Anko Bluetooth Turntable

Notice

Please read user manual carefully before any operations, and keep it for records.

Package Includes

• 1 x Bluetooth turntable
• 1 x Adaptor
• 1 x User Manual

Specifications

• Product size: 35*25*12cm
• Adaptor input: 100-240V~ 50/60Hz
• Speaker output: 2x 0.4W
• Powered by adaptor (included)

Parts Identification

Detailed Parts List

Playing with Vinyl Disc

1. Remove the protective cap on the cartridge and stylus. Place the vinyl disc on the turntable platter.
2. Choose the desired playing speed using the speed selection switch (33.3, 45, or 78 RPM).
3. Switch the BT / PH switch (8) to PH mode and turn on the player.
4. Unlock the tonearm and lift it slowly.
5. Gently place the cartridge and stylus vertically onto the record groove; the turntable will start playing.
6. Auto Stop – ON: The turntable will stop automatically when the record has finished playing.
7. Auto Stop – OFF: The turntable will continue to spin until manually stopped.
8. After use, lift the tonearm and place it on the tonearm rest.
9. Place the protective cap back on the stylus and secure the tonearm rest.

Note: The turntable must be powered by the provided adaptor only.

Bluetooth Playing

1. Switch the BT / PH switch (8) to BT mode and turn on the player.
2. On your Bluetooth device, select "anko43413454" to connect to the player.
3. When successfully paired and connected, a beep will sound from the unit.
4. Rotate the volume knob (9) to adjust the volume.

After initial pairing, the unit will remain paired unless manually unpaired. If Bluetooth has been used before, the system will automatically search for the last connected device and reconnect if found.

NOTE:

• Only one Bluetooth device can be connected to the speakers at a time.
• If your device becomes unpaired or you are unable to connect, repeat the above steps.

AUX In

The device can play audio through the 3.5mm Aux In port (13).

Note: A 3.5mm aux cable is not provided.

AUX Out

The device can output audio through the 3.5mm Headphone jack (10).

Note: Headphones are not provided.

45 rpm Adapter / 7 Inch Record Adapter

Place this record adaptor on the turntable platter for playing 7-inch vinyl discs.

Connecting to External Speaker / Amplifier

You can connect the turntable to your existing Hi-Fi system or speaker. Connect the audio plugs from the Line Out ports (14 and 15) to the line input on your mixer or amplifier using an RCA cable (not supplied).

• Connect the Red plug (R/H channel) to the R/H channel input.
• Connect the White plug (L/H channel) to the L/H channel input.

12 Month Warranty

Thank you for your purchase. Your new product is warranted to be free from defects in materials and workmanship for 12 months from the date of purchase, provided that the product is used in accordance with accompanying recommendations or instructions.

This warranty is in addition to your rights under the Australian Consumer Law. For New Zealand customers, this warranty is in addition to statutory rights observed under New Zealand legislation.

Anko will provide a refund, repair (where possible), or exchange (availability dependent) for this product if it becomes defective within the warranty period. The business will bear the reasonable expense of claiming the warranty.

This warranty will no longer apply where the defect is a result of alteration, accident, misuse, abuse, or neglect.

Please retain your receipt as proof of purchase. For any difficulties with your product, warranty claims, or claims for expenses incurred in returning the product, contact the Customer Service Centre listed below for the entity from which you purchased the product.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Contact Information