50W ZigBee CCT LED Driver (Constant Current)

Important Information

Important: Read All Instructions Prior to Installation.

Function Introduction

8-230V Push Switch Input: Connects to an 8-230V push switch. Press the switch to turn the load on/off. Press and hold the switch to increase/decrease light intensity.

ZigBee LED Driver: The main unit. Features AC input, push switch input, and 2-channel CCT output.

AC Input: Supports AC 200-240V input.

Program Key: Short press to switch on/off load, press and hold down to increase/decrease light intensity.

DIP Switches: 8 DIP switches are available to set the operation current.

Diagram Description: Diagram shows the '8-230V Push Switch Input' connected to the 'ZigBee LED Driver'. The driver has terminals for AC INPUT (200-240V), Push Switch Input, Program Key, and two output channels labeled '2 channels CCT output' with connections for LED+ CW- and WW-. DIP switches (1-8) are visible on the driver for setting operation current.

Product Data

Rated Power: 50W max.

Voltage Range: 200-240V AC

Frequency: 50/60Hz

Power Factor (Typ.): >0.9

Efficiency (Typ.): 87% @ 230VAC

Input Current: 0.27A @ 230VAC

Inrush Current (Typ.): COLD START Max. 2A @ 230VAC

Protection

• Short Circuit: Yes, auto recovery after fault removed.
• Over Voltage: Yes, auto recovery after fault removed.
• Over Temperature: Yes, auto recovery after fault removed.

Environment

• Working Temp.: -20℃~+45℃
• Max. Case Temp.: 85℃ (Ta="45℃")
• Working Humidity: 10%~95% RH non-condensing
• Storage Temp. & Humidity: -40℃ ~ +80℃, 10%~95% RH

Diagram Description: A visual representation of 8 DIP switches labeled 1 through 8. Below are tables showing combinations of DIP switch settings (represented by filled and empty circles) corresponding to selectable output currents ranging from 250mA to 700mA in the first set, and 800mA to 1500mA in the second set.

Safety & EMC

Safety Standards: ENEC EN61347-1, EN61347-2-13 approved

Withstand Voltage: I/P-O/P: 3.75KVAC

EMC Emission: EN55015, EN61000-3-2, EN61000-3-3

EMC Immunity: EN61547, EN61000-4-2,3,4,5,6,8,11, surge immunity Line-Line 1KV

MTBF: 190300H, MIL-HDBK-217F @ 230VAC at full load and 25℃ ambient temperature

Dimension: 210*50*32mm (L*W*H)

Key Features

• Dimmable LED driver for tunable white.
• ZigBee CCT LED light device based on ZigBee 3.0 protocol.
• Max. output power 50W total.
• 2 channels 250-1500mA constant current output, DIP switches to select multi operation current.
• Class II power supply, full isolated plastic case.
• Built-in active PFC function, high power factor and efficiency.
• Deep and smooth dimming to 0.1%.
• Enables control of ON/OFF, light intensity, and CCT of connected CCT LED lights.
• ZigBee end device that supports Touchlink commissioning.
• Can directly pair to a compatible ZigBee remote via Touchlink.
• Supports find and bind mode to bind a ZigBee remote.
• Supports Zigbee Green Power and can bind max. 20 Zigbee Green Power switches.
• Compatible with universal ZigBee gateway products.
• Compatible with universal CCT ZigBee remotes.
• With Push Dim function, can be controlled by universal 8-230V input single wire push switch.
• Waterproof grade: IP20, suitable for indoor LED lighting applications.
• 5 years warranty.

Safety & Warnings

• DO NOT install with power applied to the device. [warning]
• DO NOT expose the device to moisture. [warning]

Wiring Diagram

The wiring diagram shows the connection points for AC input (L/N), an 8-230V push switch input, and the ZigBee LED Driver. The driver has terminals for Push Switch Input, Program Key, and two output channels: CW- (Cool White) and WW- (Warm White), along with V+ terminals for both channels. The output connects to a CCT color LED light.

Diagram Description: Wiring diagram illustrating the connection of the ZigBee LED Driver. AC power input (L and N) is shown. A 'PUSH' switch connects to the driver's input. The driver has terminals labeled 'V+' and 'CW-' for one channel, and 'V+' and 'WW-' for the second channel, connecting to a 'CCT color LED light'.

Operation

1. Wiring: Ensure wiring is done correctly according to the connection diagram.
2. ZigBee Communication: This ZigBee device is a wireless receiver that communicates with ZigBee compatible systems via radio signals.

3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)

1. Remove from Previous Network: If the device is already added to a Zigbee network, remove it first. Refer to "Factory Reset Manually".
2. Add Device: From your ZigBee Controller or hub interface, select "add lighting device" and enter Pairing mode as instructed by the controller.
3. Initiate Pairing: Re-power the device. The connected light will flash twice slowly, indicating it's in network pairing mode. This mode lasts for 15 seconds. Repeat the operation if needed.
4. Confirmation: The connected light will blink 5 times and then stay solid. The device will appear in your controller's menu for control.

Diagram Description: Diagram shows the ZigBee LED Driver connected to AC Power (200-240V) and an 8-230V Push Switch Input. Output terminals are labeled V+, CW-, WW-. This diagram illustrates the device setup for network pairing.

4. TouchLink to a Zigbee Remote

Method 1: Short press the "Prog" button 4 times (or re-power the device 4 times) to start Touchlink commissioning immediately (180S timeout). Repeat if necessary.

Method 2: Re-power the device. Touchlink commissioning starts after 15S if not added to a Zigbee network (165S timeout), or immediately if already added (180S timeout). Repeat if timeout occurs.

1. Proximity: Bring the Zigbee remote or touch panel within 10cm of the lighting device.
2. Initiate Remote Pairing: Set the remote or touch panel into Touchlink commissioning mode (refer to its manual).
3. Confirmation: The remote will indicate successful linking, and the connected light will flash twice.

Diagram Description: Diagram shows a 'Zigbee Remote' positioned less than 10cm from the 'ZigBee LED Driver'. The driver is connected to AC Power. This illustrates the proximity required for TouchLink commissioning.

Notes on TouchLink:

• Direct TouchLink (neither device added to a ZigBee network): Each device can link with 1 remote.
• TouchLink after both added to a ZigBee network: Each device can link with max. 30 remotes.
• To control by both gateway & remote: Add remote and device to the network first, then perform TouchLink.
• After TouchLink, the device can be controlled by the linked remotes.

Device Management

5. Removed from a Zigbee Network through Coordinator or Hub Interface

From your ZigBee controller or hub interface, choose to delete or reset the lighting device as instructed. The connected light blinks 3 times to indicate successful reset.

Diagram Description: A screenshot of a user interface showing options to 'Move out', 'Reset', and 'Edit' a 'ZigBee LAMP' device within a 'Living room' context, indicating device removal from a network.

6. Factory Reset Manually

Method: Short press the "Prog." key 5 times continuously. If the "Prog." key is not accessible, re-power the device 5 times continuously.

Confirmation: The connected light will blink 3 times to indicate successful reset.

Notes:

• If the device is already at factory default setting, there may be no indication when factory reset is attempted again.
• All configuration parameters will be reset after the device is reset or removed from the network.

Diagram Description: Diagram shows the ZigBee LED Driver connected to AC Power (200-240V) and an 8-230V Push Switch Input. Output terminals are labeled V+, CW-, WW-. This diagram illustrates the device setup for manual factory reset.

7. Factory Reset through a Zigbee Remote (Touch Reset)

Prerequisite: Ensure the device is already added to a network, and the remote is added to the same one or not added to any network.

1. Initiate Reset: Re-power the device to start TouchLink Commissioning (180 seconds timeout). Repeat if necessary.
2. Proximity: Bring the remote or touch panel within 10cm of the lighting device.
3. Initiate Remote Reset: Set the remote or touch panel into Touch Reset procedure (refer to its manual).
4. Confirmation: The remote will indicate successful reset, and the connected light flashes 3 times.

Diagram Description: Diagram shows a 'Zigbee Remote' positioned less than 10cm from the 'ZigBee LED Driver'. The driver is connected to AC Power. This illustrates the proximity required for factory reset using a Zigbee remote.

8. Find and Bind Mode

Initiation: Short press the "Prog." button 3 times (or re-power the device 3 times) to start Find and Bind mode. The connected light flashes slowly to find and bind the target node (180 seconds timeout). Repeat if necessary.

1. Target Node Pairing: Set the remote or touch panel (target node) into find and bind mode and enable it to find and bind the initiator (refer to its manual).
2. Confirmation: The remote or touch panel will indicate successful binding, allowing control of the device.

Diagram Description: Diagram shows a 'Zigbee Remote' and the 'ZigBee LED Driver' connected to AC Power. This illustrates the setup for initiating the Find and Bind mode between a remote and the driver.

9. Learning to a Zigbee Green Power Switch

Initiation: Short press the "Prog." button 4 times (or re-power the device 4 times) to start Learning to GP switch mode. The connected light flashes twice (180 seconds timeout). Repeat if necessary.

1. Switch Pairing: Set the green power switch into Learning mode (refer to its manual).
2. Confirmation: The connected light will flash twice to indicate successful learning. The switch can then control the device.

Note: Each device can learn to a maximum of 20 Zigbee Green Power switches.

Diagram Description: Diagram shows a 'Zigbee Green Power Switch' and the 'ZigBee LED Driver' connected to AC Power. This illustrates the setup for learning the Green Power switch to the driver.

10. Delete Learning to a Zigbee Green Power Switch

Initiation: Short press the "Prog." button 3 times (or re-power the device 3 times) to start delete Learning to GP switch mode. The connected light flashes slowly (180 seconds timeout). Repeat if necessary.

1. Switch De-pairing: Set the paired green power remote into Learning mode (refer to its manual).
2. Confirmation: The connected light will flash 4 times to indicate successful deleting.

Diagram Description: Diagram shows a 'Zigbee Green Power Switch' and the 'ZigBee LED Driver' connected to AC Power. This illustrates the setup for deleting a learned Green Power switch from the driver.

11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)

Initiation: Short press the "Prog." button 4 times (or re-power the device 4 times) to enable the device to set up a Zigbee network. The connected light flashes twice to discover and add other devices (180 seconds timeout). Repeat if necessary.

1. Add Devices: Set another device or remote or touch panel into network pairing mode and pair it to the network (refer to their manuals).
2. Pair More: Pair additional devices and remotes as desired (refer to their manuals).
3. Bind Devices: Bind the added devices and remotes through Touchlink so they can be controlled by the remotes.

Notes:

• Each added device can link and be controlled by a maximum of 30 added remotes.
• Each added remote can link and control a maximum of 30 added devices.

Diagram Description: Diagram shows a 'Zigbee Remote' and the 'ZigBee LED Driver' connected to AC Power. This illustrates the setup for establishing a Zigbee network without a coordinator.

ZigBee Clusters and OTA

12. ZigBee Clusters Supported

Input Clusters:

• 0x0000: Basic
• 0x0003: Identify
• 0x0004: Groups
• 0x0005: Scenes
• 0x0008: Level Control
• 0x0300: Color Control
• 0x0b05: Diagnostics

Output Clusters:

• 0x0019: OTA
• 0x0006: On/off

13. OTA (Over-The-Air Update)

The device supports firmware updating through OTA. It will automatically acquire new firmware from the Zigbee controller or hub every 10 minutes.

Product Dimension

The physical dimensions of the device are approximately 210.0mm in length, 50.0mm in width, and 32.0mm in height.

Diagram Description: A diagram showing the physical dimensions of the ZigBee LED Driver, with measurements indicated as 210.0mm (length), 50.0mm (width), and 32.0mm (height).