SONOFF SNZB-01P ZigBee Smart Button
Operating Instructions
Product Description
The Sonoff SNZB-01P is a smart ZigBee button. The weight of the equipment must be less than 1 kg and the equipment can be placed at a height of ≤ 2 m.
LED Indicator
The device features an LED indicator, a function button, and a pairing button. [Diagram Description: A circular device with a red LED indicator at the top, a function button in the center, and a pairing button on the side.]
| LED Indicator State | Description |
|---|---|
| Slow flashing | Pairing mode |
| Lights up for 3 seconds then turns off | Successful pairing |
| Stops flashing and turns off | Pairing failed |
| Fast single flash | Click, double-click, long press (when accessing Zigbee network) |
| Fast single flash | Not added to the gateway, press the pairing button. |
| Fast double flash | Added to the gateway, press the pairing button. |
Product Features
A small wireless button that fits even in your pocket, with pre-programmed actions for single click, double click, and long press to control multiple devices. Install it anywhere, stick it on, and use it. It can also be used in smart scenes with other intelligent devices.
- [Button icon] Activating multiple actions via one button
- [Battery icon] Replaceable battery
- [Notification icon] Low battery notification
- [Scene icon] Smart scene
These features depend on the operation of the Zigbee gateway. Download the eWeLink app and add the SONOFF Zigbee gateway.
Device Activation
[Diagram Description: Shows a finger removing a battery isolation tab from the device.] 1. Remove the battery isolation tab to activate the device. 2. When the unit is activated for the first time, it will enter pairing mode by default and the LED indicator will start to flash slowly.
[Diagram Description: Shows a finger pressing a button for 5 seconds, with a '5s' indicator.] 1. The device will exit pairing mode if pairing with the Zigbee gateway is not successful within 3 minutes. If you wish to re-enter pairing mode, press and hold the device's pairing button for 5 seconds until the LED indicator starts to flash slowly. 2. For device activation, a battery (CR2450) must be installed.
Add a Device to the Zigbee Bridge
On the main page of the Zigbee gateway in the eWeLink app, click the 'Add' sub-device option and wait for the addition process to complete.
[Diagram Description: Shows the eWeLink app interface. First screen shows 'ZB Bridge', 'Added: 0', 'Add Device'. Second screen shows 'Searching for device', 'Keep the device close to the hub.', a progress indicator '135s', and finally '1 device found'.]
If adding a device fails, move the device closer to the Bridge device and add it again.
Verify Effective Communication Coverage
Install the device in the desired location and then press the pairing button on the device. When the LED indicator flashes twice, it indicates that the product and a device on the same Zigbee network (router or repeater) are within effective range.
Installation
[Diagram Description: Three steps for installation. Step 1 shows applying adhesive 3M tape to a surface. Step 2 shows attaching a metal plate to the tape. Step 3 shows attaching the device to the metal plate.] 1. Apply adhesive 3M tape. 2. Fix the metal plate in the desired position. 3. Attach the device to the metal plate.
Specifications
- Model: SNZB-01P
- Input: 3.0V
- Wireless connection: Zigbee3.0
- Battery model: CR2477
- Operating temperature: -10°C-60°C
- Operating humidity: 5%-95% RH, non-condensing
- Housing material: PC
- Dimensions: 45x45x17.7mm
Factory Reset
The device can be reset to factory settings using the 'Delete device' option in the eWeLink app.
Safety Warnings
- Do not swallow the battery, risk of chemical burns. This product contains a battery.
- Swallowing batteries can cause severe internal burns in just 2 hours and lead to death.
- Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you suspect that batteries may have been swallowed or placed anywhere in the body, seek medical attention immediately.
- Replacing the battery with the wrong type may damage the protection (e.g., with certain types of lithium batteries).
- Discarding batteries in fire or a hot oven, crushing or cutting batteries may cause an explosion.
- Leaving the battery in a very hot environment may cause an explosion or leakage of flammable liquid or gas.
- Exposure of the battery to extremely low air pressure may cause an explosion or leakage of flammable liquid or gas.
