Mi-Light AC Triac RF+Push Dimmer TRI-C1
Brand: Mi-Light / MiBOXERKey Features
- No need to change original electric circuit and install signal cable, low cost price, convenient to construct.
- Dim light through remote and Link code / Unlink code simply.
- Small and exquisite appearance, easy to insert into EU and USA standard wire boxes.
- Convenient to wire and install.
- Wide application for single color Triac dimmable LED light, traditional filament lamp, and halogen lamp.
- Support 2.4RF remote dimmable, control distance is 30m.
- Support Push dimmable.
- Trailing edge (ELV) phase-cut dimming.
- 0~100% stepless dimming technology.
- Set up minimum brightness via remote quickly.
- Includes switch for testing temperature and over-heat/load protection.
- Supports auto transmitting and synchronization for unlimited control distance.
- Output and input use screw connections for simple installation.
- PC shell is fire-resistant.
Technical Specifications
- Model No.: TRI-C1
- Input Voltage: AC100~240V 50/60Hz
- Output Voltage: AC100~240V
- Output Current: Max 1.36A
- Output Power: 150W @110V; 300W @220V
- Dim Method: RF wireless dimming, Push dimming
- Control Distance: 30m
- Working Temperature: -10~40°C
Connection and Installation
Connection Diagram: Connect the input AC power (L, N) to the input terminals of the dimmer. Connect the output load (L, N) from the dimmer's output terminals. The dimmer can be controlled via a push switch connected to the 'PUSH DIM' terminals (L1, NC, N).
Warning: Please ensure all cable connections are correct before powering on the supply to prevent damage to the dimmer.
Installation Diagram: The dimmer is designed to fit into standard bottom electrical boxes. Ensure the bottom case depth is over 50mm and the push switch is installed appropriately.
Operation Modes
Push Dimming
Short Press: Turns the light on or off.
Long Press: Provides stepless dimming. Press and hold to increase brightness, release and press again to decrease brightness.
Synchronization: If multiple dimmers are connected to the same auto-reset switch, long-press the push switch for 20 seconds to sync all lights to 100% brightness. It is recommended to connect fewer than 25 dimmers per auto-reset switch, with a maximum auto-reset switch cable length of 20m.
Pairing (Link Code)
To pair with K1 remote:
- Enter learning code mode on the dimmer (e.g., by short-pressing the 'SET' button once until the indicator flashes rapidly, or by cycling power off for 10 seconds and then on, or by short-pressing the push switch to the lighting-up mode).
- Press the 'SET' button on the remote three times within 3 seconds. Successful pairing is indicated by the light flashing slowly three times.
To pair with other remotes:
- Enter learning code mode on the dimmer.
- Press the 'Link/Unlink' button on the remote (e.g., ' | ' or 'ON') three times within 3 seconds. Successful pairing is indicated by the light flashing slowly three times.
Unpairing (Unlink Code)
To unpair K1 remote:
- Enter learning code mode on the dimmer (e.g., by long-pressing the 'SET' button for 3 seconds until the indicator flashes quickly).
- Press the 'SET' button on the remote five times within 3 seconds. Unpairing is indicated by the light flashing quickly ten times.
To unpair other remotes:
- Enter learning code mode on the dimmer.
- Press the 'Link/Unlink' button on the remote (e.g., ' | ' or 'ON') five times within 3 seconds. Unpairing is indicated by the light flashing quickly ten times.
Setting Minimum Brightness
This feature requires the dimmer to be paired with a remote first.
Using K1 Remote:
- Long-press the 'SET' button on the K1 remote for 3 seconds until the remote's indicator flashes once and the dimmer's indicator starts flashing.
- Short-press the 'SET' button on the remote to select one of 10 brightness levels: 3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%.
- Short-press any button on the remote (except 'OFF') or wait 10 seconds to confirm the setting. The lamp will return to its previous brightness before the setting.
Using Other Remotes:
- Long-press the 'OFF' button on the remote for 3 seconds until the remote's indicator flashes once and the dimmer's indicator starts flashing.
- Short-press the 'OFF' button on the remote to select one of 10 brightness levels: 3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%.
- Short-press any button on the remote (except 'OFF') or wait 10 seconds to confirm the setting. The lamp will return to its previous brightness before the setting.
Note: The master 'OFF' button can set the minimum brightness for all connected dimmers.
Auto Transmitting
The dimmer can transmit its signal to another dimmer within a 30-meter range. This allows for unlimited control distance if dimmers are installed every 30 meters.
Attention: All dimmers should be paired with one remote.
Compatible Remotes
The TRI-C1 dimmer is compatible with various Mi-Light and MiBOXER remotes, including models like FUT006, FUT007, B1/T1, B2/T2, K1, FUT087, and WL-Box1 (sold separately).
Important Notes and Warnings
- Ensure power is turned off during installation.
- Verify input voltage before installation.
- Do not disassemble the device unless you are a professional, as this may cause damage.
- Avoid installing near metal objects or magnetic fields, as this can affect control performance.
- The dimmer is not suitable for use in humid environments.
Certifications: CE, UKCA, RoHS.
Made in China.
Models: TRI-C1, AC Triac RF Plus Push Dimmer, TRI-C1 AC Triac RF Plus Push Dimmer, Triac RF Plus Push Dimmer, RF Plus Push Dimmer, Push Dimmer, Dimmer
