Introduction
This document provides instructions for the DeLonghi ECAM22110 Fully Automatic Coffee Center. Please keep these instructions for future reference.
Electronic Characteristics: 120V ~60 HZ 1250 W
Register your product online at www.delonghiregistration.com.
For a list of service centers near you, visit www.delonghi.com.
Parts Identification
Main Unit (A)
- A1: Water tank
- A2: Coffee bean container lid
- A3: Coffee bean container
- A4: Drip tray
- A5: Used coffee grounds container
- A6: Drip tray grid
- A7: Coffee dispensing spout
- A8: Power switch [power symbol]
- A9: Grinder adjustment knob
- A10: Grinder
- A11: Grinding adjustment dial
- A12: Front panel
- A13: Brew unit
- A14: Brew unit compartment
- A15: Drip tray assembly
- A16: Drip tray
- A17: Drip tray support
- A18: Steam/hot water wand
- A19: Milk carafe attachment (or similar)
Control Panel (B)
- B1: Display and indicator lights (ECO, temperature, descaling ❗)
- B2: Power button [power symbol]
- B3: Coffee strength selection
- B4: Coffee size selection
- B5: Coffee volume dial (MIN to MAX)
- B6: Coffee bean/ground coffee selector
- B7: Hot water/steam button
- B8: Pre-ground coffee function button
- B9: Coffee dispensing button
Accessories (C)
- C1: Water filter
- C2: Drip tray
- C3: Water tank
Operating Instructions
Step 1A/1B: Initial Setup.
Place the machine on a flat surface. Insert the water tank (A1) and drip tray (A4/A16). Ensure the used coffee grounds container (A5) is in place.
Step 2: Fill Water Tank.
Remove the water tank (A1), fill it with fresh water up to the MAX level ?, and reinsert it.
Step 3: Fill Coffee Bean Container.
Open the coffee bean container lid (A2) and fill the container (A3) with coffee beans ☕. Close the lid.
Step 4: Power On and Initialisation.
Connect the power cord and press the power button (B2). The machine will perform an initialisation sequence. Wait for the lights to stabilize.
Step 5: Select Coffee Strength and Size.
Use buttons B3 and B4 to select desired coffee strength and size. Adjust coffee volume using dial B5.
Step 6: Select Coffee Type.
Use button B6 to choose between whole beans ☕ or pre-ground coffee. If using pre-ground coffee, use button B8.
Step 7: Dispense Coffee.
Place a cup under the coffee dispensing spout (A7). Press button B9 to dispense coffee.
Step 8: Hot Water/Steam.
To dispense hot water or steam, press button B7. Use the steam/hot water wand (A18) accordingly.
Step 9: Adjust Grinding.
Use the grinder adjustment knob (A9) and dial (A11) to set the desired grind fineness. Adjust the coffee volume with dial B5.
Step 10: Filling Water Tank (Detail).
Illustration shows filling the water tank (A1) up to the MAX level ?.
Step 11: Inserting Water Tank.
Illustration shows reinserting the filled water tank (A1) into the machine.
Step 12: Removing Drip Tray.
Illustration shows removing the drip tray (A4/A16) for emptying and cleaning.
Step 13: Emptying Used Coffee Grounds Container.
Illustration shows removing and emptying the used coffee grounds container (A5).
Step 14: Using Pre-ground Coffee.
Illustration shows inserting pre-ground coffee into the designated compartment (likely within the brew unit area).
Step 15: Dispensing Coffee (First Cup).
Illustration shows the machine dispensing coffee into a cup.
Step 16: Dispensing Coffee (Second Cup).
Illustration shows the machine dispensing coffee into a second cup.
Step 17: Machine Ready.
Illustration shows the machine after coffee dispensing, ready for next use.
Step 18: Control Panel Overview.
Illustration of the control panel (B) with buttons and dials.
Step 19: Inserting Pre-ground Coffee.
Illustration shows adding pre-ground coffee into the machine's compartment.
Step 20: Using the Steam Wand.
Illustration shows using the steam wand (A18) to froth milk.
Step 21: Removing Brew Unit.
Illustration shows the process of removing the brew unit (A13) for cleaning.
Step 22: Cleaning Brew Unit.
Illustration shows cleaning the brew unit (A13) under running water.
Step 23: Installing Water Filter.
Illustration shows inserting a water filter (C1) into the water tank (A1).
Step 24: Emptying Drip Tray and Grounds Container.
Illustration shows removing and emptying both the drip tray (A4/A16) and the used coffee grounds container (A5).
Step 25: Inserting Brew Unit.
Illustration shows reinserting the cleaned brew unit (A13) into its compartment (A14).
Step 26: Reattaching Drip Tray.
Illustration shows reattaching the drip tray (A4/A16) after cleaning.
Step 27: Dispensing Coffee.
Illustration shows the machine dispensing coffee.
Step 28: Dispensing Hot Water.
Illustration shows the machine dispensing hot water.
Step 29: Cleaning the Brew Unit Compartment.
Illustration shows cleaning the area where the brew unit is housed.
Step 30: Emptying Coffee Grounds Container.
Illustration shows emptying the used coffee grounds container (A5).
Step 31: Water Level Indicator.
Illustration showing water levels in the tank (A) and possibly a related component (B).
Step 32: Water Flow/Level.
Illustration indicating water flow or level in a system.
