User Manual for Daytech models including: CC21 Portable Wireless Chime Pager Doorbell, CC21, Portable Wireless Chime Pager Doorbell, Wireless Chime Pager Doorbell, Chime Pager Doorbell, Pager Doorbell, Doorbell
Daytech Manual | Caregiver Pager System User Manual
CALLTOU PRODUCT MANUAL – CallToU
INST-EN-CC21-T-20230227 User Manual for Portable Wireless Chime/ Pager/ Doorbell NOTE:We have paired them before shippment,you just plug and play! Thank you very much for purchasing our wireless door chime/pager/Doorbell system. This receiver is powered by 3 AAA batteries, it can be paired with call button,door open sensor ,push button to form a small standalone system, no network required, no cost. It is very convenient to carry with you at any time, no matter where you are you can receive alerts within the range of reception. Features: 1.4 Simple ringtones to choose.(Didi/DingDong/Hello Welcome/Alarm Sound) 2. Portable and back clip. 3. Power on/off 4.Alert mode: vibration, ringtone, flash 5. Volume: 5 level, 0-100DB 6. Memory function (the ringtone can be memorized after power off) 7.You can set different ring tone for different transmitter (call button/sensor/push button). 4 Working Modes: A. Ringtone+vibration B. Ringtone+colorful flash C. Ringtone+vibration+colorful flash D. Ringtone Installation: 1.Receiver Simply load the supplied 3 AAA batteries and select the ringtone, adjust the volum, push the sidebutton to choose the working mode(ABCD)you want, and it works. 2.Transmitter: 2.1.Door sensor You can install on the door,window,cabinet etc,when the door or window opened over 1.5cm(0.6inch),the indicator lights and sends signal to the receiver, then the receiver rings when it receive the signal. 2.2.Call Button/Push Button You can carry the button with you or install it on the wall, bedside etc, then press the button to send a signal,and the receiver rings when it receive the signal. Diagram: Back clip Volume Ringtone Mode selection Power Instructions: 1.Power ON/OFF Hold the power button for 3 seconds to turn on/off the receiver. 2.Volume adjust Press the volume button to adjust the volume level,from mute to 100db. 3.Change the ringtone/pairing Step1: Press the receiver's music key to select the ringtone. Step2: Press and hold the volume button of the receiver until the LED light flashes and emits a "ding" sound to enter the pairing mode(that means the receiver entered into the pairing mode,the pairing mode only last 8 seconds,it will automatically exit). Step3:Press the button or seperate the door sensor over 1.5cm(0.6inch) to send a signal,then the receiver will makes a "ding-ding" sound and flashes. Step4:Press the button or seperate the door sensor again to confirm the pairing. Clearing The Pairing/Reset Press and hold the receiver music key until the receiver's LED light flashes and emits a "ding" sound,wait about 10 seconds,the receiver emits a "ding", it means that the pairing has been reset. Door Sensor Installation Guide 1.Door contact sensor can adapt to many different types of door/window frames. Please ensure that the horizontal installation gap between them is less than or equal to 0.6 inches. Please do not install the door sensor on the iron door.(It will weak the range) 2.Fixing with double-side adhesive The surface of the door or window must be clean and dry to ensure the double-side adhesive properly. How To Set The Mute Mode: If you select mode A, you turn the volume to mute and the receiver will only vibrate to alert you. If you select mode B, you turn the volume to mute and the receiver will only flash to alert you. If you choose mode C, you turn the volume to mute and the receiver will only flash + vibrate. if you select mode D, you turn the volume to mute and the receiver does not have any alerts. How To Set The Emergency Alarm Mode. YouneedtoCLEARING THE PAIRING/RESET, select the alarm sound and pair the receiver with the transmitter according to the "Change the ringtone/pairing" operation. You can implement the emergency alarm function. (The default alert sound is "dingdong") You can set different alert modes, it's all up to your creative ideas, contact us via Amazon Email for any questions! Technical Parameter Temperature -30 C to +70 C Frequency 433.92MHz ±280KHz Receiver voltage 3 AAA batteries Transmitter voltage 23A12V alkaline zinc manganese battery/CR2450 battery Precautions *Please test the working distance between the receiver and thetransmitter before installation! *Please do not install the transmitter on the security door. Themetal will weaken the signal and affect the remote controldistance! *please do not install the receiver near TVs, induction cookers,microwave ovens and other electrical appliances with electromagnetic waves! *Please do not put the receiver and transmitter in water or fire toavoid accidents! *In case ofidle product for a long time, please take out the batteryto prevent the battery from dew and avoid malfunction!WPS 文字