Instruction Manual for ELECCTV models including: BW4PLUS, BW4PLUS 2K QHD Solar Security Cameras, 2K QHD Solar Security Cameras, QHD Solar Security Cameras, Solar Security Cameras, Security Cameras, Cameras
ELECCTV 2K QHD Solar Security Cameras Wireless Outdoor WiFi, 12000mah Battery, IP66 Waterproof, Two-Way Audio, Color Night Vision, Motion Sensor-4PACK BW4PLUS with Solar Panel : Electronics
Enable the location service of your phone, and allow the O-KAM. APP to access the location. Confirm the WiFi and enter the password. * Make sure the Wi-Fi is ...
Wire-Free Camera Operation Instruction BW4-Plus) Customer Service Claim 1-year warranty for your device Please email us: aftersale@rraycom.com Phone: +1 2027384449 (Sun. - Thur. 8pm - 12pm) Facebook Rraycomz@gmail.com Packing List Camera *1 Bracket *1 USB Cable *1 Instruction*1 Mounting Kit *1 Appearance Indicator light Photosensitive MIC PIR BW4Plus 01 At the bottom OFF/ON USB 5V 1.5A Charging TF card Reset BW4Plus Speaker 02 At the bottom OFF/ON Reset TF card * 5V 1.5A Power adaptor Only CautionUse a power adapter with a power rating of 5V 1.5A or below. Indicator light definition Reset Green light flashes Charging Red light Fully Charged Off No network Blue light flashes Wifi connected Blue (when it wakes up) Sleep Off 03 Quick start Power-on Press and hold the power button until you hear the prompt, and the indicator light flashes blue slowly. Reset Press and hold the reset button for about 3 seconds, the green indicator light flashes, and the camera finish reset when the blue light is on. Step-1 >>> Download the APP Scan the QR code to download the APP. Or search for "O-KAM" to download through the app store (Google play/ APP Store). O-KAM 04 Step-2 >>> APP account registration Click "Register now" at the login interface -- Select the address -- Enter your phone number -- Get the verification code. After entering the verification code you need to set the password and click Finish. 05 Step-3 >>> Add cameras Log in and click "Add" button found at the "Home" interface or click the " " in the upper right corner. 06 Step-4 >>> Add cameras At the QR code scanning interface, scan the QR code on the camera. 07 >>> >>> Switch the camera "On". (No need for "Long press") Click "Next" when the indicator light flashes in blue slowly. Confirm that the camera is ready for WiFi configuration when the indicator light flashes in blue slowly. And click "Next" 08 >>> Enable the location service of your phone, and allow the O-KAM APP to access the location. Confirm the WiFi and enter the password. * Make sure the Wi-Fi is 2.4Ghz. WiFi password case sensitive. 2.4Ghz 5 Ghz 09 >>> The APP will automatically generate a QR code. Point the camera lens at the QR code and keep it at a distance of 6-8 inches. You' ll hear a beep and voice prompt when it's scanned successfully. 6-8 INCHES 10 >>> When the device is connected to the WiFi, name the camera and click "Bind Now". 11 >>> Please take the camera and phone to the location where you're going to install the camera, and then click "Next" to test the signal strength. Make sure there is strong WiFi signal strength at the location. 12 Step-5 >>> APP function introduction Home introduction. Multi-device view Add device Cloud service System settings Share camera Do not disturb mode WiFi display 13 Step-6 >>> Monitoring settings Enter system settings " "-monitoring function Tap on the "Device Health"- "Firmware"to update (Suggested) 14 Step-7 >>> Share the device Enter the system settings " "- Share Sharing method: Share the QR code to a user. The other user adds the camera by scanning the QR code;The QR code is valid for 30 minutes, and one QR code can only be shared with one user. Generate more QR codes for more members. Maximum of 4 people can live view. 15 Tutorial Videos Please scan the QR code below 16Adobe PDF library 16.03 Adobe Illustrator 26.0 (Windows)