ErGear Electric Standing Desk

Instruction Manual

Model Numbers:

EGESD18B / EGESD18V / EGESD18N

Technical Support

(US/CA) 1-800-651-9525 (Mon-Fri, 8am-8pm CST)

(UK) 44-808-196-3875 (Mon-Fri, 2pm-10pm UTC)

Other Info: support@ergear.com

Website: https://ergear.com

Tools Needed (Not Included)

• Drill ?️ (not included)
• Phillips Screwdriver ? (not included)

Specifications

Desktop Dimensions

57.1" (145cm)

Height Adjustment Range

28.3"–46.5" (72–118cm)

Power Input

100V–240V

Max. Speed

20mm/s

Operating Noise

<55dB

Max. Load

176 lbs / 80kg

Supplied Parts and Hardware

Frame Components

01 Short Crossbar x 1

02 Long Crossbar x 1

03 Left Desk Leg x 1

04 Right Desk Leg x 1

05 Short Side Plate x 1

06 Long Side Plate x 1

07 Short Leg Base x 1

08 Long Leg Base x 1

09 Crossbar Connector x 1

Hardware

A Bolt M6 x 35mm x 8

B Bolt M6 x 11mm x 12

C1 Large Allen Wrench 3/16" (5mm) x 1

C2 Small Allen Wrench 5/64" (2mm) x 1

D Rubber Pad x 16

10 Transmission Rod x 1

Desktop Components

11 Left Desktop Panel x 1

12 Right Desktop Panel x 1

E Desktop Panel Connector x 2

Controller and Accessories

13 Controller x 1

14 Storage Hook x 2

15 Cable Clip x 2

16 AC Adapter x 1

Fasteners

F Screw M5 x 16mm x 30 (8 for frame, 22 for desktop)

G Wood Dowel Pin x 3

Step 1: Assembling the Frame

Connect the crossbars (01, 02) together using the crossbar connector (09). Secure with bolts (B) and the large Allen wrench (C1).

Attach the desk legs (03, 04) to the assembled crossbar structure. Secure with bolts (B) and the large Allen wrench (C1).

Attach the leg bases (07, 08) to the bottom of the desk legs (03, 04). Secure with bolts (A) and the large Allen wrench (C1).

Attach the side plates (05, 06) to the desk legs (03, 04). Secure with bolts (B) and the large Allen wrench (C1).

Loosen the coupling nut (on transmission rod 10). Before attaching the transmission rod, measure the heights of the two desk legs to ensure they are level. If not, insert the transmission rod (10) into the hole in the left leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it until it is level with the right leg.

Ensure the transmission rod (10) is properly inserted into the hole in the left leg. Connect the other end of the rod to the motor drive shaft on the right leg. NOTE: Make sure the set screw faces outwards.

Secure the transmission rod (10) to the motor drive shaft by turning the set screw clockwise using the small Allen wrench (C2).

Tighten the coupling nut (on transmission rod 10) to fine-tune the transmission rod fit.

Step 2: Assembling the Desktop

Assemble the desktop panels (11, 12). Insert wood dowel pins (G) into the designated holes on one panel and align the other panel. Press them together.

Secure the desktop panels (11, 12) together using the desktop panel connectors (E). Use screws (F) and a drill or Phillips screwdriver.

Step 3: Attaching the Desktop

Attach the assembled desktop to the frame. Align the pre-drilled holes on the underside of the desktop with the frame. Secure with screws (F) using a drill or Phillips screwdriver.

Attach the controller (13) and storage hooks (14) to the underside of the desktop. Secure with screws (F) using a drill or Phillips screwdriver.

Step 4: Connecting the Cables

Connect the controller (13) to the AC adapter (16) and the motor drive shaft (via the transmission rod connection). Route cables neatly using cable clips (15).

Connect the AC adapter (16) to the controller (13).

Using the Controller

The controller allows you to adjust the desk height and save presets.

Controller Interface

The controller typically features buttons for saving height settings, selecting presets, raising, and lowering the desk.

• Save Current Height Setting: Short-press the [Save] button (often labeled 'S' or a disk icon ?), and the display will flash. Press the [1], [2], or [3] button to save the current height setting to that preset.
• Select Height Setting 1: Press the [1] button. The desk will move to the height previously saved for preset 1.
• Select Height Setting 2: Press the [2] button. The desk will move to the height previously saved for preset 2.
• Select Height Setting 3: Press the [3] button. The desk will move to the height previously saved for preset 3.
• Raise the Desk: Press the [Up Arrow] button (⬆️) to raise the desk continuously until it reaches the highest position of 46.5" (118cm) or the button is released.
• Lower the Desk: Press the [Down Arrow] button (⬇️) to lower the desk continuously until it reaches the lowest position of 28.3" (72cm) or the button is released.

Settings

Change Display Height Units

Press and hold the [S] button until 'S-' is displayed. Press [S] again, and 'Un' is displayed. Press [Up Arrow] or [Down Arrow] to switch between 'IN' (imperial) and 'SI' (metric), and press [S] to save your choice.

Change Collision Detection Sensitivity

Long press the [S] button; 'S-' shows and flashes. Press [S] again and the display shows 'Un'. Press [Up Arrow] or [Down Arrow] to switch to 'CF'. Press [S] to select. Press [Up Arrow] or [Down Arrow] to switch between 'OFF', Low (L), Normal (n), or Heavy (H) collision force detection. Press [S] to save your choice.

Reset

Press and hold the [Down Arrow] button (⬇️) for 5 seconds. The screen will show 'RES.' Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Hot (Overheating Protection)

When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.

E10 (Sensor Malfunction Warning)

Motor safety sensor can't be detected. Power off, check the connection between the motor and controller, and power back on again.

E20 (Overloading Warning)

Max load exceeded. If raising the desk, remove items and try again. If lowering the desk, power off, remove items, power back on, and try again.

E02 (Operation Status Warning)

The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.

E32 (Overvoltage Protection)

Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.

E31 (Undervoltage Protection)

Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.

E60 (Unequal Leg Height Warning)

Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again.

- (Cable Disconnection Warning)

Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

Thank You

Thank you for choosing this product. For any issues, please contact ErGear support.

Technical Support: (US/CA) 1-800-651-9525 (Mon-Fri, 8am-8pm CST), (UK) 44-808-196-3875 (Mon-Fri, 2pm-10pm UTC)

Other Info: support@ergear.com

Website: https://ergear.com