Advantech Co Ltd IDK-1107WP Series TFT LCD 7 WVGA LED Backlight Projected Capacitive Touchscreen User Manual

User Manual for Advantech Co Ltd models including: IDK-1107WP Series TFT LCD 7 WVGA LED Backlight Projected Capacitive Touchscreen, IDK-1107WP Series, TFT LCD 7 WVGA LED Backlight Projected Capacitive Touchscreen, Backlight Projected Capacitive Touchscreen, Projected Capacitive Touchscreen, Capacitive Touchscreen

ADVANTECH IDK-1107WP-50WVA1E (01) PDF MANUAL - Manual-Hub.com

File Info : application/pdf, 37 Pages, 2.83MB

uc?id=1QG3VTq1jRRcFslAaHITgAx518Kyr G8h&export=download

User Manual IDK-1107WP Series
TFT-LCD 7" WVGA (LED Backlight) with Projected Capacitive Touchscreen
https://manual-hub.com/

Copyright
The documentation and the software included with this product are copyrighted 2016 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
AMI is a trademark of American Megatrends Inc. IBM and PC are trademarks of International Business Machines Corporation. Intel® Core 2 Quad, Pentium Dual Core and Celeron are trademarks of Intel Corporation. WinBond is a trademark of Winbond Corporation. All other product names or trademarks are properties of their respective owners.

Part No. 2006110711 Printed in Taiwan

IDK-1107WP User Manual

https://manual-hub.com/

Edition 2 Sep 2016

A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech equipment is destined for the laboratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known. Your satisfaction is our primary concern. Here is a guide to Advantech's customer services. To ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone. So please consult this manual first. If you still cannot find the answer, gather all the information or questions that apply to your problem, and with the product close at hand, call your dealer. Our dealers are well trained and ready to give you the support you need to get the most from your Advantech products. In fact, most problems reported are minor and are able to be easily solved over the phone. In addition, free technical support is available from Advantech engineers every business day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products.

iii
https://manual-hub.com/

IDK-1107WP User Manual

Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events.
Because of Advantech's high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise authorization) number from your dealer. This allows us to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer.

IDK-1107WP User Manual

iv
https://manual-hub.com/

Warnings, Cautions, and Notes
Warning! Warnings indicate conditions, which if not observed, can cause personal injury!
Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g. There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
Note! Notes provide optional additional information.

v
https://manual-hub.com/

IDK-1107WP User Manual

Safety Instructions
1. Read these safety instructions carefully. 2. Keep this User Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage. 7. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet. 8. Position the power cord so that people cannot step on it. Do not place anything
over the power cord. 9. All cautions and warnings on the equipment should be noted. 10. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage. 11. Never pour any liquid into an opening. This may cause fire or electrical shock. 12. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel. 13. If one of the following situations arises, get the equipment checked by service
personnel: The power cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment does not work well, or you cannot get it to work according to the user's manual. The equipment has been dropped and damaged. The equipment has obvious signs of breakage. 14. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -25° C (-13° F) OR ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT.
15. This equipment has been tested and found to comply with the requirements for a Class A digital device.Operation of this equipment in a residential area is likely to cause harmful interference to radio communications; in such events, users are required to correct this interference.
16. This equipment is sold without a power cord. Users are advised to purchase a CCC-certified power cord.
CAUTION: THE COMPUTER IS PROVIDED WITH A BATTERY-POWERED REALTIME CLOCK CIRCUIT. THERE IS A DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.

IDK-1107WP User Manual

vi
https://manual-hub.com/

Contents

Chapter 1
1.1 1.2 1.3 1.4
1.5
Chapter 2
2.1
2.2
Chapter 3
3.1
3.2 3.3
3.4
Chapter 4
4.1
4.2
Chapter 5
5.1 5.2 5.3 5.4 5.5 5.6

General Description and Features .....1
Display Characteristics.............................................................................. 2 Optical Characteristics .............................................................................. 2 Functional Block Diagram ......................................................................... 4 Absolute Maximum Ratings ...................................................................... 5 1.4.1 Absolute Ratings of TFT LCD Module .......................................... 5 1.4.2 Absolute Ratings of Environment.................................................. 5 Outline Dimension..................................................................................... 6
Electrical Characteristics....................7
TFT LCD Module....................................................................................... 8 2.1.1 Power Specification ...................................................................... 8
Table 2.1: Power Specification .................................................... 8 2.1.2 Signal Electrical Characteristics.................................................... 8
Table 2.2: Signal Electrical Characteristics ................................. 8 Backlight Unit ............................................................................................ 9 2.2.1 Parameter Guideline for LED Backlight ........................................ 9
Table 2.3: Parameter Guideline for LED Backlight...................... 9
Signal Characteristics .......................11
Signal Description ................................................................................... 12 3.1.1 Signal Description ....................................................................... 12
Table 3.1: Symbol Description................................................... 12 3.1.2 Backlight Signal Description ....................................................... 12 The Input Data Format ............................................................................ 13 3.2.1 SEL68 ......................................................................................... 13 Interface Timing ...................................................................................... 14 3.3.1 Timing Characteristics ................................................................ 14
Table 3.2: Timing Characteristics .............................................. 14 3.3.2 Input Timing Diagram.................................................................. 15 Power ON/OFF Sequence ...................................................................... 15
Display Connector Definition ...........17
TFT LCD Signal (CN1): LVDS Connector............................................... 18 Table 4.1: TFT LCD Signal (CN1): LVDS Connector ................ 18 Table 4.2: Pin Assignment......................................................... 18
LED Backlight Unit (CN2): LED Driver Connector .................................. 18
Touch Screen .....................................19
Touch Characteristics ............................................................................. 20 Optical Characteristics ............................................................................ 20 Environmental Characteristics ................................................................ 20 Mechanical Characteristics ..................................................................... 20 Electronic Characteristics........................................................................ 20 Mounting Notes ....................................................................................... 21 5.6.1 Mounting ..................................................................................... 21 5.6.2 Caution........................................................................................ 21

vii

IDK-1107WP User Manual

https://manual-hub.com/

Chapter 6
6.1 6.2
6.3 6.4 6.5
Appendix A
A.1

5.6.3 Operating .................................................................................... 21
Touch Controller ............................... 23
Touch Controller Characteristics............................................................. 24 Specifications.......................................................................................... 24
Table 6.1: Specifications ........................................................... 24 OS Driver Support................................................................................... 25 Circuit board dimension .......................................................................... 25 Interface .................................................................................................. 26
Handling Precautions ....................... 27
Handling Precautions.............................................................................. 28

IDK-1107WP User Manual

viii
https://manual-hub.com/

1 Chapter
General Description
1
and Features
https://manual-hub.com/

This manual is for the 7" inch color TFT LCD module IDK-1107WP-50WVA1E which is designed with a wide viewing angle, wide operating temperature, and long life LED backlights which are well suited to display units for Industrial Applications. An LED driving board for the backlight unit is included in this panel and the structure of the LED unit is replaceable. IDK-1107WP-50WVA1E has a built in timing controller and LVDS interface. The screen format is intended to support the SVGA (800(H) x 480(V)) screen and 16.2M (RGB 8-bits) or 262k colors (RGB 6-bits). IDK-1107WP50WVA1E is a RoHS compliant product.
1.1 Display Characteristics
The following table items are display characteristics under 25°C conditions.

Items Screen Diagonal Active Area Pixels H x V Pixel Pitch Pixel Arrangement Display Mode Nominal Input Voltage VDD Typical Power Consumption Weight Physical Size Electrical Interface Surface Treatment Support Color Temperature Range
Operating Storage (Non-Operating) RoHS Compliance

Unit [inch] [mm] [mm]
[Volt] [Watt] [Grams] [mm]
[°C] [°C]

Specifications 7.0 (177.8mm) 152.40(H) x 91.44(V) 800x3(RGB) x 480 0.1905 x 0.1905 R.G.B. Vertical Stripe TN, Normally White 3.3 typ 3.56 typ. 160 ± 10 187.6(W) x 126.64(H) x 12.36(D) typ. 1 channel LVDS Clear, Haze: <2% 262K(6-bit) / 16.2M(8-bit)
-20 to +70 (panel surface temperature) -40 to +80 RoHS Compliance

1.2 Optical Characteristics
Optical characteristics are measured under stable conditions at 25°C (Room Temperature):

Item White Luminance Uniformity Contrast Ratio Response Time
Viewing Angle

Unit [cd/m2]
%

Conditions IF= 80mA (center point) 5 Points

[msec] [msec] [msec] [degree] [degree] [degree] [degree]

Rising Falling Rising + Falling Horizontal (Right) CR 10 (Left) Vertical (Upper) CR 10 (Lower)

Min. Typ. Max. Note

400 500 -

75%

1,5

500 600 -

16 2

60 70

50 60

IDK-1107WP User Manual

2
https://manual-hub.com/

Chapter 1 General Description and Features

Color/Chromaticity Coordinates (CIE 1931)

Contrast Gamut

Red x Red y Green x Green y Blue x Blue y White x White y

0.645 0.341 0.312 Typ 0.625 - 0.03 0.153 0.053 0.313 0.329 72

Typ +0.03

Note1 These items are measured by BM-5A(TOPCON) or CA-1000 (MINOLTA) in the dark room (no ambient light) After 5 minutes operation, the optical properties are measured at the center point of the LCD screen.
Note2 Definition of Response Time (White-Black)

Note3 Definition of Contrast Ratio Contrast ratio is calculated with the following formula :
Contrast Ratio (CR)=(White) Luminance of ON ÷ (Black) Luminance of OFF
Note4 Definition of Luminance Measure the luminance of white state at center point.
Note5 Definition of Luminance Uniformity Measured Maximum luminance [L(MAX)] and Minimum luminance [L(MIN)] on the 9 points Luminance Uniformity is calculated with the following formula: L =[ L(MIN) / L (MAX) ] X 100%
Note6 Definition of Viewing Angle

3
https://manual-hub.com/

IDK-1107WP User Manual

1.3 Functional Block Diagram
The following diagram shows the functional block of the 7 inches Color TFT-LCD Module:

IDK-1107WP User Manual

4
https://manual-hub.com/

Chapter 1 General Description and Features

1.4 Absolute Maximum Ratings
1.4.1 Absolute Ratings of TFT LCD Module

Item Power Supply Voltage

Symbol Vcc

Min. -0.3

1.4.2 Absolute Ratings of Environment

Max. +4

Unit [Volt]

Item Operating Temperature Operation Humidity Storage Temperature Storage Humidity

Symbol TOP HOP TST HST

Min. -20
-40

Max. +70 85 +80 85

Unit [oC] [%RH] [oC] [%RH]

Note 1: Maximum Wet-Bulb should be 38°C and no condensation.
Note 2: The module should be inspected after 1 hour storage in normal conditions (15~35°C, 45~65%RH).

5
https://manual-hub.com/

IDK-1107WP User Manual

1.5 Dimensions
R7,00(X4)
Black Printing area

IDK-1107WP User Manual

6
https://manual-hub.com/

[Unit: mm]

2 Chapter
Electrical
2
Characteristics
https://manual-hub.com/

2.1 TFT LCD Module
2.1.1 Power Specification

Table 2.1: Power Specification

Symbol Parameter

Vcc

Power Supply Voltage

IRUSH

Rush Current

Power Supply Current White

Black

Min. 3.0

Typ. 3.3
140 170

Max. Unit 3.6 V 1.5 A
mA mA

Remark
3 3

Note 1: The assembly should be always operated within the above ranges. Note 2: Measurement condition:

Note 3: The specified power supply current is under the conditions at Vcc=3.3V, Ta=25± 2oC, fv=60Hz, whereas a power dissipation check pattern below is displayed.
2.1.2 Signal Electrical Characteristics

Table 2.2: Signal Electrical Characteristics

Symbol Item

Min. Typ. Max. Unit

VTH

Differential Input High Threshold -

- 100 [mV]

VTL

Differential Input Low Threshold -100 - - [mV]

VCM

Common Mode Voltage

1.2

[V]

Remark VCM=1.2V VCM=1.2V

IDK-1107WP User Manual

8
https://manual-hub.com/

Chapter 2 Electrical Characteristics

2.2 Backlight Unit
2.2.1 Parameter Guideline for LED Backlight
Following characteristics are measured under a stable condition using an inverter at 25°C (Room Temperature):

Table 2.3: Parameter Guideline for LED Backlight

Parameter

Symbol Min. Typ. Max. Unit

Converter Power Supply Voltage Vi

10.8 12 13.2 V

Converter Power Supply Current Ii

0.25 -

Converter Power Consumption

EN Control Level

Backlight on Backlight off

PWM Control Level

PWM High Level
PWM Low Level

PWM Control Duty Ratio

PWM Control Frequency

LED Life Time

PLED
fPWM LL

2.0 -

20 190 200 50,000

3.3 V 0.8 V 3.3 V

0.15 V

100 % 210 Hz
Hrs

Remark
@ Vi=12V (Duty 100%) @ Vi=12V (Duty 100%)

Note 1: LED current is measured by utilizing a high frequency current meter as shown below:
Note 2: The lifetime of the LED is defined as the time when it continues to operate under the conditions at Ta=25±2°C and ILED=50mADC (LED forward current) until the brightness becomes <=50% of its original value.

9
https://manual-hub.com/

IDK-1107WP User Manual

10
https://manual-hub.com/

3 Chapter
Signal Characteristics
3
https://manual-hub.com/

3.1

Signal Description
LVDS is a differential signal technology for LCD interface and high speed data transfer device. The connector pin definition is as below. Note: "Low" stands for 0V. "High" stands for 3.3V. "NC" stands for "No Connected."

3.1.1 Signal Description

Table 3.1: Symbol Description

Pin No. Symbol

Description

RX3+

RX3-

LVDS differential data input Pair 3

No connected

FRC

Dithering control setting When FRC=H, the width of data input 8 bits When FRC=L, the width of data input 6 bits and set Dx0 and Dx1 to logical low (Default pull low)

GND

Ground

RXC+

RXC-

LVDS differential Clock input Pair

GND

Ground

RX2+

RX2-

LVDS differential data input Pair 2

GND

Ground

RX1+

RX1-

LVDS differential data input Pair 1

GND

Ground

RX0+

RX0-

LVDS differential data input Pair 0

Shift direction of Source Driver IC internal shift register is controlled by this pin as show below: LR=H SO1 ->...... SO1200 (Default pull high) LR=L SO1200 ->...... SO1

Gate Driver Up/Down scan setting When UD=H, reverse scan When UD=L, normal scan (Default pull low)

VCC_IN

Digital power supply (+3.3V)

VCC_IN

Digital power supply (+3.3V)

Note: User's connector Part No.: 076B20-0048RA-G4, Starconn, or equivalent.

3.1.2 Backlight Signal Description

Pin No. 1 2 3 4

Symbol Vi ADJ EN VGND

Description Converter input voltage Backlight adjust Enable pin Converter ground

Note: User's connector Part No.: LM123S004HTF13, 4 PIN, UNE.

Note

IDK-1107WP User Manual

12
https://manual-hub.com/

Chapter 3 Signal Characteristics

3.2 The Input Data Format
3.2.1 SEL68

Note1: Please follow PSWG. Note2: R/G/B data 7:MSB, R/G/B data 0:LSB

Signal Name R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0

Description Red Data 7 (MSB) Red Data 6 Red Data 5 Red Data 4 Red Data 3 Red Data 2 Red Data 1 Red Data 0 (LSB) Green Data 7 (MSB) Green Data 6 Green Data 5 Green Data 4 Green Data 3 Green Data 2 Green Data 1 Green Data 0 (LSB)

Remark
Red-pixel Data Each red pixel's brightness data consists of these 8 bits pixel data.
Green-pixel Data Each green pixel's brightness data consists of these 8 bits pixel data.

13
https://manual-hub.com/

IDK-1107WP User Manual

Blue Data 7 (MSB)

Blue Data 6

Blue Data 5

Blue Data 4

Blue-pixel Data

Each blue pixel's brightness data consists of

Blue Data 3

these 8 bits pixel data.

Blue Data 2

Blue Data 1

Blue Data 0 (LSB)

RxCLKIN+ RxCLKIN-

LVDS Clock Input

Display Enable

Vertical Sync

Horizontal Sync

Note: Output signals from any system shall be low or Hi-Z state when VDD is off.

3.3 Interface Timing

3.3.1 Timing Characteristics

Table 3.2: Timing Characteristics

Parameter

Symbol Min. Typ.

Clock frequency

1/ TClock 27

29.5

Period TV

490

500

Vertical Section

Active

TVD

480

Blanking TVB

Period TH

930

992

Horizontal Active Section

THD

800

Blanking THB

130

192

Max. 33 550
70 1090
290

Unit MHz TH
TClock

Condition

Note1: Frame rate is 60 Hz.
Note2: Since this assembly is operated in DE only mode, Hsync and Vsync input signals should be set to low logic level. Otherwise, this assembly would operate abnormally.

IDK-1107WP User Manual

14
https://manual-hub.com/

Chapter 3 Signal Characteristics

3.3.2 Input Timing Diagram

3.4

Power ON/OFF Sequence
VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off.

Parameter
T1 T2 T3 T4 T5 T6

Min. 0.5 0 0 500 20 10

Value Typ. -

Max. 10 50 50 -

https://manual-hub.com/

Unit
[ms] [ms] [ms] [ms] [ms] [ms]
IDK-1107WP User Manual

300

[ms]

The above on/off sequence should be applied to avoid abnormal function in the display. Please make sure to turn off the power when you plug the cable into the input connector or pull the cable out of the connector.

Note 1: The supply voltage of the external system for the module input should be the same as the definition of VDD
Note 2: Apply the lamp voltage within the LCD operation range. When the back-light turns on before the LCD operation or the LCD turns off before the back-light turns off, the display may momentarily become white.
Note 3: In case of VDD = off level, please keep the level of input signal on the low or keep a high impedance.
Note 4: Interface signal shall not be kept at high impedance when the power is on.

IDK-1107WP User Manual

16
https://manual-hub.com/

4 Chapter
Display Connector
4
Definition
https://manual-hub.com/

4.1 TFT LCD Signal (CN1): LVDS Connector

Table 4.1: TFT LCD Signal (CN1): LVDS Connector

Connector Name / Description

Signal Connector

Manufacturer

Starconn or compatible

Mating Model Number

076B20-0048RA-G4, Starconn or equivalent

Table 4.2: Pin Assignment

Pin No.

Signal Name

RX3+

GND

RXC-

RX2+

GND

RX1-

RX0+

VCC_IN

Pin No. 2 4 6 8 10 12 14 16 18 20

Signal Name RX3FRC RXC+ GND RX2RX1+ GND RX0UD VCC_IN

4.2 LED Backlight Unit (CN2): LED Driver Connector

Connector Name / Designation Manufacturer Mating Model Number

LED Connector UNE LM123S004HTF13, 4PIN, UNE

Pin # 1 2 3 4

Symbol Vi ADJ EN VGND

Pin Description Converter Input Voltage Backlight Adjust Enable pin Converter ground

IDK-1107WP User Manual

18
https://manual-hub.com/

5 Chapter
Touch Screen
5
https://manual-hub.com/

5.1

Touch Characteristics
This touch panel is a resistance type that customers use with flat displays like LCDs. Once an operator touches it, the circuit sends coordinate points to the PC from the voltage at contact points.

5.2 Optical Characteristics

Item 1 TRANSPARENCY 2 HAZE

Specification 90% ± 3% <2%

Remarks measured by BYK-Gardner measured by BYK-Gardner

5.3 Environmental Characteristics

Item 1 Operating temperature 2 Storage temperature 3 Operating Humidity 4 Storage temperature

Specification
-20°C ~ 70°C -40°C ~ 80°C
20% ~ 85%RH 20% ~ 90%RH

5.4 Mechanical Characteristics

Remarks
When the ambient temperature is above 65oC, the humidity is allowed to be below 50%RH.

Item 1 Hardness of surface
2 FPC peeling strength 3 Operation force

Specification Pencil hardness 7H.
800g by vertical 90°
Finger10g, 8

5.5 Electronic Characteristics

Remarks ASTM D3363
Pressure: 750g/45°
for 30 sec
Within "guaranteed active area", but not on the age.

Item 1 Response
2 Accuracy
3 Multi-Touch Fingers Pitch

Specification
< 25ms
Line Drawing: 1pt ± 1mm offset /10mm 2pt ± 2mm offset / 10mm touch point: 1pt ± -2.5mm 2pt ± -5.0mm Refer to Windows 7 Logo Regulation
Between the Finger Pitch > 10mm

Remarks
Channel Pitch Should be 5mm~7mm

IDK-1107WP User Manual

20
https://manual-hub.com/

Chapter 5 Touch Screen

5.6 Mounting Notes

5.6.1

Mounting
The gasket of the touch panel must be designed for the outside of the viewable area to avoid pressing on the touch panel accidentally and the enclosure must be designed with enough clearance from the panel surface. To avoid pressing errors on the touch panel, please allow space between the surface of the panel and the bezel.
We recommended elastic type materials. The edge of the touch panel is conductive. Don't touch it with metal after mount-
ing. Please take notice of grounding while mounting the touch screen, otherwise
interference may cause unstable performance. Please do not pull on the flex tail during assembly. Do not bend at 90 degrees
and each bend angle should be no less than R=5m/m During assembly, the touch panel must be securely affixed onto the LCD panel
to prevent displacement of the touch panel due to outside force pressing on touch screen or bezel/case.

5.6.2 Caution

5.6.2.1 Installing and Assembling Do not use excessive force or strain to the panel or tail. Gasket or cushion pads around the edge of the panel may segregate water and/ or dust contamination. Maintain a minimal 5R when bending the tail to prevent dead folds or fold marks. Flaws in customer module design may cause functionality issues after assembly.

5.6.3

Operating
Touch the panel with your finger or stylus only to test normal operation. Any sharp edged or hard objects should not be used.
Operate the panel in a steady environment. Abrupt variation on temperature and humidity may cause malfunctions to the panel.

21
https://manual-hub.com/

IDK-1107WP User Manual

Avoid applying excessive activation force or sudden impact on the panel surface.
Avoid high voltages and / or static charge.
5.6.3.1 Others Keep the panel surface clean. Prevent any kind of adhesive or tape applied onto the touch surface.

IDK-1107WP User Manual

22
https://manual-hub.com/

6 Chapter
Touch Controller
6
https://manual-hub.com/

6.1

Touch Controller Characteristics
EETI EXC3132 is a MCU based projected capacitive touch screen controller designed for commercial and industrial applications. EXC3132 controller supports high voltage driving signal to achieve high SNR and better wideband interference susceptibility.
EXC3132 provides different working frequencies to avoid narrow band interference. With high voltage driving and different working frequencies, EXC3132 provides excellent interference susceptibility performance. EXC3132 provides an excellent solution for not only finger operation but also with gloves, thicker glass, etc. applications.

6.2 Specifications

Table 6.1: Specifications
Clocks
Power Management ESD Analog Models Communication Interface Digital Modules Operation Temperature Storage Temperature Power Consumption (mA)
Relative Humidity Linearity (Note 1)

External 12M HZ crystal Internal PLL Internal 32 bits RTC Clock generator for digital modules Clock generator for analog modules Power supply : 3.3~5.5 VDC Internal regulator for analog clock Internal regulator for digital core Idle mode Sleep mode 4000V(HBM) Up to 32 RX channels Up to 18 TX channels Signal generator USB 2.0 compliant full speed with LPM L1 supported Configurable Serial Interface -I2C : up to 400KHZ, support 3.3V Timers, Watch dog Timer Multi-touch algorithm accelerator Hardware scan ending -40 to 85°C -40 to 90°C Active Mode: 35mA Idle Mode: 34mA Sleep Mode :<33mA (Operation Mode: Active Mode only) 95% at 60°C, RH Non-condensing Line drawing accuracy: 1pt +/- 1mm offset /10mm Line drawing accuracy: 2pt +/- 2mm offset /10mm Touch (point) accuracy: 1pt +/- 2.5mm Touch (point) accuracy: 2pt +/- 5.0mm Refer to Windows 7 Logo regulation

IDK-1107WP User Manual

24
https://manual-hub.com/

Chapter 6 Touch Controller

6.3 OS Driver Support

OS Windows
Linux
Mac QNX

Version
Windows 7/ 8/10
Windows Vista, XP/2000, 9x/ME
Windows CE 2.12/3.0/.net/5.0/6.0
Windows Embedded
Windows XP Tablet PC edition
Mandrake (Mandrake 9.1/9.2/10, Mandriva 2005, Mandriva 2006), Red Hat (7.3/8.0/9.0), Fedora (Core I/II/III/IV/V/VI), Yellow Dog (3.X) , SuSE (9.2/9.3/10/10.1), Ubuntu (5.1/6.06), Debian (3.1, Kernel 2.4.x/2.6.x)
Android 4.0 Google Moblin V2/Meego - Intel
Mac OS9, Mac OS X (IBM, intel CPU)
QNX RTOS v6.3

6.4 Circuit board dimension

Interfaces USB
USB (up to Kernel 2.6.x)
USB USB USB

25
https://manual-hub.com/

IDK-1107WP User Manual

6.5 Interface

IDK-1107WP User Manual

26
https://manual-hub.com/

A Appendix
Handling Precautions
A
https://manual-hub.com/

A.1 Handling Precautions
The optical characteristics are measured under stable conditions at 25°C (Room Temperature)
1. Since front polarizer is easily damaged, pay attention not to scratch it. 2. Be sure to turn off power supply when inserting or disconnecting from input con-
nector. 3. Wipe off water drops immediately. Long contact with water may cause discolor-
ation or spots. 4. When the panel surface is soiled, wipe it with absorbent cotton or other soft
cloth. 5. Since the panel is made of glass, it may break or crack if dropped or bumped on
hard surface. 6. Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling. 7. Do not open or modify the Module Assembly. 8. Do not press the reflector sheet at the back of the module to any directions. 9. In case if a Module has to be put back into the packing container slot after once
it was taken out from the container, please press at the far ends of the LED light bar reflector edge softly. Otherwise the TFT Module may be damaged. 10. At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module. 11. After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged. 12. A small amount of materials having no flammability grades have been used in the LCD module. The LCD module should be supplied by power complying with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exempt of them.

IDK-1107WP User Manual

28
https://manual-hub.com/

www.advantech.com
Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2016
https://manual-hub.com/

References