Homewerks Bath Fan with Bluetooth® Speaker and LED Light

For questions, problems, or missing parts, contact customer service at ? 1-877-319-3757, Monday - Friday, 7:30 a.m. - 4:30 p.m. CST. Read and save these instructions.

U.S. Pat. No. 9,398,357

The BLUETOOTH® word mark and logos are registered trademarks owned by BLUETOOTH SIG, Inc. and any use of the said mark by Homewerks Worldwide is under license. Other trademark and trade names are those of their respective owners.

Visit Homewerks.com for more information.

Product Specifications

UL Compliance

The Ventilation Fan Motor Wheel Assembly F is combined into Ventilation Fan Motor Housing F-1, which is mounted into the ceiling opening. These components comply with UL File 507: section 10.6, section 62.2.3, section 62.4.1, and section 64A.9.

FCC Compliance

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications made to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Package Contents

• Part A: Fan housing (1)
• Part B: Grille with BLUETOOTH® speaker and LED light (1)

Hardware Included

• AA: Wood Screw (Qty. 4)

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or install the product.

• Always disconnect the power supply prior to servicing the fan, motor or junction box.
• Follow all local building, safety and electrical codes, as well as NEC (National Electrical Code) and OSHA (Occupational Safety and Health Act).
• Electric Service supply must be 120 volts, 60 hertz.
• This product must properly connect to the grounding conductor of the supply circuit.
• Do not bend or kink the power wires.
• Do not use this fan with any solid state control device, such as a remote control, dimmer switch, or certain timers. Mechanical timers are not solid state devices.
• Do not install in a ceiling with insulation greater than R40.
• Duct work should be installed in a straight line with minimal bends.
• Duct work size must be the same size as the discharge and should not be reduced. Reducing the duct size may increase fan noise.
• This product is not intended for connection to rigid metal conduit. For use with flexible conduit only.

CAUTION:

• For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
• Not for use in kitchens.
• To reduce the risk of injury to persons, install the fan at least 7 feet (2.1m) above the floor.
• To reduce risk of fire and to properly exhaust air, be sure to vent air to the outdoors. Do not vent exhaust air into spaces within walls or ceilings, or into attics, crawl spaces, or garages.

WARNING:

To reduce the risk of fire, electric shock, or injury to persons, observe the following:

1. Use this unit in the manner intended by the manufacturer. If you have any questions, please call customer service.
2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and local code authorities.
5. When cutting or drilling into the wall or ceiling, do not damage electrical wiring and other hidden utilities.
6. To reduce risk of fire and to properly exhaust air, be sure to vent air to the outdoors. Do not vent exhaust air into spaces within walls or ceilings, or into attics, crawl spaces, or garages.
7. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.
8. This ventilation fan is intended to be installed at least 3.28 ft. (1 m) from the showerhead when installing over a bathtub or shower. Installation within a shower stall is not recommended for this unit, unless the 3.28 ft. (1 m) distance can be met.

CAUTION: Installation of this unit requires the power to be OFF until installation is complete. If you encounter issues with the unit not powering up, please review the troubleshooting section of the instruction manual.

If you require additional assistance, please call 1-877-319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday. DO NOT RETURN TO STORE.

Preparation

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts at 1-877-319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday.

Tools Required for Assembly (not included): Hammer, Flathead Screwdriver, Wire Connectors, Nails, Duct Tape, Phillips Screwdriver, and Utility Knife or Drywall Saw.

Helpful Tools (not included): Electric Drill, Drill Bits.

Dimensions

Wiring

All wiring must be connected for full functionality.

Wiring for 1 Switch Operation

This configuration connects the BLUETOOTH® speaker, LED light, and fan to a single switch. The diagram shows the wiring connections from the 120V/60Hz power source to the fan housing's junction box, including the motor, capacitor, automatic terminal switch, and connections for the speaker/LED and fan.

Wiring for 2 Switch Operation

This configuration uses one switch for the LED light and speaker, and a separate switch for the fan. The diagram illustrates the wiring from the 120V/60Hz power source to the fan housing, connecting the light kit, speaker/LED, and fan components separately.

Installation Instructions

New Construction Installation

Before Installation: Ensure electricity is shut off. Remove fuse or turn off circuit breaker.

1. Step 1: Place the fan housing (A) next to a ceiling joist. Ensure it is level and perpendicular to the joist, allowing for ceiling board thickness. Position the housing so its bottom edge is flush with the ceiling board. (Diagram shows housing positioned next to a joist).
2. Step 2: Before mounting, remove the duct connector for easier access to the mounting hole. This is done by inserting a flathead screwdriver between the connector and the fan housing metal and gently prying it away. (Diagram shows removing the duct connector).
3. Step 3: Mount the fan housing (A) to the joist using wood screws (AA) through the indicated holes on the metal tabs. Tighten until secure. (Diagram shows screws being inserted into the housing tabs).
4. Step 4: Replace the duct connector by hooking it onto one side of the metal flange in the fan housing opening and pressing the other side to snap it into place. Ensure all four metal flanges are inside the plastic duct connector. (Diagram shows the duct connector being reattached).
5. Step 5: Remove the wiring box cover from the fan housing (A). Pull house wires through the cover. Use quick connectors to connect house wiring from the wall switch to the fan housing (A). 14 AWG is the minimum conductor size for branch-circuit wiring. Refer to wiring diagrams on page 5 for proper connections. Push connections into the box and reattach the cover. (Diagram shows wiring box cover, quick connector, and wire connections). CAUTION: If wire colors do not match, consult a licensed electrician.
6. Step 6: Connect a 4-inch circular duct to the duct connector on the fan housing (A), securing with duct tape or a clamp. Vent the duct to the outside. Finish ceiling work, ensuring the ceiling hole aligns with the fan housing edge. (Diagram shows duct connection).
7. Step 7: Connect the BLUETOOTH® speaker and LED light connectors from the fan housing (A) to the grille (B). Push gray connectors firmly together and twist the plastic nut to secure. The grille (B) must be connected before turning on power. (Diagram shows connector alignment and securing).
8. Step 8: Attach grille (B) by pinching mounting springs and inserting them into the narrow rectangular slots in the fan housing (A). Turn on power and test the unit. (Diagram shows grille attachment with springs).

Existing Construction Installation

Before Installation: Ensure electricity is shut off. Remove fuse or turn off circuit breaker.

Installation requires accessible area above and existing duct/wiring.

1. Step 1: Remove the existing fan. (Diagram shows removing an old fan).
2. Step 2: Measure the opening to ensure it is large enough for the new fan housing (A) dimensions (7-1/2 in. x 7-1/4 in.). (Diagram shows measuring an opening).
3. Step 3: If not replacing an old fan, cut a 7-3/4 in. x 7-1/2 in. opening for the fan housing. (Diagram shows cutting an opening with dimensions).
4. Step 4: Detach the two grille mounting brackets by removing their screws. Save screws for reinstallation. (Diagram shows detaching mounting brackets).
5. Step 5: Slide and remove grille mounting brackets from the fan housing (A). Unplug the three-prong fan plug and pull the fan motor out. (Diagram shows removing brackets and fan motor).
6. Step 6: Remove the wiring box cover from the fan housing (A). Pull house wires through the cover. Connect house wiring from the wall switch to the fan housing (A) using quick connectors. Refer to wiring diagrams on page 18 for proper connections. Push connections into the box and reattach the cover. (Diagram shows wiring box cover and quick connector). CAUTION: If wire colors do not match, consult a licensed electrician.
7. Step 7: Connect a 4-inch circular duct to the duct connector on the fan housing (A), securing with duct tape or a clamp. Vent the duct to the outside. (Diagram shows duct connection).
8. Step 8: With wiring and duct connected, insert the fan housing (A) into the ceiling hole. Position it flush with the ceiling board. Mount the housing to the joist with three wood screws (AA) through the side holes. The housing must be flush for grille springs to engage. (Diagram shows inserting housing and mounting with screws).
9. Step 9: Plug the three-prong fan motor plug back into the fan housing (A). Place the fan motor back into the housing, aligning the duct. Replace grille mounting brackets and secure with screws. (Diagram shows plugging in motor and reattaching brackets).
10. Step 10: Connect the BLUETOOTH® speaker and LED light connectors from the fan housing (A) to the grille (B). Push gray connectors firmly together and twist the plastic nut to secure. The grille (B) must be connected before turning on power. (Diagram shows connector alignment).
11. Step 11: Attach grille (B) by pinching mounting springs and inserting them into the narrow rectangular slots in the fan housing (A). Turn on power and test the unit. (Diagram shows grille attachment with springs).

Pairing Your Bluetooth® Device to the Speaker

To play personal music files, you need a wireless BLUETOOTH® device. Set your device to a midrange volume before connecting. Follow your device's instructions to make it discoverable or search for accessories. This may require a passkey or PIN. Optimal volume setting is 70% or lower; higher settings may cause distortion.

Bluetooth® Connection for One Switch Installation:

Your LED light, speaker, and bath fan will be controlled by the same switch.

1. After wiring, turn on the power. The BLUETOOTH® speaker enters connecting mode.
2. From your device's home screen, go to Settings > BLUETOOTH® to search for the speaker.
3. Select the Homewerks™ speaker. Enter the passkey or PIN if prompted.
4. Once paired, use the BLUETOOTH® speaker to play audio.
5. To turn off BLUETOOTH® connectivity, disconnect the speaker from your mobile phone or turn off the LED light, speaker, and fan switch.

Bluetooth® Connection for Two Switch Installation:

The bath fan is controlled by one switch, and the LED light and speaker by a second switch.

1. After wiring, turn on the switch connected to the LED light and speaker. The BLUETOOTH® speaker enters connecting mode.
2. From your device's home screen, go to Settings > BLUETOOTH® to search for the speaker.
3. Select the Homewerks™ speaker. Enter the passkey or PIN if prompted.
4. Once paired, use the BLUETOOTH® speaker to play audio.
5. To turn off BLUETOOTH® connectivity, disconnect the speaker from your mobile phone or turn off the LED light, speaker, and fan switch.

REMINDER:

• This fan does not include a switch.
• For one-switch installation, the LED light, speaker, and fan operate together.
• For two-switch installation, one switch controls the LED light and speaker, and the other controls the fan.

Care and Cleaning

CAUTION: Before cleaning, disconnect power by turning off the breaker or removing the fuse.

Routine maintenance should be done at least once a year.

• Never use solvents, thinners, or harsh chemicals.
• Do not allow water to enter the motor.
• Do not immerse metal parts in water.
• Do not immerse resin parts in water above 140°F.
• Do not immerse the BLUETOOTH® speaker in water.

Cleaning Steps:

1. Remove the grille (B) by squeezing mounting springs and pulling down. Disconnect connectors by twisting gray ends to unlock before separating. Wipe grille (B) with a damp cloth. (Diagram shows grille removal and connector disconnection).
2. Remove dust and dirt from the fan housing (A) with a vacuum cleaner. (Diagram shows vacuuming the housing).
3. Wipe the fan housing (A) with a damp cloth and dry it. (Diagram shows wiping the housing).
4. Reconnect the BLUETOOTH® speaker and LED light connectors from the fan housing (A) to the grille (B). Push connectors firmly and twist the plastic nut to secure. (Diagram shows connector reconnection).
5. Attach grille (B) by pinching mounting springs and inserting them into the narrow rectangular slots in the fan housing (A). Turn on power. (Diagram shows grille attachment with springs).

Troubleshooting

Warranty

Fan - Limited 3-Year Warranty: Homewerks warrants the fan against defects in materials or workmanship for three years from the date of ownership. This warranty does not cover abuse, alteration, damage, misuse, cutting, or wear. It does not cover commercial applications. Use only manufacturer-supplied parts; non-genuine parts void the warranty. Homewerks disclaims all other implied or express warranties. This warranty is limited to replacement of defective parts; labor charges and consequential damages are excluded. Any damage from neglect, misuse, accident, improper installation, or use other than intended voids the warranty.

BLUETOOTH® Speaker - Limited 1-Year Warranty: Homewerks warrants the BLUETOOTH® speaker against defects in materials or workmanship for one year from the date of ownership. This warranty does not cover abuse, alteration, damage, misuse, cutting, or wear. It does not cover commercial applications. Use only manufacturer-supplied parts; non-genuine parts void the warranty. Homewerks disclaims all other implied or express warranties. This warranty is limited to replacement of defective parts; labor charges and consequential damages are excluded. Any damage from neglect, misuse, accident, improper installation, or use other than intended voids the warranty.

Shipping costs for warranty returns must be paid by the customer. Inquiries can be directed to 1-877-319-3757.