Back Enter Access Password 1 2 Smart Config 3 Step 8 Enter owner's access password and keep in mind in case,then tap on Smart Config. Step 9 1.Press "Send Sound Wave" button and wait for the device indicator to turn solid green. then click Next button. if no solid green displayed, please resend AT&T 11:50 AM Back lnternet Wi-Fi configuration AT&T 11:50 AM Back lnternet Wi-Fi configuration OK OK AT&T 11:50 AM Back lnternet Wi-Fi configuration OK 2.Waiting for camera to be connected with 2.4Ghz wireless router. If fail to connect, please try it again! Note: A. Please put your smart phone to the device within 10CM. B.Turn the volume of smart-phone to maximum. C.If configuration failed: Please make sure enter correct Wi-Fi password (Note: case-sensitive and blank). Keep the environment is quiet when do the configuration. AT&T 11:50 AM Back Camera lnfo Living Room Backyard Camera Alias 123 X Save AT&T 11:50 AM Yi Eye 123 YIEYE-002335-SXDSR 2018.7.25 14:24:01 online Step 10 Name the device,tap on Save. Step 11 The photo frame camera should be online as shown. 9.1 Watch Live Video More settings Camera name Camera ID Online status Enable/Disable disturb mode Motion detection setting AT&T 11:50 AM Yi Eye 123 YIEYE-002335-SXDSR 2018.7.25 14:24:01 online Add a camera Date/Time display Delete a camera Camera settings Play SD videos AT&T 11:50 AM 1.Motion notification center 2.Videos/photos recorded in APP 3.APP version Camera name FPS Real-time Wi-Fi signal AT&T 11:50 AM 123 1272kbps 15fps 2018.7.25 14:24:01 Enable full screen Battery status Date/Time Press to speak (Not available) Press to record video (Saved in album of APP) Press to listen Take snapshot (Saved in ablum of APP) 9.2 Add Online Devices AT&T 11:50 AM Yi Eye + Step 1 + Open the Yi eye APP on the phone,and click icon on the top right corner. AT&T 11:50 AM Back Select device type Smoke Detector Camera AT&T 11:50 AM Back Camera Configuration Confirm whether red LED is blinking Step 2 Tap on Smoke Detector Camera as shown. AT&T 11:50 AM Red LED is not blinking Red LED is Blinking Slowly Add online devices Step 3 Tap on Add online devices. Step 4 A Select method A,B,or C to add online device, more information,please follow Step 6 above. QR Scan B C AT&T 11:50 AM Back Enter password New password * X Save AT&T 11:50 AM Back lnternet Wi-Fi configuration Step 5 Enter correct camera's password, select Save. Step 6 Wait few seconds as shown. AT&T 11:50 AM Back Camera lnfo Living Room Backyard Camera Alias 123 Save Step 7 X Name the device ,tap on Save .The device will be online. 9.3 Motion Detection Setting AT&T 11:50 AM Motion detection Save 1 2 AT&T 11:50 AM Motion detection 5 Save 3 4 Enable motion record 1.Slide Enable to On position 2.Tap on More setting 3.Select Sensitivity(Low/Medium/High) 4.Select video file length of motion record(10-60 seconds selectable, 10 seconds defaulted) 5.Press Save and back to the live view mode AT&T 11:50 AM Motion detection Save 1 2 AT&T 11:50 AM Motion detection Save 4 3 AT&T 5 6 Enable schedule motion record 1.Slide Enable to On position 2.Select Detection schedule setting 3.Select All with check mark icon to setup full time motion alarm 4.Tap Days icon to select which day to setup alarm (Through Monday to Sunday, multiple selection available) 5.Select time period for schedule record 6.Press Save AT&T 11:50 AM Motion detection Save Disable schedule motion record 1.Unmark All with the check icon 2.Press Save on the upper right corner and back to live view mode 9.4 Alarm Setting AT&T Yi Eye Step 1 Enable Notifications on the phone as shown AT&T 11:50 AM Motion detection Save AT&T 11:50 AM Yi Eye 123 YIEYE-002335-SXDSR 2018.7.25 14:24:01 online Step 2 Enable motion detection as shown. AT&T Step 3 Disable disturb mode. Step 4 The phone will receive notification message as shown once motion is detected. 9.5 Playback&Share Videos and Photos AT&T 11:50 AM Yi Eye 123 YIEYE-002335-SXDSR 2018.7.25 14:24:01 online AT&T 11:50 AM Back Remote playback i 1 2 3 Enter into SD card playback menu as shown. 1.Choose date 2.Tap to play video 3.Share video to friends and family members as shown. AT&T 11:50 AM Back Remote playback i1 Memory Card information 2 3 4 1. Memory card info menu 2. Enable/disable loop recording 3. SD card information 4. Proceed format SD card Share Photos 1 AT&T 11:50 AM 1 2 AT&T 11:50 AM Back Album 2 3 AT&T 11:50 AM Back Photos Edit 2018-08-17 17:00:48.jpg 2018-08-17 17:00:48.jpg 4 AT&T 11:50 AM Back 2018.7.25 14:24:01 YIEYE-002335-SXDSR_2018-08-01 17:00:50.jpg Share your favorite picture to friends and family members as shown. Share Videos 1 AT&T 11:50 AM 2 AT&T 11:50 AM Back Album 1 2 3 AT&T 11:50 AM Back Videos Edit Share your favorite video to friends and family members as shown. 9.6 Change Device Code AT&T 11:50 AM Back Change password Go to Settings in APP ,and tap on Access code, then enter the information asked(Old/New code/ Re-enter new code),and press Save. 9.7 Reset Dummy smoke detector camera can be reset in the following ways: 1).Press and hold the reset the button for 10 seconds to reset WiFi video camera and restore the factory settings after power on device. 2).Go to Settings in APP,and tap on Restore to factory setting ,then click as shown. AT&T 11:50 AM Back Restore to factory setting Restore to factory setting Note: Please wait up to 2 minutes after reset! 9.8 Change the IP connection from A internet to B internet Default the device as point 9.7,then follow point 9 to configure internet Wi-Fi. 9.9 Other Options 1.Change camera name as your demand and update the latest firmware to the camera when available. 2.Setup correct time and date stamping 3.Change the image display direction. 4.Enter correct power frequence 5.Adjust speaker and microphone volume (Speaker not available,audio disabled) 6.Restore the camera to factory default setting 7.Share Camera ID to friends and family members AT&T 11:50 AM Back 1 2 settings 3 4 5 6 7 Emai: care@fuvision.netAdobe PDF library 10.01 Adobe Illustrator CS6 (Windows)