Smart Clean Robo Vac 2000

Important Safety Information

User Cautions

⚠️ Store and operate the Smart Clean Robo Vac 2000 in temperature-controlled environments only.

⚠️ The Smart Clean Robo Vac 2000 should not be used by children and persons with reduced physical, sensory, or mental capabilities. Children should not play with the Smart Clean Robo Vac. Cleaning and user maintenance should only be done by adults.

⚠️ Do not use the Smart Clean Robo Vac to clean up spills, bleach, chemicals, or anything wet.

⚠️ If the room to be cleaned contains a balcony, a physical barrier must be used to prevent the Smart Clean Robo Vac from falling.

⚠️ Do not place anything on top of the Smart Clean Robo Vac.

⚠️ Be aware that the Smart Clean Robo Vac is moving. Be careful when walking in the area.

⚠️ Ensure there are no exposed electrical outlets in the floor.

? Before using the Smart Clean Robo Vac, remove loose objects like clothing, loose papers, pull cords for blinds or curtains, power cords, and any fragile objects.

? Charge indoors only.

? Always remove the battery before cleaning or maintaining the Smart Clean Robo Vac, battery, or charging Dock.

? The Smart Clean Robo Vac is not a toy. Do not sit or stand on the Smart Clean Robo Vac. Small parts may be a choking hazard.

? Do not attempt to use the Smart Clean Robo Vac to pick up anything that is burning or smoking.

⚠️ Damage caused by improper use or failure to follow these safety instructions may result in injury or damage.

? Retain the safety and operating instructions for future reference.

? Heed all warnings on your Smart Clean Robo Vac.

? Do not dispose of electrical appliances as unsorted municipal waste; use separate collection facilities. Contact your local authority for information.

Battery Care & Charging

? Charge using a standard outlet only. This product may not be used with any type of power converter.

? Do not use the cord or plug. If the cord or plug is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.

? Do not use a Charging Dock with a damaged cord or plug.

? Disconnect the Charging Dock from the power outlet during electrical storms or when unused for long periods.

? Do not wet the battery compartment.

⚠️ If the batteries are leaking, stop the Smart Clean Robo Vac use immediately.

? This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Product and Contents

Smart Clean Robo Vac 2000

A robotic vacuum cleaner designed for automated cleaning.

Key features include WiFi connectivity, app control, and remote control capabilities.

Indicator Lights:

• Solid Red: ? Indicator.
• Flashing Red: WiFi connection error or network issue.
• Rapidly Flashing (intermittent 250ms): WiFi configuration state.
• Slowly flashing (intermittent 1s): WiFi connection failed.
• Lamp off: ? configured successfully and connected.

Buttons:

• Auto Cleaning/Start/Stop Button: Press ▶️ to start/pause cleaning. Press & hold for 5 seconds to reset WiFi.

Other Components:

• Driving Wheels: For navigation.
• Anti-Drop Sensors: Prevent falls from stairs.
• Charging Contacts: For connecting to the charging dock.
• Dust Bin: Collects dirt and debris.
• Filter: Traps fine particles.
• Side Brush: Sweeps debris towards the main suction area.

Troubleshooting Indicator:

• Indicator Flashing Red: Your smartphone or tablet is connected to a WiFi network. The 2.4 GHz band wireless signal is enabled in your wireless router. Smart Clean Robo Vac is attached to the Charging Base to ensure it has enough power.

Accessories

The Smart Clean Robo Vac 2000 typically includes:

• Charging Dock
• [remote] Control
• Side Brushes (often spares)
• Filter (often spares)
• Cleaning Tool

[Diagram description: A collection of small parts including side brushes, filters, and possibly a cleaning tool.]

Charging Dock

The base station for recharging the Robo Vac.

Charging Dock Position:

[Diagram description: Illustration showing the correct placement of the charging dock against a wall, with clear space around it for the robot to dock. Recommended clearance: 0.5m on both sides, 1.5m in front.]

Setup:

Plug in the Charging Dock and place the Smart Clean Robo Vac on it to begin charging.

Operating Instructions

Notes Before Cleaning

Ensure the area is clear of obstacles like power cords, small rugs, and low-hanging curtains.

Remove any fragile objects or items that could be damaged or obstruct the robot.

Using the Smart Clean Robo Vac

Start a Cleaning Cycle: Press the Auto Cleaning/Start/Stop button on the unit or use the [remote] or app.

Pause Cleaning Cycle: Press the Auto Cleaning/Start/Stop button again.

Return to Charging Dock: Use the dedicated button on the [remote] or app, or the robot will automatically return when its battery is low.

Cleaning Modes

• Auto Cleaning: The robot cleans the entire accessible area systematically.
• Spot Cleaning: For concentrated cleaning of a specific area. Place the robot in the center of the area to be cleaned. The robot will clean in a spiral pattern.
• Edge Cleaning: The robot cleans along walls and around furniture legs. The robot will boost suction power when it detects an edge.
• Manual Cleaning: Control the robot's movement direction using the [remote] or app.

Smart Clean Robo Vac Care

Regular maintenance ensures optimal performance and longevity.

Emptying the Dust Bin

Frequency: After each cleaning cycle, or when the dust bin is full.

Steps:

1. Press the release button on the dust bin and pull it out.
2. Open the dust bin lid and empty the contents into a trash receptacle.
3. Close the dust bin lid.
4. Reinsert the dust bin into the robot.

[Diagram description: Illustration showing how to remove and empty the dust bin.]

Cleaning the Filter

Frequency: Weekly, or as needed.

Steps:

1. Remove the dust bin.
2. Open the dust bin lid and remove the filter.
3. Tap the filter gently against a trash receptacle to remove dust. Do not wash the filter unless specified as washable.
4. Reinsert the filter into the dust bin.

[Diagram description: Illustration showing how to remove and clean the filter.]

Cleaning the Side Brush

Frequency: Monthly, or if performance degrades.

Steps:

1. Turn the robot upside down.
2. Locate the side brush. It may be attached with a screw.
3. Remove the side brush.
4. Remove any tangled hair or debris from the brush and the mounting area.
5. Reattach the side brush securely.

[Diagram description: Illustration showing how to remove and clean the side brush.]

Cleaning the Anti-Drop Sensors and Charging Contacts

Frequency: Monthly.

Steps:

1. Turn the robot upside down.
2. Gently wipe the anti-drop sensors (located on the underside) with a clean, dry cloth.
3. Wipe the charging contacts on the robot and the charging dock with a clean, dry cloth.

[Diagram description: Illustration highlighting the locations of the anti-drop sensors and charging contacts on the robot.]

Cleaning the Smart Clean Robo Vac Floor

Frequency: As needed.

Steps:

1. Wipe the exterior surfaces of the robot with a soft, damp cloth.
2. Do not use harsh chemicals or abrasive cleaners.

Voice Control

Using the Smart Clean Robo Vac with Google Assistant

You can control the Smart Clean Robo Vac using voice commands via Google Assistant-enabled devices.

Requirements:

• Smart Clean Robo Vac 2000 must be on the Charging Dock.
• Google Home app or Amazon Alexa app installed on your smart device.
• A device with Google Assistant (e.g., Google Home, Google Home Mini).
• Google Assistant control is currently only available in English.

How to Control:

1. Open the Google Home app.
2. Say, "OK Google, talk to Smart Vac."
3. Follow the instructions in the Google Home app to link your Tzumi Smart Action.
4. You are now ready to use voice commands.

Example Voice Commands:

• "OK Google, ask Smart Vac to start cleaning."
• "OK Google, ask Smart Vac to return to the charging dock."

Using the Smart Clean Robo Vac with Amazon Alexa

You can control the Smart Clean Robo Vac using voice commands via Amazon Alexa-enabled devices.

Requirements:

• Smart Clean Robo Vac 2000 must be on the Charging Dock.
• Google Home app or Amazon Alexa app installed on your smart device.
• A device with Amazon Alexa (e.g., Echo, Echo Dot).

How to Control:

1. Open the Amazon Alexa app.
2. Navigate to Skills & Games, search for 'Tzumi Smart', and tap 'Enable'.
3. Link your Tzumi account.
4. Discover devices.
5. You are now ready to use voice commands.

Example Voice Commands:

• "Alexa, tell Smart Vac to start cleaning."
• "Alexa, tell Smart Vac to go home."

App Control

Controlling the Smart Clean Robo Vac via the Tzumi Smart Home APP

Use the Tzumi Smart Home app for advanced control and scheduling.

Steps:

1. Download the 'Tzumi Smart Home' app from the App Store or Google Play.
2. Scan the QR code provided in the manual (or search for the app).
3. Follow the instructions in the app to set up the WiFi connection for your Robo Vac 2000.
4. Once connected, you can select a cleaning mode, set a cleaning schedule, and monitor the robot's status.

[Diagram description: QR codes for downloading the Tzumi Smart Home app from the App Store and Google Play.]

To see an up-to-date list of available commands, go to the Tzumi Smart APP, tap on 'Me', and tap on 'More Services'.

Troubleshooting

Issue: Indicator Lamp Off, ? not connected.

Possible Cause: ? not configured successfully.

Solution: Follow the ? connection setup instructions in the app.

Issue: Indicator Lamp Rapidly Flashing.

Possible Cause: ? configuration state.

Solution: Wait for the configuration to complete or reset ?.

Issue: Indicator Lamp Slowly Flashing.

Possible Cause: ? connection failed.

Solution: Ensure your router is on, supports 2.4GHz, and the password is correct. Try resetting the ? on the robot.

Issue: Robot not charging.

Possible Cause: Charging contacts are dirty or blocked.

Solution: Clean the charging contacts on the robot and the charging dock.

Possible Cause: Charging dock not powered.

Solution: Ensure the charging dock is plugged in.

Issue: Robot stuck or not moving correctly.

Possible Cause: Obstacles blocking movement or sensors.

Solution: Clear the area of obstacles. Clean the anti-drop sensors and wheels.

Possible Cause: Driving wheels are blocked.

Solution: Check and clear any obstructions from the driving wheels.

Issue: Weak suction power.

Possible Cause: Dust bin is full or filter is clogged.

Solution: Empty the dust bin and clean or replace the filter.

Possible Cause: Brushes are tangled.

Solution: Clean the main brush and side brushes.

Rebooting Instructions

To reset the WiFi connection, press and hold the Auto Cleaning/Start/Stop button for 5 seconds.

For more complex issues, consult the Tzumi Smart Home app or customer support.

Specifications

Suction Power: [Value not specified in OCR]

Battery Type: [Value not specified in OCR]

Battery Capacity: [Value not specified in OCR]

Charging Time: [Value not specified in OCR]

Working Time: [Value not specified in OCR]

Dust Capacity: [Value not specified in OCR]

Noise Level: [Value not specified in OCR]

Dimensions: [Value not specified in OCR]

Weight: [Value not specified in OCR]

WiFi Standard: 802.11 b/g/n (2.4GHz)