Electrorad Touch E3 Installation and Operating Manual

Advanced Heating Technology

FOR THE INSTALLER

Main Characteristics

Touch screen (4 inches)
Interface via internet: WiFi 2.4 GHz (not 5.0 GHz)
Wall mountable with power supply 85-265V (50-60)Hz
Can be placed on the table with supplied bracket and mini USB power supply (5V)
Battery operation (only for settings)
RF Communication with other devices
Multiple heating device control
SD Card update
Intuitive menus for device management

Note: Charge the Touch E3 for at least one hour before pairing the devices already mounted.

Connecting to Touch E3

The Touch E3 can manage up to 50 rooms (zones) with one master radiator in each room, and up to 50 slave radiators distributed among the masters.

Examples:

a) 50 zones with 1 master and 1 slave in each, total 100 radiators
b) 1 zone with 1 master and 50 slaves, total 51 radiators

It is recommended to limit the number of slaves to 10 in one zone.

Technical Specifications

TEMP. PRECISION:	0.1°C
ENVIRONMENTAL CONDITIONS:	Operating temperature: 0°C to +40°C
ENVIRONMENTAL CONDITIONS:	Shipping and storage temp.: -30°C to +50°C
SETTING TEMPERATURE RANGE:	Comfort mode: +5.5°C to +30°C (must be higher than reduced mode)
	Reduced mode: +5°C to +19°C (must be lower than Comfort mode)
	Frost protection mode: +0.5°C to +10°C
ELECTRICAL INSULATION:	Class II
ELECTRICAL PROTECTION:	IP 30
RADIO FREQUENCY:	Range outside: 868 MHz, <10mW (200 m)
RADIO FREQUENCY:	Range indoor (typical): Around 15 m
WIFI FREQUENCY:	2.4 GHz (not 5.0 GHz)
SOFTWARE VERSION:	Found in Main menu (xx.xx) or WiFi menu (xxxx XX.XX)
POWER SUPPLY:	85-265V 50-60 Hz
CE DIRECTIVES:	Designed in conformity with European Directives: LV Directive 2006/95/EC, EMC Directive 2004/108/EC, R&TTE Directive 1999/5/EC, RoHS 2011/65/EU

Wall mounting

Connect the power supply as described below. Electrical installation must comply with local/national regulations. Connection should be made by a qualified electrician.

Step 1: Screw the power supply onto the wall. Ensure the tab is located at the top. (Dimensions: 60 MM)

Step 2: Put the switch into the ON position using a small pin.

Step 3: Mount the Touch E3 onto the power supply and slide it down until it stops. The Touch E3 is now ready for use.

Table installation

Step 1: Connect the mini USB cable and charger to the Touch E3.

Step 2: Mount the Touch E3 onto the bracket by sliding it down until it stops.

Step 3: Put the switch into the ON position using a small pin. The Touch E3 is now ready for use.

FOR THE INSTALLER AND USERS

General Pictograms

🏠 To return to the "Start screen"
↩︎ To return to the previous screen
Buttons with a red dot require a long press.

Setting Language, Time and Date

Press "Main menu" button A.
Press "Set language" button D. The flag of the current language is displayed.
Press "User settings" button F to set the current time and date.

Create House

Press "Main menu" button A.
Press the "Parameter settings" button I (long press).
Press the "House creation" button.
Create all the rooms (or zones).

Room Menu Labels:

a: Current room name
b: To change the current room name
c: To add a room
d: To delete the current room
e: Room selection

Pairing Radiators

Press "Main menu" button A.
Press the "Parameter setting" button I (long press).
Select radio pairing.
Choose device, press "Heating".
Select room.

Confirmation:

Press "Green check" button to confirm.
Device (Radiator or Remote Control) to measure the temperature must be paired first in this zone.
Press "Green check" button to confirm.
Put the device (radiator or remote control) in pairing mode. See device leaflet or manual.

Example:

Press and hold the "OK" key for 5 seconds for Wireless Radio Initialisation (pairing). Press "OK" to enter this initialisation sequence.

Select communication type with "+" or "-" and validate by pressing "OK":

rF.un: Unidirectional communication; thermostat receives orders from an RF central programmer.
rF.bi: Bidirectional communication; thermostat communicates state and power consumption to the Touch E3.

The backlight will switch off, and digits will cycle, showing the thermostat is waiting for a radio link signal. Press "◀" to cancel radio initialisation. When the signal is received, pairing is saved, and it returns to Auto mode.

Installation Types (Type 1)

TOUCH E3 controls a MASTER radiator, which can in turn control SLAVE 1 and SLAVE 2 radiators.

Define a Mode to a Zone/Room

From the "Start screen", press "Home" button B.
Press "Current mode" button 3 (See "Heating Device Management" section, p 15).
Press the desired mode button (g Comfort, h Auto, i Reduced, j Timer, k Frost protection, m Off).
Press the "Green check" button 4.

Mode Descriptions:

Comfort mode: Sets the comfort temperature.
Auto mode: Room temperature follows the selected program.
Reduced mode: Sets the reduced temperature.
Timer mode: Define time and temperature. Press the "Black hour glass" button to define time, then "White hour glass" button to define temperature.
Frost protection mode: Sets the frost protection temperature.
Off mode: Radiators do not heat. WARNING: Water pipes may freeze. Radiators are still connected to electrical supply.
Program Setting: Selects the program for Auto mode.

Defining Temperatures for Each Zone

From the "Start screen", press "Home" button B.
Press "Current mode" button 3.
Press the "Comfort" or "Reduced" button.
Press "Green check" button 4 to confirm.
Press "+" or "-" to set the temperature.
Press "Heating" button 1 to save the temperature.
Press arrows 2 to change room or button 9 to see all rooms. Repeat from step 02.

Define Weekly Program for Each Room

You can SELECT a pre-defined program, CREATE a new program, or EDIT an existing program.

TO SELECT:

From the "Start screen", press "Home" button B.
Press arrows 2 to change room or button 9 to see all rooms.
Press "Current mode" button 3.
Press "Program Setting" button m.
Press "Select" to choose from 5 pre-defined programs.
Press "Green check" button 4 to select.
Warning sign: press "Green check" button 4.
Press the "back" button.
Press the "clock" button.
Press "Green check" button 4.

TO CREATE:

From the "Start screen", press "Home" button B.
Press arrows 2 to change room or button 9 to see all rooms.
Press "Current mode" button 3.
Press "Program Setting" button m.
Press "Create" to define your own program.
Select days to program. Day status: Red (not programmed), Grey (selected), Green (programmed).
Initially, reduced mode is set for 24h (15-minute periods). Press "Comfort" or "Reduced" buttons to create the program. Use arrow buttons 2 to move the cursor.
Press "Green check" button 4 to confirm days and repeat for all days.
Once all days are green, press "Green check" button 4.
Warning sign: press "Green check" button 4.
Press the "back" button.
Press the "clock" button.
Press "Green check" button 4 to confirm.

TO EDIT:

From the "Start screen", press "Home" button B.
Press "Current mode" button 3.
Press "Program Setting" button m.
Press "Edit" button.
Select the day to change.
Make desired changes.
Press "Green check" button 4.
Warning sign: press "Green check" button 4. Repeat from step 04 if needed.
Press the "back" button.
Press the "clock" button.
Press "Green check" button 4 to confirm.

FOR USERS

Start Up Screen

K Day and date.
L Displays time or temperature of a selected room. Change by pressing the temp/time value and choosing the desired room's temperature.
M Screen lock. Enter default code "1066" or configured code.
N Error indicator (visible when active). Access list by pressing the icon.
O Powered by battery (visible when disconnected). Connect to power supply during normal use.
B House/Rooms access (view only when screen is locked).
P Holiday mode (visible when active).
A To access "Main menu".

Main Menu

C Consumption statistics menu: Press "heating" to check consumption per day/week/month/year. Press "information button" for graphical display. Press "trash can" button (long press) to delete history.
D Language setting.
E Mode menu: Set all radiators to the same mode. Press button until desired mode appears. Press "Green check" button. It may take minutes for units to receive new information.
F User settings: Set Date and time, Summer/Winter time, Temperature/Time units, Background/Button colour, Backlight, Screen, WiFi, Reset to factory settings.
H Holiday mode: Define time and date of departure and return. Define mode for whole installation. Press "Green check" button.

Installation (House creation menu)

House creation (See "Create house" section, p 6)
Radio pairing (See "pairing radiators" section, p 6)
Screen lock (See "Other functions for the installer" section, p 17)

Other Functions

Delete a device: Press "Delete a device", then "heating" button. Use arrows to scroll and select device. Press "Green check" to confirm. Note: To ensure correct device deletion, identify it first. If the first device in a room is deleted, all devices in that room will be deleted.
Delete all devices: Press "Delete all devices", then "Green check" to confirm or "Red cross" to decline.
Identify a device: Press "Identify a device", then "Radio button". Make the device send a radio message. Note the ID-number. Repeat to confirm accuracy.
Edit device information/settings (long press button with red dot): Device name, Power, Set front panel max surface temperature level, Heating rate maximum level. Select P1, P2, or P3 (first radiator must have same or higher value). Press "Green check" to confirm. For double radiators, change to sequential control. Select "No" (default) for even heating, "Yes" for sequential heating. Press "Green check" to confirm.
Screen lock: Press "Screen lock" button. Enter 4-character code. Press "Green check" to confirm. Default code: 1066.
Heating settings: Set Minimum and Maximum allowed temperatures per room. Press "Heating Settings" button, then a room button.
WiFi settings (See "WiFi settings" section, p 18).
General factory default: All data erased except WiFi settings. Press Red "Reset" button (long press), then "Green check" to confirm or "Red cross" to decline.
Update firmware: Insert SD card with new firmware. Press "Update firmware", then "Green check" to confirm or "Red cross" to decline.

WIFI SETTINGS

Connect the Touch E3 to Your WiFi

Press "Main menu" button A.
Press "Parameter setting" button I (long press).
Select "WiFi settings" button.

You can enter WiFi settings manually or perform a WiFi scan.

Perform a WiFi scan:

Press "Research networks" button. Repeat if necessary.
Select your desired WiFi network.
Select encryption type (e.g., WEP, WPA).
Enter key code / password.

Enter the WiFi setting manually:

Enter your WiFi network name (SSID).
Select encryption type (e.g., WEP, WPA).
Enter key code / password.

A green flag indicates a successful WiFi connection. The "Reset" button (long press) can reinitialise WiFi settings.

Access to Touch E3 via PC

Access TOUCH E3 from http://www.lvi.eu/clevertouch (or http://www.lvifrance.fr/clevertouch in France).
Create an account.
Validate your email.

A pairing code (valid 24h) will be sent to your email. Enter this code in the Touch E3 "WiFi menu" under "Internet access password". A green flag indicates connection.

Access to Touch E3 via Smartphone

Download the free App "CLEVER TOUCH" from Appstore or Google play.
Create an account.
Validate your email.