Elite Screens Evanesce Series User Manual - User Manual - PDF Download
In-Ceiling Electric Motorized Front Projection Screen Evanesce Series User's Guide 1 Rev.122411-AS www.elitescreens.com info@elitescreens.com Important Safety & Warning Precautions Make sure to read this user's guide and follow the procedure below. Caution: The screen's Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this unit are prohibited and will void your warranty. For more information, please contact our Technical Support Department at (877) 511-1211 Ext. 604. · Please retain this user's guide for future reference. · To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the manufacturer. · Handle the unit carefully during transportation to avoid any damages. · To ensure safe and reliable operation, direct connection to a properly grounded power source is advised. · The power outlet supplying power to the unit should be close to the unit and easily accessible. · Do not install the unit on uneven or inclined surfaces. · Do not place any heavy objects over the power cord. · Position the power cord properly to avoid creating a trip obstacle. · To avoid an electrical shock or fire, due to a loose contact or short circuit, do not overload the power cord. · The internal & external parts of this unit are not end user serviceable. Do not attempt to disassemble this unit by yourself. No one except authorized technicians can open and make repairs to this unit. · Make sure the power source that this unit is connected to has a continuous power flow. · If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to avoid over heat. · Do not handle the power plug when your hands are wet or your feet are in contact with water. Do not use this unit under the following circumstances. · Disconnect the power cord under the conditions of heavy rain, wind thunder or lightning. · Avoid direct sun light, rain shower and moisture. · Keep away from fire sources and high temperature to prevent this device from overheating. · Cut off the power supply first before transportation or maintenance. · To avoid possible injury and/or an electric shock, do not attempt to use this screen if there is obvious damage or if there are any evident broken parts. · 2 Rev.122411-AS www.elitescreens.com info@elitescreens.com Installation Warning Due to various installation environments, the instructions provided in this user's guide are for reference only. Please consult a professional installation company for further installation and safety advice. The installer must insure that proper mounting hardware is used to provide adequate strength suitable for the installation. Elite Screens is not liable for any faulty installations. For Limit adjustment instructions, please contact our Technical Support Department at (877) 511-1211 Ext. 604. The Screen's Top Black Drop is already set to its maximum drop distance. There is NO extra top black drop in the roller. Please be aware of this as it will void the limitation of your warranty. Individual modifications to this product are prohibited and will void the warranty with the manufacturer. Please contact Elite Screens Customer Service for any questions. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur on a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna of the device which may be casing the interference. Increase the separation between the screen and the device's receiver. Connect the equipment into a different power outlet other than the device. Pre-Installation 1. Carefully unpack the screen. 2. Always handle the screen in a leveled position on a clean surface. 3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign particles such as dust, sawdust, and/or liquids. NOTE Regardless of the mounting method, the screen should be securely supported so that the vibration or pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure that the fasteners used are of adequate strength and suitable for the installation location. 3 Rev.122411-AS www.elitescreens.com info@elitescreens.com Accessories for Evanesce Series Please make sure all accessories listed below are included before proceeding. A. IR Remote B. RF Remote C. 3 Way Wall Switch D. IR Eye Receiver G. AAA Batteries Red+ Green- E. 12V Trigger Rev.122411-AS www.elitescreens.com F. In-Wall RJ-45 Module info@elitescreens.com H. Bubble Level 4 Control System for Evanesce Series 1. 5-12V Trigger: The built-in 5-12V trigger input allows your screen to synchronize its drop & rise with the projector's power cycle. The screen deploys when the projector powers up and will retract when the projector powers down. The 512 volt adaptor connects to your projector's trigger output via a separate cable that may or may not be provided by the manufacturer of the projector. The trigger feature will not work without an output cable from the projector, but it can be tested by connecting the Red (+) and Green (-) cable to a 9-volt battery. RJ-45 INPUT FOR 5-12V TRIGGER 5-12 VOLT TRIGGER CABLE 2. 3-Way Wall Switch: The 3-way wall switch is a wall mount control box with an up/stop/down button and plugs directly into the screen's RJ-45 input. 3. IR "Eye" Receiver: plugs directly into the screen's RJ-45 input to present a low profile line-of-sight control option for your IR remote control even in a recessed ceiling installation. 4. IR Remote Control: The Infrared functions by direct line of sight contact with a beam range of 30 feet. 5. RF Remote Control: The radio waves eliminate the need for a direct line of sight with a range of 150 feet. UP Stop Down 5 Rev.122411-AS www.elitescreens.com info@elitescreens.com 6. In-Wall RJ-45 Module: The RJ-45 Module connects to a local wall switch for UP/Down control of your screen. Please follow the picture diagram below for instructions on how to connect the accessory. Elite Screens In-Wall Switch Module ( ZIW-Module ) Ethernet (RJ45) network cable (not included) Local Wall Switch In-Wall UP/DOWN Switch Module (ZIW-Module) Elite Electric Motorized Screen Steps to attach Elite Screens Motorized Screen to your local wall switch 1. Attach Elite Screens ZIW-Module (in-wall switch module) to your local wall switch as shown in diagram above. 2. Attach an RJ-45 Ethernet cable (not included) to the ZIW-Module and the other end to the RJ-45 input on your Elite electric screen. 3. After testing the connection, place the in-wall switch module in or on the wall and wire the Ethernet cable to complete the set up. NOTE: Please be aware that Ethernet cables have length limitations so please make test before concealing the cable into the wall. 6 Rev.122411-AS www.elitescreens.com info@elitescreens.com Hardware Parts List for Evanesce Series Please make sure all parts listed below are included before proceeding with the installation. G Hardware Parts List QTY A. Case Rail Nut 4-6 B. Hex Screw 4-6 C. Hanging Bracket 2-3 D. Suspension Bar 4 E. Washer 8-10 F. Hex Nut 4-6 G. Suspension Bar J- Hook 4 Installation Instructions Please consult a professional installer. Elite Screens is not liable for faulty installations. Power 1. The Evanesce Series includes a 3-Prong Power Cord for use in a non-concealed power outlet. If your installation will be entirely concealed (including power outlet), Elite Screens strongly recommends a hardwire connection. Please refer to the image below for both 110v & 220v wiring information. 7 Rev.122411-AS www.elitescreens.com info@elitescreens.com Assembly 2. Insert the Hex Screw (B) through the Hanging Bracket's (C) screw hole and secure with the Case Rail Nut (A). Slide the Hanging Bracket (C) through the railing on top of the case. 3. Place the Suspension Bar (D) on the Hanging Bracket (C) and align with the hole as shown below. Secure the Suspension Bar (D) with the Hex Screw (B), Washer (E) and the Hex Nut (F). Install the Suspension Bars (D) to your ceiling according to their distance. D B E EF 8 Rev.122411-AS www.elitescreens.com info@elitescreens.com Optional Suspension Bar J-Hook (G) 1. Attach the Suspension Bar J- Hook (G) to the bottom of the Suspension Bar (D) and secure with the Hex Screw (B), Washer (E) and Hex Nut (F). F E E B 2. Attach the Suspension Bar J-Hook (G) to the Hanging Bracket (C) as shown in figure below. Install the Suspension Bars (D) to your ceiling according to their distance. Rev.122411-AS www.elitescreens.com info@elitescreens.com G C 9 Optional Installation (parts & hardware not included) 1. Place the Hanging Bracket (C) in the desired location on the screen's housing and measure the distance as shown below. (L = Distance) 2. Mark the location of where the screen will be installed according to the distance (L) and then secure the bolt to the ceiling. 3. Install the screen to the screw bolt as shown in the figure below. 10 Rev.122411-AS www.elitescreens.com info@elitescreens.com Evanesce Series Dimension Table *Measurement dimensions are for reference only and subject to change without notice. Note: Data Error may be ±1" 11 Rev.122411-AS www.elitescreens.com info@elitescreens.com Warranty Policy · Two (2) Year parts and labor warranty from defects in workmanship from purchase date as follows (except for refurbished units as specified below). · Three (3) Year parts and labor warranty from defects in workmanship for GEMR (Government, Educational, Military, & Religious) purchases of new product only. · Refurbished Units carry a 90-DAY parts and labor warranty. · Each party will be responsible for one way shipping during the warranty period. · A RMA (Return Merchandise Authorization) number must be issued in order to process a replacement or to authorize a return for warranty repair. Elite Screens will, at its sole option replace or repair the defective unit with a replacement *(see exceptions below) after the defective unit or parts have been received. Once the product is received, Elite Screens will send out a replacement *unit to the customer by ground service (subject to inventory availability). · Do Not Return Any Unauthorized Items to Elite Screens, as they will be refused and returned at your expense. The RMA Number must be included on the outside label of your shipping box. Our warehouse is not authorized to accept returns without an RMA number on the shipping label. · RMA Numbers are valid for 45 days from the date issued. · Missing Parts must be reported within 7 days of receipt. If reported after 7 days, the customer will be responsible for shipping and handling fees. If reported after 30 days of receipt, the customer will be responsible for cost of parts and shipping & handling fees. *A New or refurbished replacement will be send out to the customer depending on the type of purchase (new or refurbished) and based on stock availability. North America only U.S. and Canada For Warranty and Service requests, please submit an RMA/Service Form at: www.elitescreens.com/warrantysupportform Please visit this link for full Warranty information: www.elitescreens.com/warranty For Customer Service and Technical questions, please contact Elite Screens at: Telephone: (877) 511-1211 service@elitescreens.com Fax: (562) 926-8433 techsupport@elitescreens.com REMEMBER TO REGISTER YOUR PRODUCT AT: WWW.ELITESCREENS.COM 12 Rev.122411-AS www.elitescreens.com info@elitescreens.com Contact Information US & Canada Tech Support & Warranty Claim Please contact us at service@elitescreens.com or call +1 877-511-1211 #3 or fax +1-562-926-8433 Europe Tech Support & Warranty Claim Please contact us at service@elitescreens.eu or call +49-(0) 40-30392958 Asia Tech Support & Warranty Claim Please contact us at service@elitescreens.com.cn or call +86-(0) 755-8461-7989 Taiwan Tech Support & Warranty Claim Please contact us at service@elitescreens.com.tw or call +866+2+8990-1999 America: Elite Screens Inc 16410 Manning Way Cerritos, CA 90703 USA Tel: +1-877-511-1211 Fax: +1-562-926-8433 info@elitescreens.com www.elitescreens.com Europe: Elite Screens Europe Lübecker Straße 1 22087 Hamburg, Germany Tel: +49-4030392494 Fax: +49-40-49219200 info@elitescreens.eu www.elitescreens.eu Asia: Elite Screens China Corp. Longxi Duimianling Industry Zone Longcheng Longgang District, ShenZhen GuangDong, China Tel: +86-(0)755-8461-7989 Fax: +86-(0)755-8461-7669 info@elitescreens.com.cn www.elitescreens.com.cn Elite Screens France S.A.S 11, Allée William Penn 92150 Surenes, France Tel: +33-1-45064735 Fax: +33-1-45064735 info.fr@elitescreens.com www.elitescreens.com/fr Taiwan: Elite Screens Taiwan Corp. 4F., No. 42-1 Wuguan Rd. Wugu Township Taipei County 248, Taiwan (Wugu Industrial Park) Taiwan (R.O.C) Tel: +886+2+8990-1999 Fax: +886+2+8990+1366 info@elitescreens.com.tw www.elitscreens.com.tw Japan: Elite Screens Japan Corp. 467-2-606 Tsuruma, Machida-shi, Tokyo, 194-0004 Japan Tel: 0120-07-0008 Fax: + 81(0)42-706-9130 info@elitescreens.jp www.elitescreens.jp Latin America Contact: Info.la@elitescreens.com East Asia Contact: Info.ea@elitescreens.com India Contact: Info.india@elitescreens.com 13 Rev.122411-AS www.elitescreens.com info@elitescreens.comMy Name