m-e BELL-510 RX Wireless Doorbell Instruction Manual
m-e BELL-510 RX Wireless Doorbell

Introduction

Thank you for purchasing this radio doorbell from the Bell series.
Please read the operating instructions carefully and keep them for future use.
This radio doorbell can be used on the move thanks to its built-in rechargeable battery. The battery is charged via the integrated charger with the linchpin.
If a tuned-in radio doorbell transmitter is actuated, the radio doorbell plays a ring tone and/or signals the ringing visually, depending on the setting.
In addition, the radio doorbell is equipped with a repeater module and can forward received radio signals to more distant receivers of the Bell series.
Depending on the transmitter model, the range is between 100 and 500 meters under optimal conditions. The range is influenced by various factors, e.g. metal or UPVC door frames, walls or other devices operating on the same frequency.
All transmitters in the Bell series are compatible with this radio doorbell.
Product Overview
Product Overview

Note Icon Before using the radio doorbell for the first time, fully charge it at a 230V AC mains socket. The control LED (3) flashes green during charging and lights up permanently green when the battery is fully charged.

The ringing tone is set on the bell transmitter.

SCOPE OF DELIVERY

Radio doorbell BELL-510 RX
Operating and assembly instructions

LEGEND

  1. = Radio doorbell BELL-510 RX
  2. = Illuminated plate
  3. = Control LED
  4. = Plus button
  5. = Minus button
  6. = Colour selection button
  7. = Learning code button
  8. = Flip-plug
  9. = Flip-plug lock
  10. = Function selector switch
  11. = ON/OFF switch
COMMISSIONING

Switch on the radio doorbell with the ON/OFF switch (11).

  • Button Icon On
  • Button Icon  Of

Note Icon NOTE: If the radio doorbell is not in a socket, the control LED does not light up in standby. See also the section “Control LED”.

CHARGING FUNCTION + FLIP-PLUG

Press the lynch pin lock down to unfold the lynch pin and plug the radio doorbell into a mains socket. The charging process begins and the control LED flashes green. The radio doorbell does not have to be switched on for this. If the control LED lights up green continuously, the charging process is complete.
To be able to use the receiver on the move, push the linchpin back until it snaps back into place under the linchpin lock.

FUNCTION SELECTOR SWITCH

Use the function selector switch to choose whether the radio doorbell only plays the ring tone or only the light panel flashes or both together. Slide the switch to the desired position.

  • Button Icon Ring tone only
  • Button Icon Only flashing light panel
  • Button Icon  Ringtone and light panel

CONTROL LED

The control LED indicates various states.
If the radio doorbell is plugged into a 230V mains socket, the control LED flashes green to indicate the charging process.
If the LED lights up green continuously while the radio doorbell is plugged into a mains socket, the battery is fully charged.
If the LED flashes red, the battery is almost empty and the radio doorbell must be recharged.
If the LED flashes blue, the radio doorbell is in learning mode.

PAIRING THE TRANSMITTER

If no transmitter has been taught-in to the radio doorbell yet, the radio doorbell is in teach-in mode immediately after it is switched on; the control LED indicates this by flashing blue. Now trigger the desired Bell transmitter to learn it. The radio doorbell plays a ring tone and automatically leaves the learning mode.
To teach in another transmitter, press and hold the learning code button for approx. 3 seconds. The control LED flashes blue when the learning mode is activated. Then trigger the Bell transmitter to which the radio doorbell is to addition ally respond. The radio doorbell plays a ring tone and automatically leaves the learning mode.
This procedure must be repeated for each additional transmitter. A maximum of 4 transmitters can be taught in.

SETTING THE VOLUME

The volume can be adjusted in several steps via the two keys Plus (4) and Minus (5). Briefly press the Plus key to increase the volume one level or the Minus key to decrease the volume one level.

SETTING THE COLOUR OF THE LIGHT PANEL

The color of the light panel is set with the color selection key (6). A total of 7 different colure  are available. Each press of the key changes to the next color. The last color played back is automatically saved.

REPEATER FUNCTION

The radio doorbell has an integrated repeater function, i.e. it can forward radio signals from several transmitters of the Bell series and thus increase the range of the transmitters.
It is not necessary for the Bell transmitter to be tuned in to the radio doorbell in order to be forwarded. The repeater function is always active and cannot be switched off.
Bell transmitters that are tuned in to the radio doorbell are also forwarded. The radio doorbell itself, however, only rings for transmission signals that have also been tuned in to the radio doorbell.
This makes it possible, for example, for the radio doorbell in a two-family house to ring only when the bell button for family 1 is pressed. The radio signal of the bell button for family 2 is only forwarded without the radio doorbell itself ringing

Note Icon Note: There is a time delay of approx. 3 seconds between the reception of the signal until it is forwarded. The control LED indicates a forwarding by briefly lighting up.

FACTORY SETTINGS

To reset the radio doorbell to factory settings, press and hold the learning code button for 3 seconds until the control LED flashes blue. Release the button and hold it down again until the control LED stops flashing. After this, the radio doorbell is back in the delivery state and no more transmitters have been learned.
Then switch the radio doorbell off and on again. The control LED flashes blue and the radio doorbell is in learning mode. Now all the desired transmitters can be taught in again. Please refer to the section “Programming transmitters”.

TECHNICAL DATA

  • Operating voltage: 230V / 50 Hz
  • Battery: 3.7V/600mAh lithium-polymer battery
  • Power consumption (battery fully charged): <1W
  • Power consumption (battery being charged): approx. 2W
  • Frequency: 434MHz ; <10mW
  • Protection class: IP44
  • Temperature range: -20°C to +55°C

The battery is permanently installed; it can only be replaced by a specialist workshop.

NOTES

Exposure to strong static, electric or high-frequency fields (discharges, mobile phones, radio systems, mobile phones, microwaves) may cause functional impairment.

Cleaning and care

The surface of the housing can be cleaned with a soft cloth moistened with soapy water. Do not use abrasive cleaners or chemicals.

SAFETY INSTRUCTIONS

  • We accept no liability for damage to property or personal injury caused by improper handling or failure to observe the safety instructions. In such cases, all warranty claims are invalidated!
  • For safety and approval reasons (CE), unauthorized conversion and/or modification of the product is not permitted.
  • Do not carelessly leave the packaging material lying around, plastic foils/ bags,  polystyrene parts etc. could become a dangerous toy for children.
  • Consult a professional if you have any doubts about the operation, safety or connection of the appliance.
  • Handle the product with care – bumps, knocks or falling from even a small height will damage it.
  • The design of the product complies with protection class 2. Only a standard mains socket (230V~/50Hz) of the public mains supply may be used to power the device. Devices powered by mains voltage must be kept away from children.
  • Please therefore be particularly careful in the presence of children.

WARRANTY INFORMATION

This product is warranted to be free from defects in materials and workmanship for a period of 2 years from the date of purchase. This applies only if the appliance is used in the usual manner and is regularly maintained. The obligations of this warranty will be limited to the repair or re-installation of any part of the unit and will only apply on condition that no unauthorized modifications or attempted repairs have been made. Your statutory rights as a customer are in no way affected by this warranty

Please note! 

There is no entitlement to warranty in the following cases, among others:

  • Operating errors
  • Interference from other radio equipment (e.g. mobile phone operation)
  • External interference/impacts
  • Mechanical damage
  • Moisture damage
  • No proof of warranty (proof of purchase)

In the event of damage caused by non-observance of these operating instructions, the warranty claim becomes invalid. We accept no liability for consequential damage! We accept no liability for damage to property or personal injury caused by improper handling or non-observance of the safety instructions. In such cases, all warranty claims are invalidated!

LIMITATION OF LIABILITY

The manufacturer is not liable for loss or damage of any kind, including incidental or consequential damages, resulting directly or indirectly from the malfunction of this product.

These operating instructions are a publication of m-e GmbH modern-electronics,
An den Kolonaten 37, 26160 Bad Zwischenahn, Germany.
The operating instructions correspond to the technical status at the time of going to press. We reserve the right to make changes in technology and equipment

Customers Support

RoHS 2011/65/EU
RED 2014/53/EU
Support

Icons
Logo.png

http://www.m-e.de/download/ce/bell510rxce.pdf

Documents / Resources

m-e BELL-510 RX Wireless Doorbell [pdf] Instruction Manual
BELL-510 RX Wireless Doorbell, BELL-510 RX, Wireless Doorbell, Doorbell

Leave a comment

Your email address will not be published. Required fields are marked *