Manuals+

Smart Video Doorbell

Quick Start Guideline

Please read it carefully before usage and save the manual for future use.

Install the Doorbell

Remove the Back-Bracket

1. Please put the fingers as the below picture.

2. Push down (Push up) the doorbell as the arrow shows.

[Image: Illustration showing how to remove the back bracket of the doorbell.]

Remove the back bracket before installation.

Remove the back bracket from the wall.

Power Supply Solution

A: Hard Wire Power Source

[Image: Diagram showing a hardwired power connection with an AC 12V~24V Transformer.]

AC 12V~24V Transformer (not included)

B: Powered By Battery

Micro USB Port For Battery Charging

Micro SD Card

Rechargeable 18650 Battery

Please re-charge the battery before it down to 5% power otherwise, it will be easy to dead.

[Image: Diagram showing battery power connection with Micro USB and Micro SD card slot.]

Chime Connection

Attention: Please connect doorbell with your phone firstly. Then pair the chime with the doorbell. (WIFI is not needed for Chime)

  1. Please hold and press the "Volume" Key on the chime.
  2. After the chime rings 1st sound (before 2nd sound), then press the doorbell button.
  3. If the chime is ringing after the doorbell pressed, then the chime is connecting to the doorbell.
  4. If not, remove the battery from the chime and install the battery again to try step 1 and Step 2 again.

[Image: Illustration of the chime with an indicator light.]

Fix the Doorbell to the Wall

Guide 1: Installed by the screws on the wall

Guide 2: Installed by the 3M industrial adhesive

[Image: Two guides showing installation methods: one with screws, one with adhesive tape.]

Tighten to secure

Connecting Doorbell to Your Phone

Download the APP - XSH Cam

Scan the following QR code or search "XSH Cam" on the app store to download the app. Note: Allow the app to send notifications to your phone firstly.

[Image: QR codes for Android and iOS, and a Google Play Store icon.]

Android | IOS | Google

Prepare Before Connection

Before you begin...

  1. Make sure the Xsh Cam app is installed to your device.
  2. Make sure that your device is connected to a 2.4GHz Wi-Fi network, NOT a 5GHz network.
  3. Make sure the rechargeable battery have been fully charged before connection.

Connecting Doorbell with App

  1. Tap "Add a Device".
  2. Tap "Setup Device". Note: If you have multiple devices, only setup one at a time.
  3. Before setup, make sure the device is in configuration. Long press the "Reset Button" for 5 seconds with a voice prompt "The camera is now ready to begin pairing". Then tap "Yes".
  4. The name of the Wi-Fi network will automatically be filled in. Enter the Wi-Fi password. The APP will fill the corresponding password automatically if connected with the same Wi-Fi, and you don't need to fill the password again. Then please tap "Next".
  5. The mobile device will emit sound waves. Keep quiet and make sure about 30cm distance between the phone and the device, and wait for the device to configure the network. Note: Do not mute your phone.
  6. If your doorbell fails to connect, reset the doorbell and repeat all the steps (please see the previous section, and reset the doorbell).
  7. After a successful connection, you will be prompted to create a name and password for your camera.

Note: Please select: "Non-Chinese Mainland" when you "select the area where the device is located". Otherwise, the cloud video will not work properly.

[Image: Screenshots of the app during the connection process.]

  1. Setup completed! The APP will enter the device list interface automatically. Congratulations! The device is ready for use.

Doorbell Function Instruction

Basic Settings

Go to "Device List", Click "⚙️" on the top right corner, to enter the following basic Settings.

[Image: Screenshot of the app showing basic settings options.]

Push mode: Change the Alert Mode

Share QR code: Share doorbell to family or friend

Step to share:

  1. Go to "Device list", Click "⚙️" on the top right corner.
  2. Click "Share QR code" to get the QR code to share.
  3. Take your family or friend's phone to download "XSH cam" app.
  4. Open "XSH cam", Click "Add a Device" - "Scan QR code".
  5. Scan the QR code you have shared. Then the doorbell has added more users.

Delete device / camera

Delete the doorbell, you will not get any notification, but the doorbell still works. And other connected phones will still be able to get the notification.

Menu Instruction

Device Settings

Click "Settings" on Menu - "Device Settings" To get more settings.

[Image: Screenshot of the Device Settings menu.]

Checking Recorded Video

Checking Recorded Video on Cloud storage

Please find the "cloud video" on the live video interface to check all cloud video.

[Image: Screenshot showing how to access cloud video recordings.]

SD Card / Cloud Storage Settings

Cloud Storage Settings

Cloud Video/Storage: Enable it to get cloud storage service. Note: Cloud Storage is free. 7-day loop recording. Each record only 8S. Couldn't change it.

Cloud video only 8S. Could Not Change. All cloud video could download to your phone.

SD card Storage Settings

Cloud Video/Storage: Disable it to get Micro SD card inserted for storage. Checking and SD card capacity and Format SD card here.

[Image: Screenshots showing cloud and SD card storage settings.]

Checking Recorded Video on SD card

Please drag the timeline to the yellow area to play the recorded video. Yellow area is the recorded Video.

[Image: Screenshot showing timeline for SD card video playback.]

SD video could download from SD card. Video Length setup by the active time.

Active Time / Dormancy Time

Recording time setup. Only available for SD card storage.

15S, 30S, 60S: Choose different record time after the PIR motion detection has been triggered for recording.

Always: Always in recording mode no matter if there is any movement. But it only worked for SD card storage and battery are easy to run out.

PIR detection: Motion Detection Setup

Note: In crowded environments, it is recommended to close or set the device to low sensitivity to reduce device arousal and call times to extend battery life.

[Image: Screenshots showing PIR detection settings.]

LED mode Setup:

Turn on / off the LED on the doorbell button.

Orentiation

Orentiation: Change the orientation of the video.

Envoriment

Envoriment: Turn on / turn off the Night IR or back light, highlight light compensation to make the video in a better view.

Power Frequency

Power frequency: Change the power frequency for the doorbell.

Note for using

  1. The device is powered by rechargeable lithium batteries. New battery is not fully charged. Please charge it firstly on the 1st installation. After power off, then you could charge it by connecting USB cable with USB adapter, power bank, PC or laptop. The mobile device APP will be prompted while the battery voltage is low. Please charge the device after received the reminder.
  2. Keep the camera in range of your router. Make sure to pick a place within range of your network. Thick or insulated doors can greatly reduce the strength of your Wi-Fi signal even if your router is close by, so you should try streaming video before you mount your camera.
  3. The device is a low power consumption intelligent product, can support remote wake up from the APP, PIR human detection, press doorbell wake up. The device will be works for 30 seconds after wake up then be in the resting state automatically and until to next waking up.

Setup Video instruction

1. Please Scan below QR code to watch the instruction guide.

2. Or Please go to YouTube, and search "NewPal M6 Video doorbell" to watch it.

[Image: QR code for video instructions.]

NewPal After-Sales Support

Email: support@newpal.shop | www.newpal.shop

PDF preview unavailable. Download the PDF instead.

B1ZEc1z2D3S Adobe Illustrator CS6 (Windows) Adobe PDF library 10.01