Olight Prowess Flashlight

In the Box

• Prowess Flashlight
• USB-A to USB-C Cable
• Holster
• Fixing Bracket
• Screws & Plastic Screw Anchors
• Detachable Base
• Holster Fixing Bracket
• 3M Adhesive Sticker for Base
• 3M Adhesive Sticker for Bracket
• Cushion Pad for Base
• MCC Cable (Note: MCC is not included in the package. If necessary, please purchase it from Olight Store. When using the MCC3 charging cable, the charging time is approximately 4.5 hours.)

Specifications

Table 1: Flashlight

Table 2: USB-A to USB-C Cable

Operating Instructions

1. Preparation: Remove the insulating film before first use (See Figure 1).

2. Charging: See Figure 2.

3. ON/OFF: Single press the switch quickly to turn on the light. When turned on, the flashlight will light up at the memorized brightness level. (Moonlight, Low, Medium, and High modes will be memorized when turned off. Turbo mode will be memorized as High mode; High mode output will last for 10 minutes before switching to Medium mode; Strobe mode will not be memorized.) Single press the switch again to turn off the light. The reverse light retains brightness memory for 1 minute after turning off and switches to the lowest output upon restart.

4. Lockout/Unlock: When the flashlight is off, press and hold the switch (for about 2 seconds) to access lockout mode (the flashlight will enter Moonlight briefly and then switch off to signal lockout mode activation). In lockout mode, if you operate the switch for a non-unlock purpose, the indicator at the center of the switch will briefly light up red to signal that the light is still in lockout mode. To unlock it, please press and hold the switch for about one second until the Moonlight is on. (See Figure 4).

5. Moonlight Mode: When the flashlight is off, press and hold the switch for over one second to access the Moonlight mode. If the light was turned off in Moonlight mode, simply press the switch. (See Figure 5).

6. Turbo Mode:

• Forward Light: Double press the switch quickly to activate Turbo mode, and double press again to return to the memorized brightness level. If the battery level is low, it returns to a lower output.
• Reverse Light: When the current brightness is ≥70%, double press the switch quickly to set the flashlight output to the lowest brightness. When the current brightness is <70%, double press the switch quickly to set it to the highest available brightness. (See Figure 6).

7. Switching Light Direction: Move the toggle switch upward for the forward light, and downward for the reverse light. (See Figure 7).

8. Forward Light Operation:

• Strobe: Press the switch 3 times or more to activate Strobe mode. To quit this mode, single press or press and hold the switch. (See Figure 8).
• Brightness Adjustment: When the light is on, press and hold the switch to adjust brightness. The flashlight will cycle through Low, Medium, and High modes, starting from the current brightness level. Release the button to select the desired brightness level. (Note: Moonlight and Turbo modes are not included in this cycle.) (See Figure 9).

9. Reverse Light Operation:

• Brightness Adjustment: When the light is on, press and hold the switch once to smoothly increase the brightness, and release to select the brightness level. To decrease the brightness level, press and hold again to smoothly decrease the brightness from the current brightness level. When the brightness level reaches its limits at the brightest or lowest setting, the light will flash twice to indicate that it has reached the highest or lowest level. (See Figure 10).

10. Battery Level Indicator: See Figure 11-1 & 11-2.

Mounting Bracket Application

Detachable Base Application: See Figure 12.

How to Use the Fixing Bracket:

1. Use tools to punch holes in the wall or wooden board.
2. Insert the screw anchors.
3. Remove the 3M adhesive sticker on the back of the fixing bracket and align it with the hole on the wall.
4. Secure the bracket in place by screwing in the screws. (Note: Please stick the 3M adhesive sticker on a flat and smooth wall or car panel).

(See Figure 13).

How to Take the Holster Out of the Fixing Bracket: Press the holster against the fixing bracket, then pull it up and out of the fixing bracket. (See Figure 14).

Warranty

Olight is proud to offer a lifetime warranty in Australia, China, France, Germany, and the USA. Coverage is being expanded to more countries, where a 2 or 5-year warranty is provided. The warranty covers defects in material and workmanship under normal use, excluding loss, theft, deliberate damage, or cosmetic damage. For complete warranty information, please visit Olight.com or your local Olight official website.

Customer Support Contacts:

• Australia: contact@olightstore.com.au
• Austria: kontakt@olightstore.at
• Canada: cs@olightstore.ca
• China: Wechat: olightcs
• France: cs@olightstore.fr
• Germany: kontakt@olightstore.de
• Italy: contatto@olightstore.it
• Japan: cs@olightstore.jp
• Korea: olightkorea@olight.com
• Spain: contacto@olightstore.es
• Thailand: cs@olightstore.co.th
• UK: contact@olightstore.uk
• USA: cs@olightstore.com
• For other countries and regions, please contact Global Customer Support: contact@olight.com

Compliance Information

EU Declaration of Conformity

Dongguan Olight E-Commerce Technology Co,Ltd declares that the equipment [Prowess] is in compliance with Directive 2014/30/EU and RoHS Directive 2011/65/EU & (EU) 2015/863. The full text of the EU declaration of conformity is available at: https://www.olight.com/download

WEEE Disposal and Recycling Information

Products bearing the WEEE symbol are waste electrical and electronic equipment. Dispose of them at designated collection points for recycling, appointed by the government or local authorities. Proper disposal and recycling help prevent negative consequences to the environment and human health. Contact local authorities for more information.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ISED Notice

This device complies with Industry Canada’s licence-exempt ICES standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-005.

The light source of this luminaire is not replaceable: when the light source reaches its end of life the whole luminaire shall be replaced.