Install Guide

Document Details

V1.0 (20211208)

(V1.0 first published 20211208)

Firmware

Firmware version can be verified on command.verkada.com.

Introduction

What's in the box

• CD52 Outdoor Camera: A dome-shaped security camera.
• Mount plate (Attached to camera): A plate for mounting the camera, pre-attached.
• Mounting template: A paper template for marking drill holes.
• 2 Pole straps: Straps for mounting the camera on a pole.
• Cable gland wrench: A wrench for tightening the cable gland.
• T10 Security Torx screwdriver: A specialized screwdriver for securing the camera cover.
• 4 M4 x 25mm PH2 wall screws: Screws for wall mounting.
• 4 Wall anchors: Anchors for use with wall screws in drywall.
• Desiccant: A packet to absorb moisture.
• Conduit adapter (with 2 screws and anchors): An adapter for routing cables through conduit.

What you'll need

• A working Internet connection.
• 802.3af Power over Ethernet (PoE) switch, or a PoE injector. For operation below -20° C, use 802.3at PoE.
• A smartphone or laptop.
• A #2 Phillips screwdriver or power drill with a #2 Phillips driver bit.
• 1/4 inch (6.5mm) drill bit for wall anchors.
• 1/8 inch (3mm) drill bit for pilot holes.
• A Cat5 or Cat6 Ethernet cable with a 0.2-0.25 inch outside diameter (5-6.5mm).

Connect

• For easy registration and setup, scan the QR code on the product.
• If you prefer to manually register your product, please proceed to: verkada.com/start

Camera Details

Placement

• Mount the camera on a wall or ceiling. Try to keep the camera 8 to 10 feet above the ground.
• For best night vision, avoid overhangs or obstructions. These may reflect the camera's IR illumination and reduce the image clarity in night mode.

LED Behavior

• Solid Orange: Camera is on and booting up.
• Flashing Orange: Camera is updating firmware.
• Flashing Blue: Camera is recording data but cannot reach the server.
• Solid Blue: Camera is running, connected, and recording data.

Installation

Cable Gland Assembly 1/2

• To seal the Ethernet cable, disassemble the cable gland and feed the Ethernet cable through the baseplate through-hole.

Steps

• 1. Place the rubber seal around the cable. Push the plastic collar firmly over the rubber seal until it snaps into position.
• 2. Firmly insert the seal and collar assembly into the pass-through until it is secured in position.

Diagram Description: Shows the components of the cable gland assembly (Ethernet Cable, Through-hole, Rubber seal, Plastic collar, Metal nut) and the process of assembling the rubber seal and plastic collar into the through-hole.

Cable Gland Assembly 2/2

• 3. Place the metal nut over the rubber seal and engage the threads on the pass-through.
• 4. Gently tighten down the metal nut by hand. You should still be able to move the cable back and forth through the gland, but have enough resistance for it to remain in place.
• For detailed installation instructions, visit www.verkada.com/support

Diagram Description: Shows the process of attaching the metal nut to the cable gland assembly.

Assembly 1/2

• Please keep the protective film adhered to the clear bubble until completing the final step of installation.
• Use the provided T10 Security Torx security screwdriver to loosen the screws and lift the cover.
• Connect the camera to an 802.3af/at Power over Ethernet port on your network.

Diagram Description: Shows a T10 Security Torx screwdriver being used to lift the camera cover, and an Ethernet cable being connected to the camera's port.

Assembly 2/2

• An orange LED on the camera's Ethernet port indicates it is powered and booting up. A green LED on the Ethernet port indicates the camera is active.
• Gently pull the cable through the through-hole so it has some slack, but will not interfere with the top cover.
• Firmly tighten using the provided Cable gland wrench.
• Pulling the Ethernet cable too tight will strain the cable which may impact data performance.
• Too much slack in the Ethernet cable may create top cover installation issues.

Diagram Description: Shows the correct slack for the Ethernet cable with a checkmark icon, and incorrect slack (too tight or too much slack) with cross icons.

Mounting

• 1. Use the provided T10 security Torx security screwdriver to loosen the screws and lift the cover. To remove the mount plate, loosen the mount plate screws and twist the camera counter-clockwise. Lift the camera vertically off the base plate and set aside.
• 2. Use the provided mounting template to mark wall mount holes. For a junction box mount, use the mounting template to determine the correct hole pattern.
• 3. For a solid material like wood or metal, drill 1/8 inch pilot holes. Drive mounting screws directly into the pilot holes.
• 4. For drywall, drill 1/4 inch holes. Insert plastic anchors into holes and drive mounting screws into anchors.
• 5. To secure the camera, place it over the mount plate screws and twist counter-clockwise. Tighten the mount plate screws with a Phillips screwdriver.

Adjust

• Adjust your camera to the desired viewing angle. Use the online stream to confirm image orientation.
• Image can be flipped 180° online in Command.
• Default image orientation is indicated by markings on the lens face. Video orientation is also adjustable from within the Verkada application.

Diagram Description: Illustrates camera adjustment ranges: tilt up to 60 degrees, pan up to 350 degrees.

Secure

• Open and remove the desiccant pack from its outer pouch.
• Peel the backing from the double-sided tape on the desiccant pack.
• Place the pack directly on to the "Attach desiccant here" text on the interior camera shell.
• To secure the camera, align the top shell security holes with the baseplate and place the top shell back into its original position. Tighten the security screws using the provided T10 Security Torx screwdriver.

Diagram Description: Shows the desiccant pack being prepared and placed inside the camera shell, and the T10 Security Torx screwdriver being used to tighten the cover screws.

Grounding

• In order to attach the green-yellow grounding cable to the camera, perform the following:
• Align a 20AWG or larger grounding cable with a ring terminal and drive an M4-0.7 x 6mm screw (not included) through the terminal and into the threaded grounding point on the back of the device as shown above.
• Attach the other terminal of a grounding cable directly to a circuit breaker, ground rod or earth ground.
• This unit is powered by PoE through a UL Listed ITE.

Diagram Description: Shows the grounding point on the back of the camera, labeled "Ground".

Appendix

CD52 Compliance

Caution

• Maintenance and repair work must always be carried out by qualified technical personnel. Disconnect power from the unit when performing a maintenance task.
• Wiring methods used for the connection of the equipment to earth shall be in accordance with the National Electrical Code, ANSI/NFPA 70, and the Canadian Electrical Code, Part 1, CSA C22.1.
• The product must be installed and protected in a location that is not easily accessible and is away from impacts or heavy vibration.
• The device is only to be connected to PoE networks without routing to outside plants.
• If powered by a power adapter, the adapter should be properly grounded.
• Please contact certified dealers for power adapters.

PoE Adapter

• To reduce potential safety issues, only use the PoE adapter provided with the product, a replacement PoE adapter provided by Verkada, or a PoE adapter purchased as an accessory from Verkada.

Support

• Thank you for purchasing this Verkada product. If for any reason things don't work right, or you need assistance, please contact us immediately.
• verkada.com/support
• Sincerely, The Verkada Team