Regulations require the recycling of Waste from. Electrical and Electronic Equipment (European. “WEEE Directive” effective August 2005—UK.
BLEDPIRBK Eterna 60W LED PIR Bulkhead, 120°, 12m, IP44, Black, Lamp Not Included | YESSS Electrical
LED LAMP SPECIFICATIONS: Lumens total flux 500 lm Lumens 120° flux 450 lm Rated Wattage 7W Rated luminous flux 500 lm Nominal life time of the lamp 35,000 hrs Colour temperature 3100K Number of switching cycles before premature lamp failure 15,000 Warm-up time up to 60 % of the full light output Instant full light Dimmable No LED strip dimensions (L/W) 130x35mm Nominal beam angle 120° Rated power 7W Rated lamp lifetime 35,000 hrs Lamp power factor >0.5 Lumen maintenance factor at end of nominal life 0.70 Starting time <0.1s Colour rendering 80 Colour consistency Within 6 step Macadam ellipse Rated peak intensity 180cd Rated beam angle 120° Voltage 240V Not suitable for accent lighting EVENTUALLY, YOU MAY WANT TO REPLACE THIS PRODUCT: Regulations require the recycling of Waste from Electrical and Electronic Equipment (European "WEEE Directive" effective August 2005--UK WEEE Regulations effective 2nd January 2007). Environment Agency Registered Producer: WEE/ GA0248QZ. WHEN YOUR PRODUCT COMES TO THE END OF ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE RECYCLE IT WHERE FACILITIES EXIST - DO NOT DISPOSE WITH HOUSEHOLD WASTE. Eterna Lighng LTD BLEDBK CODE HERE A+ A 070k0WkhW/h1/1000000hh CLEANING: Disconnect the power and clean the exterior only of this fitting with a moist (not wet) cloth. Do not use any chemical or abrasive cleaners. IF YOU EXPERIENCE PROBLEMS: If you believe your product is defective, please return it to the place where you bought it. Our Technical Team will gladly advise on any Eterna Lighting product, but may not be able to give specific instructions regarding individual installations. Issue 0321 Email: sales@eterna-lighting.co.uk / technical@eterna-lighting.co.uk Visit our website: www.eterna-lighting.co.uk Made in China INSTALLATION INSTRUCTIONS A guide for qualified electricians Model: Pack contents: 1 x LED bulkhead 1 x Fixing kit BLEDBK / BLEDPIRBK 7W LED Bulkhead / 7W LED Bulkhead With PIR These instructions are provided as a guideline to assist you. PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION AND RETAIN FOR FUTURE REFERENCE PIR INTRODUCTION: The bulkhead light incorporates a PIR (passive Infra red) sensing device which continuously scans a preset operating zone and immediately switches the light on when it detects movement in that area. This means that whenever movement is detected within the range of the sensor the light will switch on automatically to illuminate the area you have selected to light. While there is movement within range of the unit the light will remain on. READ THIS FIRST: Check the pack and make sure you have all of the parts listed on the front of this booklet. If not, contact the outlet where you bought this product. This product must be installed by a competent person in accordance with the current building and IEE wiring regulations. As the buyer, installer and/or user of this product it is your own responsibility to ensure that this fitting is fit for the purpose for which you have intended it. Eterna Lighting cannot accept any liability for loss, damage or premature failure resulting from inappropriate use. This product is designed and constructed according to the principles of the appropriate British Standard and is intended for normal domestic service. Using this fitting in any other environments may result in a shortened working life, for example where there are prolonged periods of use or higher than normal ambient temperatures such as lighting public or shared spaces Switch off the mains before commencing installation and remove the appropriate circuit fuse or lock off MCB. This unit is suitable for outdoor use. This product is not suitable for use in bathrooms. This product is designed for permanent connection to fixed wiring: this must be a suitable circuit (protected with the appropriate MCB or fuse). Before making fixing hole(s), check that there are no obstructions hidden beneath the mounting surface such as pipes or cables. Make sure that the fixings are strong enough to support the weight of the fitting and hold it rigidly. The chosen location of your fitting should allow for the product to be securely mounted and anchored to a solid surface e.g. concrete, brick or a joist--do not fix directly onto panelling, cladding, plasterboard etc. This fitting is double insulated; do not connect any part to earth. Make connections to the electrical supply in accordance with the following code: Live (L) Brown or Red Neutral (N) Blue or Black When working at heights ensure you use a suitable platform. The lamp must be positioned so that there is at least 0.5m (500mm) between the bulb and any illuminated surface. When making connections ensure that the terminals are tightened securely and that no strands of wire protrude. Check that the terminals are tightened onto the bared conductors and not onto any insulation. This product is not intended to be used by children and persons with sensory, physical and/or mental impairments that would prevent them from using it safely. You are advised at every stage of your installation to double-check any electrical connections you have made. After you have completed your installation there are electrical tests that should be carried out, these tests are specified in the current IEE wiring and building regulations. WHERE TO FIT YOUR PIR BULKHEAD: To achieve best results we suggest you take the following points into consideration: Do not mount on a surface that has vibration. Ideally the PIR bulkhead light should be mounted 1.8 to 2.5 metres (6 to 8ft) above the area to be scanned (refer to Fig. 1 below). Fig 1 120° Approx 2.5M 8M To avoid damage to the unit do not aim sensor towards the sun. Avoid positioning the sensor unit adjacent to a bright light source which may prevent the unit from operating when the lux control is set to operate in dark conditions. Avoid nuisance false triggering by directing sensor away from: Trees and shrubs Reflective surfaces such as smooth white walls Swimming pools Heat sources such as boiler flues The PIR sensor scanning specifications (approximately 8 metres at 120°) may vary slightly depending on the mounting height and location. INSTALLATION (BOTH MODELS): 01) Switch off the mains power before commencing installation. 02) Remove the diffuser using a screwdriver. 03) Remove the transparent terminal cover plate. 04) P osition the fitting on the surface where it's to be installed and mark the mounting hole positions. The detection range of the unit may also alter with temperature change. Before selecting a place to install your PIR bulkhead you should note that movement across the scan area is more effective than movement directly towards or away from the sensor. (refer to Fig. 2 below). Drill and plug the wall at the marked positions and pass cable wire through the rubber grommet. Screw and fix the lamp body to wall with suitable mounting screws (supplied). If movement is made walking directly towards or away from the sensor and not across, the apparent detection range will be substantially reduced (refer to Fig. 3 below). 05) C onnect the main power wires to the terminal block (see the relative symbols below): 06) Re-screw transparent plate back in place. 07) Refit the diffuser. Fig 2 08) R estore power. (BLEDBK only, see below for BLEDPIRBK instructions). EFFECTIVE: Movement across scan area PIR MODEL ONLY: 08) R estore power. Wait 30 seconds for circuit to stabilise. 09) Set controls. LESS EFFECTIVE: Movement directly in front of scan area Fig 3 PIR SPECIFICATIONS: Detection area: 120° Temp Range: -20°C - 45°C Detection range: Max. 8m Time adjustable: 5 seconds to 5 minutes LUX adjustable: 20 to 2000lux LAMP REPLACEMENT: This luminaire has an LED array and is maintenance free. No replacement is required. Mounting hole Fig 4 Transparent cover Mounting hole L N Brown or Red (Power Cable) Blue or Black (Power Cable) UNDERSTANDING THE PIR CONTROLS: (Referring to Fig. 5 below) ADJUSTING THE DURATION TIME: The length of time that the light remains switched on after activation can be adjusted from (5±5) seconds to (5±1) minutes. Rotating the TIME control from (+) to (-) (clockwise) will reduce the time duration. Note: Once the light has been triggered by the PIR sensor any subsequent detection will start the timed period again from the beginning. Day & Night Night Only LUX Fig 5 LUX (5±1) Minutes (5±5) Seconds TIME TIME Fig 6 EFFECTIVE: Movement across scan area LESS EFFECTIVE: Movement directly in front of scan area ADJUSTING THE LUX CONTROL LEVEL: The lux control module has a built-in sensing device (photocell) that detects daylight and darkness. The (R) position denotes that the bulkhead light can work at day and night, and the () position will only work at night. You can set to operate the light at the desired level by adjusting the LUX dial. SETTING THE CONTROLS: 01) Turn the LUX control to light (R) position, at this stage ensure that the time control is set at minimum duration time (-) position. The bulkhead light will now switch on and remain on for about 5±5 seconds. 02) Direct the sensor toward the desired area to be scanned by adjusting the PIR sensor, have another person move across the centre of the area to be scanned and slowly adjust the PIR sensor until the unit senses the presence of the moving person, causing the lamp to switch on. (Refer to Fig. 6 above). 03) Adjust time control to required setting. 04) T o set the lux level at which the lamp will automatically switch "on" at night, turn the LUX control from daylight to night (). If the lamp is required to switch on earlier, e. g. dusk, wait for the desired environment light level, then slowly turn the LUX control towards daylight (R) while someone walks across the centre of the area to be detected. When the lamp switches on, release the lux control. You may need to make further adjustments to achieve your ideal light level setting. TROUBLESHOOTING AND USER HINTS: Note: all passive infra red detectors are more sensitive in cold and dry weather than warm and wet weather. PROBLEM POSSIBLE CAUSE SUGGESTED REMEDY 1. No mains voltage Check all connections, and MCB Fuses / switches Light does not switch on when there is movement in the detection area. 2. Nearby lighting is too bright 3. Controls set incorrectly 4. Wired incorrectly Relocate the unit Readjust control knob Check wiring and confirm its wired as per the wiring diagram 5. Sensor positioned in wrong direction Relocate the unit 1. H eat sources such as air-con, vents, heaters, flues, other outside lighting, moving cars trees or shrubs are activating sensor Relocate the unit away from these sources. Reduce sensitivity (if available) 2. Animals / birds activating sensor Relocate the unit Light switches on for no apparent reason (false trigger) 3. Interference from on/off switching of electric fans or lights on the same circuit as your security floodlight. (This problem does not always occur but a faulty switch or noisy fluorescent light may cause the security floodlight to switch on) Should the false triggering become, troublesome, consider: (a) Replacing a faulty switch (b) Replacing noisy fluorescent tubes and/or starters (c) C onnecting the fitting to a separate circuit (in most cases where one or more of the above suggestions have been carried out, false triggering has been reduced) 4. R eflection from swimming pool, or reflective surface such as smooth white walls Relocate the unit Light remains on Continuously false triggered Relocate the unit Light remains on at nighttime Possible heat source in detection zone Cover PIR sensor lens with a thick cloth, if the light turns off check detection area for heat or reflective source, reposition head and decrease the sensitivity setting if this control is available Light switches on during daylight hours LUX control knob is set to daylight position Turn the LUX control knob to desired light level setting When setting the lux controls in daylight the detection distance becomes shorter Interference by sunlight Re-test at nightAdobe PDF Library 10.0.1 Adobe InDesign CS6 (Windows)