VTech Toot-Toot Cory Carson Cory's Stay & Play Home Parent's Guide

Included in this Package

NOTE: This toy is not intended for teething.

• One mini Mama
• One mini Cory
• One mini Chrissy
• One chair
• One playmat
• One arch
• One door
• One first floor base
• Two columns
• One corner pillar
• One bath roller
• One bathtub wall
• One second floor base
• One bedside table
• One clock & tent
• One bed
• One house top
• One light
• One TV stand
• One TV stand cover
• One refrigerator
• One refrigerator door
• One main floor wall
• One second floor hallway
• One fireplace wall
• One connector
• One window
• One pole
• One ramp
• One label sheet
• One Parent's Guide

WARNING: All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties, cords and packaging screws are not part of this toy and should be discarded for your child's safety.

NOTE: Please keep this Parent's Guide as it contains important information.

Getting Started

Battery Removal and Installation

1. Make sure the unit is turned OFF.
2. Locate the battery cover underneath the second floor of the house. Then, use a coin or a screwdriver to loosen the screw and remove the cover.
3. Remove old batteries by pulling up on one end of each battery.
4. Install 3 new AAA (AM-4/LR03) batteries following the diagram inside the battery box. (The use of new alkaline batteries is recommended for maximum performance).
5. Replace the battery cover and tighten the screw to secure.

Battery Notice

• Use new alkaline batteries or fully charged NI-MH (Nickel Metal-hydride) rechargeable batteries for best performance.
• Use only batteries of the same or equivalent type as recommended.
• Do not mix different types of batteries: alkaline, standard (carbon-zinc) or rechargeable, or new and used batteries.
• Do not use damaged batteries.
• Insert batteries with the correct polarity.
• Do not short-circuit the battery terminals.
• Remove exhausted batteries from the toy.
• Remove batteries during long periods of non-use.
• Do not dispose of batteries in fire.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging (if removable).
• Rechargeable batteries are only to be charged under adult supervision.

Disposal of batteries and product

The crossed-out wheelie bin symbols on products and batteries, or on their respective packaging, indicates they must not be disposed of in domestic waste as they contain substances that can be damaging to the environment and human health.

The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains more than the specified value of mercury (Hg), cadmium (Cd) or lead (Pb) set out in Battery Directive (2006/66/EC).

The solid bar indicates that the product was placed on the market after 13th August, 2005.

Help protect the environment by disposing of your product or batteries responsibly.

For more information, please visit:

www.recycle-more.co.uk

www.recyclenow.com

Label Application

Please apply the labels to the play set as shown below:

A visual diagram shows the placement of various labels on the playset components.

Assembly Instructions

With the Cory's Stay & Play Home, safety comes first. To ensure your child's safety, adult assembly is required.

1. Place the Door into the Arch and press into place. [arrow pointing inwards]
2. Lay the First Floor Base face up on a flat surface. Insert the two Arch posts into the first floor. Press down until you hear a click. [diagram showing insertion]
3. Insert the two Columns into the First Floor Base. [diagram showing insertion]
4. Insert the Corner Pillar into the First Floor Base. Press down until you hear a click. [diagram showing insertion]
5. Press the Roller into the Bathtub Wall until you hear a click. [diagram showing insertion]
6. Insert the Bathtub Wall into the Second Floor Base behind the tub. Press down until it clicks into place. [diagram showing insertion]
7. Insert the Bedside Table into the Second Floor Base. Press down until you hear a click. [diagram showing insertion]
8. Insert the Clock & Tent into the Second Floor Base. Press down until you hear a click. [diagram showing insertion]
9. Push the Bed into the Second Floor Base until you hear a click. [diagram showing insertion]
10. Connect the House Top to the Second Floor Base as shown below. [diagram showing connection]
11. Flip the house over so the bottom is exposed. Insert the Light into the bottom of the Second Floor Base. Press until you hear a click. [diagram showing insertion]
12. Attach the TV Stand Cover to the TV Stand. Press until you hear a click. [diagram showing attachment]
13. Insert the TV Stand into the Second Floor Base. Press until you hear a click. [diagram showing insertion]
14. Align all posts and columns with corresponding slots underneath the second floor. Press down until you hear a click to indicate both floors are secure. [diagram showing alignment]
15. Attach the Refrigerator Door to the Refrigerator. Press until you hear a click. [diagram showing attachment]
16. Connect the Refrigerator to the TV Stand as shown below. Press until you hear a click. [diagram showing connection]
17. Insert the Main Floor Wall into the Second Floor Hallway as shown below. Press down until you hear a click. [diagram showing insertion]
18. Insert the Fireplace Wall into the Second Floor Hallway as shown below. Press until you hear a click. [diagram showing insertion]
19. Add the Connector to the Second Floor Hallway as shown below. Press until you hear a click to indicate it is secure. [diagram showing addition]
20. Insert the Pole into the Window as shown below. Press until you hear a click. [diagram showing insertion]
21. Attach the Window to the Second Floor Hallway as shown below. Press down until you hear a click. [diagram showing attachment]
22. Connect the Second Floor Hallway segment to the Second Floor Base as shown below. Press until you hear a click to indicate it is secure. [diagram showing connection]
23. Connect the Ramp track to the Second Floor Hallway as shown below. [diagram showing connection]

Once you've completed the above steps, you are ready to play. PlayZone characters from other sets (sold separately) are also compatible.

Folding Instructions

1. Remove the ramp and rotate the hallway section to the front. Secure in place with the tab. [diagram showing folding]
2. Fold the kitchen flat against the house. [diagram showing folding]
3. The house is now folded and ready to store. [diagram showing folded house]

Product Features

1. On/Off/Volume Control Switch

To turn the house On, slide the On/Off/Volume Control Switch to the Low Volume ? or the High Volume ? position. You will hear the Toot-Toot Cory Carson® theme song and fun sounds. To turn the house Off, slide the On/Off/Volume Control Switch to the Off ? position.

2. Automatic Shut-Off

To preserve battery life, Cory's Stay & Play Home will power down after approximately 60 seconds without input. The unit can be turned on again by pressing the buttons or triggering the PlayZone Location with a mini character.

NOTE: If the unit powers down while playing, please install a new set of batteries.

Activities

1. PlayZone Location

Place Cory, Chrissy, Mama or other Toot-Toot Cory Carson® mini characters (sold separately) on the PlayZone Location to trigger fun phrases and sounds from the show. The light will flash with the sounds. [image of playset with character on PlayZone]

2. Clock Button

When a mini character is on Cory's bed, press the Clock Button to reveal Papa, trigger fun sounds, songs and phrases from the show, and launch the character down the ramp. [image of playset with character on bed and ramp]

3. Bath Button

Press the Bath Button to hear fun phrases, melodies and sounds from the show. When Cory, Chrissy or Mama are on the PlayZone Location press the Bath Button to hear Papa interact with them. Place other Toot-Toot Cory Carson® mini characters (sold separately) on the PlayZone Location to hear melodies, sounds and fun phrases from the show. The light will flash with the sounds. [image of playset with character on PlayZone and Bath Button]

4. TV Button

Press the TV Button to hear DJ Train Trax talk and play music. The light will flash with the music. [image of playset with TV Button]

5. SmartPoint™ Location

Place a SmartPoint™ character (sold separately) on the SmartPoint™ on the First Floor Base to hear fun phrases and sound effects. [image of playset with character on SmartPoint]

Care & Maintenance

1. Keep the unit clean by wiping it with a slightly damp cloth.
2. Keep the unit out of direct sunlight and away from any direct heat source.
3. Remove the batteries when the unit will not be in use for an extended period of time.
4. Do not drop the unit on hard surfaces and do not expose the unit to moisture or water.

Troubleshooting

If for some reason the unit stops working or malfunctions, please follow these steps:

1. Please turn the unit OFF.
2. Interrupt the power supply by removing the batteries.
3. Let the unit stand for a few minutes, then replace the batteries.
4. Turn the unit ON. The unit should now be ready to play again.
5. If the product still does not work, replace with an entire set of new batteries.

If the problem persists, please contact VTech Consumer Services Department and a service representative will be happy to help you.

Consumer Services

Creating and developing VTech® products is accompanied by a responsibility that VTech® takes very seriously. VTech makes every effort to ensure the accuracy of the information, which forms the value of its products. However, errors sometimes can occur. It is important for you to know that VTech stands behind its products and encourages you to call its Consumer Services Department with any problems and/or suggestions that you might have. A service representative will be happy to help you.

UK Customers:

Phone: 0330 678 0149 (from UK) or +44 330 678 0149 (outside UK)

Website: www.vtech.co.uk/support

Australian Customers:

Phone: 1800 862 155

Website: support.vtech.com.au

NZ Customers:

Phone: 0800 400 785

Website: support.vtech.com.au

Product Warranty/ Consumer Guarantees

UK Customers:

Read the complete warranty policy online at vtech.co.uk/warranty.

Australian Customers:

VTECH ELECTRONICS (AUSTRALIA) PTY LIMITED - CONSUMER GUARANTEES

Under the Australian Consumer Law, a number of consumer guarantees apply to goods and services supplied by VTech Electronics (Australia) Pty Limited. Please refer to vtech.com.au/consumerguarantees for further information.

CLASS 1 LED PRODUCT

Visit our website

Visit our website for more information about our products, downloads, resources and more.

www.vtech.co.uk

www.vtech.com.au

TM & © 2020 VTech Holdings Limited. All rights reserved. Printed in China. 91-003865-001 (UK)