2.4G Wireless Keyboard and Mouse Combo

Product Specifications

Keyboard Parameters

• Dimensions: 443*136*30mm
• Weight: 555±5g
• Connection: 2.4G Wireless Connection
• Receiver Type: USB Nano Receiver
• Battery Capacity: 1500mAh
• Working Current (without backlight): 2mA
• Working Time (without backlight): 750 hours
• Working Current (with brightest backlight): 40 mA
• Working Time (with brightest backlight): 35 hours
• Standby Current: 50uA
• Standby Time: 365 days
• Backlight Sleep Mode: 2 minutes without use (Press any key to activate)
• Keyboard Sleep Mode: 30 minutes without use (Press any key to activate)

Mouse Parameters

• Battery Capacity: 650mAh
• Mouse DPI: 800-1200-1600
• Power Saving: Enters sleep mode after 1.5 minutes of inactivity.
• Charging Time of Mouse: 3 hours
• Charging Time of Keyboard: 3 hours
• Working Current (with Backlight): 15mA
• Working Time (with backlight): 44 hours
• Working Current (without backlight): 3mA
• Working Time (without backlight): 200 hours

How to Set Up

1. Step 1: Plug the USB dongle into your computer.

   Diagram: Shows a USB Nano Receiver being plugged into a computer's USB port.

2. Step 2: Turn on the keyboard and mouse.

   Diagram: Shows the power switches on the keyboard and mouse being moved to the 'ON' position.

3. Step 3: The keyboard and mouse will automatically connect to the computer; no driver is needed.

Instruction of the Keyboard Backlight

1. Press and Hold Fn key, then press the Scrik key to turn on/turn off backlight.

2. Press and Hold Fn key, then press PgUp key to increase backlight brightness (low-mid-high-off).

3. Press and Hold Fn key, then press PgDn key to decrease backlight brightness.

Lighting Switch: Press the button for 3 seconds to turn on/off the lighting. Click the LED Switch Button to switch between 15 different lighting effects.

Diagram: Illustrates the Fn key combinations for backlight control and a separate button for lighting effects.

LED Indicator of the Keyboard

• Low Battery: The red LED light will flash.
• Charging: The red LED light will be on.
• Fully Charged: The red LED light will turn off.

LED Indicator of the Mouse

• Charging: The red LED light will be on.
• Fully Charged: The red LED light will turn off.

Battery Indicator/Charging Indicator: If the battery is low, please charge the mouse so that it will work properly.

How to Repair the Keyboard to the USB Receiver

1. Unplug the USB dongle.
2. Turn on the keyboard.
3. Press and hold the "ESC" and the "=" key together for 3-5 seconds.
4. Plug in the USB receiver and place the keyboard as close as possible to the USB receiver.
5. When the LED indicator for low battery/connection turns off, the keyboard is successfully connected.

Diagram: Shows the ESC and '=' keys being pressed simultaneously, followed by plugging in the USB receiver near the keyboard.

How to Repair the Mouse to the USB Receiver

1. Pull out the USB receiver from your computer.
2. Turn off the mouse.
3. Plug the receiver into the USB port of the computer, turn on the mouse, and wait for 5 seconds.
4. The mouse will connect.

Diagram: Illustrates unplugging the USB receiver, turning off the mouse, plugging the receiver back in, and turning on the mouse.

Notes

• The multimedia keys are designed for Win 8 and Win 10. For other systems, some combined keys may not function.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.