Altec Lansing IMW1020 HydraMicro Wireless Speaker - Quick Start Guide

Welcome

This guide will help you get started with your Altec Lansing IMW1020 HydraMicro Everythingproof™ Wireless Speaker.

A Closer Look

The Altec Lansing IMW1020 features a robust design for portable audio. Key components include the speaker grille, control buttons, and an LED indicator light.

LED Indicator Light

• Flashing Green: Indicates the speaker is in True Wireless Stereo (TWS) pairing mode.
• Solid Green: Indicates two speakers are successfully paired in TWS mode.
• Blue Flashing LED: Indicates the speaker is in Bluetooth pairing mode.
• Solid Blue LED: Indicates the speaker is successfully paired via Bluetooth.
• Red Light: Indicates the speaker is currently charging.
• Light Off: Indicates charging is complete.

Speaker Controls

• Power Button:
  - Press & Hold [2 sec]: Turn ON/OFF.
  - Press: Answer/End Call.
  - Press & Hold [5 sec]: Disconnect Bluetooth.
  - Press & Hold [10 sec]: Reset all connections and power off.
• Volume Up / Next Track:
  - Press [+]: Increase volume.
  - Press & Hold [+]: Skip to the next track.
• Volume Down / Previous Track:
  - Press [-]: Decrease volume.
  - Press & Hold [-]: Go to the previous track.
• Play/Pause/Answer Call:
  - Press: Play or pause music.
  - Press: Answer or end an incoming call.
• Voice Assistant:
  - Press x2: Activate Siri or Google Assistant.
• Reject Incoming Call:
  - Press & Hold [2 sec] on Power Button.

Charging

Charging Time

It takes approximately 3-4 hours to achieve a full charge.

• (Red) = Charging
• (Off) = Charging Complete

Bluetooth Pairing

Pairing Mode

To enter Bluetooth pairing mode, press and hold the Power Button for 1-2 seconds. The LED indicator will flash blue.

Paired

Once successfully paired with your device, the LED indicator will show a solid blue light.

True Wireless Pairing (TWS)

To Pair Two Speakers

1. Turn on the first speaker and connect it with a Bluetooth-compatible device.
2. Turn on the second speaker. Press and hold the Power Button [1-2 sec] on the second speaker. Its LED indicator will flash green.
3. Press and hold the Power Button [1-2 sec] on the first speaker. The first speaker will then connect to the second speaker, allowing both to play in sync. The indicator LED on both speakers will illuminate solid green.
4. To end TWS pairing, press and hold the Power Button on either speaker.

Answering Calls & Voice Assistant

Answering Calls

Press the Power Button to answer or end an incoming call.

Voice Assistant

Press the Power Button twice ([Press x2]) to activate your device's voice assistant (Siri or Google Assistant).

Disconnect Bluetooth

Press and hold the Power Button for five seconds. The speaker will emit a beep to confirm disconnection.

Reset All Connections

Press and hold the Power Button for ten seconds. The speaker will power off, resetting all previous connections.

In the Box

• Altec Lansing IMW1020 HydraMicro Everythingproof™ Wireless Speaker
• USB-C Charging Cable
• Strap

Battery Performance

Overall battery performance can vary depending on usage settings and environmental conditions. For more detailed information, please visit www.alteclansing.com.

FCC Compliance Information

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Class B Digital Device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

Interference Correction Measures

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Limits

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Manufacturer Information

Sakar International Inc.
195 Carter Drive
Edison, New Jersey 08817, USA
Phone: 855-292-4087
Website: www.alteclansing.com