Garden Arch with Gate Assembly Instructions
This document provides detailed instructions for assembling your Garden Arch with Gate, including a parts list, hardware guide, step-by-step assembly, and return/damage claim information.
Before You Start
⚠️ Please read all instructions carefully.
⚠️ Retain instructions for future reference.
⚠️ Separate and count all parts and hardware.
⚠️ Read through each step carefully and follow the proper order.
⚠️ We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
⚠️ Always place the product on a flat, steady and stable surface.
⚠️ Keep all small parts and packaging materials for this product away from babies and children as they potentially pose a serious choking hazard.
Parts List
- Part A: Curved Top Section (x1)
- Part B: Curved Middle Section (x1)
- Part C: Curved End Section (x1)
- Part D1: Curved Side Section (x1)
- Part D2: Curved Side Section (x1)
- Part E: Straight Upright Support (x1)
- Part F: Vertical Brace (x2)
- Part G: Decorative Side Panel (x2)
- Part H: Decorative Side Panel (x2)
- Part I: Gate Panel (x2)
- Part J: Gate Panel (x2)
- Part K: Gate Base Support (x1)
- Part L: Gate Base Support (x1)
Hardware List
- Part M: M6x30mm Screw (x16)
- Part N: M6x12mm Screw (x6)
- Part O: M6x12mm Bolt (x6)
- Part P: Nut (x6)
- Part Q: Allen Key (x1)
- Part R: Wrench (x1)
Assembly Instructions
Step 1
Connect curved sections A, B, and C.
Description: Join the three main curved sections (A, B, C) using M6x12mm screws (N), nuts (P), the Allen key (Q), and the wrench (R).
Diagram Description: Shows pieces A, B, and C aligning. Screws (N) pass through pre-drilled holes, secured by nuts (P). An inset shows the use of the Allen key (Q) and wrench (R) for tightening.
Step 2
Attach curved side sections to upright supports.
Description: Connect the curved side sections (D1, D2) to the straight upright supports (E) using M6x12mm bolts (O).
Diagram Description: Shows pieces D1 and D2 being attached to the top of piece E. Bolts (O) are inserted through aligned holes. An inset shows a close-up of the bolt connection.
Step 3
Install vertical braces.
Description: Attach the vertical braces (F) to the main curved sections (A, B) using M6x30mm screws (M) and the Allen key (Q).
Diagram Description: Shows two vertical braces (F) being positioned and secured to the inner side of the main arch structure (A, B) with screws (M). An inset shows the screw being tightened with the Allen key (Q).
Step 4
Attach decorative panels to the main arch.
Description: Connect the decorative side panels (G) to the main arch structure using M6x12mm bolts (O).
Diagram Description: Shows decorative panels (G) being attached to the outer sides of the arch. Bolts (O) pass through the panel and into the main frame.
Step 5
Attach remaining decorative panels and gate sections.
Description: Secure the decorative panels (G, J) to the structure using M6x30mm screws (M), M6x12mm screws (N), nuts (P), the Allen key (Q), and the wrench (R).
Diagram Description: Shows decorative panels (G) and gate sections (J) being attached to the lower parts of the arch and gate frame. Various screws, nuts, and tools are indicated for these connections.
Step 6
Assemble the gate.
Description: Join the two gate panels (I) together using M6x12mm bolts (O).
Diagram Description: Shows the two gate panels (I) being connected side-by-side. Bolts (O) are used to secure them.
Step 7
Attach decorative panels to the gate area.
Description: Install the decorative panels (H) onto the gate uprights using M6x30mm screws (M), M6x12mm screws (N), nuts (P), the Allen key (Q), and the wrench (R).
Diagram Description: Shows decorative panels (H) being attached to the vertical supports of the gate area. Screws (M, N) and nuts (P) are used, tightened with tools (Q, R).
Step 8
Install gate base supports.
Description: Attach the gate base supports (K, L) to the bottom of the gate uprights.
Diagram Description: Shows the completed arch with the gate. Parts K and L are indicated as being attached to the bottom of the gate structure, likely for stability or ground anchoring. The inset shows a close-up of the connection point.
Return / Damage Claim Instructions
⚠️ DO NOT discard the box / original packaging.
⚠️ In case a return is required, the item must be returned in original box. Without this your return will not be accepted.
⚠️ Take a photo of the box markings.
A photo of the markings (text) on the side of the box is required in case a part is needed for replacement. This helps our staff identify your product number to ensure you receive the correct parts.
⚠️ Take a photo of the damaged part (if applicable).
A photo of the damage is always required to file a claim and get your replacement or refund processed quickly. Please make sure you have the box even if it is damaged.
⚠️ Send us an email with the images requested.
Email us directly from marketplace where your item was purchased with the attached images and a description of your claim.
