Vollrath Velocity Adjustable Breath Guard Installation Instructions

Vollrath Velocity Adjustable Breath Guard Installation Instructions

BEFORE YOU BEGIN

  1. Download the specification sheet from Vollrath.com. You will need to refer to this document for dimensions and NSF requirements.
  2. Know the countertop manufacturer's requirements for preparing and installing equipment into the countertop prior to starting installation. Countertop materials require specific preparation. Refer to the countertop manufacturer for instructions regarding the proper installation of equipment into the material.
  3. Know the NSF standards for breath guard installation applicable to your installation. The standards can be found on the NSF website.

BREATH GUARD WITHOUT HEAT OR LIGHT STRIPS

Breath guards without heat or light strips require assembly.

Mark and Drill the Mounting Holes

  1. Refer to the spec sheets for centerline and mounting option dimensions and requirements.
  2. Mark the mounting hole locations.
  3. Mount the uprights securely to the countertop, making sure they are square and parallel.

Diagram Description: A line drawing shows two upright supports for a breath guard, indicating where to mark mounting holes on a countertop.

BREATH GUARDS WITH HEAT OR LIGHT STRIPS

Breath guards with heat or light strips ship assembled.

  1. Place the assembled breath guard into position onto the mounting surface.
  2. Verify the breath guard uprights are parallel and square and the glass panels operate smoothly.
  3. Mark the mounting hole locations.
  4. Shift the breath guard to expose the hole markings.
  5. Drill the holes.
  6. Feed the electrical wires through the countertop before securing the breath guard.
  7. Attach the breath guard using appropriate hardware for the countertop surface and type of mounting.

Diagram Description: Three configurations of Vollrath breath guards are shown: one with a single straight glass panel, one with two angled side glass panels, and another variation of a single straight glass panel.

Install the Top Glass

  1. Place one gasket on the top of each upright standoff.
  2. Place the top glass panel on top of the uprights. Align the holes.
  3. Place one gasket over each hole in the top glass.
  4. Insert a plastic sleeve onto each thumbscrew and install them through each gasket and through the top glass. Tighten the thumbscrews to secure the top glass.

Diagram Description: A detailed illustration shows the process of installing the top glass panel onto the uprights, including the placement of gaskets and the use of thumbscrews with plastic sleeves.

Install the Long-Side Glass

  1. Rotate the adjustment mechanism so the standoffs are facing up, parallel to the countertop and locked into place.
  2. Attach the glass panel(s):
    • Place one gasket onto standoff.
    • Place the glass panel on top of the gaskets. Align the holes.
    • Place one gasket over each hole in the glass panel.
    • Install one thumbscrew through each gasket and through the glass panel. Tighten the thumbscrews to secure the panel.
  3. If applicable, repeat the steps for the other side.

Diagram Description: An illustration shows the long-side glass panel being attached to the standoffs, with steps detailing gasket placement and securing with thumbscrews.

Install the End Glass Panels

  1. Place one gasket on each standoff for the glass panel.
  2. Place the glass against the gaskets and standoffs.
  3. Place a gasket a hole in the end glass.
  4. Install one thumbscrew through the gasket and through the glass panel. Tighten to secure the end glass.
  5. Install the other three gaskets and thumbscrews.
  6. Repeat these steps for the other side end glass.

Diagram Description: A diagram illustrates the installation of the end glass panels, showing how to place gaskets and secure the panels with thumbscrews.

Test the Installation

The glass panel should rotate smoothly and without interference.

  1. Gently push up to unlock the glass panel.
  2. Press the release button.
  3. Lower the glass panel. Note: The glass panel rotates down in 90° increments from the starting position. You may need to push the release button more than once to lower the panel.
  4. Rotate the glass panel up through its full range. (Indications of "Click" are noted at various positions).
  5. Press the adjustment button and lower the glass panel. It will rotate 90° from the previous position and then lock into place.
  6. Press the adjustment button and lower the glass panel through all of the positions.
  7. If the adjustable panel binds, adjust and retighten the end frame nuts and screws or the thumbscrews.

Diagram Description: Illustrations depict the testing phase, showing how to unlock, release, and rotate the glass panel through its range of motion, with visual cues for locking points.

Models: SS-6BG-062S-HS Velocity Adjustable Breath Guard, SS-6BG-062S-HS, Velocity Adjustable Breath Guard, Adjustable Breath Guard, Breath Guard, Guard

File Info : application/pdf, 3 Pages, 943.25KB

PDF preview unavailable. Download the PDF instead.

VOL-SS-6BG-062S-HS im ?v=1709587308272

References

FrameMaker 2017.0.4 Acrobat Distiller 20.0 (Windows)

Related Documents

PreviewVollrath Velocity Adjustable Breath Guard Installation Instructions
Step-by-step installation guide for the Vollrath Velocity Adjustable Breath Guard, including assembly, testing, and troubleshooting. Learn how to properly install your breath guard for optimal performance and safety.
PreviewVollrath Cafeteria Breath Guard Installation Instructions
Step-by-step installation guide for Vollrath One Piece and Three Piece Cafeteria Breath Guards. Includes parts identification, assembly procedures, and safety notes.
PreviewVollrath Cafeteria Breath Guard Installation Instructions
Detailed installation guide for Vollrath One Piece and Three Piece Cafeteria Breath Guards, including part identification and step-by-step assembly instructions.
PreviewVollrath Cafeteria Breath Guard Installation Guide
Step-by-step installation instructions for Vollrath One Piece and Three Piece Cafeteria Breath Guards, including part identification and assembly details.
PreviewVollrath Installation Instructions: Cafeteria Breath Guards
Detailed installation instructions for Vollrath One Piece and Three Piece Cafeteria Breath Guards, including part identification and assembly steps for commercial food service environments.
PreviewVollrath Breath Guard Installation Instructions
Detailed installation guide for Vollrath one-piece and three-piece cafeteria breath guards, including step-by-step instructions and important notes for proper assembly.
PreviewVollrath Cafeteria Breath Guard Installation Instructions
Step-by-step installation guide for Vollrath One Piece and Three Piece Cafeteria Breath Guards, covering assembly of uprights, support tubes, guards, and shields using provided hardware.
PreviewVollrath Cafeteria Breath Guard Installation Instructions
Official installation guide from Vollrath detailing the setup process for both the one-piece and three-piece cafeteria breath guards. Includes important notes on assembly and part identification.