Osprey UNLTD AG 32 Owner's Manual

Overview

The Osprey UNLTD AG 32 is designed for optimal performance and comfort during outdoor adventures. It features a sustainable design approach using high-quality, environmentally friendly materials.

Shared Features

• Included ultralight raincover made with bluesign® approved fabric and DWR treatment made without PFAS, stored in a zippered pocket at the base of the pack.
• Dedicated external access hydration compartment with Osprey Hydraclip for easier reservoir hanging.
• Large zip access to the main compartment with a snag-resistant laminated zip flap.
• Easy-access upper zip pocket with a key clip for phone, wallet, and other valuables.
• Front compression panel with stretch side panels for securely storing overloads.
• Front zip pocket with snag-resistant laminated zip flap for maps and other essentials.
• Dual upper and lower quick-release compression straps.
• Ice tool loop with bungee tie-off.
• Stow-on-the-Go trekking pole attachment.
• Left-side zippered hipbelt pocket and standard stretch woven side pocket. Right-side extra-large reinforced stretch woven side pocket extends onto hipbelt for easy access to water bottle or extra gear/layers.

Fabric

• Main: bluesign® approved 100% recycled NanoFly™: 100D high-tenciity nylon (100% recycled) w/ UHMWPE ripstop, DWR treatment made without PFAS.
• Bottom: bluesign® approved 100% recycled NanoFly™: 100D high-tenacity nylon (100% recycled) w/ UHMWPE ripstop, DWR treatment made without PFAS.
• Main Liner: bluesign® approved NanoFly™: 210D high-tenacity nylon w/ UHMWPE ripstop, DWR treatment made without PFAS.

Product Promise

The Osprey UNLTD Series was designed without restrictions, featuring state-of-the-art fabrics, unique technology, and industry-first innovation. The Osprey UNLTD AG 32 combines cutting-edge comfort and market-leading technology for an uncompromising hiking experience.

Specs

Men's

Women's

Suspension/Carry

AIRSPEED™ ANTIGRAVITY SUSPENSION

• 4 mm powder-coated LightWire frame supports the load and shapes the backpanel for outstanding fit.

AIRSPEED BACKPANEL

• Injection-molded lumbar provides cushioning support, grip, and superior ventilation.
• 3D-tensioned breathable mesh backpanel ensures a supportive fit.
• Injection-molded ladder system provides 4" of easy, quick torso adjustability.

HARNESS

• AutoLift design automatically brings the load into balance against the back and sets the harness position in a single motion.
• Ventilated mesh yoke evenly distributes the load for comfort while maintaining breathability.
• Dual hydration hose clips.
• Adjustable sternum strap with rescue whistle.

HIPBELT

• EVA foam padded hipbelt integrates seamlessly into the mesh backpanel for ultimate comfort.
• Extendable, custom Fit-on-the-Fly Hipbelt™ offers a precise fit for varying waist sizes.
• Large, zippered pockets provide secure access to small essentials on the trail.
• ErgoPull closure provides leverage to ensure a snug fit and optimal load transfer.

Sizing / Fit

How to Measure Your Torso for Your Pack

1. Find Iliac Crest: Locate the top of your hip bone.
2. On Back of Neck, Find C7 Vertebrae: Touch your chin to your chest and feel for the large protruding bone at the base of your neck.
3. Measure From C7 Vertebrae to Iliac Crest: Measure the distance to determine your torso length.

Men's Torso Sizing

• S/M: 17-20" / 43-51 cm
• L/XL: 19-23" / 48-58.5 cm

Women's Torso Sizing

• WXS/S: 13-17" / 33-43 cm
• WM/L: 16-20" / 40.5-51 cm

Women's-Specific Fit

• Shorter torso length.
• Harness with curves designed to accommodate women's necks, shoulders, and chests.
• Hipbelt designed to wrap naturally around the curves of a woman's hips, offering better load stabilization and support.

Pack Fit Instructions

Position the Pack

Completely loosen the pack's hipbelt, harness, and load-lifter straps (if applicable). Load the pack with 10-20 lb/4-9 kg of gear. Put the pack on and ensure the hipbelt is centered and rests over the hipbone. The hipbelt padding should sit halfway above/below the hipbone.

Buckle Hipbelt

Buckle and tighten the hipbelt evenly using Osprey's cross-body ErgoPull. The hipbelt padding should wrap around the hips with approximately 1-3 in/2.5-6 cm of webbing between the buckle and the hipbelt when tightened.

Hipbelt Adjustment

If the hipbelt is too large or "tops out," or does not offer the preferred amount of coverage, the customer may need a different pack size, model, or adjustment.

Tighten Shoulder Strap

Tighten the shoulder harness straps by pulling them down and back.

Tighten Load Lifters (If Applicable)

Tightening the load lifters will pull the pack close to the body and help stabilize the load. If the torso length is adjusted correctly, the load lifters will sit between a 30- to 60-degree angle and align naturally with the shoulder straps.

Check Torso Length

Locate the harness yoke (where harness straps meet near the neck base). Locate the C7 vertebra (protruding bone at the neck base). The yoke should be 1 in/2.5 cm below the C7 vertebra.

Torso Length Adjustment Steps - AIRSPEED

1. Identify the two injection-molded adjustment ladders at the top corners of the tensioned mesh backpanel.
2. Each ladder has four cutouts. The pack harness passes through one cutout on each ladder, ending in a plastic harness toggle that sets the torso length.
3. To set a different torso length, reach behind the adjustment ladder on both sides and lever the harness toggles until they are fully extended and straight, allowing them to pass through the ladder cutout. Once done on both sides, the harness is free to slide up and down the LightWire frame.
4. Slide the harness up or down the LightWire frame to the appropriate torso length and re-insert the plastic harness toggles, curved side first, fully into the matching ladder cutout on both sides.
5. Ensure the plastic harness toggle is securely captured by the adjustment ladder and, under tension, is pulled up flat behind the backpanel. This ensures the toggle won't come out under weight and your torso adjustment is set.

Check Harness Fit

The harness straps should wrap fully around the shoulders with no gaps between the pack and back. The padded part of the shoulder straps should end at 2 in/5 cm or more below the armpits without topping out.

Harness/Shoulder Strap Adjustment

If the harness is too small or large, but the torso length is correct, the customer may need a different pack size, model, or adjustment.

Buckle the Sternum Strap

The sternum strap should be adjusted to approximately 2 in/5 cm below the collarbone.

Feature Details

Ultralight Raincover

Made with bluesign® approved fabric and DWR treatment made without PFAS.

1. Locate the raincover icon near the base of the pack.
2. Remove the raincover from its compartment and slip it over the top and bottom of the pack.
3. Tighten the cord lock at the bottom of the raincover to tension it into place.
4. To detach the raincover, unfasten the toggle from the cord loop.
5. Tip: To prevent mildew, allow the raincover to dry entirely before storing.

Reservoir Sleeve

Direct-access external hydration sleeve compatible with any reservoir up to 3L.

Upper Zippered Pocket

Easy-access upper pocket with a key clip keeps your phone, wallet, and other valuables handy.

Front Compression Panel

Features stretch side panels and a front zip pocket to securely store overloads.

Dual Compression Straps

Quick-release upper and lower compression straps provide added stability when the pack is not full or offer additional attachment points for carrying gear on the outside of the pack.

Trekking Pole Attachment

Osprey's Stow-on-the-Go trekking pole attachment is designed to quickly stash and carry trekking poles without taking off the pack.

1. Adjust the trekking poles to their minimum length (optional).
2. Locate the elasticized loop on the lower left side of the pack. While pulling the loop out from the pack, insert the basket end of the trekking poles into the loop.
3. On the left harness strap, locate the trekking pole icon. Pull up on the cord to open, place pole handles in the loop, and tighten with the cord lock to secure.
4. Reverse these steps to remove.

Ice Axe Loop

1. Slide the ice axe shaft through the top of the ice tool loop and flip the shaft up toward the top of the pack.
2. Loosen the bungee cord lock and route the tool handle through the bungee. Tighten the cord lock, nesting it into the Y-clip, to secure the tool in place.
3. Reverse above steps to remove.

Dual Hipbelt Pockets

Left-side zippered hipbelt pocket and standard stretch woven side pocket. Right-side extra-large reinforced stretch woven side pocket extends onto the hipbelt.